Graco QC5070, 4113 User Manual
234
© 1997 Graco 281-6-97
CARE AND MAINTENANCE
FROM TIME TO TIME CHECK YOUR ACTIVITY
CENTER for loose screws, worn parts, torn material
or stitching. Replace or repair the parts as needed.
Use only Graco®replacement parts.
REMOVABLE CLOTH SEAT may be machine
washed in lukewarm water on delicate cycle and
drip-dried. DO NOT MACHINE DRY. NO BLEACH.
TO CLEAN FRAME, use only household soap or
detergent and warm water. NO BLEACH.
PARTS LIST
CHECK that you have all the parts listed
below BEFORE assembling your
Entertainer activity center. If any parts
are missing, call Customer Service at
1-800-345-4109.
Tool required: Screwdriver
Model 4113
Teether
toy
Beads and bar
Seat
Clicker
and screw
Tray and seat ring
Base
Seat lock
and screw
Failure to follow these warnings and the assembly
instructions could result in serious injury or death.
Strings can cause strangulation! DO
NOT place items with a string around
your childs neck, such as hood
strings or pacifier cords. DO NOT
suspend strings over the activity
center or attach strings to toys.
Never leave child unattended. Always
keep child in view while in this product.
Never lift or carry this product with
child in it.
Product may gradually move across
the floor as child plays in it. Watch for
movement of product and be sure
child stays away from hazards in the
area such as stairs, cords, hot liquids,
pools, sources of heat and anything
else that may injure your child.
Do not use product with a child who
can tip over or climb out of product.
To avoid tipovers, place product on
flat, level floor/ground. Adjust legs to
same height so that the tray is level
before placing child in product.
Congratulations on your purchase of a
Graco
®
Entertaineractivity center!
Graco is the recognized leader in the
design and manufacture of quality baby
products. We believe your new Graco
®
Entertaineractivity center is a wise
choice, promising many hours of
enjoyment for your baby.
Before using your activity center, please
take a few minutes to read this Owners
Manual. The short time you spend reading
these instructions will help you to use your
activity center properly.
Customer Satisfaction
Our goal is to make every product the best it
can be! We are also committed to supporting our
products after purchase. If you would like to speak
with Graco about your product, please contact our
Customer Service Department at 1-800-345-4109.
Our knowledgeable staff will be ready to answer
any questions you may have concerning parts,
use or maintenance. When you call, please have
the model and serial numbers ready so your
call may be processed quickly and efficiently.
Model No. __________
Serial No. __________
Dear Customer,
Please fill in the
model and serial
numbers above
from the label
under the tray
of your new
Entertainer
activity center.
OWNERS
MANUAL
The Entertainer
Activity Center
by
Leg (3)
THIS PRODUCT REQUIRES ADULT ASSEMBLY.
READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF THIS PRODUCT.
If you experience any difficulties, please contact the Customer Service Department.
KEEP INSTRUCTIONS FOR FUTURE USE.
THIS PRODUCT IS FOR USE ONLY by a child who is able to sit upright unassisted,
unable to walk, weighs less than 30 pounds, and is less than 32 inches tall.
EXCESSIVE EXPOSURE TO SUN OR HEAT could cause fading or warping of parts.
DO NOT USE THIS PRODUCT if it is damaged or broken.
THIS PRODUCT IS NOT INTENDED FOR COMMERCIAL USE.
5
281-6-97
6 87
Step 9.
Assemble the toys on the tray as shown.
NOTE: Toys may be removed from tray
for cleaning or storage.
Tighten screw until
clicker does not
move freelyDO
NOT overtighten
then loosen screw
slightly.
Insert teether
stalk into the tray.
Push beads firmly over the
retaining loops on bead bar.
Insert end with loops into the
hole directly over leg, and turn
bar until fully seated (retaining
loops do not go into the hole).
Then plug forked end of bar
into the square hole in the tray.
Insert
this
end
first
Retaining
loops
Snaps visible
RIGHT
WRONG
Buttons
Line
To Assemble Your
Entertainer Activity Center
Step 1.
Turn the tray over and
locate the hole that the
seat lock screws into. Place
the seat lock on the tray as
shown and screw it to the
tray. DO NOT overtighten
screwseat lock must be
free to slide.
Step 2.
Four tabs are located
behind the indentations
inside the seat ring.
Remove the seat ring by
pulling the four tabs out
from under the tray, one
at a time, while lifting the
seat ring.
Step 3.
Put the seat ring upside
down inside the cloth seat.
The high side of the seat
ring goes to the back of the
seat, where the warning
label is located.
Attach the seat to the seat
ring by tucking the seat
edge into the channel and
snapping the grommets on
the pegs.
Step 4.
Turn the seat over and
push the seat down into the
seat ring.
Step 5.
Snap the seat ring back
onto the tray. Make sure all
four tabs are snapped onto
the inside lip.
Pattern side UP
Solid color inside
Grommet
Pattern side
Step 6.
Turn tray over. Push one leg into socket in tray exactly as
shown until it snaps into place. Repeat for other two legs.
Step 7.
On top of tray, CHECK that
snaps are visible through
slots. Pull on leg to be sure it
is securely attached.
Step 8.
Slide the leg tubes on the tray onto the leg tubes on the
base as shown.
HINT: If a tray leg tube will not slide onto the base leg
tube, twist the base tube slightly to line up the parts.
Push in the buttons on each of the upper leg tubes
and adjust the activity center to the desired height.
The bottom edge of the upper tubes must be even with
one of the three lines on the lower leg tube.
CHECK that all three leg tubes are set to the same
height.
To Use the Seat Lock
Push gently on latch and
turn the seat until latch
engages in one of the four
stop positions.
To allow seat to swivel
again, pull lock out.
To Adjust the Seat Height
Do not adjust height while child is in
activity center.
Step 1.
Press in the buttons on
each leg to adjust seat
to desired height. The
bottom edge of the upper
tubes must be even with
one of the three lines on
the lower leg tube.
For your childs safety, all three legs
must be set to the same height. Tray must be level.
Button
faces seat
Loading...