Graco PD44 User Manual

Graco® PD44
Patented Meter, Mix and Dispense Valve for Two-Component Micro Dispensing
Graco PD44 Valve for Precise Micro-Dispensing
1.0cc
0.50cc
0.25cc
0.1cc
0.005cc
1/16" Dia.
1/8" Dia.
3/16" Dia.
1/4" Dia.
To determine dot volume:
Volume = D 2
* ½ the volume of a sphere
3
x 0.5236*
Exceptional Performance
The Graco PD44 Valve is specifically designed to dispense small amounts of water thin to paste viscosity materials from 0.005 cc’s to 5 cc’s. The metering rods are matched with machined seals for improved seal life. There are no material hoses between the rod pump outlets and mixer inlet which eliminates potential ratio or shot size problems (phasing) due to hose expansion and contraction.
Graco PD44 Valve features
• Specically designed to accurately dispense shots of two-component epoxies, urethanes, silicone and most reactive resin systems
• Improved low viscosity spool design
• Rod positive displacement metering
• Precise mix ratio and shot repeatability
• Eliminates cleaning and potential hardening
of materials in the valve
D
Bead Sizes Dot Sizes
Bead Size = Full diameter of bead
Key Applications
Potting
Gasketing
Sealing
Encapsulation
Syringe Filling
Key Industries
Automotive Electronics
Consumer Electronics
Medical
Sporting Goods
Automotive Components (ex: lighting)
Appliance
Product Assembly
System Configuration
How It Works
Materials remain separate until injected into static mixer.
The patented Graco PD44 Valve features balanced inlet/outlet spool assemblies that do not displace material while shifting from the reload to the dispense position. This allows pressure feeding of the “A” and “B” components up to 1200 psi during reloading while isolating the materials from the mixer inlet. Upon shifting to the dispense position, an accurate volume of “A” and “B” components is injected into the disposable mixer inlet by rod displacement metering technology
Reload
Spools shift to the right
• Material feed inlets are opened
• Materials are transferred into the metering chambers
by a pressurized feed system
• Outlet ports are blocked
• Metering rods are retracted to a precise position determining
the volume of each material
Shift
The balanced spool assemblies shift to the dispense position
• Material path to the mixer inlet is opened
• Material feed inlet ports are blocked
• Metering rods remain in the retracted position
Dispense
Metering rods drive down
• A and B materials are simultaneously dispensed from the metering chamber into the disposable mixer
• A and B materials are dispensed at the predetermined volume ratio. Upon completion of the dispense stroke, the metering rod and spool assemblies shift back to the reload position
RELOAD
SHIFT
DISPENSE
1
Graco PD44 Valve
Patented PD44 Metering Valves
Meter, mix and dispense shots from 0.005 to 5 cc’s and handle material ratios from 1:1 to 25:1.
Metering Drive
Machined Seals
A longer life seal means less down time and reduces maintenance costs
Metering Drives
Manual control of shot size
Pneumatically-driven valves have a
micrometer adjustment to easily set the desired shot size.
Programmable shot size
Linear actuator provides shot size control.
Useful feature when different shot sizes are required.
“A” and “B” Precision Metering Rods
Accurate and repeatable volume ratio control
Upgraded Sensors
Faster response and reliable position control for long term performance
Balanced Inlet/Outlet Spool/Sleeve Assembly
Accurate reloading and dispensing to ensure ratio accuracy
Material Feed Inlet Block
Keeps material separate until in the mixer, eliminating the need for solvent flush
Shroud and Disposable Mixer
Reduce waste and eliminate the need
to solvent flush your system
Programmable flow and shot size
Electric drive motor programs shot
size and flow rate, providing precise control for applying continuous beads of material. This is key when adapting the PD44 valve to X-Y-Z motion tables.
2
Controller
Pneumatic/Linear Actuator Controller
Manual and Programmable Shot Size
Sensors in the valve monitor the position of the spool assemblies
and metering rods. These sensors interface with the control panel to assure proper valve operation.
PD44 systems can help you save material and labor costs for a variety of dispensing applications, whether you are using manual, semi-automated or automated manufacturing processes.
Electric Controller
Programmable Flow and Shot Size
This free standing table top controller includes a NEMA 23 stepper motor for precise ow and shot control.
Other features include:
• A monochrome touch screen, audio alarm
and footswitch *
• Seven programmable shot sizes and ow rates
Controller Screen Shots
Graco PD44 Valve Controller
• Simple operator interface for day-to-day operation
• Password protection for added security
• Anti-gel/purge timer to protect static mixer
from curing
Shot size screen
• Programmable shot sizes for fast operator set up
• Shot size storage for quick change between parts
• Customer I/O connections for integration with auxiliary equipment.*
*Also included with Pneumatic/Linear actuator controller
Status screen
• System monitoring for productive planning
• Scheduling preventative maintenance
Feed System
3
Cartridge Feed Systems
Transfer low to medium viscosity materials to the PD44 valve by placing cartridges of various sizes into pressurized containers.
Transfer Pumps and Rams
Pump low to high viscosity materials directly from bulk containers. Use pail and drum rams, transfer pumps and feed hoses as required.
Reservoir Tanks
Transfer low to medium viscosity materials to the PD44 valve using various sized reservoir tanks.
Complete System
PD44 with pneumatic controller, manual linear actuator and dual one gallon transfer pump feed package.
Technical Specifications
“A” and “B” Metering Rods..............................A wide selection of standard size metering rods are available
depending on the ratio and shot sizes desired. Custom sized metering rods can be machined to accommodate most material ratios. The standard construction of the main body is 303/304 stainless steel.
The standard construction of the metering assembly is a nitrided tool steel rod and a nitrided
tool steel tube. Optional materials include stainless steel rod with UHMW tube and a tungsten rod with UHMW tube.
Ratio Range .............................. 1:1 to 25:1 by volume depending on the size of the metering rods selected.
Shot Size Capability ................................................ 0.005 cc’s to 5.0 cc’s depending on the size
of the metering rods selected.
Cycle Rate ....................................................Up to 60 cycles per minute with pneumatic drive
Max cycle depends on the length of the stroke, size of metering rods, material viscosity, mixer, outlet needle employed and any back pressure or flow limitations created by the product into which material is being dispensed.
Balanced Inlet/Outlet Spool Assemblies .................................The pneumatically actuated spool assemblies
keep the “A” and “B” materials separate in the valve and isolate the material inlets from the outlets to the mixer. The standard construction of the spool assembly is a nitrided
tool steel spool and a nitrided tool steel sleeve. Optional materials include stainless steel spool with UHMW sleeve and a tungsten spool with UHMW resleeve.
Material Feed System ..........................Pressure feed systems including cartridges, tanks and transfer pumps,
can be employed to feed “A” and “B” components up to 1200 psi. The appropriate selection of feed equipment is dependent. on material viscosity and processing requirements.
Accessories ..........................................Level controls, agitators, follower plates, vacuum degassing,
nitrogen blanketing, etc. are readily available.
Mixers .........................Disposable Posimixer
®
is available in sizes from 1/8 in (3.175 mm) to 3/8 in (9.525 mm) in diameter and in various number of elements to provide thorough blending of most reactive resin systems. Lab tests may be required to determine the specific mixer required for a particular application.
Disposable Needles .............................................................From 14 gauge to 30 gauge
A variety of Luer Lock needle sizes are available to adapt to the Posimixer outlets.
Metering Drives .............................The standard drive is an air cylinder with a precise manual stroke adjust.
Additional drive options include: A linear resistive transducer air cylinder providing electronic shot size control. A stepper or servo ready lead screw actuator for precise shot and flow control.
Machine Controls..............................................Free standing tabletop control panels are available
for air cylinder and motor driven valves.
Standard hardware includes: Monochrome touch screen, audio alarm and foot switch. Standard features include: Purge timer, cycle counter and totalizer. Motor driven controls include a NEMA 23 stepper motor
featuring shot size and flow rate control.
Dimensions ................................ Body – 15 in (381 mm) H x 4 1/8 in (105 mm) L x 7 9/16 in (192 mm) W
Mixer – Add 4 in (100 mm) to 14 3/4 in (375 mm) H to the height. Pneumatic Controller – 15 in (381 mm) W x 12 in (305 mm) D x 13 in (330 mm) H.
Electric Controller – 20 in (508 mm) W x 8 in (203 mm) D x 20 in (508 mm) H.
Weight...................................... PD44 valve only – 14 lb (6.35 kg) – 15 lb (6.80 kg) (depends on drive)
PD44 bench stand and controller – 50 lb (22.68 kg) to 75 lb (34.02 kg) (depends on options)
Service Requirements ................................................ Normal industrial compressed air supply -
0.1 (0.0028 m
3
/min) to 2.58 CFM (0.07 m3/min) at 80 psi (5.62 kglcm2).
Electric – 120/240V, 50/60Hz.
ABOUT GRACO
Founded in 1926, Graco is a world leader in fluid handling systems and components. Graco products move, measure, control, dispense and apply a wide range of fluids and viscous materials used in vehicle lubrication, commercial and industrial settings.
The company’s success is based on its unwavering commitment to technical excellence, world-class manufacturing and unparalleled customer service. Working closely with qualified distributors, Graco offers systems, products and technology that set the quality standard in a wide range of fluid handling solutions. Graco provides equipment for spray finishing, protective coating, paint circulation, lubrication, and dispensing sealants and adhesives, along with power application equipment for the contractor industry. Graco’s ongoing investment in fluid management and control will continue to provide innovative solutions to a diverse global market.
GRACO LOCATIONS
MAILING ADDRESS
P.O. Box 1441
Minneapolis, MN 55440-1441 Tel: 612-623-6000
Fax: 612-623-6777
AMERICAS
MINNESOTA
Worldwide Headquarters Graco Inc.
88 -11th Avenue N.E. Minneapolis, MN 55413
EUROPE
BELGIUM
European Headquarters
Graco N.V.
Industrieterrein-Oude Bunders Slakweidestraat 31
3630 Maasmechelen, Belgium Tel: 32 89 770 700
Fax: 32 89 770 777
ASIA PACIFIC
AUSTRALIA
Graco Australia Pty. Ltd. Suite 17, 2 Enterprise Drive Bundoora, 3083 Victoria, Australia Tel: 61.3.94678558
Fax: 61.3.94678559
CHINA
Graco Hong Kong Ltd. Shanghai Representative Office Room 118 1st Floor
No.2 Xin Yuan Building
No.509 Cao Bao Road Shanghai, P.R. China 200233
Tel: 86 21 649 50088
Fax: 86 21 649 50077
INDIA
Graco Hong Kong Ltd. India Liaison Office Room 103, Level 4, Augusta Point Golf Course Road Gurgaon, Haryana, India 122001
Tel: +91 124 435 4208
Fax: +91 124 435 4001
JAPAN
Graco K.K.
1-27-12 Hayabuchi
Tsuzuki-ku Yokohama City, Japan 2240025 Tel: 81 45 593 7300
Fax: 81 45 593 7301
KOREA
Graco Korea Inc.
Choheung Bank Building
4th Floor #1599
Gwanyang-Dong, Dongan-Ku,
Anyang-Si, Gyunggi-Do,
Korea 431-060 Tel: 82(Korea) 31 476 9400
Fax: 82(Korea) 31 476 9801
SALES/
DISTRIBUTION/
SERVICE
Graco Ohio
Customer Service
800-746-1334
Fax 330-966-3006
Call today for product information or to request a demonstration.
877-84GRACO (1-877-844-7226) or visit us at www.graco.com.
Graco Inc. is registered to I.S. EN ISO 9001
©2008 Graco Inc. 337497 Rev. B 10/08 All written and visual data contained in this document are based on the latest product information available at the time
of publication. Graco reserves the right to make changes at any time without notice. All other brand names or marks are u sed for identifi cation p urposes and are trademar ks of t heir res pective owners.
Loading...