Graco J Series, A Series, 207-279, 223-634 Instructions-parts List Manual
INSTRUCTIONS–P
This
manual contains IMPORT
W
ARNINGS AND INSTRUCTIONS
READ AND RET
AIN FOR REFERENCE
ARTS LIST
ANT
55 Gallon (200 Liter) Drum Size
306–934
Rev. K
Supersedes H
AIR–POWERED
150
psi (10.5 bar) MAXIMUM INBOUND AIR PRESSURE
RAM
Model 207–279, Series J
For
use with high pressure extrusion pumps (see page 3).
Model 223–634, Series A
For
use with Check–Mate 450 pumps
with Displacement Pump 222–790 (see page 3).
TABLE OF CONTENTS
Safety Warnings 2.
Pump
Selection Chart3. . . . . . . . . . . . . . . . . . . . . .
Installation 4–6
Operation 7
Troubleshooting
Service 9–12
Parts
Model 207–279 14, 15
Model
Accessories 18
Dimensional
Technical
Warranty Back
Toll–Free
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drawings and Lists
223–634 16, 17
Data
.
. . . . . . . . . . . . . . . . . . . . . .
Graco Phone Numbers
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chart8. . . . . . . . . . . . . . . . . . . . .
.
. . . . . . . . . . . . . . . . . .
.
. . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drawing
.
. . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .
.
.
Back Cover
Cover
Back Cover
19.
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
Model
207–279 Shown
SAFETY
W
FOR PROFESSIONAL USE ONLY. OBSERVE ALL WARNINGS.
Read and understand all instruction manuals before operating equipment.
EQUIPMENT MISUSE HAZARD
General
Any
ing parts, or using worn or damaged parts, can cause them to rupture and
result
DO
SURE
NEVER
function
CHECK
parts
ALWAYS
instruction
Safety
misuse of the ram or accessories, such as overpressurizing, modify
in serious bodily injury or property damage.
NOT exceed 150 psi (10.5 bar)
to the ram.
alter or modify any part of the ram; doing so could cause it to mal
and make it dangerous to operate.
all equipment regularly and repair or replace worn or damaged
immediately
use the ram only for its intended purpose as
.
manual.
MAXIMUM INBOUND AIR PRES
described in this
-
-
-
ARNINGS
Pressure
To
reduce the risk of serious bodily injury
in the eyes or on the skin, or injury from moving parts, always relieve
ing
all
air and fluid pressure in the system before checking or repairing the
ram
1. Shut
2.
3.
4. T
5.
6. Leave
MOVING PARTS HAZARD
Moving
ram plate/pump fluid inlet moves when the ram is in operation. Keep
hands
fluid container when raising or lowering the ram. Keep clear of all moving
parts when starting or operating the ram or pump. Before checking or
servicing the ram or pump, always follow the Pressure Relief
Procedure,
Relief Procedure
, including fluid injection, splash
or any other part of the system and
of
f the air to the pump and ram.
Open the bleed–type master air valve to relieve trapped air
Shut of
f the ram director valve.
rigger the gun/dispensing valve to relieve fluid pressure.
Open all fluid drain valves in the system.
the drain valves open until you are ready to
again.
parts can pinch or amputate your fingers
and fingers away from the ram plate, pump fluid inlet, and lip of the
above.
when shutting down the system.
.
spray/dispense
or other body parts. The
-
For
Pump Model and Description
PUMP SELECTION CHART
Use Ram Model
10:1 Monark, Model 222–770, with Severe–Duty Check–Mate 450 Displacement Pump
20:1 President, Model 222–768, with Severe–Duty Check–Mate 450 Displacement Pump
34:1 Senator
55:1 Bulldog, Model 222–778, with Severe–Duty Check–Mate 450 Displacement Pump
15:1 Senator
15:1 Senator
25:1 Senator
25:1 Senator
10:1 Bulldog, Model 222–526, with Severe–Duty Displacement Pump
10:1 Bulldog, Model 204–287, with Nitralloy Displacement Pump
10:1 Bulldog, Model 207–172, with Stainless Steel Displacement Pump
25:1 Bulldog, Model 222–527, with Severe–Duty Displacement Pump
25:1 Bulldog, Model 217–565, with Nitralloy Displacement Pump
40:1 Bulldog, Model 222–535, with Severe–Duty Displacement Pump
40:1 Bulldog, Model 220–448, with Nitralloy Displacement Pump
, Model 222–769, with Severe–Duty Check–Mate 450 Displacement Pump
, Model 222–518, with Severe–Duty Displacement Pump
, Model 222–489, with Nitralloy Displacement Pump
, Model 222–525, with Severe–Duty Displacement Pump
, Model 222–519, with Nitralloy Displacement Pump
223–634*
223–634*
223–634*
223–634*
207–279
207–279
207–279
207–279
207–279
207–279
207–279
or
954–285**
207–279
207–279
207–279
207–279
20:1 King, Model 222–539, with Severe–Duty Displacement Pump
20:1 King, Model 222–248, with Nitralloy Displacement Pump
20:1 King, Model 220–648, with Stainless Steel Displacement Pump
55:1 King, Model 222–545, with Severe–Duty Displacement Pump
55:1 King, Model 217–566, with Nitralloy Displacement Pump
Mounting Kit 222–776 is required to mount a Check–Mate 450 Pump on Model 223–634 Ram.
*
**
Stainless Steel Ram 954–285 does not include ram plate or tie rods.
NOTE: Model
207–279 Ram is shipped with optional seals (51 and 75), seal plates (76), an intake adapter (55), and
a mounting plate (58) for use with pumps not listed above (see the
installation
Technical
information regarding pumps
Assistance at 1–800–543–0339.
not listed in this chart, contact your Graco representative or Graco
parts
list on page 15). For application and
207–279
207–279
207–279
or
954–285**
207–279
207–279
Loading...