Graco IMONITOR 2791, IMONITOR 2795 User Manual 2

RACO

Replacement Parts

• Warranty Information (USA)

Product Registration (USA)

To purchase parts or accessories or for warranty information in the United States, please contact us at the following:

www.gracobaby.com

1-800-345-4109

To register your Graco product from within

the U.S.A. visit us online at

www.gracobaby.com/productregistration.

We currently do not accept product registrations

from those living outside the

United States of America.

Parent’s Unit (A3940) Model 2791 - 1 unit Model 2795 - 2 units

Nursery Unit (A3930) Model 2791

Clip

Product Features

Green = batteries ok Red = batteries low

Power Volume:

Up/Down

Nursery Unit (A3929) Model 2795

Green when charging

DC Adapter Jack with rubber cover

Rechargeable Battery Pack Model 2791 - qty.1 Model 2795 - qty.2

Docking Station (A3921) Model 2791 -1 unit Model 2795 - 2 units

DC Adapter Jack

Parent Finder

Channel Selector

ON/OFF

Channel Selector

ON/OFF

Battery Cover

AC Adapter Model 2791 - Qty. 2

Model 2795 - Qty. 3

Failure to follow these warnings and the assembly

2791/2795

instructions could result in serious injury or death.

This device is designed only to monitor the sounds of your child. It will not alert you to your child’s silent activities. When using the monitor, you must still provide the supervision necessary for the continued safety of your child. This product is not designed or intended for use as a medical monitor. Always be sure that both the transmitter and receiver are working properly and are within range of each other.

• STRANGULATION HAZARD. Keep the adapter cords out of the reach of children. Do not use with extension cords.

• DO NOT place the Nursery Unit or its cord within your child’s reach. Do not put the Nursery Unit inside a crib or play yard.

• Use ONLY with 110-120 volt AC electrical outlets.

• Protect the AC adapter cords. Place them so they are not walked on or pinched by furniture or other items.

• Allow for proper ventilation when units are in use. Do not cover the Nursery Unit or Parent Units with any object such as a blanket. Do not place it in a drawer or in any location which would muffle the sound or interfere with the normal flow of air.

• DO NOT immerse any part of the Nursery Unit, Parent Units, or docking station in water. Clean only with a dry cloth.

• DO NOT place unit near water and moisture. Do not use the Nursery Unit outdoors. Do not use the Nursery Unit near possible wet areas, such as a bathtub, shower, wash basin, sink, laundry tub, swimming pool, wet basement, etc.

• Keep Nursery Unit away from heat sources, such as fireplaces, radiators, stoves, and TVs or other appliances. Heat can damage the case or electrical parts.

• DO NOT use the Nursery Unit if:

• The adapter cords or plugs have been damaged.

• The unit has been exposed to liquids.

• Unit has been dropped or is damaged.

• DO NOT OPEN THE NURSERY UNIT, PARENT UNITS, DOCKING STATION OR ADAPTERS. No user-serviceable parts inside. Risk of electrical shock, fire or death.

• The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.9”) from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC Statement:

WARNING Modifications not authorized by the manufacturer may void users authority to operate this device.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful inter user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a cir

•

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

ference to radio or television reception, which can be determined by turning the equipment off and on, the

cuit different from that to which the receiver is connected.

Graco Children’ 150 Oaklands Blvd. Exton, P 1-800-345-4109

A 19341

s Products

Battery Installation

arent Unit

• The battery must be plugged into the Parent Unit before the unit will be ready for use. Remove the battery door cover on the Parent Unit with a key or flat blade screw driver. Remove the battery pack from the packaging and plug into the back of the unit. Place

he battery pack into the recess and press the wire into the slot on

t the side. Replace the battery door.

Nursery Unit

• Turn the unit over, and use screw driver to remove the battery door.

• Place 3-AAA (1.5V-LR03) batteries into the battery compartment. Note the proper orientation of the batteries.

• Place the battery door back on the unit.

• Please remove a dead battery promptly. A dead battery left in the unit may leak, damaging your unit.

• Do not attempt to recharge a non-rechargeable battery.

• A rechargeable battery CANNOT be recharged by plugging the AC adapter into the Nursery Unit.

• Remove the batteries from the unit if it is no longer being used or will be stored for an extended period of time.

Plug in cord

Using AC Adapters

• The Parent Unit(s) can use either the rechargeable battery that comes with the unit or standard 120 volt AC household current. The Nursery Unit uses 3-AAA (1.5V-LR03) batteries or standard 120 volt AC household current.

• To use AC adapters, plug the connector on the cord into the AC adapter jack on the side of the Parent Unit (under the rubber cover) and the back of the Nursery Unit. If using the docking station, plug the AC adapter jack into the back of the docking station. The Parent Unit may now be placed in the docking station. Then plug adapter into a standard wall outlet.

• Use ONLY the Graco adapters included with the unit. Do not use these adapters with other equipment under any circumstances.

• If units do not work, check that AC adapters are plugged into working outlets.

• When electricity is off (from a power failure, etc.), the Nursery Unit will operate on 3-AAA (1.5V-LR03) batteries. If the Power LED is not lit, turn the power off and then back on to the Nursery Unit. A green LED indicates that the batteries are fine. A red LED indicates that the batteries are low. If the LED does not light at all, then replace the batteries. The Parent Unit will operate if the rechargeable battery is charged.

Selecting Channels

• In case you are experiencing some interference, the channel on the Nursery Unit can be changed by pressing the “ch” button on the side of the unit. The Parent Unit will automatically scan all of the available channels until it locks on to the Nursery Unit. If you are still experiencing interference, press the channel button on the side of the Nursery Unit up to 6 times until a good channel is found.

Low Battery Indication

Parent Unit

• When the battery is low in the parent unit, the LED bar on the side of the unit will change from green to red and you will hear a series of 3 audible beeps every 5 seconds. If operated too long on a low battery, you may also experience a poor signal and the connection LED on the front of the parent unit may change from green to red and you will begin to hear a continuous audible beep from the Parent Unit.

• You may either turn off the unit, plug in the A/C adapter or place the unit in the docking station to recharge the batteries.

Nursery Unit

• When the batteries are low in the Nursery Unit, the power LED will change from green to red. You may also experience a poor signal and the connection LED on the front of the Parent Unit may change from green to red and you will begin to hear the Parent Unit beep.

• You may either turn off the unit, plug in the A/C adapter or replace the batteries.

Out of Range Indication

• If the Parent Unit begins to lose the signal from the Nursery Unit, the connection LED (bottom Sound Light LED) will change from green to red. Additionally, a continuous audible beep will be generated to warn the user that the connection to the Nursery unit has been lost.

• Immediately move the Parent Unit closer to the Nursery Unit to regain connection.

• Once connection has been re-gained, the connection LED will change from red to green and the audible beep will stop.

***Note: It is not uncommon for the Parent Unit to occasionally lose and regain connection with the Nursery

Unit in environments that have a significant amount of obstructions.

Setting Up the Baby Monitor

***NOTE: It is very important that the steps below be followed for first time power-up.

1. For optimum operation, it is best to charge the batteries in the Parent Units for at least 16 hours prior to use. The rechargeable batteries need to be installed into the Parent Unit before charging - refer to the “Battery Installation” section. DO NOT turn on power while the unit is charging for the first time.

2. Place the Nursery Unit within 10 feet (3 meters) of your baby. Plug an AC adapter into the jack on the back of the Nursery Unit. Plug it into a working 120 volt AC outlet.

3. Aim the Nursery Unit toward your baby. Check that there are no walls or large objects that could block sound transmission.

4. Place the Parent Unit within five (5) feet (1.5 meters) of the Nursery Unit and turn on the Parent Unit using the On/Off switch on the side of the unit. All of the Sound Light LEDs will illuminate, and the bottom LED will be red. You will also hear a single audible beep.

5. Turn on the Nursery Unit using the On/Off switch on the side. The green power light should come on.

6. Within a few seconds, the Parent Unit will lock on to the Nursery Unit and the top four (4) green LEDs will shut off. A second later, you will hear a series of beeps and the connection LED should change from red to green. Your monitor is now ready for use.

7. If the top four (4) LEDs do not shut off, power off the Parent Unit and the Nursery Unit and repeat steps 4 and 5 above.

8. If the connection LED on the Parent Unit does not change from red to green and the unit begins to beep, press the channel “ch” button on the Nurser the connection LED should change from red to green. Y

9. If the Parent Unit is still unable to lock in on the Nurser both the Parent Unit and the Nurser pressing the On/Off switch. When the unit powers up, you will hear a single beep and all of the soundlights will illuminate. Release the volume down switch and within 2 seconds you will hear two beeps and all of the Sound Light LEDs will stay lit and the bottom LED will be red.

10. Repeat steps 5 & 6 above. Repeat same set-up procedure if your system has two Parent Units.

y Unit. Within a few seconds, the Parent Unit should lock in on the Nursery Unit and

ou may hear an audible beep during this process.

y Unit (connection LED will be red and the unit will beep), power down

y Unit. W

ait for 10 seconds then hold the volume down button on the Parent Unit while

+ 8 hidden pages