This
manual
WWARNINOS
READ
AND
contains
and
RETAIN FOR REFERENCE
IMPORTANT
INSTRUCTIONS
MODEL
2
150
psi
2250psi
800-048
(150
SERIES
"A"
bar) OPERATING PRESSURE
(155 bar) MAXIMUM WORKING PRESSURE
~NJECTOQIM
Fluids under high pressure from spray or leaks can
penetrate the skin and cause extremely serious
injury, including the need for amputation.
NEVER
the body.
NEVER
NEVER
body.
point the spray gun
put hand or fingers over the spray tip.
try to stop or deflect leaks with your hand or
ALWAYS
MEDlCAU
HAZARD
at
anyone or any part of
have the tip guard in place when spraying.
TREATMENT
Do
not use chemicals or agents which are not
compatible with Buna-N and
of hose.
Do
not leave a pressurized unit unattended. Shut off
the unit and release pressure before leaving.
PVC
or neoprene cover
FORE
Do
not spray flammable liquids.
engine where combustible fumes or dust may be
present.
Do
not operate the
GENERAL
NEVER
Keep clear of moving parts when the unit is running.
run the unit with the belt guard removed.
If
any fluid appears to penetrate your skin. get
EMERGENCY
DO
MOK
Tell the doctor exactly what fluid was injected. For
treatment instructions have your doctor call the
RIAJIORIAU
MEDKAL
TREAT
POISON
CARE
AS
A
SIMPLE
CENTER
AB
ONCE.
GUT.
NETWORK
($a2w~-666~
AVOID
Even after you shut off the gasoline engine, there is
high pressure in the pump, hose and gun until you
release
the spray tip or servicing the unit,
unit
Be sure that all accessory items and system
components
NEVER
in
personal safety, as well as the function of the
equipment, is at stake.
Before each use, check hose for weak, worn or
damaged conditions caused by traffic, sharp corners,
pinching or kinking. Tighten all fluid connections
securely before each use. Replace any damaged
hose.
COMPONENT
it
by triggering the gun.
and
trigger the gun to release pressure.
will
withstand the pressure developed.
exceed the pressure rating of any component
system.
NEVER
alter or modify equipment -your
RUPTURE
So
before removing
always
shut off the
Observe detergent manufacturer's safety
precautions. Avoid getting detergent or other liquids
in your eyes. Follow the directions on the container
regarding contact with eyes, nose, and skin,
breathing fumes, etc. Always wear full goggles to
protect your eyes from the spray
dislodged by the spray. If necessary, wear gloves or
other protective clothing. If antidotes or treatment
are 'recommended, be prepared to use them.
DON'T
weed killer.
This unit is supplied with an 8-foot power cord made
up
electric cord is connected to the unit chassis and
motor frame. The other three wires are connected to
the starter switch.
Be sure to connect the power cord
approved plug to
The starter switch has a built-in circuit breaker that
will shut off the power to the unit whenever the
circuit
Always check to be sure the switch
hoses and electric cord are clear
before plugging in the power cord.
spray toxic chemicals such as insecticide or
of
three AWG No.
is
overloaded.
10
wires. The green wire of the
fit
your requirements.
as
well
as
any debris
to
the appropriate
is
off andthat the
of
moving parts
IMPORTANT
United States Government safety standards have been adopted under the Occupational Safety and Health Act.
These standards
Should be consulted
2
801-457
. . .
.
. .
-
particularly the General Standards, Part 1910. and the Construction Standards,Part 1926
in
connection with your use of airless spray equipment.
.
.
.
.
._i..
. . . ~.
. . . .. . ..
.
.-
.~.
.
..
:
..
~
..
-
INSTALLATION
Check Electrical Service and Plug
in
Before plugging
service is 1 phase 220
ON-OFF switch
supply cord into
extension cord,
gauge (2.5
m) long.
Install
Slide the axle through the frame. Slide the wheels
and washers onto the axle and secure
cotter pins provided. Install the hub caps. Attach the
handle
washers and nuts provided.
l,nstall
Connect the spray hose to the spray gun by inserting
the pin at the end of the hose into the quick
disconnect coupler on the gun. Connect the hose to
the fluid outlet
Remove the tape from the cap on top of the pump.
-
..
.
$.
Cleaning Accessories
'..
i
For spraying detergent or other cleaning solution, we
recommend
'
Accessories
installation and operation.
mm2)
Wheels and Handle
with
Hose
the sprayer, be sure the electrical
V,
60
HAC,
in
the OFF position, plug the power
a
grounded outlet. If you use an
it
must have 3 wires of at least 10
and should not be over
the four screws, flat washers, lock
and Spray
in
using
and instruction manual 801-192 for
Gun
the same way.
a
chemical injector kit. See
In
30
Amp. WitKthe
100
in
place
ft
(30.3
with
For removing rust andold paint we recommend using
a water sandblaster.
manual 801.190 for installation and operation.
To
Connect
Water Supply
See
Accessoriesand instruction
CAUTION
Before attaching to water supply. check local
plumbing code regarding cross-connection to
water supply. Backflow check valve 801-133.
Do
not exceed 1 6OoF (7OOC) water temperature to
in
a
pump
Connect a hose with at least a 3/4 in. (19 mm)
from your city water supply to the unit's
garden hose threaded inlet. The supply hose should
not be more than
NOTE:
If your operating conditions are different from above.
contact our Customer Service Department for
assistance.
direct supply system.
3/4
in.
50
ft.
(15
m) long.
For a direct supply system, your water
source at the
AT LEAST 5 GPM
unit
must
have a flow rate of
(19
LITER/MINI.
ID
OPERATION
CAUTION
Startup
Before starting, be sure to read the safety warnings
and setup instructions.
Turn on the water supply.
Trigger the gun to release any back pressure.
1..
CAUTION
Never run the cleaning unit dry. Costlydamage
to the pump will result. Always be sure water
supplyiscompletelyturnedonbeforeoperating.
Inspect all connections for any leaks. Tighten if
necessary.
Cleaning
For cleaning technique, see the Chemical lniector
manual,
For abrasive cleaning, see the Water Sandblaster
manual,
801
801
-1
-1
92.
90.
spraying. for longer pump life. The pump
overheat if left running for over
in
Check the filter screen
as often as necessary, at least daily.
the unit with the inlet and filter screen removed.
DONOTtrytoadjusttheunloadervalveorchangethe
engine speed. Changing these settings may cause
excessive pressure, intermittent unloader operation,
wastedfuelandincreasedwearonpartsandwillvoid
the warranty.
PUMP MUST NOT BE RUN
of
water prior to exposure to freezing temperatures.
Use and store the unit where it
to freezing temperatures.
unit, thaw before trying to start. A
solution may be pumped prior to cold weather
storage.
Use only spray tips that are matched to the unit to
avoid excessive cycling and wear of the unloader
valve. See Accessories.
the water inlet connection
DRY
If
water does freeze
10
Do
and must bedrained
will
not be subjected
50%
will
minutes
not operate
in
the
anti-freeze
Follow these precautions when removing and
installing nozzles:
1.
Shut off the cleaning unit and trigger thegun
to relieve pressure. Engage the trigger safety.
2.
Keep the nozzle a.nd the tube pointed away
from you and everyone else.
3.
Do
not put your hand over the tip
nozzle into place. Grasp
keep your fingers away from the tip.
4.
Do
not let anyone else touch the spray'valve
while you are cleaning nozzles.
5.
Be
sure the slip ring
the nozzle in place beforetriggering thespray
gun.
.
Shutdown and
When unit is not
When shutting down for the day or weekend,
unit, shut off water supply valve, and trigger gun to
release pressure. Wipe off the unit with
Care
Of
in
use, turn off water supply.
it
is
pushedforward to lock
Unit
to
push the
from the side and
shut
a
damp rag.
off
pour hot water on a frozen pump. A sudden
temperature change may crack the ceramic
plungers.
Do
not pump caustic materials.
Before extended storage, flush the pump with light
oil.
Avoiddragginghoseoveranabrasivesurfacesuchas
cement. This causes excessive wear and shorter
hose life.
Clean the intake line strainer daily
Lubrication and Care
Fill pump crankcase to dot on oil gauge window with
25
02.
(0.75
liters)
of
crankcase
or equivalent SAE
antiwear and rust inhibitor additives. Change initial
fill after
months or at
50
hour running period. Change oil every
500
40
hour intervals.
oil
(part
no.
weight hydraulic oil
801
-1
44)'
with
3
WARMING
I
NEVER
valve.
alter adiustment or modifv the unloader
1
I
Altering or adjusting unloader willnot increase
performance of unit.
I
4
..
801-457
. .
...
,
.
.. . .
.
.
._ . .
. .
.
. . ...
.
..
.. ~ . .
..
. .
.. .. . ..
I.
.
.
PROBLEM
CAUSE
SOLUTION
Low pressure.
Pump runs extremely rough,
uressure low.
Worn nozzle.
Belt slippage.
in
Air leak
Relief valve stuck, partially
plugged or improperly adjusted
valve seat worn.
Inlet suction strainer clogged
improper size.
Worn packing. Abrasives in
pumped fluid or severe cavitation. Inadequate water supply.
Fouled or dim/ inlet or discharge
valves.
Worn inlet or discharge valves.
Leaky discharge hose.
Restricted inlet or air entering
the inlet plumbing.
inlet plumbing.
Replace
Tighten or replace; use correct belts and replac
both at same time.
Disassemble, reseal, and reassemble.
Clean. and adjust relief valve; check for worn
and dirty valve seats. Kit available.
Clean.
o
frequently.
Install proper filter. Check flow available to
pump.
Clean inlet and discharge valve assemblies.
Replace worn valves, valve seats and/or
discharge hose.
Proper size inlet plumbing; check for airtight
seal.
with
nozzle of proper size.
Use
adequate size. Check more
Water leakage from under
the manifold.
Water in pump crankcase.
Frequent or premature
failure of the packing.
Inlet restrictions and/or air
leaks. Stuck inlet or discharge
valve.
Leaking
Worn packing.
May
condensing into water inside the
crankcase.
Scored plungers.
Over pressure to inlet manifold
Damaged or worn plungers.
Abrasive material
being pumped.
Excessive pressure and/or tern
perature of fluid being pumped.
Over pressure of pumps.
H.P.
seals.
be caused by humid air
in
the fluid
Clean out foreign material, replace worn valve:
Replace seals.
Install new packing.
Change oil at
using Graco Crankcase
every month or
?eplace plungers.
?educe inlet pressure.
3eplace plungers.
nstall proper filtration on pump inlet plumbing
:heck pressures and fluid inlet temperature; bc
jure they are within specified range.
?educe pressure.
3
month or
200
500
Oil
(other approved
hours)
P.N.
hour interval
801-144.
o
Strong surging at the inlet
3nd low pressure on the
jischarge side.
Running pump dry.
Foreign particles
discharge valve, or worn inlet
and/or discharge valves.
in
the inlet or
10
not run pump without water.
:heck for smooth lap surfaces on inlet and
iischarge valve seats. Discharge valve seats
md inlet valve seats may be lapped on
ine oil stone.
a
very
building circuit fuse blown.
SOLUTION
Check, replace.
Electric motor stops while
spraying.
Electric motor runs,
no output.
'This
unit
has an overload breaker built into the switch assembly. If
cool for
needed.
NOTE:
PUMP
30
to
60
A
M11
required for servicing pump.
but
minutes. Also, try to correct the cause of overheating. Always use the lowest pressure setting
and
Overload switch has opened.
Power cord unplugged, or
building circuit fuse blown.
Overload breaker.has opened.
Extension cord
Tip plugged.
Displacement pump frozen or
gear train damage.
M30
metric wrenches are
Unplug power cord'. decrease pressure
~ ~~~
Check, replace.
Unplug powei cord'. relieve pressure-allow
to cool.
DonZ use more than
Remove and clean
Thaw,
it
opens, unplug power cord and let sprayer
loOftoi
8
ga extension cord.
Valves
Photo 1 and
1)
Remove the hex plug using an
2)
Examine O-ring under plug and replace
evidence of cuts or distortion.
3)
Remove valve assembly including, retainer.
spring, valve and valve seat from valve cavity.
MOTE:
41
Replace valve parts
including retainer, spring, valve, valve seat,
ring and back-up-ring.
5)
Replace valve cover and torque to
2.
M30
Valve assembly may come apart during
removal.
with
service kit
75
Nm).
Pumping
Photo
1)
2)
I
3)
Section
3.
Remove the four
Separate the manifold from the crankcase.
NOTE:
Keep manifold properlyaligned with ceramic
plungers when removing to avoid damage to
either Dlunclers or seals.
Carefully examine each plunger for any scoring
and replace if necessary.
It may be necessary to tap manifold
lightly with mallet to loosen.
{4)
hex nuts from the manifold.
~ ~~
1
wrench.
(801-041)
ft-lb
(100
~~ ~
if
o-
6
..
801-457
....
~
..
......
...
~ ..
Plungers
Photo
4.
1)Using .an
M1
1
wrench,
remove the plunger retainer.
2)
Slide out the seal retainer with
oil wick and rubber barrier
slinger.
3).
With a slight twisting motion,
loosen the plunger from the
plunger rod and remove.
MOTE:
The stud may remain
with the retainer
when removed.
Disassemble and
screw stud into
plunger rod finger
tight.
4)
Replace O-ring and back up
ring on plunger retainer.
5)
Saturate new oil wick by
in
soaking
6)
Install new plunger.
7)
Replace plunger retainer and
torque to
8)
Install new oil wick in seal
oil.
80
in-lb
(9
Nm).
retainer.
9)
Replace barrier slinger over
new plunger.
10) Lubricate each plunger sleeve
and carefully slide manifold
onto crankcase.
Seals or V-Packings
Photo
5,
6,
7
and
8.
1) Remove C-ring from seal case.
2)
Then remove the low pressure
seal from the seal case.
3)
Unscrew the seal case from
the manifold using a special
key wrench (801
4)
Remove the high pressure
-044).
seal and examine. Before'
replacing, lubricate
ID
and
OD
of new high-pressure seal and
press into manifold.
NOTE:
A
socket and extension may be used to
pressure seal from
manifold.
5)
Install
new O-ring on seal case
and lubricate OD of O-ring.
6)
Screw seal case into manifold.
7)
Lubricate
ID
and
OD
of low
pressure seal and press into
seal case.
8)
Replace C-ring holding
pressure seal in place.
..
~.
..
..~ - . , ..
.,
low
,...
9)
Lubricate each plunger sleeve
and carefully slide manifold
onto crankcase.
NOTE:
When replacing
manifold onto plungers,
enreme caution should
be
exercised to avoid
damage to the seals.
.
~..
.
. . . ..
_.
.
10)
Torqueallfour(4)bltsto240ir-lb
(27
Nm).
NOTE:
Carefully study the
order of respective
parts and note
position of seals to
assure proper reassembly and opera-
tion.
801-457
..
..
.
7
"
. .
.
. . .
.,
8
801-457
-
..,
"..
.
...
~,
~.
~
.
.
.
..
..
.
.
-~
..
.
..
..
.
.
Ref.
No.
50
Includes items
51-66, 79 & 81
62
fj/7g
63
52
64
65
REF
66
56
59
PARTS
REF
NO.
1
2 801-001
3 800-015
4 800-038
5 800-047
6 801-390
8
9 801-231
10 801-140
11
12 801-022
13 801-131
14 801-221
15 801.394
16 801-379
17 801-448
18 801-446
19 801-292
20 800-039
21 801-088
.’
..
22
23
LIST
PART
NO.
801-285
801-129
801-298
801-302
.DESCRIPTION CITY
HOSE
&
detail for parts
PUMP, REPLACEMENT PARTS,
include items
ANTI VIBRATION FOOT
CHASSIS
ELECTRIC MOTOR ASSY
BRACKET. spacer
BELT. drive
LABEL. warning
LABEL, identification
LABEL. warning
.SCREW, machine, hex hd..
5/16-18
PLATE, serial
CONNECTOR, crimp
HANDLE
SWITCH, starter
CORD. power
STRAIN RELIEF
SCREW, self tapping.
no.
RAIL STIFFNER ASSY
SCREW, machine, hex hd,
5/16-18
SCREW, machine. hex hd.
5/16-18
SCREW, machine hex tid,
5/16-18
GUN ASSY. see gun
77-90
NC
x
1-3/4”
no.
(8
6-32
NC
x
1/2 2
NCx
1-1/2” 4
NC
x
2-1/2”
NCx
1”
ft
Ig)
2
2
2
1
1
4
1
2
1
1
1
2
1
1
4
8
1
1
1
1
1
NO.
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
PART
NO.
801 -082
801-081
801 -023
801
-01 5
801
-1
39
801 -025
801 -024
801 -01 2
801 -367
801.241
801 -004
801-381
801-135
801
-1
37
801 -393
801 -235
801 -01
801 -364
801.365
801 -242
801 -243
801-132
801-130
801 -388
801-141
801 -41 7
800-045
801 -045
801 -046
801 -047
801 -048
801 -049
801 -050
801 -046
801 -059
801 -41 2
801-432
801 -062
801
-063
801 -068
801-069
801 -070
801-071
801 -090
801-105
801-106
801 -41 6
801-108
801-109
801-110
801
-1
11
801-112
801-113
801 -445
801 -450
800-044
801
-008
801 -465
DESCRIPTION
SCREW, machine. hex hd,
..6 x 30
r!A
CREW. machine, hex hd.
S
MB
WASHER.
WASHER. flat,
WASHER, lock,
WASHER. lock,
NUT, hex.
GROMMET
BUMPER
WHEEL
PULLEY, pump
PULLEY, motor
HUE. pulley
KEY, pulley
AXLE
WASHER,
8
BRACKET, tensioner
BELTGUARD. cover
BELTGUARD. baseplate
HUBCAP
PIN, cotter
RIVET, drive
LABEL, warning
LABEL. warning
LABEL. warning
LABEL, starting
UNLOADER, includes
items
CAGE, valve
O-RING
SPRING
BALL
SEAT
.
O-RING
UNLOADER SUE-ASSY.
n.m~G
HOUSSG
CYLINDER
O-RING
PLUG
HOUSING VALVE
SPRING
VALVE
SEAT
COUPLER, male quick disconnect.
NIPPLE, straight. brass,
1 /2
TEE, brass,
NIPPLE, hex, steel,
NIPPLE, hex, brass,
PLUG. hex. brass.
ADAPTER,
NUT. brass, adapter
SCREEN, inlet
HOSE, coupled,
17-1 /2”
LABEL. caution
O-RING
SLEEVE ASSY
LABEL
SCREW, button hd,
#6-32
mm
x
20
mm
flat.
1/4
5/16
1 /4
5/16
5/16-18
(2”
lg)
flat
51-66. 79. 81
~~
.
NPT
x
3-1 /2” 1
1/2
NPT
1/2
1/4 x 1/2
3/8
.~ ~
1
/2
hose
1
/2
5/16
NC
lg
x
NC
NPT
x
3/8
NPT
(MBE)
NPT
NPT
QTY
4
2
8
18
4
12
9
4
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
..
801-457
. . .
. . .
.
..
. . .
9
.
..
.
PARTS LIST
REF PART D.ESCRlPTlON
NO.
NO.
Items
77
~nl-nn
".
?E
801.028
79 801-267
80
801-030
81 801-031
82
801-032
83 801-033
84 801-034
85
801-035
86 801-036
87 801-037
88 801-038
89 801-039
90 801-040
Order parrs by name and number. Always give the model
number andseries letter
ordering.
(continued)
77-90
See exploded view of pump for details.
are pump internal replacement parts.
".
CAP
.
_.
..
.
O-RING,
.
DISCHARGE
MANIFOLD
.
WASHER
.
SEAL
.
RETAINER
.
WASHER
~
WICK
.
.
RING, retaining
.
PLUNGER
.
STUD
.
RING, backup
.
O-RING
.
RETAINER, plunger
cap
.
of
the assembly for which you are
QTY
ELECTRICAL SCHEMATIC
1
1
1
3
3
3
3
3
3
3
3
3
3
3
801-042
INCLUDES
-r
OF
PARTS
SEAL KIT
3
SETS
90
77.
-86
SERVICE
KEY
.
. - .
EXTRACTOR
TOOLS
WRFNCH
. . . .
-.
-
-
Rnl-nAA
.
.
-
- . -
TOOL
801-205
.
.
10
..
..
.
.....
801-457
. , .
~
.. .
.
. . . . .
-.
,
.
..
......
~. ~ ..
.
.
..
..
..
..
.
..
~..~
ij
Repair
Includes items
Kit
801
-083
A,
B.
C,
D,
E
and
F
/A)
k21
SERVICE
1.
Pressaccesspin(17)fromgunhandleandremove
access plate
handle. Unscrew both short and long tubes with
fittings (12 and
body should now slide out
the access plate opening.
2. Remove the cap (14). spring
the valve body
3.
Remove the snap ring
seat
(C)
4.
Remove the sleeve nut
actuator rod
5.
."
...
.
.
.
..
_.
Afterinstallingthenewseat(C)andball(A),tapthe
ball lightly
seating between the ball and seat.
6.
Reassemble
pipe threads on both short and long tubes(l2 and
151.
(4)
by sliding plate towards back
15)
(10).
and O-ring
(F).
with
in
reverse order. Use pipe sealant on
from
valve body
of
(5)
(e).
Then remove the valve
(13).
(1 1)
and O-ring
a
hammer to assure a proper
))
L
(10);
Valve
the handle through
and ball
(E)
(A)
with
from
the
of
@
PARTS LIST
RE
:F
PART
).
NO. DESCRIPTION
N<
801
800-043
5
6
7
8
9
10
11
12
13
801-250
14
15
16
17
..
18
19
20
21
'801 -090
22
23
801 -073
'801 -01
24
25
"801 -01 1
26
801 -074
801-103
27
*a01
28
Order parts by name
which
you
*Recommended
-007
-091
are
.
.
.
.
TUBE,
GRIP
COUPLER,
COUPLER,
HOUSING,
0
TIP,
TIP,
GUARD,
NIPPLE,
COUPLER,
ordering.
"tool
SPRAY HOSE,
(1
5
m)
IQ
SPRAY GUN,
include
HANDLE
ACCESS PLATE
SPRING
TRIGGER
.
NEEDLE
.
HEX
PLUG
.
DISCHARGE FllTlNG
.
VALVE BODY
.
GUIDE SLEEVE
.
TUBE
.
INLET FllTlNG
.
CAP
SAFETY LATCH
ACCESS PIN
LATCH PIN
32"
blasting;
cleaning;
and
box" spare
3/8"
(replaceable
items
3-18)
female quick disconnect
male
quick disconnect
nozzle
0"
150
tip
hex; 1/4 x 3/8"
male quick disconnect
series
letter
parts.
ID,
50
ft.
parts
npt;
brass
of
the assembly
801.457
an
1
1
1
1
1
1
1
1
1
1
1
1
1
for
11
ACCESSORIES
(Must
be
purchased
separately)
CHECK VALVE
801
-1
33
CHEMICAL INJECTOR
KIT
800-102
Prevent back up of contaminated water into fresh For injecting harsh cleaning chemicals downstream
supply. Install upstream from pump.
WATER SANDBLASTER 800-1
03
from pump.
ADJUSTABLE SAND SAVER 801-031
For abrasive cleaning of stubborn dirt and paint. For adjusting sand flow.
TECHNICAL DATA
MOTOR: 5 hp, 1 phase
220 V.
WATER PUMP: 2150 PSI (150 bar) max
pressure;
(15 liter/min).
WETTED PARTS: Stainless Steel, Aluminum,
Phenolic Plastic, Ceramic
Liners, Nitrile Rubber.
WEIGHT: 195 Ibs
OVERALL DIMENSION: Length:
Width: 27
Height: 26
60
Hz, 27.5 Amp
4
G,PM
(88
kg)
38
in
(965 mm)
in
(686 mm)
in
(660
mm)
MAX. WATER TEMPERATURE: 1 6OoF
INLET HOSE CONNECTION: 3/4-in. garden hose
THE
GRACO
GracoInc.warrantsallequipmentmanufacturedbyitandbear~ngitsnametobefreeframdefectsin
material and workmanship under normal use and service. This warranty extends to the original
purchaserforaperiodof12monthsfromthedateofpurchaseandappliesanlywhentheequipment
is installed and operated in accordance with
not
cover damage
abrasion. corrosion. negligence, accident. substitution of non-Graco parts. faulty installation
tampering.
This warranty is conditioned upon the prepaid return of the equipment clatmed
examination by Graco toverify the claimeddefect. If the claimed defect is verified. Graco will repair
or
replace free
purchaser transportation prepaid. If inspection
workmanship
be charged.
EOUIPMENT NOT COVERED
sold bv Graco that
subject
to
assistance in making such
the warranty.
or
wear which.
of
charge. any defective parts. The equipment will be returned
or
material, repairs will be madeata reasonablechargeandreturntranspartation will
PURPOSE AND
..............
are
not
manufactured byGraco(such aselectric motors. switches. hose.etc.)are
if
any.
claims.
in
the reasonable judgment
OF
ANY NON-CONTR
BY
GRACO WARRANTY. Accessories
of
their manufacturer. Graco will provide purchaser wcth reasonable
WARRANTY
writtenfactaryrecommendations.This
of
the equipment does
(70°C)
of
or
(f)
Graco. arises
to
not
disclose any defect
components
warrantydoes
from
misuse.
or
be defective for
IO
the original
of
equipment
in
Subsidiary and Affiliate Companies:
Factory
GRACO
.
.~
.
INC.
Branches:
P.Q.
-
..
PRINTED
Atlanta. Pallas, Detroit,
Canada: England; Switzerland;
BOX
1441
IN
U.S.A.
........
MORIRIEAPQLIS,
801.457
Lo6
Angeles.
West
France;
Caldweli
Germany;
MRI
Rev A
7/83
..........
1N.J.l
Hong
55440-1444
Kong: Japan
45-10051A
.....
."
.....
Loading...