Graco Hydra-Clean 826, Hydra-Clean 1235 800-268, Hydra-Clean 826 800-093 Instructions-parts List Manual

INSTRUCTIONS-PARTS LIST

This manual contains IMPORTANT
WARNINGS and INSTRUCTIONS

READ AND RETAIN FOR REFERENCE

HYDRA-CLEAN @ 826,1235
Pressure Washers

HYDRA-CLEAN 826
Model 800-093, Series B

800 psi (55 bar) OPERATING PRESSURE

1100 psi (76 bar) MAXIMUM WORKING PRESSURE

HYDRA-CLEAN 1235

Model 800-268, Series A

7200 psi (83 bar) OPERATING PRESSURE
1500 psi (103 bar) MAX/MUM WORKING PRESSURE

‘3

0

ORAICO

308-518

Rev

A

Supersedes 801-888

GRACO INC. P.O. Box 1441 MINNEAPOLIS, MN 55440-1441

@COPYRIGHT 1990, GRACO INC.

WARNING

HIGH PRESSURE SPRAY CAN CAUSE SERIOUS INJURY.

FOR PROFESSIONAL USE ONLY OBSERVE ALL WARNINGS.

Read and understand all instruction manuals before operating equipment.

FLUID INJECTION HAZARD

General Safety

This pressure washer generates very high fluid
pressure. Spray from the gun, leaks or ruptured
components can inject fluid through your skin and into
your body and cause extremely serious bodily injury

including the need for amputation. Also, fluid injected or
splashed into the eyes or on the skin can cause serious
damage.

NEVER point the spray gun or wand at anyone or at any
part of the body. NEVER put hand or fingers over the
spray tip.

ALWAYS follow the

Pressure Relief Procedure,

before

cleaning or servicing any part of the sprayer.

NEVER try to stop or deflect leaks with your hand or

body.
Be sure equipment safety devices are operating

properly before each use.

Medical Treatment

If any fluid appears to penetrate your skin, get

EMERGENCY MEDICALTREATMENTATONCE. DO
NOT TREAT AS A SIMPLE CUT.

Tell the doctor exactly

what fluid was injected.

NOTE TO PHYSICIAN:

Injection in the skin is a

traumatic injury

It is important to treat the injury

surgically as soon as possible. Do

not delay
treatment to research toxicity. Toxicity is a
concern with some exotic coatings injected
directly into the bloodstream. Consultation with a

plastic

surgeon or reconstructive hand surgeon

may be advisable.

Pressure

Relief Procedure

To reduce the risk of serious bodily injury, including fluid

injection and splashing in the eyes, or on the skin,
always follow this procedure whenever you stop
spraying for more than 10 minutes, when shutting down,
and before checking or repairing any part of the system.

1.

Engage the trigger safety latch.

2.

Turn the sprayer off.

3.

Disconnect the electrical supply.

4.

Shut off the water supply.

5.

Disengage the trigger safety latch and trigger the
gun to relieve pressure, and then engage the trigger
safety latch again.

6. Before long-term (overnight) storage, disconnect

the water supply and disconnect the electricity.

Spray Gun Safety Devices

Be sure all gun safety devices are operating properly
before each use. Do not remove or modify any part of
the gun; this can cause a malfunction and result in
serious bodily injury.

SAFETY LATCH: Whenever you stop spraying for a
moment, always set the gun safety latch in the engaged
or “safe” position, making the gun inoperative. Failure to
properly set the safety latch can result in accidental

triggering of the gun.
SPRAY TIP SAFETY: Use extreme caution when

cleaning or changing spray tips. If a spray tip clogs
while spraying, engage the gun safety latch
immediately. ALWAYS follow the

Pressure Relief

Procedure

and then remove the spray tip to clean it.

GROUNDING INSTRUCTIONS

This product must be grounded. If it should malfunction
or break down, grounding provides a path of least
resistance for electric current to reduce the risk of
electric shock. This equipment is equipped with a cord
having an equipment-grounding conductor and a

grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and
grounded in accordance with all local codes and
ordinances.

DANGER

Improper connection of the equipment- grounding
conductor can result in the risk of electrocution.
Check with a qualified electrician or service
person if you are in doubt as to whether the outlet
is properly grounded. Do not modify the plug
provided with the product - if it will not fit the outlet,
have a proper outlet installed by a qualified
electrician.

2

308-518

GROUND FAULT CIRCUIT INTERRUPTER PROTECTION (826)

The 826 pressure washer is provided with a

ground-fault circuit-interrupter (GFCI) built into the
power supply cord. This device provides additional
protection from the risk of electric shock. Should
replacement of the cord become necessary, use only
identical replacement parts that include GFCI
protection.

CAUTION

DO NOT use the switch on the GFCI cord to start
the unit. This may cause premature failure of the

GFCI. ALWAYS turn the machine off at the switch
before resetting the GFCI.

GROUND FAULT CIRCUIT INTERRUPTER PROTECTION (1235)

To comply with the National Electrical Code (NFPA 70)
and to provide additional protection from the risk of
electric shock, connect the 1235 pressure washer to a

receptacle that is protected by a ground-fault
circuit-interrupter (GFCI).

EXTENSION CORDS

Use only 3-wire extension cords that have 3-prong
grounding-type plugs and 3-pole cord connectors that
accept the plug from the product. Use only extension
cords that are intended for outdoor use. These
extension cords are identified by a marking “Acceptable

for use with outdoor appliances; store indoors while not

in use.” Use only extension cords having an electrical
rating not less than the rating of the product. Do not use
damaged extension cords. Examine extension cord
before using and replace if damaged. Do not abuse
extension cord and do not yank or pull on any cord to

disconnect. Keep cord away from heat and sharp
edges. Always disconnect the extension cord from the
receptacle before disconnecting the product from the
extension cord.

To reduce the risk of electrocution, keep all

/,,,,,,,,,.,^‘“lNG _?

connections dry and off the ground. Do not touch

EQUIPMENT MISUSE HAZARD
General Safety

System Pressure

Any misuse of the pressure washer or accessories,

This sprayer can develop high operating pressure. Be

such as overpressurizing, modifying parts, using

sure that all spray equipment and accessories are rated

incompatible chemicals and fluids, or using worn or

to withstand the maximum working pressure of this

damaged parts, can cause them to rupture and result in

sprayer. DO NOT exceed the maximum working

fluid injection, splashing in the eyes or on the skin, or

pressure of any component or accessory used in the

other serious bodily injury, fire, explosion or property

system.

damage.

Chemical Compatibility

NEVER alter or modify any part of this equipment; doing

so could cause it to malfunction.
CHECK all spray equipment regularly and repair or

replace worn or damaged pans immediately.

BE SURE that

ail

chemicals used in the chemical

injector are compatible with the wetted parts of the

hose, gun, wand and tip, as given in the Technical Data

(page 22). Always read the chemical manufacturer’s
literature before using any chemical in this pressure

washer.

ALWAYS wear protective eyewear and appropriate

clothing. If using a chemical injector, read and follow

the chemical

manufacturer’s literature for
recommendations on additional protective equipment,
such as a respirator.

308-518 3

High pressure fluid in the hoses can be very dangerous.
If the hose develops a leak, split or rupture due to any
kind of wear, damage or misuse, the high pressure
spray emitted from it can cause a fluid injection injury or
other serious bodily injury or property damage.

ALL FLU/D HOSES MUST HAVE STRAIN RELEFS ON

BOTH ENDS. The strain reliefs help protect the hose
from kinks or bends at or close to the coupling, which
can result in hose rupture.

TlGHTEN all fluid connections securely before each
use. High pressure fluid can dislodge a loose coupling
or allow high pressure spray to be emitted from the
coupling.

NEVER use a damaged hose. Before each use, check
entire hose for cuts, leaks, abrasion, bulging cover, or
damage or movement of the hose couplings. If any of
these conditions exist, replace the hose immediately.
DO NO7 try to recouple high pressure hose or mend it
with tape or any other device. A repaired hose cannot

contain the high pressure fluid.

HANDLE AND ROUTEHOSES CAREFULLY

Do not pull
on hoses to move the pressure washer. Do not use
chemicals which are not compatible with the inner tube
and cover of the hose. DO NOT expose Grace hose to

temperatures above 200” F (93” C) or below -4W F

(-40” C).

Moving parts can pinch or amputate fingers or other

body parts. KEEP CLEAR of moving parts when starting

or operating the pressure washer.

NEVER operate the pressure washer without all guards

and interlocks installed and functioning. Follow the

Pressure Relief Procedure

before checking or

servicing the pressure washer to prevent discharging

high pressure fluid from the gun.

WARNING or DANGER:

Alerts user to avoid or correct

conditions that could cause bodily injury.

NOTE:

Identifies helpful procedures and information.

CAUTION:

Alerts user to avoid or correct conditions
that could cause damage to or destruction of
equipment.

IMPORTANT

United States Government safety standards have been adopted under the Occupational Safety and Health Act. These
standards -particularly the General Standards, Part 1910, and the Construction Standards, Pat-l 1926 -should be
consulted.

4

308-518

PUMP OIL LEVEL

INDICATOR

WINDOW

WATER

I

CONNECTION

-,-.. a-----.

MOTOR

SWITCH

/

ELECTRIC

PLUG

\

S/4” UAHDEN

HOSE (f)

INLET

FILTER PUMP

DIPSTICK

\

ADJUSTABLE
NOZZLE (826)

HIGH

SPRAY -

GUN

CONNECTION

QUICK

HIGH

PRESSURE \

SPRAY HOSE

Figure 1

Check for Shipping Damage

Check the unit for any damage that may have occurred

in shipping. Note any damage and

notify the carrier

immediately.

Set Up

Before plugging in the unit, be sure the electrical service
matches the specification in Technical Data (page 22 )
and the voltage label on the unit. With the unit off, plug
the power supply cord into a grounded, GFCI-protected
outlet. Do not remove the electrical plug which comes
with the unit or bend connecting prongs to fit an
improper outlet! Use an extension cord that meets the
requirements of the EXTENSlON CORD section and is
no more than 100 ft (30 m) long. Added length of cord
will affect current draw of unit.

If you are using a 1235 with a downstream chemical

injector, install it between the pump unloader and the
high pressure hose, using the quick couplers provided.

Connect the high pressure hose between the pump
outlet and the gun inlet.

Up to 100 ft (30 m) of high pressure hose may
performance, and chemical injector performance,

Install the appropriate spray tip on the wand of the 1235.
See Installing and Changing Spray Tips.

Connect to Water Supply

CAUTION

Before attaching to the water supply, check your
local plumbing code regarding cross- connection

to the water supply.
A backflow preventer P/N 801-l 33 is available to

prevent backflow of contaminated water into the
fresh water supply. Install it upstream from the

pump.
Install a regulating water valve, P/N 800-258, if

inlet water pressure is over 60 psi (4.1 bar).
Do not exceed 160” F (70” C) inlet water

temperature.

Connect a hose with at least a 314 inch (19 mm) ID and
not longer than 50 ft (15 m) to the unit’s 3/4 inch garden
hose inlet.

NOTE:

The water source at the unit musl have a
minimum flow rate equal to that of the unit (see
Technical Data, page 22).

308-518 5

Use this procedure whenever starting the pressure
washer to help insure that the unit is ready to operate
and starting is done safely.

1. Check the oil level.
Pump: Add SAE 20 or 30 weight non-detergent oil

as necessary.

2.

Turn on the water supply.

Never run the unit dry. Costly damage to the pump

c

will result. Always be sure the water supply IS
completely turned on before operating.

3.

4.

5.

6.

7.

Trigger the gun until water sprays from the tip
indicating that the air is purged from the system.

Plug the electrical cord into a proper, grounded,
GFCI-protected outlet.

ALWAYS engage the gun’s trigger safety latch
whenever you stop spraying, even for a moment to

reduce the risk of fluid injection or splashing in the
eyes or on the skin if the gun is bumped or triggered
accidentally.

Most pressure washer spraying is done at full
pressure. On this pressure washer there is an
adjustable unloader valve that permits operation at
less than maximum pressure. To reduce pressure,

for special cleaning applications, turn the pressure

control knob on the unloader counterclockwise, as
needed.

ALWAYS observe the followinq CAUTIONS to avoid

costly damage to the pressu‘;e washer.

CAUTION

DO NOTallow the pressure washer to idle for more
than 10 minutes. Doing so may cause the
recirculating water to overheat and seriously
damage the pump. Turn off the pressure washer if it
will not be spraying or cleaning at least every 10
minutes. If heated inlet water is used, reduce this
time further,

DO NOT run the pump dry, which will quickly
damage the pump. Be sure the water supply is
fully turned on before starting the pump.

DO NOToperate the pressure washer with the inlet
water screen removed. This screen helps keep
abrasive sediment out of the pump, which could
clog or scratch the pump. Keep this screen clean.

DO NOT pump caustic materials; such materials
may corrode the pump components.

Chemical Injector

BE SURE that all chemicals used in the chemical
injector are compatible with the wetted pans of the
hose, gun, wand and tip, as given in the Technical Data
(page 22). Always read the chemical manufacturer’s
literature before using any chemical in this pressure

washer.

~ri~RK!rZa”““‘.l

precautrons regarding use of goggles, protectrve

826: A downstream chemical injector is provided with
the pressure washer. Insert the chemical strainer
(attached with clear tubing to the chemical injector) into
the container of chemical. Turn the control ring on the
adjustable nozzle clockwise. This causes a drop in
pressure that actuates the chemical injector. Close the
adjustable nozzle to deactivate the chemical injector
and produce high pressure for rinsing. The flowrate of
the chemical is regulated by turning the chemical
adjustment knob on the injector. Maximum chemical
flow is at a full two turns counterclockwise from the
closed (clockwise) position.

1235: The chemical injector is an accessory. See the

chemical injector instruction manual.

WARNING

DO NOT attempt to open or close the adjustable

nozzle when the spray gun is in use. Be sure that

r

the trigger safety latch on the gun is in the “ON”
position before adjusting to avoid serious bodily

injury or fluid injection.

Check the distance that you will need to hold the spray
nozzle from the surface by test spraying on a scrap of
similar material. For soft surfaces, such as wood, hold
nozzle 3 ft (1 m) from the surface and gradually bring it
closer, checking to see if the high pressure spray is
damaging the surface.

Mist the wet surface with cleaning solution. Let it soak
briefly, then use the high pressure rinse to “chisel” off
the soil. Keep the nozzle at an angle to the surface and
at a distance determined to be best for the surface. If
some soil remains, repeat the procedure, letting the
chemical soak a little longer. Stubborn soil can be
cleaned off better with a stronger, heated cleaning
solution.

Protect surfaces that might be damaged by the cleaning
solution or the high pressure spray. Rinse the solution
before it dries.

8.

See the chemical injector or kit manual for detailed
cleaning information if this accessory is used.

6

308-518

Trigger Safety Latch

WARNING

To reduce the risk of serious bodily injury,

including fluid injection, splashing in the eyes or
on the skin, ALWAYS engage the trigger safety
latch whenever spraying stops, even for a
moment.

In the engaged position, the trigger safety latch
prevents the gun from being triggered accidentally
by hand or if it is dropped or bumped. Be sure the
latch is pushed fully down when engaging it or it
cannot prevent the gun from being triggered. See
Figure 2.

TRIGGER SAFETY ’

LATCH SHOWN

\

\:

ENGAGED

TRIGGER SAFETY

LATCH SHOWN

DISENGAGED

Figure 2

Installing and Changing Spray Tips (1235)

WARNING

To reduce the risk of serious bodily injury,

including fluid injection or splashing in the eyes or
onto the skin, use extreme caution when changing
spray tips. ALWAYS follow the procedure below.

1. Follow the

Pressure Relief Procedure.

2. Point the gun and wand away from yourself and
anyone else.

3. Without holding your hand over the spray tip (A),
pull back the quick coupler ring (B), remove the tip
and then release the ring. See Figure 3.

4. Be sure the tip is secure before starting to spray
again.

5. Tip holding holes are provided on the chassis.

Figure 3

308-518 7

SHUTDOWN, FLUSHING AND STORAGE

WARNING

Pressure Relief Procedure

To reduce the risk of serious bodily injury,

including fluid injection and splashing in the eyes,
or on the skin, always follow this procedure

whenever you stop spraying for more than 10

minutes, when shutting down, and before
checking or repairing any part of the system.

1.

2.

3.

4.

5.

6.

Engage the trigger safety latch.

Turn the sprayer off.

Disconnect the electrical supply.
Shut off the water supply.
Disengage the trigger safety latch and trigger

the gun to relieve pressure, and then engage

the trigger safety latch again.

Before long-term (overnight) storage,
disconnect the water supply and disconnect
the electricity.

1. If the pressure washer will be exposed to freezing
temperatures, drain all water out of the pump. If it
must be stored in freezing temperatures, flush the
unit with a 50% anti-freeze solution. Relieve
pressure. Flush the pressure washer before using it
again to remove the anti-freeze.

NOTE:

An anti-freeze flush kit P/N 802-327 is
available to make flushing easier.

CAUTION

If water does freeze in the pressure washer, thaw it
in a warm room before trying to start it. DO NOT
pour hot water on

or into the pump; it may crack the

ceramic plungers!

2. After each use, wipe all surfaces of the pressure
washer with a clean, damp cloth.

3. Perform the appropriate maintenance. See the
maintenance chart.

MAINTENANCE I___

Observing regular maintenance intervals helps ensure
that you get maximum performance and life from the
pressure washer.

There is a break-in period for the pump. After changing
the oil initially, the interval between required changes is
longer.

WARNING

To reduce the risk of serious bodily injury,

including fluid injection, splashing in the eyes or
on the skin or injury from moving pans, always
follow the

Pressure Relief Procedure Warning

before proceeding.

Interval

Daily

What to do

Clean water inlet screen and
filter. Check pump oil level. Fill
as necessary.

After first 50
hours of
operation

Change pump break-in oil. Use
SAE 20 or 30 non-detergent oil.

Each 500 hours

Change pump oil. Use SAE 20 or
of operation or 30 non-detergent oil.
6 months

8

308-518

TROUBLESHOOTING CHART

WARNING

To reduce the risk of serious bodily injury, including fluid injection, splashing in the eyes or on the skin, or injury from
moving parts, always follow the

Pressure Relief Procedure Warning

before proceeding.

I

8

Problem

Cause

Solution

-0w pressure and/or
,ump runs rough

Worn or wrong size tip,

Replace with tip of proper size.

Inlet filter clogged.

Clean. Check more frequently.

Worn packings, abrasives in water or
natural wear.

Check filter. Replace packings. See

PUMP SERVICE.

Inadequate water supply.

Check water flow rate to pump.
Coupling slippage. Tighten or replace.
Fouled or dirty inlet or discharge valves.

Even a small particle can cause the valve

Clean inlet and discharge valve assemblies. Check

filter.
to stick.

Restricted inlet.

Check garden hose, may be collapsed or kinked.
Worn inlet or discharge valves.

Replace worn valves.
Leaking high pressure hose.

Replace high pressure hose.

Nater leakage from
under pump manifold

Worn packings.

Install new packings. See PUMP SERVICE.

Nater in pump

Humid air condensing inside crankcase.

Change oil as specified in MAINTENANCE.
Worn packings.

Install new packings. See PUMP SERVICE.
Oil seals leaking.

Install new oil seals. See PUMP SERVICE.

?equent or
Iremature failure of

Scored, damaged or worn plungers.

Install new plungers. See PUMP SERVICE.

he packings

Abrasive material in the fluid being pumped.

Install proper filtration on pump inlet plumbing.

Inlet water temperature too high.

Check water temperature; may not exceed 160°F

Overpressurizing pump.

Do not modify any factory-set adjustments. See

EQUIPMENT MISUSE HAZARD.

Excessive pressure due to partially plugged
or damaged tip.

Clean or replace tip. See Installing and Changing Spray
Tips.

Pump funning too long without spraying. Never run pump more than 10 minutes without spraying
Running pump dry.

Do not run pump without water.

Strong surging at the

nlet and low pressure

Foreign particles in the inlet or discharge

Clean or replace valves. See PUMP SERVICE.

on the discharge side

valve or worn inlet and/or discharge valves.

Jnit will not start

Unit not plugged in.

Check power cord.

Electrical service off/GFCI activated.

Check fuse/circuit breaker. Check for proper

Thermal overload has tripped.

grounding.
Press reset button on motor.

Chemical injector will
lot siphon

Chemical injector clogged.

Disassemble chemical valve and clean. Check and
clean chemical hose and filter.

Adjustable nozzle completely closed (826).

Turn control ring on nozzle clockwise to cause drop in

pressure.

Low

chemical level.

Check level of chemical

Wrong tip (1235).

Install chemical tip.

308-518 9

To reduce the risk of serious bodily injury,
including fluid injection, splashing in the eyes or

NOTE:

The following metric wrenches are needed:

MlO, Ml3 and M30. Repair kits are available.
Refer to the individual repair sections and the
pump parts page for more details. For the best
results, use all parts in the kits.

NOTE: There are two different tool kits to aid in

servicing the pump. P/N 800-298 is used to
ease installation of packings. P/N 800-271
includes the items in 800-298 and tools to aid
in the removal of packing retainers.

Valves
NOTE:

For a set of six valves, order P/N 801-472.

1.

2.

3.

4.

Remove the hex plug from the manifold using an
M30 wrench.

Examine the o-ring under the hex plug and replace
it if it is cut or distorted.

Remove the valve assembly from the cavity; the
assembly may come apart.

Install the new valve. Install the o-ring and hex plug;
torque to 75 fl-lb (103 Nm).

NOTE: Retorque the plug after 5 hours of operation.

8.

Pumping Section

1. Remove the eight capscrews and Iockwashersfrom
the manifold using an Ml 3 wrench.

2. Carefully separate the manifold from the crankcase.

NOTE:

It may be necessary to tap the manifold lightly

with a soft mallet to loosen.

I CAUT’oN

Keep the manifold properly aligned with the

1

ceramic plungers when removing to avoid
damage to the plunger or seals.

3. Carefully examine each plunger for any scoring or

cracking and replace as necessary,

Servicing the Plungers

NOTE:

Plunger repair kit, P/N 801-474 is available to
replace retainers, o-rings, washers and
backup rings for three cylinders.

1.

2.

3.

4.

5.

6.

Loosen the plunger retaining screw five to six turns,
using an Ml 0 wrench. Push the plunger towards the
crankcase to separate the plunger and retaining
screw.

Remove the screw from the plunger and examine
the o-ring, backup ring and copper bearing/gasket
washer. Replace these parts if necessary using kit
801-474.

Remove the plunger and flinger from the plunger
shaft. Clean, examine and replace parts as
necessary.

Inspect the plunger shaft for oil leakage from the
crankcase. If leaking is obvious, replace the oil

seals. Otherwise, DO NOT remove these seals as
they cannot be reused. An oil seal kit is available to

replace the seals.

Lightly grease the oil seal, if it is being replaced,

and the flinger and replace them on the plunger

shaft. Then install the plunger.

Lightly grease the retaining screw and the outer end

of the plunger. Place the washer, o-ring and backup

ring around the screw and install the screw through
the plunger. Torque to 14.4 ft-lb (19.5 Nm).

7.

Servicing the V-Packings.

Lubricate the outside of each plunger. Slide the

manifold onto the crankcase, being careful not to

damage the seals.

Install the capscrews and washers finger-tight.

Torque the screws to 21.7ft-lb (29 Nm) following the

tightening pattern (Figure 4). Uneven tightening

may cause the manifold to bind or jam.

NOTE:

If you plan to replace the packings, refer to

Figure 4

1-O 308-518

Servicing the V-Packings

NOTE:

There are two types of packing kits: one is

just

packings, the other includes the packings,
rings and retainers.

5. Thoroughly clean the packing cavities and
examine.

6. Lightly grease the packing cavities and then
replace the packings in the following order: head
ring, v-packing, intermediate ring, head ring,
v-packing and packing retainer with the o-ring

installed in the retainer groove.

1.

2.

3.

4.

Remove the manifold as outlined in the Pumping
Section.

Carefully pull the packing retainer from the
manifold. Examine the o-ring and replace it if it is

cut or damaged.
Remove the v-packing and head ring. Pull out the

intermediate retainer ring. Remove the second

v-packing and second head ring.

Inspect all parts and replace as necessary.

7. Reassemble the manifold as instructed in Servicing
the Plungers.

308-518 11

800-093 Hydra-Clean@ 826 Pressure Washer

115 VOLT, 1 PHASE

-- ,.-

27

/

26

-- 32

WHT -I---

BLK
GRN

*

\yL-EL

MOTOR /

69 ~~

WIRING

BOX

T8

-

12 308-518

800-093 Hydra-Clean@ 826 Pressure Washer

REF
NO.

1
5
z

6
7

PART
NO.

801-683
803-059
801-881
801-901
801-023
801-025
801-940

801-900
803-486
801-905
801-907
801-865
801-880
801-890
801-891

i;

18
19
20
21

801-178
801-709
801-866
801-024
801-539
801-941

108-179
801-235
80 l-857
800-426

801-546

27

801-015

28 802-627

3’:
31

32

800-l 18
801-363
801-878
800- 175

33 801-541

DESCRIPTION

STRAINER, Chemical
TUBING, Vinyl
SWIVEL,1/4 NPSM x 3/8 NPT
BRACKET, Support
WASHER, Flat 5/l 6
WASHER, Lock 5/l 6
SCREW, Cap, hex hd

5/16-18 x 3/4

GROMMET Rubber

INJECTOR, Chemical
ADAPTER, 3/8 6 x 318 NPT
WASHER, Flat

UNLOADER, 800 PSI

PIN, Cotter l/8 x 1 -l/2

SWIVEL, 3/8 NPSM x 3/8 NPT

NIPPLE, Hex,

3/8 NPSM x 3/8 NPT
ELBOW, Street 3/8
PLUG, Square Head l/4
HOSE BYPASS (incl28)
NUT Hex 5/16-18
BUMPER
SCREW, Cap, hex hd

5/16-18x 1
WHEEL & TIRE ASSEMBLY

WASHER, Flat

AXLE
CHASSIS
SCREW, Cap, hex hd

3/8-16x l-1/4

WASHER, Flat 3/8

NIPPLE, Hex

3/8 NPSM x l/4 NPT

NOZZLE, Adjustable

WASHER, Lock 3/8

NUT, Hex 3/8-l 6
FRONT LEG ASSEMBLY
HirKly~es 26, 27, 48, 49,50)

QTY

8’ ft

1

1:

8
4

1
:
:

2
1

;

:
4
1

4
4

1

1

150

1

1
4
4

1

1

REF
NO.

iz

36

ii
39
40
41
42

PART
NO.

801-967
402-278
801-112
801-110
801-111
801-090
801-935
801-957
800- 154

43 800-396

z
46
47

801-666

803-350

801-103

801-009

48
3:

53
z

56
57
58
59

:i

E

66
67

:9”
70

101-566

80 l-504

801-858

803-l 85

803-l 55

803-309

801-937

802-765

161-162

801-612

105-659
803-l 65
803-396
801-008
803-083
803-308
801-226
802-l 36
801-202
800-376

DESCRIPTION QTY

HOSE, High Pressure 30’

1

PLUG, Plastic

1
STRAINER, Garden Hose
ADAPTER, Garden Hose

:

NUT, Garden Hose

1

QUICK COUPLER, Male l/4

WAND. 20”

:
SLEEVE, i 8”

1

PUMP & MOTOR ASSEMBLY

(see page 16)

1

GUN & WAND ASSEMBLY

(incl 29, 40, 41, 45, 46, 47)

TIP, Spray, 15 degree

:

GUN, Spray

1

NIPPLE, Hex l/4 x 3/8

1

QUICK COUPLER, Female l/4

(incl 70)

1

NUT Hex Lock 3/8-l 6
BUMPER, Rubber

:

BRACKET, Front Leg

1

LABEL, Warning, cordset

1

CORD SET, GFCI

1

SWITCH, Toggle

1

NUT, Lock, electrical
CORD GRIP

:

WASHER, Rubber

1

WASHER, Flat

1

COVER, Toggle Switch

1

LABEL, Caution, 115V

1

LABEL, Caution/Warning

LABEL, Grace G

:

LABEL, Keep from Freezing

TERMINAL, Slide

;

CONNECTOR, Wire

TERMINAL, Slide i

O-RING, Female coupler, l/4 1
HOSE ASSEMBLY, w/Quick Couplers

(incl 34, 39, and l/4 female QC)

308-518

13

PARTS DRAWING

800-268 Hydra-Clean@ 1235 Pressure Washer

62

MOTOR

230 VOLT,

1 PHASE

5

37

.

56
57

58
59

,/----7

39

16

1

I

\

/

\ '

I

b'

/

/

50

i

,’

I

I

I

I

L\ i

*-79 i

17

I

%-

17 1

L lb----+

------

_I

14 308-518

800-268 Hydra-Clean@ 1235 Pressure Washer

REF

PART

NO.

NO.

1

800-394

2

801-090

3

801-007

4

801-009

5

402-278

6

800- 135
7 800- 134
8

800-060
9 800-061

10 801-012
11 801-541
12

800-374

13

803-350

14

800- 175

2
17
18

801-878
801-363
801-015
801-546

800-274

802-l 39

801-235

106-062

801-880

104-811

801-941
801-023

801-025
801-024

801-539

801-008

176-250

803-083

803-396
80 l-445
803-l 86
800-248

DESCRIPTION

QlY

GUN & WAND ASSEMBLY

(incl 4,13, 49, 50, 54)

QUICK COUPLER, Male l/4

HOSE, High Pressure 50’
QUICK COUPLER, Female l/4

PLfZt Xstic

TIP AiSEMBLY, 0 Degree

(incl2, 74)

TIP ASSEMBLY, 15 Degree

(incl 2, 75)

TIP ASSEMBLY, 25 Degree

(incl 2, 76)

TIP ASSEMBLY, 40 Degree
G#%t?E??Rubber

HANDLE ’
HOSE ASSEMBLY w/Quick

Couplers (incl2, 3, 4)

GUN, Spray

FRONT LEG ASSEMBLY

(incl 17, 18, 78, 79, 80)
NUT Hex 3/8-l 6
WASHER, Lock 3/8
WASHER, Flat 3/8
SCREW, Cap, hex hd

3/8-16x l-1/4
CHASSIS
AXLE
WASHER, Flat
WHEEL & TIRE ASSEMBLY

PIN, Cotter 1/8x l-1/2
HUB CAP
SCREW, Cap, hex hd

5/16-18x 1
WASHER, Flat 5/l 6
WASHER, Lock 5/l 6
NUT, Hex 5/l 6-l 8

BUMPER
LABEL, Grace G
LABEL, Warning

LABEL, Keep From Freezing
LABEL, Caution & Warning
LABEL, Caution 230 Volt
LABEL, Warning Cordset
PUMP & MOTOR ASSEMBLY

(see page 17)

3

1
1
1
1
1

4

1
1

1
1

4

1:

8

12

8
4

:
1

1
1
1
1

1

REF

3”70-

{

41
42
43
44
45
46
47
48

9:
:;

74
75
76
77

si
80

PART
NO. DESCRIPTION

801-523 NIPPLE, l/2 x 2
801-106 TEE, l/2

801-l 78 ELBOW, Street l/2

800-l 15 THERMAL RELIEF VALVE
802-666 TEE, Street

800- 113 FILTER

801-l 11 NUT, Garden Hose
801-l 10 ADAPTER, Garden Hose

801-l 12 STRAINER, Garden Hose

801-866 HOSE, Bypass (incl73)
801-620 ELBOW, Street l/4

802-842 UNLOADER, 1200 PSI
801-935 WAND, 20”
801-957 SLEEVE, 18”
801-890 SWIVEL, 3/8 NPSM x 3/8 NPT
801-891 NIPPLE, Hex

3/8 NPSM x 3/8 NPT
801-709 PLUG, Square Head l/4
801-103 NIPPLE, Hex 3/8 x l/4
803-262 BRACKET, Switch Right
803-263 BRACKET, Switch Left
802-732 WASHER, Flat #6
802-731 WASHER, Lock #6
801-633 NUT, Hex #6-32
801-227 SCREW, Machine,

round hd #6-32 x 3/4
803-021 SWITCH, 230 Volt 1 Phase

QTY

1
1

:
i

1
1

:
1
1
1
1
1

i

2

1

1
4
4
4

4

1

801-929 CONNECTOR, Conduit 3/8 x 90” 2
801-930 CONDUIT, Sealtight 3/8 7 in
801-221 TERMINAL, Ring #lO 1
801-304 TERMINAL, Ring #8 1
801-226 CONNECTOR, Wire 4
801-303 WIRE, 14AWG Green 18 in
801-228 WIRE, 14AWG Black 18 in
801-229 WIRE, 14AWG White 18 in
801-937 NUT, Lock Electrical 1
801-931 CORD GRIP 1
803-149 CORD SET 1
802-627 NIPPLE, Hex

3/8 NPSM x l/4 NPT 1
801-665 TIP, Spray 0 Degree 1
801-666 TIP, Spray 15 Degree
801552 TIP, Spray 25 Degree :
801-553 TIP, Spray 40 Degree 1

101-556 NUT, Lock 3/8-l 6 1
801-504 BUMPER, Rubber 1
801-858 BRACKET, Front Leg 1

308-518 15

PARTS DRAWING

800-154 Pump and Motor Assembly

PARTS LIST
800-154 Pump and Motor Assembly

REF PART
NO. NO.

1 801-862
2 801-864
3 801-870

4 801-871
2 801-872 801-023
i 801-139 801-015

9 801-363

10 802-818

11 801-887

12 801-l 37

DESCRIPTION

MOTOR, 1.5 hp TEFC, 1 phase

(incl 12)

PUMP, 800 psi (see parts

drawing, page 18)
HOUSING, Coupler
COUPLER (incl 11)
SCREW, Cap, hex hd M6 x 20

WASHER, Flat ,1/4

WASHER, Lock, l/4

WASHER, Flat, 5/16
WASHER. Lock. 318

BOLT, Hex Hd, $8-16 x 1
SPIDER
KEY

QTY

1

1

16 308-518

PARTS DRAWING
800-248 Pump and Motor Assembly

PARTS LIST
800-248 Pump and Motor Assembly

REF PART
NO. NO.

1 802-625
2 802-629
3

802-633

2

802-698
802-786

6

801-139
7 802-784
8

802-785
9

801-887

10

801-137

DESCRIPTION QTY

MOTOR, 3.0 hp TEFC, 1 phase

(incl 10)

1

PUMP, 1200 psi (see parts

drawing, page 20)

1

HOUSING, Coupler

1
COUPLER (incl 9)
SCREW, Cap, hex hd M6 x 16

:

WASHER, Lock l/4

4

WASHER, Lock l/2

4

SCREW, Cap, socket hd

1/2-13x l-1/4

4

SPIDER

1

_ KEY

1

308-518 17

PARTS DRAWING

802-285 Pump Assembly,

800 psi

18
I
I

I 7

11-i 6

I

14

-

d

1

I

I

18 308-518

PARTS LIST

802-265 Pump Assembly, 800 psi

REF
NO.

1

2
3
4
5
6
7
8

9
10
11
12
13
14
15
16
17
18
19

20
21
22
23
24

PART
NO. DESCRIPTION

801-899 MANIFOLD, Aluminum
802-795 MANIFOLD, Brass
801-651 SCREW, Cap, socket hd.
801-652 WASHER, Lock
KIT 1 O-RING
KIT 1

SEAT, Valve

KIT 1

PLATE, Valve
KIT 1 SPRING
KIT 1 GUIDE, Valve
KIT 4 O-RING
KIT 4 CAP
KIT 1

VALVE ASSEMBLY
KIT 19, 27 PACKING
KIT 27

RETAINER, Packing

KIT 27 RING, Head

KIT 27 RETAINER, Packing
KIT 27 O-RING
KIT 23

SEAL, Oil
803-265 SCREW, Cap, hex hd
803-266 COVER, Crankcase
803-267 SPACER
803-268 O-RING
803-269 BEARING, Ball
803-270 CRANKCASE
801-659 DIPSTICK

QTY

1

1
6
6

REF

2.

26
27
28
29
30
31
32
33
34
35
36
37
38

39
40
41
42
43
44
45
49
50
51
52

PART
NO.

DESCRIPTION

803-271 GASKET, Cover
803-272 COVER, Crankcase

803-273 SCREW, Cap, socket hd.
KIT 6 O-RING
802-345 GAUGE, Sight
802-793 PLUG, Oil Drain
803-274 CRANKSHAFT
803-275 PIN, Wrist
802-794 KEY
803-276 ROD, Connecting
803-277 WASHER, Flat
803-278 WASHER, Lock
803-279 SCREW, Cap, socket hd.
803-280 GUIDE, Piston
801-489 WASHER, Flinger
801-661 PLUNGER, Ceramic

KIT 6 RING, Backup
KIT 6 WASHER

KIT 6 SCREW, Piston
803-281 SPACER
803-282 SEAL, Crankshaft
801-484 PLUG, Hex
801-482 PLUG, Hex
801-483 WASHER, Flat
801-485 WASHER, Flat

QTY

1
1

4

1
1
1

2

1
2
4

4

4
2

2

2

Kit
No.

6

23

27

Repair Kit
Part No.

801-472

Valve

802-306
Valve Cap

801-474

Plunger
Repair

801-662

Packing

801-658

Oil Seal

801-664

Packing &
Retainer

Ref
No.

4
5

6

7

8
11

28
41
42
43

12
13
14
15
16

Qty-

Description

Incl.

O-ring 6
Seat, valve 6
Plate, valve

6
Spring 6
Guide, valve

6
Valve Assy.

6
O-ring

6
Cap

6
O-ring

3
Ring, backup

3
Washer

3
Screw, piston 3

Packing

6

Seal, oil

6

Packing 1
Retainer, packing 1
Ring, head 1
Retainer, packing 1
O-ring 1

308-518

19

PARTS DRAWING
802-629 Pump Assembly, 1200 psi

I

I

20 308-518

802-629 Pump Assembly, 1200 psi

REF
NO.

1
2
3
4
5
6

;

9

10
11
12
13
14
15
16
17
18

19
20
21
22
23
24
25

PART
NO. DESCRIPTION

802-319 MANIFOLD, 1200 psi
801-651 SCREW, Cap, socket hd.
801-652 WASHER, Lock
KIT 1 O-RING
KIT 1

SEAT, Valve

KIT 1

PLATE, Valve
KIT 1 SPRING
KIT 1

GUIDE, Valve
KIT 4 O-RING
KIT 4 CAP
KIT 1

VALVE ASSEMBLY
KIT 19, 27 PACKING
KIT 27

RETAINER, Packing

KIT 27

RING, Head

KIT 27

RETAINER, Packing
KIT 27 O-RING
KIT 23

SEAL, Oil
803-265 SCREW, Cap, hex hd
803-266 COVER, Crankcase
803-267 SPACER
803-268 O-RING
803-269 BEARING, Ball
803-326 CRANKCASE
801-659 DIPSTICK
803-327 GASKET, Cover

QTY

1
8
8

REF
!I?

27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
49
50
51
52

PART
NO.

DESCRIPTION

802-526

COVER, Crankcase
803-273 SCREW, Cap, socket hd.
KIT 6

O-RING
802-345

GAUGE, Sight
802-793 PLUG, Oil Drain
803-329

CRANKSHAFT
803-275

PIN, Wrist
802-794

KEY
803-276

ROD, Connecting
803-277

WASHER, Flat

803-278

WASHER, Lock
603-279 SCREW, Cap, socket hd.
803-330

GUIDE, Piston
801-660

WASHER, Flinger
801-661

PLUNGER, Ceramic

KIT 6

RING, Backup

KIT 6

WASHER
KIT 6

SCREW, Piston

803-281

SPACER

803-282

SEAL, Crankshaft

801-484

PLUG, Hex

801-482

PLUG, Hex

801-483

WASHER, Flat
801-485

WASHER, Flat

QPY

5

1
1

i

1

3

6

6
6
3
3
3

Kit
No.

19

23

27

Repair Kit Ref
Part No. No. Description

801-472

4

O-ring

Valve 5 Seat, valve

6 Plate, valve
7 Spring
8 Guide, valve
11 Valve Assy.

802-306

9 O-ring

Valve Cap 10

Cap

801-474

28

O-ring

Plunger 41

Ring, backup

Repair

42 Washer
43 Screw, piston

1 1

801-662 I12 1 Packing
Packing

801-658

17

Seal, oil

Oil Seal

6

801-664

12

Packing

1

Packing & 13 Retainer, packing

1

Retainer 14

Ring, head

1

15 Retainer, packing

1

16 O-ring

1

QW

Incl.

6
6

308-518 21

ACCESSORIES

(Must be purchased separately)
DOWNSTREAM CHEMICAL INJECTOR KIT

(1235) 800-l 11

For injecting harsh cleaning chemicals downstream

from the pump.

UPSTREAM CHEMICAL INJECTOR KIT
600-257

For injecting mild cleaning chemicals upstream into the
pump.

ANTI-FREEZE FLUSH KIT 802-327

For flushing system with 50% anti-freeze solution prior
to transporting or storing pressure washer in below
freezing temperatures.

INLET PRESSURE REGULATOR 800-258

Regulates inlet water pressure to 60 psi (4 bar)

maximum.

BACKFLOW PREVENTOR 801-133

Prevent back-up of contaminated water into fresh
supply. Install upstream of pump.

TECHNICAL DATA

Model 800-093

Model 800-268

inotor (Totally Enclosed

1.5 hp, 1 phase

3.0 hp, 1 phase

-an Cooled)
:lectrical Service

115 volt/l5 amps/60 Hz

230 volt/20 amps/60 Hz

Vater Pump Maximum 800 psi (55 bar)

1200 psi (82 bar)

Vorking Pressure
nlater Pump Maximum Flow

2.6 gpm (10 Ipm)

3.5 gpm (13 Ipm)

Jnit Weight 90 Ibs (41 kg)

140 Ibs (64 kg)

Iimensions

Length

36 in (991 mm)

39 in (991 mm)

Width

19 in (482 mm)

21 in (533 mm)

Height

20 in (508 mm)

21 in (533 mm)

vlaximum Inlet Water 160” F (70” C)

160” F (70” C)

remperature
nlet Hose Connection

3/4 in garden hose (f)

3/4 in garden hose

(9

Netted Pans

High Pressure Hose

Acrylonitrile and Buna-N cover and tube

Bypass Hose

Synthetic yarn and EPDM

Pressure Washer

Anodized aluminum, Aluminum or Bronze alloys, Brass, Copper, Nylon-T composite,

(including fittings)

Ceramic, Buna-N, Cotton Phenolic, 303, 304, and 316 Stainless Steel, Polymide-12
Thermoplastic, @, Carbon Steel, Zinc with or without Yellow Chromate Plate P

egistered trademark of the DuPont Company

22 308-518

THE GRACO WARRANTY

WARRANTY AND DISCLAIMERS
Grace warrants all equipment manufactured by it and bearing its name to be free from defects in material
and workmanship on the date of sale by an authorized Grace distributor to the original purchaser for use.
As purchaser’s sole remedy for breach of this warranty, Grace will, for a period of twenty four months from
date of sale, repair or replace any part of the equipment proven defective. This warranty applies only when
the equipment is installed, operated and maintarned in accordance with Grace’s written
recommendations.

This warranty does not cover, and Grace shall not be liable for, any malfunction, damage or wear caused
by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance,
negligence, accident, tampering, or substitution of non-Grace component parts. Nor shall Grace be
liable for malfunction, damage or wear caused by the incompatibility with Grace equipment of structures,
accessories, equipment or materials not supplied by Grace. or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by
Grace.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective for
examination by Grace to verify the claimed defect. If the claimed defect is verified, Grace WIII repair or
replace free of charge any defective parts. The equipment will be returned to the original purchaser
transportation prepaid. If inspection of the equipment does not disclose any defect in material or
workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts,
labor and transportation.

DISCLAIMERS AND LIMITATIONS

THE TERMS OFTHIS WARRANlY CONSTITUTE THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY

AND ARE IN LIEU OF ANY OTHER WARRANTIES (EXPRESS OR IMPLIED). INCLUDING WARRANlY OF
MERCHANTABILITY OR WARRANTY OF FITNE‘SS FOR A PARTlCUtiR PURPOSE, AND OF ANY
NON-CONTRACTUALLIABILITIES. INCLUDING PRODUCT LIABILITIES. BASEDON NEGLIGENCEOR
STRICT LlABlLllY EVERY FORti OF LIABILITY FOR DIRECT. SPiClAL OR CONSEQUENTIAL
DAMAGES OR LOSS IS EXPRESSLY EXCLUDED AND DENIED. IN NO CASE SHALL GRACO’S
LIABILITY EXCEED THE AMOUNT OF THE PURCHASE PRICE. ANY ACTION FOR BREACH OF
WARRANTY MUST BE BROUGHT WITHIN THREE (3) YEARS OF THE DATE OF SALE.

EOUIPMENT NOT COVERED BY GRACO WARRANTY
GRACO MAKES NO WARRANP/ AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO ACCESSORIES, EQUIPMENT.
MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but
not manufactured by Grace (such as electric motor, switches, hose, etc.) are subject to the warranty, if
any, of their manufacturer. Grace WIII provide purchaser with reasonable assistance in making any claim
for breach of these warranties.

IMPORTANT PHONE NUMBERS

TO PLACE

AN ORDER,

contact your Grace distributor, or call this number to identify the

distributor closest to you: l-800-328-0211 Toll Free

FOR TECHNlCAL ASS/STANCE,

service repair information or assistance regarding the

application of Grace equipment: l-800-543-0339 Toll

Free

Factory Branches: Atlanta, Chicago, Dallas, Detroit, Los Angeles, West Caldwell (N.J.)

Subsidiary and Affiliate Companies: Canada; England; Switzerland; France; Germany; Hong Kong; Japan

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441

PRINTED IN U.S.A. 308-518 2/90