Graco cozyduet Owner's Manual

CozyDuet

™

PD314789E 5/15

2-A Parts List
2-B Features on Certain Models

1 WARNING

2 Features

3-A Assembling Swing Frame
3-B Assembling Rocker

3-C Attach Rocker to Frame cadre

3 Assembly

4-A To Secure Child

4-B To Use Vibration
4-C Installing Batteries (not included)

4-D To Use Wall Plug
4-E Starting Swing (4 Speed)

4-F Problem Solving

4 Use

5-A Care and Maintenance

5 Cleaning

Prevent serious injury or death: Failure to follow these

warnings and the assembly instructions could result in serious

injury or death.

• PLEASE SAVE OWNER’S

MANUAL FOR FUTURE USE.

• THIS PRODUCT REQUIRES
ADULT ASSEMBLY. Follow
assembly instructions carefully.

If you experience any difficulties,
please contact the Customer
Service Department.

• TO PREVENT SERIOUS INJURY

OR DEATH FROM INFANTS
FALLING OR BEING
STRANGLED IN STRAPS:

•

Always secure infant in the
restraint system provided.
After fastening buckles,
adjust belts to get a snug fit
around your infant.

• Never leave infant

unattended in swing.

• Never carry swing with infant

in it.

• Discontinue use of swing

when infant attempts to climb
out or reaches 30 pounds
(13.6 kg).

STRANGULATION HAZARD:

• DO NOT suspend strings

over the product or attach
strings to toys.

• DO NOT place product in any
location where there are
cords, such as window blind
cords, drapes, phone cords,
etc.

• Strings can cause
strangulation. DO NOT place
items with a string around
your child’s neck, such as
hood strings or
pacifier cords.

• DO NOT USE THIS PRODUCT if
it is damaged or broken.

•

NEVER USE as a car seat.

• ROCKER MODE:

• Never leave child unattended.

• This product is not intended
for unsupervised or prolonged
periods of sleep.

• Never use for a child able to sit
up unassisted.

• NEVER use this product as a
means to transport an infant in a
motor vehicle.

• NEVER use this product to carry
or transport a child.

FALL HAZARD:

READ ALL INSTRUCTIONS
BEFORE USE OF THIS ROCKER.

• Always use restraint system.
Adjust belt as needed to get a
snug fit around your child.

• Child’s movement can slide
product. Use only on floor. Never
place product near edges of
counter tops, tables or other
elevated surfaces.

• Maximum recommended
height is 27 inches (68.2 cm)
and weight is 18 pounds
(8.2 kg).

STRANGULATION HAZARD:

• Children have STRANGLED in
loose or partially buckled
harness straps. Fully restrain the
child at all times.

SUFFOCATION HAZARD:

• Product can roll over on soft
surfaces and suffocate child.
NEVER place product on beds,
sofas, cushions or other soft
surfaces.

• DO NOT place product near
water and moisture. Do not use
the product near possible wet
areas, such as a bathtub, show­er, wash basin, sink, laundry
tub, swimming pool, wet base­ment, etc.

• DO NOT use the AC adapter if it
has been exposed to
liquids, has been dropped,
or is damaged.

• Protect the power cord. Place it
so it is not walked on or pinched
by furniture or other items.

• DO NOT use with an
extension cord.

• Use only power cord
provided.

FOR SAFE BATTERY USE:

Keep the batteries out of children’s reach.
Any battery may leak battery acid if mixed with a different battery

type, if inserted incorrectly (put in backwards) or if all batteries are
not replaced or recharged at the same time. Do not mix old and new
batteries. Do not mix alkaline, standard (carbon-zinc) or rechargeable
(nickel-metal hydride, nickel-cadmium) batteries.

Any battery may leak battery acid or explode if disposed of in fire or
an attempt is made to charge a battery not intended to be recharged.
Never recharge a cell of one type in a recharger made for a cell of
another type.

Discard leaky batteries immediately. Leaky batteries can cause skin
burns or other personal injury. When discarding batteries, be sure to
dispose of them in the proper manner, according to your state and
local regulations.

Remove batteries before storing product for a prolonged period of
time. Batteries left in the unit may leak and cause damage.

Recommended type batteries—alkaline disposables, 4-D (LR20-1.5V)
3-AA (LR6-1.5V). NEVER mix battery types. Change batteries when
product ceases to operate satisfactorily.

Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.

NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device,pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the
following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that
to which the receiver is needed.

• Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations. CAN ICES-3 (B) /NMB-3
(B).

2-A Parts list

This model may not include some features shown below. Check that you

have all the parts for this model BEFORE assembling your product. If any

parts are missing, call Customer Service.

Tools required:

Phillips Screwdriver

ALL MODELS

FEATURES ON CERTAIN MODELS

4X

Styles vary

2-B Features on Certain Models

Only use this head support on this
swing. Never use this head support
on any other product.

This model may not include some features.

DO

NOT use any other accessories with this product.

Head support

Styles vary

Crotch strap cover

3-A Assembling Swing Frame

1. Rotate frame legs open.

SNAP!

SNAP!

2. Insert frame arm without wires
into leg as shown.

3. Under leg hub, press in button on
the frame arm and push frame
arm down so the button snaps
into hole as shown.

SNAP!

SNAP!

4. Connect red and black wire on
frame arm to red and black wire
in the opening of the frame leg as
shown.

5. Connect white wire on frame
arm to white in the opening of the
frame leg as shown.

6. Push connected wires into
opening in frame leg.
NOTE: DO NOT insert into leg
tube.

7. Insert frame arm into leg as
shown. CHECK wire is not
pinched between tube & plastic.

SNAP!

SNAP!

8. Under leg hub, press in button on
the frame arm and push frame
arm down so the button snaps
into hole as shown.

1. Rotate seat legs out from seat.

3-B Assembling Rocker

2. Place rocker tube over seat legs
as shown. Line up bosses in seat
legs with holes in rocker tube.

4X

3. Attach rocker legs wth 4 screws.

4. Insert rocker handle into
openings in side of seat. Press
buttons in on both sides of handle
and push down to lock handle into
seat.

SNAP!

4X

5. Insert seat wire into holes in seat

as shown.

6. Wrap webbing straps around seat
wire and attach snaps.

7. Attach bottom flaps at center snap,
wrap around seat wire and attach
to center snap on top flap.

8. Wrap bottom flaps over wire and
attach to top flap with snap and
hook and loop tabs.

9. Repeat on other side.

3-C Attach Rocker to Frame

1. Insert Rocker handle into
openings in frame as shown.

2. Release down until rocker handle
locks into place.

4-A To Secure Child

WARNING Falling Hazard: Always use the seat belt.

1.. o open, press button on buckle
to release the waist straps.

2.. o close, slide shoulder strap
connectors to waist straps and
insert into buckle.

3. Use slide adjuster at shoulder and
waist for tighter adjustment.

4. When changing harness strap
slots, MAKE SURE harness
straps are going through same
slots in seat pad.

5. The harness straps must go into
the slot that is even with or
slightly above the shoulders.
Avoid twisting straps.

4-B To Use Vibration

1. Disconnect snaps and hook and
loop tabs from back of seat. and
unwrap bottom of seat pad from
seat.

2. Remove battery lid on
vibration unit with a key.

3. Insert 3-AA (LR6-1.5V)
batteries in module.

4. Replace lid and seat pad.

5. Vibration: Turn to one of two set­tings.
Music: Turn to hear music or
ocean waves.
Automatically shuts off in 30
minutes. Turn off and back on to
restart.

4-C Installing Batteries (not included)

WARNING

To avoid injury: Remove child from swing before changing batteries.

1. With baby out of swing, open
the battery compartment lid
by inserting a screwdriver into
the coin slot. Insert four
D (LR20-1.5V) cell batteries.

CHECK that the batteries are
put in correctly. Your swing will

not run if the batteries are put in
backwards.

4-D To Use Wall Plug

WARNING Product does not recharge batteries. When AC

adapter is in use, batteries will automatically shut off.
DO NOT place product near water and moisture. Do not use the product

near possible wet areas, such as a bathtub, shower, wash basin, sink,
laundry tub, swimming pool, wet basement, etc.

DO NOT use the AC adaptor if it has been exposed to liquids, has been
dropped, or is damaged.

Protect the power cord. Place it so it is not walked on or pinched by
furniture or other items.

WARNING Strangulation Hazard: Keep this cord out of the

reach of children. DO NOT use with an extension cord. Use only power
cord provided.

4-E Starting Swing (4 Speed)

WARNING avoid serious injury from falling or sliding out.

Always use seat belt. After fastening buckles, adjust belts to get a snug fit
around your infant.

TO TURN SWING ON:
Press On /Off button or press any speed from 1 to 4 and lightly push the
swing to get it started. Observe the swinging motion for a minute. It takes

time for the swing to adjust to a setting. Change setting if needed by
pressing one of the higher number buttons for faster speeds or lower number
buttons for slower.

TO TURN SWING OFF: Press center On/Off button. Your seat may be
stopped at any time the motor is running without damaging the motor.

Power ON/OFF

SPEED - Press On /Off button or
press any speed from 1 to 4. When
pressing On/Off button, it
automatically starts with the last
speed setting that was selected
before the swing was turned off.

ON/OFF POWER - Press to turn
ON and turn OFF. Press button to
stop swing motion.

4-F Problem Solving

SWING WON’T OPERATE:

1. No batteries in swing.

2. Batteries dead.

3. Speed setting too low.

4. Batteries in backwards — check “+” and “-”.

5. Corrosion on battery terminals. Rotate batteries in place against
terminals, or clean with sandpaper or steel wool if corrosion is severe.

6. Baby grabbing swing legs. (Discontinue use.)

7. Push swing to start.

SEAT DOESN’T SWING VERY HIGH:

1. Control setting too low.

2. Blanket hanging down, causing increased wind resistance.

3. Batteries too weak.

4. Baby too heavy or too active. (Discontinue use.)

5. Soft carpet (swings higher on hard floors).

5-A Care and Maintenance

• FROM TIME TO TIME CHECK YOUR SWING for loose screws, worn

parts, torn material or stitching. Replace or repair the parts as needed.
Use only Graco replacement parts.

• TO CLEAN SEAT COVER, Refer to your care tag on your seat pad for

washing instructions. NO BLEACH.

• TO CLEAN FRAME, use only household soap and warm water.

NO BLEACH OR DETERGENT.

• EXCESSIVE EXPOSURE TO SUN OR HEAT could cause fading

or warping of parts.

To Remove Harness Cover and Head Support for Cleaning

1. Lift flap on harness cover.

2. Open harness.

3. Remove harness cover.

5. Reverse steps to re-attach crotch
pad and head support.

To Remove Seat

Pad for Cleaning

1. Disconnect snaps and hook and
loop tabs on back of seat pad.

4. Remove head support.

3. Insert harness shoulder straps
through seat pad as shown and
remove seat pad from frame.

2. Disconnect webbing snaps from
seat wire.

4. Pull seat pad off of seat frame.
Reverse steps to re-attach.