Graco 313704E User Manual

Instructions

GL-11

®

Injector

313704E

For Single-Line Parallel Automatic Lubrication Systems. For professional use only.

Part No.: 24A918

3500 psi (24 MPa, 241 bar) Maximum Working Pressure

Important Safety Instructions

Read all warnings and instructions in this manual. See
your Automatic Lubrication System Manual for com-

PRESSURE RELIEF PROCEDURE

Follow this procedure any time you are instructed to
Relieve the Pressure; shut off the pump; clean or ser­vice any part of the system; or install or clean dispens­ing devices.

1. Disconnect power.

2. Disable air supply to pump by either:

plete Warnings, Installation, Operation and Trouble­shooting instructions. Save all instructions.

EN

• Closing bleed-type air valve OR

• Disconnecting quick disconnect air coupler on
vent valve.

SKIN INJECTION HAZARD

High-pressure fluid from gun or dispense valve, hose
leaks, or ruptured components will pierce skin. This may
look like just a cut, but it is a serious injury that can
result in amputation. Get immediate surgical treat-

ment.

• Do not point gun or dispense valve at anyone or at
any part of the body.

• Do not put your hand over the dispense outlet.

• Do not stop or deflect leaks with your hand, body,
glove, or rag.

• Follow Pressure Relief Procedure, when you stop
dispensing and before cleaning, checking, or servic­ing equipment.

2.75”

69.8 mm

2-3/16” (55.6 mm)

1/8” npt

1/4” npt

1/2” npt

ti13690

9.5”

240.5 mm

3.75”

95.2 mm

2-27/32” (72.2 mm)

Parts

1

Torque to 70 - 80 ft lbs.

2

Apply grease/lubricant

3

Hand tighten until
contact with 8.

1

Ref. No. Part No. Description Qty.

1 15W653 HOUSING, injector 1
2 15W647 ADJUSTER, adapter 1

3

3

4

1

2

6

2

7

8

3 15W646 SCREW, adjusting 1
4 555303 NUT, jam, st 1/2-20 1
6* 122240 RING, sealing, valve 1
7* 122292 O-RING, inlet/outlet/adapter 2
8 24A916 PISTON, assembly 1
10* 122291 O-RING, piston 1
11* 122290 SPRING, injector 1
12 122293 SPACER, valve 1
13* 24B304 VALVE, honed 2
14* 122289 O-RING, valve body 2
15* 122288 RING, backup, piston 1
16 15W654 ADAPTER, inlet, injector 1
17 114916 KIT, fitting and cap, zerk 1

2

10

17

11

2

15

2

14

2

15

2

7

1

16

13

1

12

13

ti13692

Technical Data

Maximum Working Pressure 3500 psi (24 MPa, 241 bar)
Minimum Operating Pressure 1000 psi (6.9 MPa, 69 bar)
Suggested Operating Pressure 2500 psi (17 MPa, 172 bar)
Reset Pressure 600 psi (4.1 MPa, 41 bar)
Output Volume Per Cycle †Adjustable: 0.050 to 0.500

Wetted Parts Carbon steel, Stainless steel,

Recommended fluids Lubricant: NLGI 000 - NLGI

Inlet 1/2” - 14 npt
Outlet 1/4” - 18 npsf
Outlet 1/8” - 27 npsf

† Maximum adjustment setting is when adjusting screw (3) is just

making contact with indicator pin (8) with no inlet pressure. Turn
adjusting screw clockwise (in), to reduce output. To adjust,
loosen lock nut (4) and turn adjusting screw (3) the number of
turns indicated on the GL-11 Volume Adjustment Table to obtain
the desired volume. Tighten lock nut (4) when desired volume
setting is reached.

3

in.

Copper, Fluoroelastomer

#2

*Overhaul Kit 24B359 includes these parts.

Kits

24B359 KIT, overhaul, includes 5, 6, 7, 10, 11, 13, 14, 15 1
114916 KIT, fitting and cap, zerk 1

GL-11 Volume Adjustment Table

in.

Volume

3

cc

Description

Maximum Adjustment † 0 0.500 8.19
360° Clockwise Turn 1 0.468 7.67
360° Clockwise Turn 2 0.435 7.13
360° Clockwise Turn 3 0.403 6.60
360° Clockwise Turn 4 0.371 6.08
360° Clockwise Turn 5 0.339 5.56
360° Clockwise Turn 6 0.307 5.03
360° Clockwise Turn 7 0.275 4.51
360° Clockwise Turn 8 0.243 3.98
360° Clockwise Turn 9 0.211 3.46
360° Clockwise Turn 10 0.178 2.92
360° Clockwise Turn 11 0.146 2.39
360° Clockwise Turn 12 0.114 1.87
360° Clockwise Turn 13 0.082 1.34
Minimum Adjustment 14 0.050 0.82

Number of

Tu r ns

All written and visual data contained in this document reflects the latest product information available at the time of publication.

GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA

Copyright 2009, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.

Graco reserves the right to make changes at any time without notice.

Original instructions. This manual contains English. MM 313704

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

www.graco.com

Revised 11/2011