Graco 311440C User Manual

Instructions -- Parts List
Replacement PC Board Kit for: Ultra Max II 695/795/1095/1595t Ultimate Mx II 695/795/1095/1595t TexSprayt Mark IV, Mark V
Standard/
120 795 Standard 249647 249646 826071
North America Premium 249649 249648 826072
R
240 695 249665 249663
Europe 795 249666
240 695 249669 249668
Europe Multi-cord 795 249671
110 695 249673
UK 795 249674
240 695 249686 249685
Australia 795 249687
240 695 249682 249681
Asia 795 249683
100 695 249677 249676
Japan & Taiwan 795 249679 249678
* Not ETL approved All models not available in all countries.
Model
695 Standard 249643 249642 826068 826067
1095 Standard 249651 826073
1595 Standard 249658*
Mark IV 249636*
Mark V 249903*
1095 249667
Mark V 249905
1095 249672
Mark V 249907
1095 249675
Mark V 249906
1095 249688
1095 249684
1095 249680
Premium
Ultra Max II Ultimate Mx II
Premium 248645 249644 826070 826069
Premium 249653 826074
253060
Premium 249659*
253059
249904
311440C
EN
826075* 826082
826076* 826081
Pressure Relief Procedure
WARNING
INJECTION HAZARD
System pressure must be manu­ally relieved to prevent system
from starting or spraying acciden­tally. Fluid under high pressure can be in­jected through skin and cause serious injury. To reduce risk of injury from injection, splash­ing fluid, or moving parts, follow Pressure Relief Procedure whenever you:
D are instructed to relieve pressure, D stop spraying, D check or service any system equipment, D or install or clean spray tip.
Installation
1. Turn pressure to zero.
2. Turn ON/OFF switch to OFF.
3. Unplug power supply cord.
4. Hold metal part of gun firmly to grounded metal pail. Trigger gun to relieve pressure.
5. Lock gun safety latch.
6. Open pressure drain valve. Leave pressure drain valve open until ready to spray again.
If suspected that spray tip or hose is completely clogged, or that pressure has not been fully relieved after following steps above, VERY SLOWLY loosen tip
guard retaining nut or hose end coupling to relieve pressure gradually, then loosen completely. Now clear tip or hose obstruction.
795 EXAMPLE SHOWN
ti4413b
Fig. 1
CAUTION
Electrostatic discharges can damage components on PC board. Use a ground strap when handling or installing PC board. Using configurations other than those specified in Fig. 1 results in poor sprayer performance.
R125
R126
1095 795 695
North America, UK, Japan
120 Vac
695
795
1095
1595
Mark IV
Mark V
X
XX
XXX
X
287941
1.
Follow Pressure Relief Procedure.
2.
Remove PC board. See Manual 311365 or 311287 (Mark IV) for procedure.
3.
Fig. 1. Cut resistors from PC board.
4.
Install PC board. See Manual 311365 or 311287 (Mark IV) for procedure.
R127
R127R125 R126
X
XX
X
Cutting Instructions
X=Remove
International
240 Vac
695
795
1095
Mark V
X
XX
XXX
287942
R135R133 R134
X
XX
TO PLACE AN ORDER OR FOR SERVICE, contact your Graco distri but or, or call 1--800--690--2894 to identify the nearest distributor.
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
For patent information, see www.graco.com/patents. Original instructions. This manual contains English. MM 311440
Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES P.O. BOX 1441 MINNEAPOLIS, MN 55440 --1441 USA
Copyright 2004, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
Revised May 2013
2 311440
Loading...