Graco 214-627, 235-117 Instruction Manual

INSTRUCTIONS–P

This manual contains important
warnings and information.
READ AND RETAIN FOR REFERENCE

2

Quart Pressure Cup

50 psi (3.5 bar) Maximum Working Pressure

Part No. 214–627, Series B

0–50

psi (0–3.5 bar) Regulated Pressure Range

Part No. 235–117, Series A

0–15

psi (0–1 bar) Regulated Pressure Range

ARTS LIST

307–318

Rev.

H

Supersedes G

Table

Preparation
Operation 3
Service 4
Parts 4–5
Accessories 6
Graco T
Technical
Warranty 8

Hazard of using Fluid Containing Halogenated Hydrocarbons

Never use 1, 1, 1–trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluid
containing such solvents in this equipment. Such use could result in a serious chemical reaction, with the
possibility of explosion, which could cause death, serious bodily injury and/or substantial property damage.

for Operation2. . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

oll-Free Phone Numbers6. . . . . . . . . . . . . . . . .

Data8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

of Contents

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

WARNING



Consult your fluid suppliers to ensure that the fluids being used are compatible with aluminum parts.

GRACO INC. P.O. BOX 1441

�COPYRIGHT

MINNEAPOLIS, MN

1978, GRACO INC.

55440–1441

Preparation

for Operation

Prepare
manufacturer’
fine nylon mesh bag, available at paint dealers. Fill the
cup (Ref No. 27, page 4) with paint and screw it se
curely to the lid (19). T

the paint or other coating according to the

s instructions. Strain the paint through a

-

orque to 65 in–lb (10 N.m).

B

A

C

5

Connect the air (23) and fluid (25) hoses as shown in
Fig. 1. The recommended auxiliary equipment shown
in Fig. 1 can be found in the
page 6.

KEY

A Main
B On–Of
C
D
E Locking Screw
F Air Spray Gun
G
5
20
23 Air Hose
25

Air Supply

f V
1/4 npt Air Inlet
Air Filter

Air Adjusting V
Air Regulator
Air Control V

Fluid Hose

alve

alve

alve

25

Accessories

F

section on

G

Fig. 1

D

E

20

23





Operation

WARNING

To

reduce the risk of over-pressurizing the equip
ment, which could cause serious bodily injury
cluding splashing in the eyes or on the skin,

never

exceed 50 psi (3.5 bar) air pressure to the
cup. The relief valve is preset to relieve pressure at
50 psi (3.5 bar).
valve.

Do not

alter settings on the relief

, in

-

-

3. T

urn the air regulator (5) knob in until the gauge
reads 10 psi (0.7 bar). Turn the air regulator’s lock
ing screw (E)

wise

to unlock it.

4.

Spray a test panel. If the paint is not fully atom
ized, either decrease the cup fluid pressure with
the air regulator (5), or increase the atomizing air
pressure with the air adjusting valve (G). Always
use the lowest possible pressure needed to
achieve the desired results.

clockwise

to lock it and

counterclock-

-

-

urn on the air supply

1. T

2. T

urn the cup air control valve (20)

the way in.

.

clockwise

, all

5. T

o decrease the cup fluid pressure, turn the air
regulator (5) knob out
cup air control valve (20)
mentarily to bleed of
by turning in the air regulator knob.

(counterclockwise)

counterclockwise

f the excess air

. T

urn the

mo-

. Then reset it



Service

Cleaning the Cup

WARNING

To

reduce the risk of serious bodily injury
splashing in the eyes or on the skin,
lieve pressure in the cup (27) before removing the
lid (19) by turning the air regulator (5) knob all the
way out
control valve (20) thumbscrew

1. Relieve

2. Unscrew the air cap retaining ring on the spray gun

(counterclockwise)

pressure in the cup by

above.

3 turns. Hold a rag over the air cap and trigger

about

the

gun to force paint back through the hose (25) and

into

the cup (27).

and unscrewing the air

.

following the warning

, including

always re-

Parts

10

3. Turn

4.

NOTE: When replacing gasket (15), remove old adhe-

5. Remove the air cap from the spray gun and turn off

6. Turn on the air supply. Set the air regulator (5) at

7. Remove the solvent from the system and wipe the

16

of

f air supply. Empty the paint from the cup (27)

and clean the cup and lid (19). Be sure the solvent

is compatible with the fluid being sprayed.

used

Check the gasket (15) inside the lid (19). Replace if
damaged.

sive

from inside lid (19). Apply
#847 Scotch–Grip� or equivalent) to the lid when
installing

the air regulator (5). Fill the cup (27) with solvent,
replace

10 psi
until

clean solvent comes from the gun.

equipment

18

the new gasket.

lid (19), and close the air control valve (20).

(0.7 bar) and hold the spray

with a solvent dampened rag.

Ref 25

new adhesive (3M

gun trigger open

Place

wrench

here to remove

*15

*7

*17

12

8

1

29

22

19

14

2

13

9

20

4*

6

5*

28*

Ref 23

11

21

3

24

26



23

25

27

Slots

on bottom for assisting

in cap removal



Parts

Model 214–627, Series B

0–50 psi (0–3.5 bar) Regulated Pressure Range
Includes items 1–29

Model 235–117, Series A

0–15 psi (0–1 bar) Regulated Pressure Range
Includes items 1–29

Ref.
No.

Part No.

Description Qty.

Ref.
No.

Part No.

Description Qty.

1 100–032 SCREW
2 100–188 NUT
3 101–855 SCREW

No. 4 x 3/16”

104–655



*

111–500

104–815 REGULAT

*



111–501 REGULAT

6 183–697
7* 172–593* VAL
8 172–594 BRACKET
9 172–613
10 172–620 HANDLE 1
11 172–621

12 172–622 W
13 172–679 NUT
14 172–680 ELBOW
15* 183–337 GASKET
16 172–682

17* 172–684
18� 183–696

19 174–069 LID 1
20 174–075 VAL
21 174–100
22 176–243 LABEL 1

GAUGE, pressure;

Model 214–627 only

GAUGE, pressure;

Model 235–1

See Manual 308–167;

Model 214–627 only

Model 235–1

NIPPLE; 1/8 npt

ADAPTER, handle

ADAPTER, 7/16 unf(m)
x 1/8 npt(m) 1

ADAPTER; 3/8 npsm(m)
x 1/2 uns(f)
SPRING, compression
TEE; 1/4 npt(m) x 1/4 npt(m) x
1/8 npt(f)

CHAIN, ball; 3” (76.2 mm) long

, rd hd; 6–32 x 1/4”

, hex; 5/16–18

, rd hd, self–tapping;

17 only

OR, air; adjustable

OR, air; adjustable;

17 only

VE, check

, check valve

ASHER, flat; 1/4”

, hex; 3/8” x 1/8”

; 1/2 uns(f) x 3/8 npsm(m)

, cap

VE, air control

1

1
1

2

1

1

1

1
1
1
1
1

23 212–005

24 104–415 .COUPLING 2
25 212–006

26 104–084 .COUPLING 2
27 214–602 CUP 1
28*� 214–691 VAL
29 172–881 TUBE 1

306 & 307 numbers in description refer to separate
instruction manuals.

* Recommended

to

reduce down time.

HOSE, air; 1/4” ID, 6’ (1.83 m)
long; cpld 1/4 npsm(fbe) swivel;
Includes item 24

HOSE, fluid; 1/4” ID, 6’–8” (2.03 m)
long; cpld 3/8 npsm(fbe) swivel;
Includes item 26

VE, relief; 50 psi (3.5 bar).

”tool box” spare parts. Keep on

hand

1

1

1

Kits

� Relief Valve Kit 218–925

1
1
1
1

1
1

1
1

Model

214–627, “Series A” cups must order this kit to
replace the relief valve (item 28) and tee (item 18). The
kit includes Relief V
tee. Series A Pressure Cups must have both the tee
and relief valve replaced together for safety reasons.

alve 214–691 and the appropriate

Conversion Kit 235–115

To

convert Model 214–627 Pressure Cup to Model

235–1

17 Pressure Cup. Kit includes the following
parts.

Part No.

111–500

111–501 REGULAT

Description Qty.

GAUGE, pressure

OR, air; adjustable

1
1



Accessories

Use Only Genuine Graco Parts and Accessories

Air

Spray Guns

See the following manuals to select the appropriate
gun for your application.

Manual

No.

307–378
307–379
307–380

Air

Line Filter 106–148

250 psi (17 bar) Maximum Working Pressure

Removes harmful dirt and contaminants from the com
pressed air supply. 3/8 npt inlet and outlet.

Model

No.

600
700
800

Maximum W
Pressure

200 psi (14 bar)
200 psi (14 bar)
900 psi (62 bar)

orking

Air Adjusting V

100 psi (14 bar) Maximum Working Pressure

For controlling atomizing air to the gun. 1/4 npsm(m)
inlet and 1/4 npsm(f) swivel outlet.

-

Buna–N Air Hose (with neoprene cover)

200 psi (14 bar) Maximum Working Pressure

With reusable couplings and compression sleeves.
5/16 in. (7.9mm) ID, 1/4 npsm (fbe) swivel.

alve 205–090

Air Line Filter & Regulator 202–660

180 psi (12.6 bar) Maximum Working Pressure

1/2 npt(f) inlet and two 1/4 npt(m) outlets.

Graco

TO

PLACE AN ORDER

utor

, or call this number to identify the distributor

closest to you:

1–800–367–4023 T

, contact your Graco distrib

oll Free

Phone Numbers

Part No.

210–866

210–867

210–868

Nylon Fluid Hose 221–195

225 psi (15 bar) Maximum Working Pressure

1/4 in. (6 mm) ID, 6 ft. 8 in. (2.03 m) long,
3/8 npsm(fbe) swivel.

2 Quart Cup Liner 1

Packaged 20 in a box.
Polyethylene bag for easier cleanup.

-

FOR TECHNICAL ASSIST

information or assistance regarding the application of
Graco equipment:

Length

15’ (4.5 m)

25’ (7.6 m)

50’ (15.2 m)

12–491

ANCE,

1–800–543–0339 T

service repair

oll Free



Notes



The

Graco Warranty and Disclaimers

WARRANTY

Graco

warrants all equipment manufactured by it and bearing its name to be free from
date of sale by an authorized Graco distributor to the original purchaser for use. As purchaser’s sole remedy for breach of this war
ranty,

Graco will, for a period of twelve months from the date of sale, repair

This

warranty applies

dations.

only when the equipment is installed, operated and maintained in accordance with Graco’

or replace any part of the equipment proven defective.

defects in material and workmanship on the

s written recommen

-

-

This warranty does not cover
plication, abrasion, corrosion, inadequate or improper
component
structures,
or

maintenance of structures, accessories, equipment or materials not supplied by Graco.

This
claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be
returned
workmanship,

parts. Nor shall Graco

accessories, equipment or materials not supplied by Graco, or the improper design,

warranty is conditioned upon the prepaid return of the equipment claimed to be defective for examination by Graco to verify the

to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or

repairs will be made at a reasonable charge, which charges may include the costs

DISCLAIMERS

THE

TERMS OF THIS W

OR IMPLIED), INCLUDING WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND OF ANY NON–CONTRAC-

TUAL

LIABILITIES, INCLUDING PRODUCT LIABILITIES, BASED ON NEGLIGENCE OR STRICT LIABILITY

CONSEQUENTIAL DAMAGES OR LOSS IS EXPRESSLY EXCLUDED AND DENIED. IN NO CASE SHALL GRACO’S LIABILITY EXCEED THE AMOUNT OF THE

PURCHASE PRICE. ANY ACTION FOR BREACH OF WARRANTY MUST BE BROUGHT WITHIN TWO (2) YEARS OF THE DATE OF SALE.

EQUIPMENT

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH

RESPECT TO ACCESSORIES, EQUIPMENT, MATERIALS, OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO.

manufactured
will

provide purchaser with reasonable assistance in making any claim for breach of these warranties.

ARRANTY CONSTITUTE PURCHASER’S SOLE AND EXCLUSIVE REMEDY AND ARE IN LIEU OF ANY

NOT COVERED BY GRACO W

by Graco (such as electric motor

Technical

, and Graco shall not be liable for

be liable for malfunction, damage or wear caused by the incompatibility with Graco equipment of

AND LIMIT

ATIONS

Data

, any malfunction, damage or wear caused

maintenance,

negligence, accident, tampering, or substitution of non–Graco

ARRANTY

, switches, hose, etc.) are subject

Manual

. EVER

Y FORM OF

to the warranty

by

faulty installation, misap

manufacture, installation, operation

of parts, labor and transportation.

OTHER W

ARRANTIES (EXPRESS

LIABILITY FOR DIRECT

These items sold, but not

, if any

, of their manufacturer

, SPECIAL OR

. Graco

Change

-

Maximum Working Pressure
Regulated

Diameter 5.25 in. (133 mm).
Overall
Weight 4
Wetted

Pressure Range

Model 214–627

Model

235–1

.

. . . . . . . . . . . .

17

.

. . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . .

Height

.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts

.

. . . . . . . . . . . . . . . . .

.

. . . . . . . . . . . .

.

. . . . . . . .

Polyethylene, Aluminum,

50 psi (3.5 bar)

0–50 psi (0–3.5 bar)

0–15 psi (0–1 bar)

17.75 in. (451 mm)
lb (1.8 kg)

Nylon, Stainless Steel

Scotch–Grip� is a registered trademark of the 3M
Company.

Sales

Foreign Offices:

Offices:

Atlanta, Chicago, Dallas, Detroit, Los Angeles, Mt. Arlington (N.J.)

Canada; England; Korea; Switzerland; France; Germany; Hong Kong; Japan

Summary

This

manual was revised to add 2 Quart Cup Liners,

Part Number 1

12–491, to the accessories.

GRACO INC. P.O. BOX 1441

PRINTED



IN U.S.A.

MINNEAPOLIS, MN

307–318 4/78 Revised 6/94

55440–1441