Grace Digital GDI EGPB100 User Manual
Models: GDI-EGBP100-110
EcoPebble
USER GUIDE
QUICK START 4-STEPS CONTROL BUTTONS & OPERATIONS
Open the CAP on the BACK of your ECOPEBBLE.
1
2
Turn on the MAIN POWER SWITCH. Listen for
announcement, “Power On” / “Power On, Pairing
Ready” & look for the back panel LED to flash Blue.
Search your Smart Device for a Bluetooth
3
Connection and select ‘ECOXGEAR’. Listen for
announcement, “Bluetooth Connected.”
4
Select & Play your Music from your Smart Device.
IMPORTANT HINTS
• MAIN POWER SWITCH must be set to the ON position to operate your ECOPEBBLE.
• When the Main Power Switch is set ON, use the STANDBY POWER BUTTON to turn unit ON/OFF.
• PRESS & HOLD the STANDBY button for 3-5 seconds to power ON/OFF your ECOPEBBLE.
• When not in use for extended periods, set the Main Power Switch to the OFF position.
• Auto connect to your device by using the STANDBY button only to power ON/OFF, and do NOT turn OFF the Master
Power Switch. When the Master Power Switch is turned OFF, the ECOPEBBLE resets and previous connections
are deleted from the memory. When the Master Power Switch is turned ON, you must pair to your device again.
STANDBY ON/OFF
PRESS & HOLD the STANDBY
POWER button for 3-5 seconds to
turn it ON/OFF. ECOPEBBLE remains
in Standby Power mode when OFF.
IMPORTANT: Standby Power
function will NOT operate when the
Main Power is set OFF. Main Power
Switch on the back panel must be set
ON for Standby to operate.
TRACK SELECTION/
SPEAKER VOLUME
PRESS ONCE for previous track selection.
PRESS & HOLD to decrease the volume.
PLAY / PAUSE ANSWER
PRESS ONCE to pause & play
song tracks and to answer
incoming mobile calls.
TRACK SELECTION/
SPEAKER VOLUME
PRESS ONCE to advance the
track selection.
PRESS & HOLD to increase
the volume.
NOTE: Some Bluetooth
devices must be manually
set at maximum audio level.
Your ECOPEBBLE will beep
to indicate when maximum
volume setting is reached.
Power, Connections & INDICATORS Bluetooth Pairing & Audio
Fully charge your ECOPEBBLE BEFORE you power ON for best performance. Connect the USB INPUT to the
USB micro cable and a power source to charge your ECOPEBBLE.
When charged, set the Main Power Switch to ON. Press the Standby Power Button to power on the
ECOPEBBLE from standby mode and to return to standby mode.
RECOMMENDATION: Use the accessories included with the ECOPEBBLE for optimal performance.
LED STATUS
Power ON /
Bluetooth Paired
Bluetooth Pairing
Ready / Power ON
• POWER FEATURE: STANDBY Power will NOT operate when the Main Power Switch is set OFF.
Once the Main Power Switch is set to ON, use the Standby Button to turn the unit ON/OFF.
• When not in use for extended periods, turn the Master Power OFF to preserve battery life.
Charging*
Full Charge*
*when connected with USB cable
CONNECTING WITH BLUETOOTH: CONNECT TO YOUR SMART DEVICE & PLAY AUDIO
When your ECOPEBBLE is turned
ON, the LED light on the back panel
will flash BLUE, indicating the unit is
powered ON and ready to pair. The
unit shall also announce “Power ON”
or “Power ON, Pairing Ready” when
powered ON.
Turn on your Smartphone’s Bluetooth.
Set the Smartphone to pairing mode.
Available Bluetooth connections shall
appear. Select ‘ECOXGEAR’ from the
list of discovered devices on your
Smartphone. Wait a few seconds until
the connection is completed.
When the ECOXGEAR selection is
made and the Bluetooth connection
is complete, your ECOPEBBLE
announces, “Bluetooth connected.”
Once connected, select and play your
desired audio.
Your ECOPEBBLE should sync
& wirelessly pair with most
Bluetooth enabled devices. The unit
remembers the last device paired
and will automatically search for previous
connections when the speaker is turned
ON from Standby or when a device comes
back into Bluetooth range. If a connection
is dropped, the speaker will look to
re-establish that connection. If Bluetooth
is turned OFF on your Smartphone, the
ECOPEBBLE may not automatically look
for the device.
PAIRING MODE
When paired, if you wish to put your
ECOPEBBLE in pairing mode you can
turn off Bluetooth on the Smartphone
connected to the device or turn the Main
Power Switch OFF/ON. Your ECOPEBBLE
should announce, “Power ON, Pairing
ready” when main power is turned back
ON and the device is ready to pair to a
Bluetooth connection.
RECOMMENDATION: If you are not
familiar with Bluetooth pairing for your
Smartphone or other Smart-Device, refer
to the User Guide for your Smartphone
to learn how to add and pair a new
device (ECOPEBBLE for instance) to your
Smartphone using Bluetooth.
BLUETOOTH PAIRING &
CONNECTIONS
Once paired, should you have an
issue switching between Bluetooth
connections between devices, open
the Bluetooth Section within the
device currently connected to the
ECOPEBBLE and delete the Bluetooth
connection. The ECOPEBBLE will
then be available to pair & connect
to an alternate Bluetooth enabled
Smartphone / Audio Device.
SPECIFICATIONS
UNIT DIMENSIONS
Mount Attachment Point
2.9” 2.9”
2.8” 2.9”
UNIT WEIGHT
8.0 ounces
OUTPUT POWER
RMS 5W
(5 Watt mono speaker/ 4 ohms)
S/N RATIO
90dB +/- 3dB
POWER SOURCE
3.7V, 500mAh Lithium-ION Battery
USB INPUT / OUTPUT
5V~1A
PLAY TIME
6+ hours from full charge at 75%
vol. level
CHARGING TIME
Approximately 2 ½ hours
CHARGING OPTIONS
USB to adapter or computer
FREQUENCY RANGE
20Hz-18,000Hz
BLUETOOTH
Bluetooth® CSR 4.1
MOUNT ATTACHMENT POINT
¼” diameter for use with tripod stand
or mounts (available separately)
OPTIONAL ACCESSORIES
Suction Cup Mount (¼” mount)
Handlebar Mount Adapter (¼“ mount)
RECOMMENDED STORAGE (BATTERY)
TEMPERATURE
59°F / 15°C
WATERPROOF/DUST RATING
IP67
CARABINER CLIP & LANYARD
ECOPEBBLE UNITUSB CABLE
IMPORTANT NOTICE
WATERPROOF FEATURE
Your ECOPEBBLE is only waterproof when the BACK CAP is properly closed.
In order to properly close the cap, be sure the cap fits flat and flush along the
edges with the back panel. IF not properly closed the unit is NOT watertight
and may not float.
EcoPebble
USER GUIDE
USER GUIDE
FCC Compliance Statement & Warning:
This device has been tested & found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. The device generates, uses & can radiate radio frequency energy & if
not installed & used in accordance with instructions may cause harmful interference to radio communications. There is no guarantee that interference will not
occur in a particular installation. IF this device causes interference to radio or television reception try one of these measures: reorient or relocate the receiving
antenna, increase separation between device & receiver, connect the device into an outlet on a circuit different from that to which the receiver is connected,
consult a dealer or experienced radio / TV technician for assistance. Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the device and/or void the manufacturer’s limited warranty.
Product Use and Protection:
Read and Follow all Instructions. Use only as intended.
The ECOXGEAR Bluetooth speaker is intended to be used indoors or outdoors and in land or water environments. The speaker has been tested to IP67
waterproofing standards, which means the speaker can be submerged in up to 3 feet of water for 30 minutes without any damage. However, the speaker is
not intended for constant underwater use.
Always make sure the cap(s) / cover(s) are clean, free from sand or debris and correctly fitted. The speaker will only meet IP67 ratings if all rubber seals,
gasket(s) and cover(s) / cap(s) are in place. If you notice a muffling of audio after submersion gently shake the unit to clear excess water. If your speaker is
exposed to salt water clean it thoroughly after use with fresh water.
The USB cables, power adapters, and the unit with an improperly fitted cap, are NOT waterproof.
To prevent fire or shock, do not attempt to charge this unit if it is wet or you suspect water has entered the unit. In this situation, please return the unit to
Grace Digital for a free assessment. If we have found that the unit has carried water we will repair or replace the unit free of charge.
SAFETY ADVISORY & WARNING:
Read and Follow all Instructions. Use only as intended.
CAUTION:
Do NOT open to repair. A qualified technician must carry out repair work.
CAUTION:
ATTENTION: Do NOT charge while the unit is wet. Towel dry the unit AND make sure all connections are dry BEFORE plugging in the charging
connector. Failure to do so may result in electrical damage to the unit and may void the warranty.
WARNING:
This product may contain chemicals listed in Proposition 65 ( www.oehha.ca.gov/prop65/prop65_list/Newlist.html )
WARNING:
ECOPEBBLE has a built-in Lithium Ion battery. The battery must NOT be used in or near an open heat source or excessive heat.
WARNING:
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
ATTENTION:
Do NOT dispose of in a landfill. Contact Grace Digital at www.gracesupport.com or a certified recycling agent to dispose of the unit.
ATTENTION:
AC adapter is a device forming a part of the main plug therefore the AC adapter can always be readily disconnected from AC socket-outlet.
SAFETY
This product has a limited life span of use and should be replaced when it shows obvious signs of wear.
Do not modify or remove any original component parts of the speaker. Doing so could cause damage to the unit allowing water to ingress. A unit with water
ingress should not be charged due to potential risk of fire or shock.
Do not attempt to mount the unit except with the approved ECOXGEAR mounts. Doing so could cause damage to the unit allowing water to ingress. A unit with
water ingress should not be charged due to potential risk of fire or shock.
Please exercise care and good judgment when using your ECOXGEAR speaker. Audio levels should be appropriate to your environment, comply with all local
regulations, and always ensure that you can hear and be aware of any potential hazards around you.
You should always
1) Use the ECOXGEAR speaker in accordance with any music or noise rules and regulations.
2) Use the proper ECOXGEAR mounts if you intend to mount the unit.
3) Properly seal the ECOXGEAR prior and after each use when in humid or water environments to avoid water damage to the internal components. Salt
water / air is particularly corrosive. Always make sure that the gaskets are sealed when in salt water environment and the unit properly rinsed off after use.
4) Properly clean the ECOXGEAR and ensure the gaskets have no sand, dirt or water on them prior to storage or removing the back cover.
5) Store your unit with all caps properly sealed to avoid long term internal moisture damage inside your unit.
6) Completely dry and clean your ECOXGEAR prior to attempting to charge the unit.
7) Return the ECOXGEAR to Grace Digital if you suspect water ingress into the unit or if the unit has experienced a severe impact that may have affected the
integrity of the unit to take on water.
You should never
1) Charge your ECOXGEAR if you suspect water has entered the device. Charging a device with water inside could be potentially hazardous and cause fire or
a spark.
2) Use your ECOXGEAR if you have dropped it or thrown it against a hard surface which may have destroyed the integrity of the speakers, housings or
gaskets. In the event of a severe impact to your unit please return the unit to Grace Digital to review for potential damage.
3) Open the auxiliary door in a water environment. This could cause water to ingress into the unit which could potentially be hazardous and cause a fire or
a spark.
4) Connect a device to the auxiliary input jack when in a water environment. The auxiliary jack should only be used in a dry environment.
5) Attempt to fix, repair your ECOXGEAR unit. Please send it back to Grace Digital for any assessments and repairs.
Loading...