GPX C224B User Manual
Clock Radio with Dual Alarm
User’s Guide for Model C224B v981-01
FCC Warnings
Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Additional Warnings
• The apparatus shall not be exposed to dripping or splashing and that no objects lled with liquids, such as vases, shall be placed on apparatus.
• Do not place the unit on top of any soft, porous, or sensitive surfaces to avoid damaging the surface. Use a protective barrier between the unit and surface to protect the surface.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc) batteries.
• Batteries should be recycled or disposed of as per state and local guidelines.
FUNCTIONS AND CONTROLS
Battery Backup
The battery backup is intended for short power outages only.
The clock radio’s primary functions cannot run o of the battery
backup alone. Requires 2, AAA-size, batteries (not included).
Power
Plug the AC/DC power adapter (included) into the
DC Power Input on the unit, and a standard power outlet.
Volume/AL1/AL2
Press to adjust the volume.
Press to begin setting
Alarm 1 or Alarm 2.
Radio/Power
Press to power on the Radio.
Press and hold to power o
the Radio. Press briey
to switch between AM
and FM bands.
PM Indicator
Alarm 1 Buzzer/
Radio Indicator
Press to snooze the alarm after it sounds.
In on mode, press repeatedly to set the sleep timer.
Snooze
LED Display
Alarm 2 Buzzer/
Radio Indicator
Tuning/Min/Hour
Press to tune the radio.
Press to adjust the minute
or hour when setting
the clock or alarm.
Preset/Clock
With the Radio on, press to
cycle through preset radio
stations. In o mode,press and
hold to adjust the clock.
CLOCK AND SLEEP TIMER
Setting the Clock
1. Press and hold the Preset/Clock button until the display begins ashing.
2. Press the Hour and Minute buttons to adjust the time. The PM indicator will light when the hour is set in the PM.
3. Press the Preset/Clock button again to nish, or wait for the display to stop ashing.
Setting the Sleep Timer
1. Power the radio and press the Snooze button to adjust the timer ( 90, 80, 70, 60, 50, 40, 30, 20, 10 min or OFF ).
2. Once the set sleep time has expired the clock radio will automatically power o.
RADIO
Radio Reception
Adjust the position of the FM Antenna to improve FM radio reception. An AM antenna is built into the clock radio.
To improve AM radio reception, adjust the position of the clock radio.
Tuning the AM or FM Radio
1. Power on the radio and press the Power button again to switch between the AM and FM radio mode.
2. Press the Tunning ± buttons to nd the desired radio frequency.
3. Press the Volume ± buttons to adjust the volume of the radio.
Saving a Station as a Preset
1. With the radio on, tune to your desired frequency, press and hold the Preset/Clock button until the screen ashes.
2. Press the Tunning ± buttons to choose the desired preset station, 1 though 10.
3. Press the Preset/Clock button again to set the frequency to that preset station.
4. The unit will store 10 FM and 10 AM radio station presets. Once set, press the Preset/Clock button to cycle through
your preset stations.
ALARM
Setting the Alarm
1. In o mode, press the AL1 or AL2 buttons to set Alarm 1 or Alarm 2.
2. The screeen will ash and display the time the alarm is set to go o. Press the Hour and Minute buttons to set the
desired time. Note the PM indicator.
3. Press the Al1 or Al2 buttons repeatedly to switch between Radio, Buzzer or o. Wait for the display to stop ashing.
4. Once the set alarm time is reached, the alarm will sound. Press the Power button to turn the alarm o until the set alarm
time is reached again.
5. To set the other alarm, follow the above steps and choose the alarm not currently set.
Snooze and Alarm Reset
After the alarm sounds:
Press the Snooze button to delay the alarm for an additional 9 minutes.
OR
Press the Power button to turn the alarm o until the set alarm time is reached again.
INTERNATIONAL SUPPORT
To download this User’s Guide in
English, Spanish, or French, or to get
answers to frequently asked questions,
visit the support section at:
www.gpx.com
For Warranty Information and the most up-to-date version of this User’s Guide, go to www.gpx.com
Customer Service: 1-888-999-4215 | Email Support: prodinfo@dpiinc.com | Email Parts: partsinfo@dpiinc.com
Copyright © 2013 Digital Products International (DPI, Inc.) All other trademarks appearing herein are the property of their respective owners.
Specications are subject to change without notice.
Pour télécharger ce guide de
l’utilisateur en anglais, espagnol ou
français, ou pour obtenir des réponses
à des questions fréquemment posées,
consultez la rubrique d’assistance sur:
www.gpx.com
Para descargar este Manual del
Usuario en inglés, español y francés, o
para obtener respuestas a preguntas
frecuentes, visite la sección de apoyo
en: www.gpx.com
Loading...