Gold Medal 2626 Installation Manual

Karmel Baby

Instruction Manual

Model No. 2626, 2626EX

Part No. 17027

10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA

Karmel Baby Model No. 2626, 2626EX

SAFETY PRECAUTIONS

Page 2

gmpopcorn.com

Paddles in Correct

Karmel Baby Model No. 2626, 2626EX

INSTALLATION INSTRUCTIONS

Inspection of Shipment

After unpacking, check thoroughly for any damage which may have occurred in transit. Claims
should be filed immediately with the transportation company. The warranty does not cover
damage that occurs in transit, or damage caused by abuse, or consequential damage due to the
operation of this machine, since it is beyond our control.

Setup

1. Remove all packaging and tape before starting operation.

2. Prior to operation, rotate the top paddle into the mixing position and fix into place with

the wing bolt provided (see illustration below).

Wing Bolts

Mixing Position

Page 3

gmpopcorn.com

Stamped Aluminum

2.5 Gallon Bucket

Karmel Baby Model No. 2626, 2626EX

Accessories Included with Your Machine

• Stamped Alum Scoop

• 2.5 Gallon Bucket

• Bowl Scraper

• 2 Cup Acrylic Measure

Scoop

2 Cup Acrylic Measure

Bowl Scraper

Page 4

gmpopcorn.com

Karmel Baby Model No. 2626, 2626EX

Electrical Requirements

The following power supply must be provided:

2626: 120 Volts, 1720 Watts, 60 Hertz.
2626EX: 230 Volts, 1720 Watts, 50 Hertz

DANGER

Machine must be properly grounded to prevent electrical
shock to personnel. Failure to do so could result in serious
injury, or death.

Do NOT immerse any part of this equipment in water.
Do NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from

moisture.
Always unplug the equipment before cleaning or servicing.

Your electrician must furnish sufficient power for proper machine operation. We recommend
this equipment be on a dedicated and protected circuit. Failure to wire properly will void the
warranty and may result in damage to the machine. It is Gold Medal Products Co.’s recommendation
that this machine be plugged directly into a wall outlet. The use of extension cords is not
recommended due to safety concerns, and may cause sacrificed and/or reduced performance.

Before You Plug In Machine

1. Make sure all machine switches are in the OFF position before plugging the equipment

into the receptacle.

2. Make sure the wall outlet can accept the grounded plugs (where applicable) on the

power supply cord.

3. The wall outlet must have the proper polarity. If in doubt, have a competent

electrician inspect the outlet and correct if necessary.

4. DO NOT use a grounded to un-grounded receptacle adapter.

5. Install the unit in a level position.

Page 5

gmpopcorn.com

Karmel Baby Model No. 2626, 2626EX

OPERATING INSTRUCTIONS

Controls and Their Functions

HEAT/MOTOR SWITCH

This rocker switch in the “ON” position energizes the heating elements in the bottom of
the kettle, and the motor will also turn for 15 seconds of every minute.

Note: It is normal for the motor to stop for 45 seconds of every minute.

MOTOR SWITCH

With this rocker switch in the “ON” position, the agitator motor will run continuously.

Note: The main function of this switch is for mixing the product/popcorn at the

end of the cooking cycle with the kettle in the tilt position, and it is used for
“cleaning mode”.

HEAT CONTROL

The machine comes from the factory preset for a product cook temperature of 280°F for
Corn Treat machines. If more or less heat is required, remove the silver hole plug located
on the front panel of the control box. This will allow you to access the heat control
adjustment potentiometer. Turn the potentiometer slightly clockwise to increase the
temperature, and counter-clockwise to decrease the temperature.

To Calibrate the Heat Control for a 280°F Product Cook Temperature: Fill the mixing
bowl with a one inch depth of corn oil. Use an accurate thermometer to measure the
temperature of the oil in the mixing bowl. Stir the oil while it heats. When the oil reaches
310°F slowly turn the potentiometer counter clockwise until the buzzer sounds. If the
buzzer sounds before the temperature reaches 310°F turn the potentiometer clockwise
until the buzzer stops and continue to turn an additional 1/8 of turn.

Note: The sound of the buzzer signals kettle heat shut-off.

Kettle Dump Handle

This lever tilts the kettle from the upright cook position to the mix position or the dump
position.

Kettle Stop Lever

This lever stops the kettle in the mix position or in the dump position.

Page 6

gmpopcorn.com

H

eat/Motor

Motor Switch

Heat Control

Kettle Dump

Kettle Stop Lever

Karmel Baby Model No. 2626, 2626EX

Handle

Switch

Instructions for Making Carmel Corn

1. Always remember to leave the lid on the kettle during the first part of the batch. Once

steam starts to “roll-up” from underneath the lid, then carefully remove the lid for the
remainder of the cooking cycle.

2. Turn the Heat/Motor switch "ON" (do not turn on the Motor switch).

3. Add 6 oz. of water and one package of Gold Medal 2157 2.5 gal Caramel Complete Mix.

4. Turn the Motor switch "ON" and mix for approximately one minute. Turn the Motor

switch "OFF". (With the Heat/Motor switch "ON", the motor will run for 15 seconds
every minute.)

5. Allow the mix to cook until the buzzer sounds at 280°F product temperature.

6. Turn the Heat/Motor switch "OFF".

7. Turn the Motor switch "ON".

8. Add two and a half gallons of pre-popped corn.

9. Allow the corn to mix for approximately ten (10) seconds with the kettle in the upright

position.

10. Move the kettle to the mix position and mix the popcorn until it is thoroughly coated.

11. Dump the caramel corn into the cooling pan.

12. After dumping caramel corn, turn Motor switch “OFF”.

Page 7

gmpopcorn.com