Goldline AQL-SPASIDE-RF Installation And Operation Manual

Aqua LogicAqua Logic

Aqua LogicAqua Logic

Aqua Logic

Spa-side Remote

Installation/Operation Manual

for model

AQL-SPASIDE-RF

LDLINE

CONTROLS INC.

G

North Kingstown, RI USA

www.goldlinecontrols.com

®

Compatibility

This product is compatible with all Aqua Logic controls operating with software revi­sion r1.10 or higher . T o verify the software level of your Aqua Logic control, press the
Menu button (possibly multiple times) until “Diagnostic Menu” is displayed. Next,
press the “>” or “<“ keys (possibly mulitple times) until the main and display soft­ware revision levels are displayed (the “main” rev should be r1.10 or higher).

If the software revision level is less than r1.10 contact the Goldline T echnical Service
Dept. from Monday through Friday , 8AM to 8PM Eastern at 888-921-7665 for infor­mation on upgrades.

Installation

1. Batteries are installed at the factory: There is no need to open the spa-side

unit.

2. Base Receiver required: For operation of the spa-side remote, the Aqua Logic

control unit must have a base receiver (AQL-BASE-RF) installed. The receiver
allows the Aqua Logic control until to communicate with the spa-side remote.

3. T each the unique Aqua Logic ID code: The base receiver attached to the Aqua

Logic control unit has a unique ID code that ensures that your unit will not affect
other systems in the neighborhood, and likewise, their remote will not affect
your system. To teach the ID code to the spa-side remote unit:

a. On any Aqua Logic display/keypad unit

press the “Menu” button (possibly multiple
times) until “Settings Menu” is displayed.

b. Press “<“ or “>” (again, possibly multiple

times) until “T each W ireless” is displayed.

c. Press the “+” button to start the teaching

process.

d. Press and hold any button on the spa-side

remote for 4 seconds. At this point the LED
indicator on the spa-side remote should flash
3 times and the Aqua Logic display should
say “Teach Wireless, Successful”. If the
LED indicator does not flash, then refer to
the Troubleshooting section of this manual
for additional information.

4. Apply labels: Aqua Logic PS series of control allow each output (e.g. AUX1) to

be re-named to what is actually being controlled. The spa-side remote comes
with a sheet of name labels—simply peel the appropriate label off the sheet and
apply to the appropriate set of buttons on the spa-side remote.

5. Installation is complete: you can now use the spa-side wireless remote.

Settings

Menu

Teach Wireless:

+ to start

Teach Wireless:

Sucessful

Press and hold

wireless button

1

Operation

The spa-side remote communicates with the base receiver on the Aqua Logic control
unit using RF (radio frequency) technology . When you push a button on the spa-side
remote, it sends a command and flashes the LED indicator once. After the spa-side
remote receives a confirmation from the Aqua Logic base the receiver, the LED indi­cator on the spa-side remote flashes a 2nd time. Thus, 2 LED flashes are your confir­mation that your command has been successfully transmitted to the Aqua Logic con­trol unit. If the LED doesn’t flash at all or else just flashes once after you’ve pushed
a button, refer to the T roubleshooting section for assistance in resolving these prob­lems.

Valves POOL/SP A These buttons will allow you to select either pool or spa opera-

tion. You can not select spa spillover operation from the spa­side remote.

Filter ON/OFF The ON/OFF buttons allow manual operation that will

override any automatic control settings (e.g. timeclock). The
manual setting will remain active until the next scheduled
automatic turn on/off event. There are some exceptions:

If the heater is operating and the heater cooldown function is
enabled, then pressing the OFF button will turn off the heater
and the pump will run for another 15 minutes to allow the
heater to cooldown before automatically turning off

If the freeze protection feature is enabled and the air tempera­ture is below 38°F, then the pump will remain on to ensure that
the pipes do not freeze.

2

LDLINE

CONTROLS INC.

G

POOL SPA

ON OFF

ON OFF

ON OFF

ON OFF

ON OFF

VALVES

FILTER

HEATER

LIGHTS

AUX1

AUX2