Goldine Controls AQL-WW-RF-PS-4, AQL-WW-RF-PS-8, AQL-Tx-RF-PS-4, AQL-Tx-RF-PS-8, AQL-Tx-RF-PS-16 User Manual

Wireless Remote Display

for

Aqua LogicAqua Logic

Aqua Logic

Aqua LogicAqua Logic

Automation and Chlorination

wall mount model

table top model

Installation/Operation Manual

Wall Mount models

Table Top models

C

LD

ON

TROLS

G

for models

AQL-WW-RF-PS-4
AQL-WW-RF-PS-8

AQL-WW-RF-PS-16

&
AQL-Tx-RF-PS-4
AQL-Tx-RF-PS-8

AQL-Tx-RF-PS-16

LINE

INC

.

www.goldlinecontrols.com
888-921-7665

Compatibility

This product is compatible with all Aqua Logic controls operating with software
revision r2.00 or higher and Base Receivers with software revision r1.20 or higher. To
verify the software level of your Aqua Logic control, press the Menu button (possi­bly multiple times) until "Diagnostic Menu" is displayed. Press the ">" or "<" keys
(possibly multiple times) until the main software revision level is displayed (the revi­sion should be 2.00 or higher). Next, press the ">" key (possibly multiple times) until
the "RF Base" revision level is shown (the revision should be 1.20 or higher).

If the software revision level is less than those specified above, contact the Goldline
T echnical Service Dept. from Monday through Friday, 8AM to 8PM Eastern at 888­921-7665 for information on upgrades.

Installation

Installation - AQL-WW-RF-PS-x Wall Mount models

1. Base Receiver required: For operation of the AQL-WW-RF-PS-x, the Aqua

Logic control unit must have a base receiver (AQL-BASE-RF) installed. The
receiver also allows the Aqua Logic control unit to communicate with an op­tional spa-side remote.

2. Select Location: There are several considerations in choosing the location for

the wireless remote display/keypad:

Protected from the weather: The wireless remote display/keypad must be
mounted indoors or in a weather protected area (rain should never hit the
wireless remote display/keypad). The wireless remote display/keypad is
designed to mount onto a standard electrical utility box (same size as used
for a triple light switch) or can be mounted directly onto any wall surface.

Within range of Base Receiver: The wireless remote display/keypad must
be installed within 200 ft. (assuming the signal will have to travel through
walls) or 400 ft. (line of sight) from the Base Receiver which is typically
mounted on the Aqua Logic main control unit at the pool equipment pad.
The Base Receiver can also be mounted up to 500 ft. away from the main
control unit to shorten the distance between it and any wireless remote. See
the "Remote Mounting of the Base Receiver" section of the Base Receiver
manual for more details.

Near 120V wall outlet: The wireless remote display/keypad uses a plug-in
power supply with a 6 ft. cable.

3. Mount on wall: The wireless remote display/keypad must be mounted indoors

or in a weather protected area (rain should never hit the display/keypad). Refer
to the diagram on the following page.

a. Remove the wireless remote display/keypad baseplate from the cover by

lifting up on the cover at the lower end of the keypad.

b. Thread the wall mount power supply’s output connector from behind and

through the opening in the left side of the baseplate.

c. Screw the baseplate in the desired position (screws supplied by installer).

1

d. Plug the power supply’s output connector into the mating connector on the

back of the wireless remote display/keypad.
e. Reattach the wireless remote display/keypad to the baseplate.
f. Plug the power supply into a 120VAC outlet.

Wireless Remot e

Display unit

Pull up on bottom edge

to remove cover

Installation - AQL-Tx-RF-PS-x Table T op models

1. Base Receiver required: For operation of the AQL-Tx-RF-PS-x, the Aqua Logic

control unit must have a base receiver (AQL-BASE-RF) installed. The receiver
also allows the Aqua Logic control unit to communicate with an optional spa­side remote.

2. Select Location: Because the AQL-Tx-RF-PS-x is battery operated and de-

signed to be portable, there are no power supply or mounting concerns like the
Wall Mount units. The Table Top units are intended to be used in the normal
living space, with these considerations:

Protected from the weather: The wireless remote display/keypad should be

used indoors or in a weather protected area (rain should never hit the wire-

less remote display/keypad). Understand that areas that protect the unit

from rain, may still allow condensing humidity (dew, mist, fog, etc.) which

can damage the AQL-Tx-RF-PS-x over time. Because the unit is portable and

may be used in different areas around the pool and home, it's important to

understand that it is NOT water resistant and can be easily damaged if used

in the wrong manner.

Within range of Base Receiver: The wireless remote display/keypad must

be used within 200 ft. (assuming the signal will have to travel through walls)

or 400 ft. (line of sight) from the Base Receiver which is typically mounted on

2

the Aqua Logic main control unit at the pool equipment pad. The Base
Receiver can also be mounted up to 500 ft. away from the main control unit to
shorten the distance between it and any wireless remote. See the "Remote
Mounting of the Base Receiver" section of the Base Receiver manual for
more details.

2. Powering the AQL-Tx-RF-PS-x: The AQL-Tx-RF-PS-x uses a rechar geable

built-in battery pack which will require an initial charge when you first receive
the unit. Charge the unit for at least 15 hours before attempting to use it without
the charger. Note that the AQL-Tx-RF-PS-x can be used normally while con­nected to the charger.

Charging the battery:

Plug the included wall mount charger into a standard 120VAC wall outlet,
away from the pool area. It is not recommended that you use an extension
cord with this product. Plug the power connector into the rear of the AQL­Tx-RF-PS-x. Charge for 15 hours. A fully charged battery will provide over
400 one-minute uses under typical conditions.

About battery power:

When the charger is not plugged into the AQL-Tx-RF-x, the unit uses bat­tery power and will take steps to extend battery life. After one minute of no
button presses by the user, the unit will show a brief display and will go into
"sleep" mode (pg. 5). T o wake it up, simply press any button on the keypad.
The button press will not perform any function except waking the unit. Once
awake, any subsequent button presses will perform their normal functions.

When the charger is plugged in, the unit uses wall power while it also charges
the batteries. It will always be "awake", as long as it's plugged into the
charger.

Note that the batteries will slowly lose charge if the unit is not plugged into
the wall, even if it is not used. The batteries will need to be charged every 1

-2 months, depending on usage.
The AQL-Tx-RF-PS-x will display a series of information about its status and

the status of the battery. Refer to the "Operation" section of this manual for
an explanation of each of these displays.

NOTE: The built-in NiCad battery pack is available only through Goldline
and should offer at least 5 years of service, depending upon use. If the
battery pack needs to be replaced, contact Goldline Customer Service.

3