Goldine Controls AQL-PS-4, AQL-PS-8, AQL-PS-16 Operation Manual

Aqua LogicAqua Logic

Aqua Logic

Aqua LogicAqua Logic

Automation and Chlorination

G

ON

C

(actuators, cell & remote display not included - order separately)

Operation Manual

LD

TROLS

for models

AQL-PS-4
AQL-PS-8

AQL-PS-16

LINE

INC

.

www.goldlinecontrols.com
888-921-7665

IMPORTANT SAFETY INSTRUCTIONS

When using this electrical equipment, basic safety precautions should always be
followed, including the following:

•

•

•

•

• A green colored terminal marked “Earth Ground” is located inside the wiring

• One bonding lug for US models (two for Canadian models) is provided on the

READ AND FOLLOW ALL INSTRUCTIONS

WARNING: Disconnect all AC power during installation.

!

W ARNING: Water in excess of 100 degrees Fahrenheit may be

!

hazardous to your health.

W ARNING: To reduce the risk of injury , do not permit children to

!

use this product unless they are closely supervised at all times.

compartment. To reduce the risk of electric shock, this terminal must be
connected to the grounding means provided in the electric supply service
panel with a continuous copper wire equivalent in size to the circuit conductors
supplying the equipment.

external surface. To reduce the risk of electric shock, connect the local
common bonding grid in the area of the swimming pool, spa, or hot tub to
these terminals with an insulated or bare copper conductor not smaller than 8
AWG US / 6 AWG Canada.

• All field installed metal components such as rails, ladders, drains, or other
similar hardware within 3 meters of the pool, spa or hot tub shall be bonded to
the equipment grounding bus with copper conductors not smaller than 8 A WG
US / 6 AWG Canada.

• SAVE THESE INSTRUCTIONS

Table of Contents

System Overview Block Diagram....................................................................... 1

Automation............................................................................. 1

Chlorination............................................................................ 2

Default Display ...................................................................... 2

Manual System Output Names........................................................................ 3

Operation Filter Pump............................................................................. 3

Lights and Aux Outputs.......................................................... 4

Pool/Sp a Valves..................................................................... 4

Heaters................................................................................... 4

System Off............................................................................. 4

Service................................................................................... 5

Automatic System Using the Programming Buttons.......................................... 6

Operation Programming Menu Flow Chart........................................... 7

(Programming) Settings Menu........................................................................ 8

Timers Menu.......................................................................... 1 1

Configuration Menu............................................................... 14

Quick “How To” Operate the Sp a - Manually.................................................. 23

Guide Operate the Sp a - Automatically.......................................... 23

Set the Heater T emperature................................................. 23

Set the Chlorinator Output ................................................... 23

St art/Stop Superchlorination................................................ 24

Program a T imeclock............................................................ 24

Program a Countdown Timer............................................... 24

Enter/Exit Service Mode....................................................... 25

Chlorinator Operation/ Saturation Index..................................................................... 26

Water Chemistry Salt Level................................................................................ 27

Type of Salt............................................................................ 27

How to Add or Remove Salt................................................. 27

System Maintenance Servicing and Cleaning the Aqua Logic Cell...................... 30

Winterizing.............................................................................. 30

Spring S tartup........................................................................ 30

Troubleshooting & Service Mode ....................................................................... 31

Diagnostic Information Check System Indicator ........................................................ 31

Diagnostic Menu................................................................... 32

Chlorinator Diagnostics........................................................ 32

Instant Salt.............................................................................. 32

Flow Switch............................................................................ 32

Cell, Water , Air, Solar Temperature...................................... 33

Software Revision................................................................. 33

Warranty Aqua Logic Warranty............................................................. 35

System Overview

A

A

The Aqua Logic is a multifunction pool controller used to fully manage your pool/spa system. The Aqua
Logic can control pumps, valves, lighting, heaters, and chlorination. Although the Aqua Logic is easy to
use, it is important to completely read through this operating manual before attempting to operate the
control.

LDLINE

G

CONTROL S INC.

POOL SPA

Optional Wireless

Spaside Remote

ON OFF

ON OFF

ON OFF

ON OFF

ON OFF

VALVES

FILTER

HEATER

LIGHTS

AUX1

AUX2

Optional Wireless

Remote Display

Keypad

Optional Wired

Remote Display

Keypad

(maximum of three)

T em perature

Sensors

Water

Air

Solar

Chlorinator
Flow Switch

Circuit Breaker

Subpanel

INPUT

240 VAC

Power

Optional

Wireless Base

Receiver

PS-4 (-8, -16) MAIN UNIT

Main Display

Keypad

OUTPUT

Filter Pump
Lights

(2 for PS-4)

Aux

(6 for PS-8, PS-16)

Pool/Spa Suction &
Return Valves

General Purpose
Valves (2)

Heaters (2)
Chlorina to r Cel l

OUTPUT

120/240V
Relays

24V Valve

ctuators

120/240V

Aux (8)

EXPANSION UNIT

Relays

(used with PS-16 only)

240 VAC

Power

General Purpose
Valves (4)

Circuit Breaker

Subpanel

24V Valve

ctuators

NOTE: This manual assumes that the Aqua Logic has been wired and configured according to the Instal­lation Manual. Aspects of the Aqua Logic that pertain to system setup are not covered in this manual.

Automation

The AQL-PS-4 (-8, -16) can control up to 4 (8, 16) high voltage (120/240V) pieces of equipment, up to
4 (8 for the PS-16) automatic valve actuators, and 2 conventional heaters plus a solar heater. Both manual
and automatic (programmed) operation are available. All of the control functions can be programmed at a
display/keypad which is part of the main unit (typically located near the pool equipment) or at one or more
remote display/keypads.

1

Chlorination

With the use of the optional AQL-CL chlorination kit, the Aqua Logic is also an automatic chlorine genera­tion system for pool and/or spa sanitization. If enabled (see Configuration Menu), this operation requires
a low concentration of salt (sodium chloride) in the pool/spa water. The Aqua Logic automatically con­verts the salt into free chlorine which kills bacteria and algae in the pool/spa. Chlorine will revert back to
sodium chloride after killing bacteria. These reactions will continuously recycle, virtually eliminating the
need to add sanitizing chemicals to your pool/spa. The only time you may need to add more salt to the
pool/spa is when water is replenished due to backwashing, draining, or splashing (not evaporation).

The Aqua Logic is designed to handle the purification needs of most residential swimming pools up to
40,000 gallons (150,000 liters), or the needs of most commercial pools up to 25,000 gallons (95,000
liters). Check local codes for other restrictions. The actual amount of chlorination required to properly
sanitize a pool varies due to bather load, rainfall, temperature, and the pool’s cleanliness.

Default Display

Turn power on at the main panel and turn the Aqua Logic control power circuit breaker on. The keypad
will show the default display . The default display alternates between the day/time, air and pool (or spa)
temperature, pool/spa sanitizer setting, and salt level. Under certain unusual circumstances, additional
displays may be added to the default menu to inform you about system operation. The Aqua Logic will
automatically scroll through all of the default menu displays or you can press “<” or “>” to manually scroll.

Optional Remote Display/keypad shown--the display keypad on the

main control unit will have a “Service” button in the upper left

corner instead of the “System Off” button.

2

Manual System Operation

While the main objective of the Aqua Logic is to automate the operation of your pool/spa system, there
may be certain times when you want to override the automatic operation and control the equipment manu­ally . T o operate the pool equipment manually while keeping the automation active, perform the following
procedures. Note that if you turn a relay on manually , it will remain on until either you turn it off manually ,
or the next time the programmed automatic operation would normally turn that relay off. Example: the
filter pump is programmed to run from 9:00A to 5:00P daily . If you turn the filter pump on manually at
8:00PM, it will run continuously until the next day at 5:00PM at which time it will turn off and follow the
normal program from then on. Manually turning off a relay works in a similar fashion.

Display

System Off (remote displays)

or

Service (main unit display)

Menu and Navigation Buttons

Check System LED

Aux1 - Aux6

(On/Off)

PS-8
Display

Valve4 or Heater2

(See Configuration Menu)

Output Names

The Aqua Logic is shipped from the factory with each output labeled with a generic name (e.g. AUX1,
V AL VE3, etc.). One of the features in the software (see Configuration Menu, page 14) is that each output
can be assigned a new name that is more descriptive of the equipment being controlled. This makes it much
easier to operate all of the equipment on your pool without having to memorize what each output controls.
Insert name labels are also provided to be placed next to each display pushbutton. Since there is no way
to know how your particular system is configured, this manual will use the original generic names for each
output.

Filter Pump

Single Speed Filter Pump: If the pump is currently off, press the “FIL TER” button to turn on the pump.
Pressing the “FIL TER” button again will turn off the pump. However, if there is a heater in the system, and
it is operating, and the “Heater Cooldown” feature is enabled (Configuration Menu) then: when you press
the “FIL TER” button to turn off the filter , only the heater will turn off, the Filter LED will flash and the
display will indicate “Heater Cooldown”. At this point the filter pump will automatically turn of f after 15
minutes of heater cooldown operation. If you want to override the heater cooldown, simply press the
FIL TER button again to turn off the filter pump.

T wo Speed Filter Pump: If the pump is currently off, simply press the “FIL TER” button to turn on high
speed operation of the filter pump. The “FIL TER” LED will illuminate continuously . Pressing the “FIL­TER” button again will switch to low speed operation and the “FIL TER” LED will flash. If you attempt to
switch to low speed shortly after turning on high speed the filter pump will automatically remain in high
speed for 3 minutes before switching to low speed to allow the pump to prime and establish normal water
flow .

3

Freeze Pr otection: This function protects the pool, plumbing, and equipment against freeze damage. If
Freeze Protection is enabled and the AIR temperature sensor falls below 38°F, the Aqua Logic will turn on
the aux relay to circulate the water. IMPOR T ANT : this only enables operation of the AUX output during
freeze--see the “Filter Pump Config.” menu to enable freeze protection for the main circulation system.

Lights and Aux Outputs

Manual operation of all relays (AUX1 and AUX2 for a PS-4 model, AUX1 - AUX6 for a PS-8 model, or
AUX1 - AUX14 for a PS-16 model) is identical. Assuming that the relay is currently off, simply press the
appropriate button to turn on the relay . If the relay does not turn on, it probably is due to the “interlock”
feature (which was set up in the Configuration Menu) being activated that requires the filter pump to be
running and the valves to be in the pool-only position. This protects pumps and other equipment from
possible damage. If the controlled output is on, pressing the appropriate button again will turn off the relay .
Manual turn off is disabled if the “Freeze Protection” feature is enabled and the air temperature is less than
the selected freeze temperature threshold.

Pool/Spa V alves

Pool-only or spa-only systems: The POOL/SP A/SPILLOVER button has no function.
Standar d Pool and Spa systems without spa spillover: In pool-only mode (“POOL” LED illuminated),

press the “POOL/SP A/SPILLOVER” button to switch to spa-only operation (“SP A” LED illuminated).
Pressing the “POOL/SP A/SPILLOVER” button again will switch back to pool-only . Note that the filter
pump will turn off while the pool/spa valves are turning.

Standar d Pool and Spa systems with spa spillover: When currently in the pool-only mode (“POOL”
LED illuminated), press the “POOL/SP A/SPILLOVER” button to switch to spa-only operation (“SP A”
LED illuminated). Press the button again to switch to spa spillover operation (“SPILLOVER” LED
illuminated). Pressing the “POOL/SP A/SPILLOVER” button again will switch back to pool-only mode.
Note that the filter pump will turn off while the pool/spa valves are turning.

Dual Equipment Pool and Spa systems without spa spillover: The POOL/SP A/SPILLOVER button
has no function. The “POOL” LED will always be illuminated.

Dual Equipment Pool and Spa systems with spa spillover: When currently in the separate Pool and
Spa loops mode (“POOL” LED illuminated) and the Spa Filter is off, press the POOL/SP A/SPILLOVER
button to switch to spa spillover operation (“SPILLOVER” LED illuminated). Press the POOL/SP A/
SPILLOVER button again to return to the separate Pool and Spa loops mode of operation. Note that the
Pool Filter pump will shut off while the pool/spa return valve is turning. The system will automatically
switch out of spillover whenever the spa filter pump is turned on.

Note: For Dual Equipment Pool and Spa systems, there is no Spa Only mode.

Heaters

This description applies to Heater1 and to Heater2, if programmed (note that the function of the V alve4
button changes to Heater2 when Heater2 is enabled). Pressing the “HEA TER” button causes the Aqua
Logic to switch the heater control output between a “forced off” state and a normal, automatic thermo­static control operating state.

System Off

Each remote display/keypad has a red “SYSTEM OFF” button on the upper left corner of the keypad.
Pressing this button will turn all outputs off and they will remain off, regardless of any programmed control
logic, until either the “SYSTEM OFF” button (on any remote display/keypad) is pressed again or the
“SER VICE” button is pressed on the display/keypad at the main unit. The red “SYSTEM OFF” LED will
illuminate to indicate that all outputs and being forced off.

4

W ARNING: pr essing the “SYSTEM OFF” button overrides any programmed freeze pro-

!

tection and may cause damage to your system in freezing conditions.

Service

The main unit keypad has a “SER VICE” key . This button is used primarily during servicing of the pool
equipment. If you want to completely disable the automatic operation and operate the system manually ,
you can put the system into Service or Service-Timed mode by pressing the “SER VICE” button. Pressing
the “SER VICE” button once will switch the system into service mode which means that all automatic
functions are disabled, and the remote display/keypads are disabled (except for manual turn off for emer­gencies). The red “SER VICE” LED will be illuminated and the Aqua Logic will remain in this mode of
operation until manually taken out of service mode.

Pressing the “SER VICE” button again will cause the Aqua Logic to switch to service-timed mode which is
very similar to service mode, except that the Aqua Logic will automatically return to normal operation after
3 hours. During service timed operation, the “SER VICE” LED will flash and the time remaining will be
displayed on the remote display/keypad(s).

Pressing the “SER VICE” button again, will return the Aqua Logic to normal (automatic) operation.
See T roubleshooting/Diagnostic Information (page 31) for more information about the service modes.

5

Automatic System Operation

>

>

>

>

The Aqua Logic controls most of your pool equipment automatically in order to minimize the time spent
working on your pool. Most of the pool equipment can be programmed to operate on a timeclock basis.
In addition, the desired pool and spa temperatures and pool and spa chlorinator settings can be pro­grammed. This section will guide you on how to program the automatic operation for each function.

The programming of automatic functions can be performed at either the main display/keypad located at the
pool equipment pad or the in-home remote display/keypad.

Using the programming buttons

There are 5 buttons on each keypad that are used for programming (refer to diagram).

MENU

Button

+

MENU

<

>

Select Desired Menu

and Buttons

+

Adjust

There are 4 steps to programming any function:

1.

2.

3.

Menu

+

Press the “MENU” button to get to the desired menu. Multiple pushes of the
button will rotate through all 5 menus and return to the starting point.

Press either key to scroll through the various items in the selected menu. Multiple
pushes of the button will rotate through all menu items and return to the starting
point. Only menu items that are applicable to your pool will appear. (Example: if
you don’t have a spa, then no spa related menu items will appear).

Once a menu item has been selected above, the current setting/selection will ap­pear (flashing) on the display . Use the “+” and/or “-” keys to change this selec­tion. Sometimes “+” and “-“ will adjust a value up or down (example: heater
temperature setting or timeclock on/off time) or , in other cases the “+” and “-“
may toggle between 2 options (example: turning superchlorination ON or OFF).

<

and Buttons

>

Select Items from

a Menu

4.

Menu

After you have adjusted the item to the desired value, simply move on to the next
menu item to “lock in” your new setting. The Aqua Logic memory will maintain
the setting, even if power is removed for an extended period.

6

Programming Menu Flowchart

default menu day and time

settings menu spa heater1 temp (off, 65ºF-104ºF)

timers menu filter pump -- all days (or) filter pump -- weekends

PS-4 only

diagnostic menu chlorinator diagnostics

configuration menu chlor config.

PS-4 only

air/water temperature

chlorinator setting

salt level

pool heater1 temp (off, 65ºF-104ºF)
spa heater2 temp (off, 65ºF-104ºF)
pool heater2 temp (off, 65ºF-104ºF)

spa solar temp (off, 65ºF-104ºF)

pool solar temp (off, 65ºF-104ºF)

superchlorinate (on/off)

spa chlorinator setting (0-100%)

pool chlorinator setting (0-100%)

day and time

display light (always on/60 sec)

teach wireless remote

wireless channel

low speed -- all days (or) low speed -- weekends

spa -- all days (or) spa -- weekends

lights -- all days (or) lights -- weekends (or) lights -- countdown

}

}

aux1 -- all days (or) aux1 -- weekends (or) aux1-- countdown

aux2 -- all days (or) aux2 -- weekends (or) aux2-- countdown

valve3 -- all days (or) valve3 -- weekends

valve4 -- all days (or) valve4 -- weekends

super chlorinate hours (1-96)

instant salt
flow switch

cell temperature sensor

water sensor

air sensor

solar sensor

main software revision

display software revision

expansion unit software revision

RF base software revision

pool/spa config.

filter config.

heater1 config

heater2 config

solar config.

lights config

aux1 config

aux2 config

valve3 config

valve4 config

all timeclocks (7 or 2/5 day)

time format (12 or 24 hr)

units (english/metric)

reset config to default

denotes conditional items

filter pump --weekdays

low speed --weekdays

spa --weekdays

lights -- weekdays

aux1 -- weekdays

aux2 -- weekdays

valve3 -- weekdays

valve4 -- weekdays

chlorinator (enabled/disabled)

display salt/minerals

pool only / spa only / pool & spa-std / pool & spa-dual

function (manual on/off, timeclock, countdown timer)

function (manual on/off, timeclock, countdown timer, solar, low speed filter pump)

function (manual on/off, timeclock, countdown timer, solar, low speed filter pump)

function (manual on/off, timeclock, countdown timer, solar, in-floor cleaner)

function (manual on/off, timeclock, countdown timer, solar, in-floor cleaner)

spa countdn

spillover (enabled/disabled)

filter operation (pool only/spa spillover)

v1=aux1 v2=aux2 (enabled/disabled)

filter name

1 speed, 2 speed

freeze protection (enabled/disabled)

freeze temp

heater1 (enabled/disabled)

heater1 name

heater cooldown (enabled/disabled)

heater extend (enabled/disabled)

heater2 (enabled/disabled)

heater2 name

heater cooldown (enabled/disabled)

heater extend (enabled/disabled)

solar (enabled/disabled)
solar extend (enabled/disabled)
solar priority (enabled/disabled)

lights name

aux1 name

interlock (enabled/disabled)

freeze protection (enabled/disabled)

aux2 name

interlock (enabled/disabled)

freeze protection (enabled/disabled)

valve3 name

interlock (enabled/disabled)

freeze protection (enabled/disabled)

valve4 name

interlock (enabled/disabled)

freeze protection (enabled/disabled)

7

The Aqua Logic’s five menus have many items in each menu that allow you to customize the operation of
your pool/spa equipment. The chart below shows the Aqua Logic’ s five menus as well as each menu’s
specific settings.

The Default Menu is a series of informative displays (temperatures, salt levels, chlorinator settings, etc.)
with nothing to set. The Aqua Logic will automatically switch to the default menu when no keys have been
pressed for 2 minutes and will then scroll through each display .

The Settings Menu and the Timers Menu are the menus you will be using most often to adjust the operation
of your pool. The Configuration Menu is used when the system is installed and defines what equipment is
connected to each output and the operational logic that will control the equipment. This menu is normally
“locked” and should only be used by a pool professional. Details regarding the Configuration menu are
included in the Aqua Logic Installation Manual.

The “Diagnostic Menu” is primarily intended for the service technician and contains information and details
about the system operation that are helpful in troubleshooting, if problems occur.

Settings Menu

The Settings Menu allows you to set all system operating parameters except the timeclock and countdown
timers which are part of the Timers Menu.

Important: All of the displays shown below use the default generic names for each function

!

or output. The Aqua Logic allows more descriptive names to be assigned to each piece of equip­ment (refer to the section regarding the Configuration Menu for more information).

Spa Heater1

Off

not shown if Pool

and Spa-Dual is selected

Spa Heater2

102°F

not shown if Pool

and Sp a-Dual is selected

Pool Heater1

Off

Pool Heater2

85°F

Adjust the d e sired sp a temp e r a t ur e ( O ff, 65 °F, 66°F, ...1 0 3 ° F, 104°F, Off)

+

>

>

Move to previous/next menu item

Adjust the d e sired sp a temp e r a t ur e ( O ff, 65 °F, 66°F, ...1 0 3 ° F, 104°F, Off)

+

>

>

Move to previous/next menu item

The spa heater setting will only appear if the system has been setup for “spa only” or “pool
and spa” operation and the “Heater1” and/or “Heater2” control is enabled. The heater will
turn on whenever the pool/spa valves are in the “spa only” position and the filter pump is
running and the spa water temperature is less than the desired temperature setting. If you
have both solar heat and a conventional heater and the solar priority option is selected
(Configuration Menu), then the conventional heater will only operate when solar heat is
NOT available.

For Pool and Spa dual equipment operation (“Pool and Spa -Dual” selected), Spa Heater1 is
tied to the Spa Filter (AUX1).

Adjust the desired pool temperature (Off, 65°F, 66°F, . ..103°F, 104°F, Off)

+

>

>

Move to previous/next menu item
Adjust the desired pool temperature (Off, 65°F, 66°F, . ..103°F, 104°F, Off)

+

>

>

Move to previous/next menu item

The pool heater setting will only appear if the system has been setup for “pool only” or “pool
and spa” operation and the “Heater1” and/or “Heater2” control is enabled. The heater will
turn on whenever the pool/spa valves are in the “pool only” or “spa spillover” position and
the filter pump is running and the pool water temperature is less than the desired temperature
setting. If you have both solar heat and a conventional heater and the solar priority option

8

is selected (Configuration Menu), then the conventional heater will only operate when solar
heat is NOT available.

For Pool and Spa dual equipment operation (“Pool and Spa -Dual” selected), Pool Heater2 is
tied to the Pool Filter (FIL TER).

Spa Solar

102°F

Pool Solar

88°F

Super Chlorinate

Off

Adjust th e desired spa tem perature (Off, 65°F, 66°F, ...103°F, 104°F, Off)

+

>

>

Move to previous/next menu item

The spa solar setting will only appear if the system has been setup for “spa only” or “pool
and spa” operation and the solar control is enabled. The solar system will turn on whenever
the pool/spa valves are in the “spa only” position and the filter pump is running and the spa
water temperature is less than the desired temperature setting and solar heat is available.

Adjust the desired pool temperature (Off, 65°F, 66°F, ...103°F, 104°F, Off)

+

>

>

Move to previous/next menu item

The pool heater setting will only appear if the system has been setup for “pool only” or “pool
and spa” operation and the solar control is enabled. The solar system will turn on whenever
the pool/spa valves are in the “pool only” or “spa spillover” position and the filter pump is
running and the pool water temperature is less than the desired temperature setting and solar
heat is available.

Turn super chlorinate on or off

+

>

>

Move to previous/next menu item

This display only appears if the chorinator function is enabled (see Configuration Menu).
When you have an unusually high bather load, a large amount of rain, a cloudy water
condition, or any other condition that requires a large amount of chlorine to be introduced to
the pool, activate the Aqua Logic Super -Chlorinate function. The Aqua Logic will turn on
the filter pump, set the pool/spa valves to the correct position, and set the chlorine generator
to maximum output. The superchlorinate function will continue for the programmed number
of hours (see Timers/Super Chlorinate Hours below) overriding the normal filter pump timeclock
settings. At the end of the super chlorinate period, the pool will return to normal operation.

Spa Chlorinator

3%

Pool Chlorinator

60%

If you manually turn off the filter pump (using the “FIL TER” button on any display/keypad),
the super chlorinate function terminates. When you turn the filter pump back on, super
chlorinate will resume for the balance of the programmed number of hours.

+

Adjust the desired chlorinator output for spa (0,1,2,3...9,10,15,20...95,100%)

>

>

Move to previous/next menu item

This setting will appear only if the chorinator function is enabled and system has been setup
for “spa only” or “pool and spa-std”. It will determine the chlorinator output when the
system is operating in spa-only mode. The actual amount of chlorine introduced into the spa
is determined by: this setting, the amount of time the pool operates in spa-only mode, the
water temperature, and the amount of salt in the water.

Adjust the desired chlorinator output for pool (0,1,2,3...9,10,15,20...95,100%)

+

>

Move to previous/next menu item

>

9

Set Day and Time

Set Day and Time

Wednesday 10:37P

10:37P

Set Day and Time
Wednesday 37

Set Day and Time

Wednesday 10: P

This setting will appear only if the chorinator function is enabled and system has been setup
for “pool only” or “pool and spa”. It will determine the chlorinator output when the system
is operating in pool-only or spa spillover modes. The actual amount of chlorine introduced
into the pool is determined by: this setting, the amount of time the filter pump is running, the
water temperature, and the amount of salt in the water. If the filter pump is running due to the
freeze protection feature, then the chlorinator will not operate during this time.

Adjust the current day of the week

Adjust the current day of the week

+

>

>

Move to hours setting

Move to hours setting
Adjust the current hour (including AM/PM if applicable)

+

>

>

Move to minutes setting
Adjust the current minute

+

>

>

Move to previous/next menu item

Use this function to set the current day of the week and time. These values are used for all
the automatic timeclock functions of the Aqua Logic and are also displayed as part of the
default menu.

The Aqua Logic is designed to keep the clock running during power outages lasting less
than 7 days. If power has been off for longer than 7 days, then the time may have to be reset.

Display Light

On for 60 sec

Teach Wireless

+ to start

Press and hold

wireless button

Teach Wireless

Successful

Teach Wireless

NOT Successful

Teach Wireless

Base NOT Found

Toggle between Always On and On for 60 sec.

+

>

>

Move to previous/next menu item

This function controls the blue backlight on the display. If the “On for 60 seconds” option
is selected, then the backlight will automatically turn off 60 seconds after the last key is
pressed and will stay off until next time a key is pressed.

Note that the Display Light selection only applies to the display keypad that you are currently
using. Other display/keypads will not be affected. In other words, you need to individually
set this option for each display/keypad in the system.

+

Push to start process

>

>

Move to previous/next configuration menu item

Press any button on wireless remote

>

Move to previous/next configuration menu item

>

>

Move to previous/next configuration menu item

>

>

Move to previous/next configuration menu item

>

This menu will only appear if a wireless base station is connected to the Aqua Logic. Perform
this procedure each time a wireless remote control is added to the Aqua Logic system.
During this procedure the wireless remote “learns” and remembers the ID code for the
wireless base station connected to this particular Aqua Logic unit and will reject messages
with any other ID codes. If “Base NOT found” is displayed, then the Aqua Logic can not
communicate with the transmitter/receiver base station attached to the main unit. If “NOT
Successful” is displayed, then the base station did not receive a signal from the remote
control. This may be due to the distance between the Base Receiver and the remote device
being too great or may be due to interference caused by other RF equipment operating in the
neighborhood. Try using the “Change Channel” command (see next page) and then repeat
the “T each W ireless” command.

10

Wireless

Channel: 1

Confirm Change:

+ to proceed

Change the desired wireless channel (1 - 5)

+

>

If channel is changed, move to confirmation menu

>

If channel is not changed, move to previous/next menu item

+

Push to confirm the channel change

>

Move to previous/next menu item

>

Reteach all

wireless units

>

Move to previous (Teach Wireless) menu

>

This setting changes the channel to be used by the wireless base station and remote(s). If
the channel is changed and confirmed, the wireless remote will have to be re-taught. This
menu will only appear if a wireless base station is connected to the Aqua Logic.

Timers Menu

The Timers Menu allows you to set all timeclock and countdown timers which control the automatic
operation of your pool/spa system.

Each timeclock has a single on/off program per day . All of the timeclocks are setup (Configuration Menu)
either as “all days” or “weekends/weekdays”. If “weekends/weekdays” are selected, you will need to
program on times for both weekdays and weekends and off times for both weekdays and weekends, even
if you want them to be the same. All times are adjusted in 15 minute increments (9:00A, 9:15A, 9:30A,
etc.). If you program the on time equal to the off time (“10:00A to 10:00A”) the output will NEVER turn
on. If you want to disable a timeclock, you can set the on time equal to the off time and you will notice the
times disappear and the display simply shows “Off”. If, at a later time, you wish to re-activate the timeclock,
simply press either the “+” or “-“ buttons to go back to a normal timeclock programming display .

The Countdown timer is programmed in increments of 5 minutes from “0:00” to a maximum of “21:00”.
When “0:00” is programmed, the countdown timer is disabled and the output will be manually controlled.
When a countdown timer is greater than “0:00”, pressing the appropriate output button will turn the output
on and start the timer. Pressing the button again will turn the output of f or, when the programmed time has
elapsed, the output will automatically turn off.

Important: All of the displays shown below use the default generic names for each function

!

or output. The Aqua Logic allows more descriptive names to be assigned to each piece of equip­ment (refer to the section regarding the Configuration Menu for more information).

Adjust time setting

Set Day and Time

Filter T1-all

Wednesday 10:37P

or

8:30A to 4:00P

Filter T1-wkend
8:30A to 4:00P

Filter T1-wkday
8:30A to 4:00P

For one speed pumps, this is the first filter timeclock and will determine the normal hours of
filtration for the pool. For pool/spa combination systems with spillover enabled, the valves
will automatically switch to spillover mode at the start of the filtration period. For all other
systems, the valves will switch to the pool-only position. Refer to page 11 for general notes
regarding timeclock programming.

For two speed pumps, this setting will be the period of time when the pump runs at high
speed (the word “Filter T1” in the display will be replaced with “Filter Hi”). There is a
separate timeclock for the low speed operation (see below). If the high speed and low speed
periods overlap, then the pump will operate in low speed during the overlap period.

There are several reasons the filter pump may be running at times other than the timeclock
period set above. These include super-chlorination, spa operation, manual operation, heater
cooldown, freeze protection and “solar-extend”.

Adju s t tim e s

+

>

>

Move between start and stop times & to previous/next menu item
Adjust time setting

+

>

>

Move between start and stop times & to previous/next menu item
Adjust time setting

+

>

Move between start and stop times & to previous/next menu item

>

11

Set Day and Time

Filter T2-all

Wednesday 10:37P

8:30A to 4:00P

or

Filter T2-wkend
8:30A to 4:00P

Adjust time setting

Adju s t tim e s

+

>

>

Move between start and stop times & to previous/next menu item
Adjust time setting

+

>

>

Move between start and stop times & to previous/next menu item

Filter T2-wkday
8:30A to 4:00P

Set Day and Time

Wednesday 10:37P

6:00P to 9:00P

or

Spa-

6:00P to 9:00P

Spa-wkday

6:00P to 9:00P

Spa-all

wkend

Adjust time setting

+

>

Move between start and stop times & to previous/next menu item

>

For one speed pumps, this is the second filter timeclock
For two speed pumps, this timeclock will set the normal time period for filter pump low speed

operation (the word “Filter T2” in the display will be replaced with “Filter Lo”). If the filter
pump was off prior to the start of this time period, the filter pump will first turn on at high
speed for 3 minutes to prime and establish water flow. Afterwards, it will drop down to low
speed for the remainder of the programmed low speed time period. While this time clock will
override the high speed timeclock (see above), there are several reasons why the pump will
automatically switch to high speed operation during this programmed time period. These
include manual operation, spa operation, or solar heating operation. Refer to page 11 for
general notes regarding timeclock programming.

Adjust time setting

Adju s t tim e s

+

>

>

Move between start and stop times & to previous/next menu item
Adjust time setting

+

>

>

Move between start and stop times & to previous/next menu item
Adjust time setting

+

>

Move between start and stop times & to previous/next menu item

>

This menu is only available if the system has been setup for “spa only” or “pool and spa”.
During the programmed spa time, the Aqua Logic will turn on the filter pump and move the
pool/spa valves into the “spa-only” position. The heater will automatically heat the spa up
to the programmed spa temperature (see page 8). This programmed spa operation will take
precedence over all other automatic functions, only manual operation of the filter button or
pool/spa valve button will override this function. Refer to page 11 for general notes regarding
timeclock programming.

Set Day and Time

Wednesday 10:37P

8:00P to 11:00P

or

Lights-wkend

8:00P to 11:00P

Lights-wkday

8:00P to 11:00P

or

Lights-CountDn

Lights-all

0:20

If your pool has a separate jet pump or blower controlled by Aux1 and/or Aux2 , you will have
to program those separately (see below).

Adjust time setting

Adju s t tim e s

+

>

>

Move between start and stop times & to previous/next menu item
Adjust time setting

+

>

>

Move between start and stop times & to previous/next menu item
Adjust time setting

+

>

>

Move between start and stop times & to previous/next menu item

This menu will appear only if the Lights are configured for timeclock. The lights will turn on
and off at the designated times. The only override on this function is manual on/off control
by the “Lights” button. Refer to page 11 for general notes regarding timeclock programming.

Adjust time setting (Manual On/Off, 0:05, 0:10, 0:015...)

+

>

>

Move to previous/next menu item

This menu will appear only if the Lights are configured for countdown timer. This setting is
the time after you manually turn on the lights until the Aqua Logic automatically turns of f the

12

lights. You can also manually turn off the lights at an earlier time by pressing the LIGHTS
button. Refer to page 11 for general notes regarding timeclock programming.

For PS-4, Aux1 and Aux2 configurations are identical. For PS-8 models, Aux1 - Aux6 configurations are identical. For PS­16 models, Aux1 - Aux14 configurations are identical.

Adjust time setting

Set Day and Time

Aux1-all

Wednesday 10:37P

8:30A to 4:00P

Adju s t tim e s

+

>

>

Move between start and stop times & to previous/next menu item

or

Aux1-wkend

8:30A to 4:00P

Adjust time setting

+

>

Move between start and stop times & to previous/next menu item

>

Aux1-wkday

8:30A to 4:00P

Adjust time setting

+

>

Move between start and stop times & to previous/next menu item

>

This menu will appear only if the Aux1 is configured for timeclock. The Aux output will turn
on and off at the designated times. If the Aux relay is off during the programmed on time—

or

note that some pool equipment (example pressure side pool cleaner) can only be operated
when the filter pump is running and the pool/spa valves are in the pool-only position—the
Aqua Logic will keep the relay off until these other conditions are suitable for operation. If
the Aux relay is on during the programmed of f time, it may be because of freeze protection.
Also, manual operation overrides the timeclock. Refer to page 11 for general notes regarding
timeclock programming.

Aux1-CountDn

0:20

Adjust time setting (Manual On/Off, 0:05, 0:10, 0:15...)

+

>

Move to previous/next menu item

>

This menu will appear only if the Aux1 is configured for countdown timer . This setting is the
time after you manually turn on the Aux relay until the Aqua Logic automatically turns off the
relay. You can also manually turn off the relay at an earlier time by pressing the AUX1 or
AUX2 button. Refer to page 11 for general notes regarding timer programming.

NOTE: The configurations for Valve3 and Valve4 are identical. However, if Heater2 was enabled, then the Valve4
configuration will not appear (a single relay is used to implement either the Heater2 function or the Valve4 function-

-it can not do both).

Adjust time setting

Adju s t tim e s

Set Day and Time

Valve3-all

Wednesday 10:37P

8:30A to 4:00P

+

>

>

Move between start and stop times & to previous/next menu item

or

Adjust time setting

Valve3 -wke n d

8:30A to 4:00P

+

>

>

Move between start and stop times & to previous/next menu item

Valve3-wkday

8:30A to 4:00P

or

Set Day and Time

Valve3-CountDn

Wednesday 10:37P

0:20

Adjust time setting

+

>

Move between start and stop times & to previous/next menu item

>

This menu will appear only if Valve3 is configured for timeclock. The valve will rotate on and
off at the designated times. There is no manual override. Refer to page 11 for general notes
regarding timeclock programming.

Adjust time setting (Manual On/Off, 0:05, 0:10, 0:15...)

Adju s t tim e s

+

>

>

Move to previous/next menu item

This menu will appear only if the Aux1 is configured for countdown timer . This setting is the
time after you manually turn on the Aux relay until the Aqua Logic automatically turns off the
relay. You can also manually turn off the relay at an earlier time by pressing the AUX1 or
AUX2 button. Refer to page 11 for general notes regarding timer programming.

13

Super Chlorinate

A

24 hours

+

Larger pools or when you have an unusually high bather load, a large amount of rain, a
cloudy water condition, or any other condition that requires a large amount of chlorine to be
introduced to the pool, may require more hours of Superchlorination. Smaller pools require
less hours of Superchlorination.

djust Superchlorination period (1 - 96 hours)

>

>

Move to previous/next menu item

Configuration Menu

The Aqua Logic MUST BE CONFIGURED before attempting to operate. Configuration information is
entered at the keypad and “tells” the Aqua Logic what equipment is connected and how each should be
controlled.

CAUTION: When changing an existing configuration, it is important to understand how

!

the pool system operates and what specific equipment is connected to each output. Incor­rect settings in the configuration menu could lead to damaged equipment and improper
operation of the pool system.

Accessing the Configuration Menu

Configuring the Aqua Logic requires that you navigate through the Configuration Menu and input various
information. For more detailed information about using the Aqua Logic menu system, refer to the Opera­tion Manual.

To access the Configuration Menu

Configuration

Menu-Locked

Configuration

Menu-Unlocked

Menu

Press repeatedly until “Configuration Menu” is displayed

>

>

Press BOTH buttons SIMULTANEO USLY for 5 seconds to unlock

>

Move to configuration menu items

>

NOTE: The configuration menu automatically “locks” after 2 minutes of no buttons being
pressed to prevent unauthorized people from changing the control logic inadvertently and
possibly damaging the pool equipment or causing a “call back” to fix the configuration.

Configuration Menu Items

Each item needs to be programmed and may contain additional sub-menu items. Refer to the following
pages for information on programming.

Chlor. Config.

+ to view/change

Chlorinator

Enabled

Display

Salt

+

Push to access Chlorinator option

>

>

Move to previous/next configuration menu item

Toggle between Enabled and Disabled (default) Chlorina to r

+

>

>

Move to previous/next configuration menu item

Toggle between Display Salt (default) and Minerals

+

>

>

Move to previous/next configuration menu item

14

Chlorinator

If the chlorinator is enabled (requires the use of the AQL-CL chlorination kit), then the cell
and flow switch must also be installed and the Aqua Logic will automatically chlorinate both
the pool and spa according to the desired output setting (see Settings Menu in the Operation
manual). If disabled (default), then neither the cell nor flow switch need to be installed and
all displays relating to the chlorinator will be suppressed.

Display

Allows for the display of salt (default) or mineral values.

Pool/Spa Config.

+ to view/change

Pool/Spa Setup

Pool and Spa-Std

if “Pool and Spa-Std” is selected

Spa - CountDn

00:30

if “Pool and Spa-Std or Dual” is selected

Spa Spillover

Enabled

if “Pool an d Spa-Std or Dual” is
selected and if “Spa Spil lo ver” is enable d

Filter Operation

Spa Spillover

if “Pool Only” or “Spa Only” is selected

V1=Aux1, V2=Aux2

Disabled

Push to access Pool/Spa options

+

>

>

Move to previous/next configuration menu item
Rotates between Pool and Spa-Std , Pool and Spa-Dual,

+

Spa Only, and Pool Only options

>

Move to next menu item

>

+

Adjust time setting (Manual on/off, 0:05, 0:10, 0:15..., (default is 4:00))

>

Move to next menu item

>

+

Toggle between Enabled and Disabled Spa Spillover(default)

>

Move to next menu item

>

+

Toggle between Pool Only and Spa Spillover options(default)

>

Move to next menu item

>

Toggle between Enabled and Disabled (default)

+

>

Move to next menu item

>

Pool/Spa Setup

If “Pool Only” or “Spa Only” are selected, then the pool/spa valves are deactivated and
pushing the POOL/SP A button on the display/keypad will have no effect. If “Pool and Spa­Std” is selected, then the pool/spa suction and return valve actuators should be connected
to the Aqua Logic. Pressing the POOL/SPA button on the display/keypad will allow the
homeowner to alternate between pool and spa operation. If “Pool and Spa-Dual” is selected,
then only the Pool/Spa return valve actuator should be connected to the Aqua Logic.

(default)

Spa CountDn

This menu will appear only if Pool/Spa Setup is set to “Pool and Spa-Std”. This setting is the
time, after you manually switch the Pool/Spa valves to “Spa Only”, until the Aqua Logic
automatically returns the valves to their previous positions. It is programmed in increments
of 5 minutes, from “Manual On/Off” (0 minutes) to “21:00” (21 hours). The filter is forced on
during this time period.

Spa Spillover

When spa spillover is “Enabled” and “Pool and Spa-Std”, the homeowner will be able to
rotate through “Pool Only” (both suction and return valves switched to pool), “Spa Only”
(both suction and return valves switched to spa) and “Spillover” (suction valve switched to
pool and return valve switched to spa) by successive presses of the “Pool/Spa) button. For
“Pool and Spa-Dual”, only “Pool Only” and “Spillover” are available.

Filter Operation

If “Spa Spillover” is selected, the Aqua Logic will automatically switch the pool/spa suction
and return valves to the “spillover” at the start of the programmed pool filtering time period
or when the super-chlorinate function is turned on. The valves will remain in this position for

15

the remainder of the super-chlorinate period. This option is usually preferable because both
the pool and spa water will be filtered and sanitized.

If “Pool Only” is selected, then the Aqua Logic will switch the pool/spa valves to the “pool
only” position during super chlorinate. This may be desirable on some systems with in-floor
cleaners because it allows the cleaner to operate all the time the pool is being filtered and/or
the super chlorinate is running.

V1=Aux1, V2=Aux2

This menu appears only if the Pool/Spa Setup is “Pool Only” or “Spa Only”. When enabled,
V alve 1 (return) will follow the Aux1 output and Valve 2 (suction) will follow the Aux2 output.
When disabled (default), the return and suction pool/spa valves function normally.

Filter Pump Config.

+ to view/change

Filter Name

Pool Filter

Filter Pump

1 Speed

Freeze Protect

Enabled

Freeze Temp

38ºF

Push to access pump options

+

>

>

Move to previous/next configuration menu

Rotates between all available names

+

>

>

Move to next menu item
Toggle between 1-speed (default) and 2-speed options

+

>

>

Move to next menu item
Toggle between Enabled (default) and Disabled Freeze Protection

+

>

>

Move to next menu item
Adjust the desired freeze protection temperat ure (33ºF - 42ºF)

+

>

>

Move to next menu item

Filter Name

The Aqua Logic allows you to assign any one of a number of names (e.g. “Filter Pump, Pool
Filter, Spa Filter , etc.) to the filter relay . This will make the Aqua Logic more user friendly to the
homeowner when they want to control the filter equipment. A sheet of small name labels is
included with the Aqua Logic main unit and each remote display/keypad so that appropriate
pushbuttons can be labeled the same as the name that you have assigned.

Filter Pump

For 2-speed pumps: When a 2-speed pump is configured, one of the AUX relays must also
be configured to control the low speed motor winding on the pump (see page 13 for wiring
and page 24 for AUX configuration). See the Operation manual for specific information
regarding the control logic for 2-speed pump operation.

Freeze Protection

Freeze protection is used to protect the pool and plumbed equipment against freeze damage.
If freeze protection is enabled and the AIR temperature sensor falls below the freeze threshold
(see below), the Aqua Logic will turn on the filter pump to circulate the water. If “Pool and
Spa” is selected in the Pool/Spa sub-menu (see page 20), the valves will also alternate
between the pool and spa every 30 minutes and the filter pump will turn off while the valves
are turning. The heater(s) and chlorinator will not operate if freeze protection is the only

reason the pump is running.

Freeze Protection Temperature

Select the temperature to be used for freeze protection. T emperature is adjustable from 33ºF

- 42ºF (1ºC - 6ºC). 38ºF (3ºC) is default. This threshold will be used for all outputs that have
freeze protection enabled.

16

NOTE: Heater1 and Heater2 configuration are identical. If Heater2 is enabled then Valve4 will automatically be
disabled due to the fact that they use the same output relay and only 1 function can be assigned to that relay.

+

Heater1 Config.

+ to view/change

Heater1

Disable

if “Heater 1” is enabled

Heater1 Name

Gas Heater

if “Heater 1” is enabled

Heater1 Cooldown

Disabled

if “Heater 1” is enabled

Heater1 Extend

Disabled

Push to access heater options

>

>

Move to previous/next configuration menu
Toggle between Enabled and Disabled (default) Heater 1

+

>

>

Move to next menu item

+

Rotates between all available names

>

>

Move to next menu item
Toggle between Enabled and Disabled (default) Heater 1 Cooldown

+

>

>

Move to next menu item

Toggle between Enabled and Disabled (default) Heater 1 Extend

+

>

>

Move to next menu item

Heater1

If the heater is “Enabled”, the heater relay will turn on when the water temperature is less
than the desired temperature setting and the filter pump is running. The desired temperature
is in the “Settings Menu”. If applicable, the homeowner will be prompted to enter separate
“pool” and “spa” settings. Depending on the position of the pool/spa suction valve, the
proper temperature setting will be used.

Heater Name

The Aqua Logic allows you to assign any one of a number of names (e.g. “Gas Heater,
Heatpump, etc.) to each of the heater control functions. This will make the Aqua Logic much
more user friendly to the homeowner when they want to turn various heaters on or off or set
temperatures. A sheet of small name labels is included with the Aqua Logic main unit and
each remote display/keypad so that appropriate pushbuttons can be labeled the same as the
name that you have assigned.

Heater Cooldown

This feature ensures that the heater cools down before water circulation is stopped. When
enabled, The Aqua Logic will continue to run the filter pump for 15 minutes after the heater
turns off. During this period the filter pump LED will flash and also a “Heater Cooldown,
Filter Pump On” message will scroll on the display .

When the filter pump is running and the heater is on: Pressing the “Filter” button once will
cause the heater to turn off, but the filter pump will continue to run for heater cooldown (filter
LED flashing and message on display). Pushing the filter button a second time will override
the heater cooldown operation and turn the filter pump off.

For a Pool/Spa Setup selection of “Pool Only”, “Spa Only” or “Pool and Spa-Std”, Heater1
and/or Heater2 cooldown affect the filter pump. For “Pool and Spa-Dual”, Heater1 is associated
with the spa filter and Heater2 with the pool filter.

Heater Extend

If “Enabled”, the filter extend logic keeps the filter pump running beyond the normal turn-off
time until the pool (or spa) is heated up to the desired temperature setting (see Settings
Menu). Heater extend will NOT cause the filter pump to turn on, it will only delay the turn
off time when the heater is operating.

For a Pool/Spa Setup selection of “Pool Only”, “Spa Only” or “Pool and Spa-Std”, Heater1
and/or Heater2 will keep the filter pump running. For “Pool and Spa-Dual”, Heater1 will keep
the spa filter running and Heater2 will keep the pool filter running.

17

Solar Config.

+ to view/change

Solar

Disabled

if “Solar” is enabled

Solar Extend

Disabled

if “Solar” is enabled

Solar Priority

Disabled

Push to access solar options

+

>

Move to previous/next configuration menu

>

Toggle between Enabled and Disabled (default) Solar

+

>

>

Move to next menu item

Toggle between Enabled and Disabled (default) Solar Extend

+

>

>

Move to next menu item

+

Toggle between Enabled and Disabled (default) Solar Extend

>

>

Move to next menu item

Solar

The Solar configuration menu will NOT appear if “Pool and Spa - Dual” has been selected in
the Pool/Spa setup menu. If the solar control logic is “Enabled”, several additional steps
must be taken to ensure proper operation of the solar system. If the solar is operated by a
valve, then the Valve3 output must be setup for solar logic (page 25). If the solar is operated
by a pump, then one of the AUX relays must be set up for solar logic (page 24). Also, the
“solar” temperature sensor must be installed. This sensor is typically mounted near the
collector array and is used to sense whether sufficient solar heat is available.

If solar is “Enabled”, the valve or solar pump relay will turn on when the water temperature is
less than the desired temperature setting AND the solar sensor is hotter than the water . The
desired temperature is in the “Settings Menu”. If applicable, the homeowner will be prompted
to enter separate pool and spa desired temperature settings. Depending on the position of
the pool/spa suction valve, the proper temperature setting will be used.

Lights Config.

+ to view/change

Lights Name

Pool Light

Lights Function

Manual On/Off

Solar Extend

If “Enabled”, the filter extend logic keeps the filter pump running beyond the normal turn-off
time if solar heat is still available. When solar heat is no longer available, both the solar
valve/pump and filter pump will turn off simultaneously. Solar extend will NOT cause the
filter pump to turn on, it will only delay the turn off time when solar is operating.

Solar Priority

If both “Solar Control” and “Heater Control” are enabled, the Solar Priority feature will keep
the conventional heater off whenever solar heat is available. This provides the most cost
effective way of heating the pool. When solar heat is not available, the conventional heater
will operate normally .

Push to access Lights options

+

>

Move to previous/next configuration menu item

>

Rotates between all available names

+

>

>

Move to next menu item
Rotates between Manual On/Off (default), Countdown Timer, and Timeclock

+

>

>

Move to next menu item

Lights Name

The Aqua Logic allows you to assign any one of a number of names (e.g. “Pool Light, Spa
Light, Deck Light, etc.) to this control function. Note that other lights may be assigned to
some of the Aux outputs. This will make the Aqua Logic much more user friendly to the
homeowner when they want to turn various lights on or off. A sheet of small name labels is
included with the Aqua Logic main unit and each remote display/keypad so that the “Lights”

18

pushbutton can be labeled the same as the name that you have assigned. At this time it is
also a good idea to make sure that the relay in the control box is also labeled (hand written)
with the same name as a help to technicians who may service this system at a later date.

Lights Function

Manual On/Off—the lights relay will alternate between turning on and off when the LIGHTS
button is pressed. There is no automatic control logic.

Countdown Timer—the lights relay will turn on when the LIGHTS button is pressed. The
lights relay will turn off automatically after a programmed time (see Timers Menu in the
Operations Manual). The LIGHTS button can also be used to turn the output off.

Timeclock – the lights will turn-on and turn-off at the times set for the lights timeclock in the
Settings Menu (see Operations Manual). The LIGHTS button can also be used to turn the
output on and off.

NOTE: The configuration parameters for all Aux outputs are same as shown below for Aux1. PS-4: Aux1 and Aux2.
PS-8: Aux1 thr ough Aux6. PS-16: Aux1 through Aux14. Also note that for the PS-16, Valves7, 8, 9 and 10 are turned

On/Off with the control function selected for Aux7, 8, 9, and 10, respectively.

Aux1 Config.

+ to view/change

Aux1 Name

Cleaner Pump

Aux1 Function
Manual On/Off

for all functions except solar and
low speed of 2-speed filter pump

Aux1 Interlock

Disable

Aux1 Freeze

Disabled

WARNING: Do not use the Aqua Logic to control an automatic pool cover . Swim-

!

Push to access Aux1 options

+

>

>

Move to previous/next configuration menu item
Rotates between all available names

+

>

>

Move to next menu item
Rotates between

+

Solar, and Low speed of a 2-speed pump

>

>

Move to next menu item

Toggle between Enabled and Disabled (default) Aux1 Interlock

+

>

>

Move to next menu item
Toggle between Enabled and Disabled Aux1 Freeze (default)

+

>

>

Move to next menu item

Manual On/Off (default), Countdown Timer, T imeclock,

options

mers may become entrapped underneath the cover.

NOTE: If “Pool and Spa-Dual” is selected, Aux1 is dedicated to use as the spa filter. Its Name is set to Spa Filter, the
Function is set to Timeclock and Interlock is set to Disabled. These can’t be changed.

Aux1 Name

The Aqua Logic allows you to assign any one of a number of names (e.g. “Cleaner Pump,
W aterfall, Gazebo Light, etc.) to each of the aux outputs control function. This will make the
Aqua Logic much more user friendly to the homeowner when they want to turn various aux
equipment on or off or program the timeclocks. A sheet of small name labels is included with
the Aqua Logic main unit and each remote display/keypad so that the “Aux” pushbutton can
be labeled the same as the name that you have assigned. At this time it is also a good idea to
make sure that the relay in the control box is also labeled (hand written) with the same name
as a help to technicians who may service this system at a later date.

19

Aux1 Function

Manual On/Off (default)—the aux relay will alternate between turning on and off when the
aux button is pressed. There is no automatic control logic.

Countdown Timer – the aux relay will turn on when the AUX button is pressed and then will
turn off automatically after a programmed time (see Timers Menu in the Operations Manual).
The AUX button can also be used to turn the output off.

Timeclock – the aux relay will turn-on and turn-off at the times set for the aux1 (aux2)
timeclock in the Timers Menu (see Operations Manual). The AUX button can also be used
to turn the output on and off.

Solar – the aux relay operates a solar booster pump which will turn on when the filter pump
in running and solar heat is available and the water is less than the desired temperature
setting. It is important to note that “Solar Control” must be enabled in the “Solar Config.”
menu for proper operation to occur.

Low Speed of a 2-speed Filter Pump – the Aqua Logic will operate the aux relay whenever
the low speed operation of the filter pump is required. It is very important that the “2-speed”
filter pump option be selected under the “Filter Config.” Menu for proper operation.

Aux1 Interlock

If “Enabled”, this feature will override the function (manual on/off, countdown timer, timeclock,
selected above and turn the aux1 or aux2 relay off. This forced off condition occurs when:
filter pump is off, first 3 minutes of filter pump operation (allows the pump to prime and get
water flowing), when the pool/spa suction return valves are in any position other than “pool
only”, for 3 minutes after solar turns on (allows air in the solar panels to be purged). Interlock
is not available for solar or low speed filter pump functions.

Aux1 Freeze Protection

This function protects the pool, plumbing, and equipment against freeze damage. If Freeze
Protection is enabled and the AIR temperature sensor falls below 38°F, the Aqua Logic will
turn on the aux relay to circulate the water. IMPOR T ANT : this only enables operation of the
AUX output during freeze--see the “Filter Pump Config.” menu to enable freeze protection
for the main circulation system.

20

NOTE: The configuration for Valve3 and Valve4 are identical. However, if Heater2 was enabled, then the Valve4
configuration will not appear (a single relay is used to implement either the Heater2 function or the Valve4 function-

-it can not do both). For PS-16, see aux logic on previous page for control of Valves7, 8, 9 and 10.

Valve3 Config.

+ to view/change

Valve3 N ame

Wat erfall

Valve3 Function

Solar

for all functions except solar

Valve3 I nt erlock

Disabled

Valve3 F re eze

Disabled

Push to access Valve3 options

+

>

Move to previous/next configuration menu item

>

+

Rotates between all available names

>

>

Move to next menu item
Rotates between Timeclock, Manual On/Off, Solar , Countdown

+

and In-Floor Cleaner

>

>

Move to next menu item
Toggle between Enabled and Disabled (default) Valve3 Interlock

+

>

Move to next menu item

>

Toggle between Enabled and Disabled (default) Valve3 Freeze

+

>

>

Move to next menu item

(default)

Valve3 Name

The Aqua Logic allows you to assign any one of a number of names (e.g. “Cleaner Valve,
W aterfall valve, Solar Valve, etc.) to each of the valve output control function. This will make
the Aqua Logic much more user friendly to the homeowner when they want to turn various
valves on or off or program the timeclocks. A sheet of small name labels is included with the
Aqua Logic main unit and each remote display/keypad so that the “Valve3” (and “Valve4”)
pushbutton can be labeled the same as the name that you have assigned.

Valve3 Function

Timeclock – the valve turns on/off at the times set for the Valve3 timeclock in the Timers
Menu (see Operations Manual). The Valve 3 button can also be used to turn the valve
output on or off.

Manual On/Off —the valve3 relay will alternate between turning on and off when the VAL VE3
button is pressed. There is no automatic control logic. The VAL VE3 button can also be used
to turn the valve output on or off.

Solar (default) – the valve operates when the filter pump is running and solar heat is
available and the water is less than the desired temperature setting. Solar heating must be
enabled in the “Solar Config. menu for proper operation to occur.

Countdown Timer – the valve3 relay will turn on when the VALVE3 button is pressed and
then will turn off automatically after a programmed time (see Timers Menu in the Operations
Manual). The VALVE3 button can also be used to turn the output off.

In-Floor Cleaner – the valve switches the water returning to the pool between the in-floor
cleaner and the normal return jets which facilitate efficient surface skimming. The valve will
operate the in-floor cleaner for the first half of each clock hour and then switch to the jets/
skimming for the last half of the hour.

Valve3 Interlock

If “Enabled”, this feature will override the function (timeclock, or in-floor cleaner) selected
above and turn the valve off whenever the filter pump is off or the pool/spa suction/return
valves are set to “spa only” or “spillover” operation. Interlock is not available with solar.

21

Valve3 Freeze Protection

This function protects the pool and plumbed equipment against freeze damage. If Freeze
Protection is enabled and the AIR temperature falls sensor falls below 38°F, the Aqua Logic
will turn on the valve to allow circulation of the water. IMPORTANT: this only enables
operation of the Valve3 output during freeze--see the “Filter Pump Config.” menu to enable
freeze protection for the main circulation system.

All Timeclocks

7-day

Time Format

12 hour AM/PM

Units

ºF and PPM

Reset Config. to

Default Press +

Are you sure?

+ to proceed

Config. reset

Confirmed

Toggle between 7-day (default) and Weekend/Weekday time options

+

>

Move to previous/next configuration menu item

>

This selection affects ALL of the timeclock logic in the Aqua Logic. If “7-day” is selected,
each timeclock will have one set of turn-on/turn-off settings that operate every day of the
week. If “W eekend/W eekdays” option is selected then the user can enter one set of turn-on/
turn-off times for the weekend (fixed as Saturday/Sunday) and another set of turn-on/turn­off times for weekdays (Monday through Friday).

Toggle between 12 hour AM/PM (default) and 24 hour time format options

+

>

>

Move to previous/next configuration menu item

Toggle between ºF and PPM (default) and ºC and g/L (Metric) options

+

>

>

Move to previous/next configuration menu item

Initiate reset of all configuration parameters

+

>

Move to previous/next configuration menu item (config not reset)

>

>

Reset all configuration parameters

+

>

Move to previous/next configuration menu item (config not reset)

>

>

>

Move to previous/next configuration menu item (config reset)

>

>

Use this function to erase all previous system configuration settings and reset all configuration
parameters back to the factory default values. This function is NOT reversible--be careful.

22

Quick “How To” Guide

Operate the Spa—Manually

1. Press the “Pool/Spa” button to go to “spa-only” operation (“SP A” LED illuminated). In some
cases, this may take more than one press of the button.

2. If the filter pump is not already on, press the “FIL TER” button to turn it on.

3. If the spa is below the desired temperature, the heater will turn on automatically when the filter
pump is on and the valves are in the spa-only position. If you have not already set the desired
temperature for the spa, see “Set Heater T emperature” below

4. If the spa has a separate jet pump and or blower , determine if the jet pump/blower is con­trolled by Aux1 or Aux2 (it should be marked on the label inside the door). Then press the
appropriate button to turn on the jets/blower .

Operate the Spa—Automatically

1. Press the “MENU” button repeatedly until “T imers Menu” is displayed

2. Press the “>” button repeatedly until the “Spa—all days” or “Spa—weekends” is displayed.

3. Use the “+” and “-“ buttons to set the desired start time, then press “>” to switch to the off
time. Use the “+” and “-“ buttons to adjust the off time. If you are setting the “weekend”
timeclock, press “>” to go to the “weekday” settings.

Note: During the programmed spa time, the valves will automatically switch to the
“spa-only” position, the filter pump will turn on, and, if the spa is not up to the desired
temperature, the heater will start. This operation is the highest priority and will take
precedence over other automatically programmed operations. At the end of the spa
period, the Aqua Logic will return to its normally programmed operation state.

Set the Heater Temperature (or turn heater permanently off)

1. Press the “MENU” button repeatedly until “Settings Menu” is displayed

2. Press the “>” button repeatedly until the “Spa Heater” or “Pool Heater” is displayed.

3. Press the “+” or “-“ buttons repeatedly to adjust the temperature. If you adjust the tempera­ture below 65ºF or above 104°F the display will indicate “off” and the heater will not operate
regardless of temperature.

Note: Separate temperatures for the pool and spa must be set. If the valves are in the
pool-only or spa spillover positions, then the heater will use the pool setting. If the
valves are in the spa-only position then the heater will operate according to the spa
setting.

Set the Chlorinator Output

1. Press the “MENU” button repeatedly until “Settings Menu” is displayed

23

2. Press the “>” button repeatedly until the “Spa Chlorinator” or “Pool Chlorinator” is displayed.

3. Press the “+” or “-“ buttons repeatedly to adjust the setting. If you adjust the setting to 0% the

chlorinator will be off all the time

Note: Separate chlorinator output levels for the pool and spa must be set. If the valves
are in the pool-only or spa spillover positions, then the chlorinator will operate per the
pool setting. If the valves are in the spa-only position then the chlorinator will operate
according to the spa setting. The actual amount of chlorine intr oduced into the pool/spa
is determined by: this output setting, the amount of time the filter pump is running, the
water temperature, and the amount of salt in the water. Also see Start/Stop
Supechlorination below .

St art/Stop Superchlorination

1. Press the “MENU” button repeatedly until “Settings Menu” is displayed

2. Press the “>” button repeatedly until “Super Chlorinate” is displayed.

3. The display will show whether superchlorination is “on” or “off”.

4. Press “+” or “-“ to toggle between “on” and “off”

Note: Once started, superchlorination will run for the programmed number of hours
(Timers Menu/Super Chlorinate Hours) or until you manually turn it off.
Superchlorination may be temporarily interrupted for a pr ogrammed spa operation.

Program a Timeclock

1. Press the “MENU” button repeatedly until “Timers Menu” is displayed

2. Press the “>” button repeatedly until the “xxx—all days” or “xxx—weekends” is displayed.

3. Use the “+” and “-“ buttons to set the desired start time, then press “>” to switch to the off
time. Use the “+” and “-“ buttons to adjust the off time. If you are setting the “weekend”
timeclock, press “>” to go to the “weekday” settings.

Note: During the programmed time, there may be other automatic or manual opera­tions that prevent the r elay/valve fr om operating—see a mor e detailed discussion under
Automatic System Operation/Timers Menu/Aux Timeclock or in Troubleshooting/Diag­nostic Information.

Program a Countdown Timer

1. Press the “MENU” button repeatedly until “Timers Menu” is displayed

2. Press the “>” button repeatedly until the “xxx—Timer” is displayed.

3. Use the “+” and “-“ buttons to set the desired timer period.

Note: A setting of 0:00 will display as “manual on/off.” The countdown automatic
turn off function is disabled by manual operation is still permitted. There may be other
automatic or manual operations that prevent the relay/valve from operating—see a
more detailed discussion under Automatic System Operation/Timers Menu/Aux T imeclock
or in T roubleshooting/Diagnostic Information.

24

Enter/Exit Service (or Service—Timed) Mode

1. Go to Aqua Logic main unit (normally mounted near the pool equipment)

2. Pressing the “Service” button rotates through normal operation (red LED off), service mode
(red LED on continuously) and service-timed mode (red LED flashing).

Note: This operation can only be performed at the main Aqua Logic unit. Both “Ser­vice” and “Service-Timed” disable all automatic programmed operations and allow
manual operation from the main unit only. The buttons on the remote display/keypads
will still be able to turn equipment off in case of an emergency, but will not turn any
equipment on. If the system is in “Serviced-Timed” it will automatically switch back to
normal operation at the end of the time period.

25

Chlorinator Operation / Water Chemistry

1

The table below summarizes the levels that are recommended by the National Spa and Pool Institute
(NSPI). The only special requirements for the Aqua Logic are the salt level and stabilizer. It is important
to maintain these levels in order to prevent corrosion or scaling and to ensure maximum enjoyment of the
pool. T est your water periodically . Y our Authorized Aqua Dealer or most pool stores can provide you
with the chemicals and procedures to adjust the water chemistry . Be sure to tell the pool store that you are
using an Aqua Logic chlorine generator.

Saturation Index

The saturation index (Si) relates to the calcium and alkalinity in the water and is an indicator of the pool
water “balance”. Your water is properly balanced if the Si is 0 ±.2. If the Si is below -0.2, the water is
corrosive and plaster pool walls will be dissolved into the water . If the Si is above +0.2, scaling and
staining will occur. Use the chart below to determine the saturation index.

Si = pH + Ti + Ci + Ai - 12.

ºC ºF Ti
12

53

16

60

19

66

24

76

29

84

34

94

39

103

How to use: Measur e pool pH, t emper atur e, cal cium hardne ss,
and total alkalinity. Use the chart above to determine Ti, Ci,and
Ai from your meas ureme nts. Inser t valu es of pH, Ti, Ci an d Ai
into the abov e equation. If Si equals . 2 or more, s caling and
staining may occur. If Si equals -.2 or less corrosion or irritation
may occur.

CORROSIVE SCALING

Calcuim

Hardness

.3

75 75

100 100

.4

125 125
150 150

.5

200 200

.6

250 250
300 300

.7

400 400

.8

600 600
800 800

.9

-.2

1.5 1.9

1.6 2.0

1.7 2.1

1.8 2.2

1.9 2.3

2.0 2.4

2.1 2.5

2.2 2.6

2.4 2.8

2.5 2.9

0.2

Ci

Total

Alkalinity

Ai

OK

26

Salt Level (When using optional chlorinator function - requires AQL-CL chlorination kit)

Use the chart on page 28 to determine how much salt in pounds or (Kgs) need to be added to reach the
recommended levels. Use the equations below (measurements are in feet/gallons and meters/liters) if pool
size is unknown.

Liters

Rectangular

Round

Oval

Gallons

(pool size in fee t)

Length x Width x
Average Depth x 7.5

Diameter x Diameter x
Average Depth x 5.9

Length x Width x
Average Depth x 6.7

(pool size in meters)

Length x Width x
Average Depth x 1000

Diameter x Diameter x
Average Depth x 785

Length x Width x
Average Depth x 893

The ideal salt level is between 2700-3400 PPM (parts per million) with 3200 PPM being optimal. If the
level is low , determine the number of gallons in the pool and add salt according to the chart on page 28. A
low salt level will reduce the efficiency of the Aqua Logic and result in low chlorine production. The salt
in your pool/spa is constantly recycled and the loss of salt throughout the swimming season should be
small. This loss is due primarily to the addition of water because of splashing, backwashing, or draining
(because of rain). Salt is not lost due to evaporation.

Type of Salt to Use

It is important to use only sodium chloride (NaCl) salt that is greater than 99% pure. This is common food
quality or water softener salt and is usually available at building supply stores in 40-80 lb. bags labeled
“Coarse Solar Salt”. It is also acceptable to use water conditioning salt pellets, however, it will take longer
for them to dissolve. Do not use rock salt, salt with yellow prussiate of soda, salt with anti-caking addi­tives, or iodized salt.

How to Add or Remove Salt

For new plaster pools, wait 10-14 days before adding salt to allow the plaster to cure. Turn the circulating
pump on and add salt directly into the pool. Brush the salt around to speed up the dissolving process—do
not allow salt to pile up on the bottom of the pool. Run the filter pump for 24 hours with the suction coming
from the main drain (use pool vacuum if there is no main drain) to allow the salt to evenly disperse through­out the pool. The salt display may take 24 hours to respond to the change in salt concentration.

The only way to lower the salt concentration is to partially drain the pool and refill with fresh water.
Always check stabilizer (cyanuric acid) when checking salt. These levels will most likely decline together .

Use the chart on page 29 to determine how much stabilizer must be added to raise the level to 80 PPM.

27

(398)

267

190

67

63

127

800 10 67

747

693 960

640 907

587 854

480

(364) (484)

(339) (460)

(315) (436)

(291) (412)

(267) (388)

(218) (242)

750 1000

700 950

650 900

600 850

550 800

500

450

(363)

(341) (453)

(318) (430)

(295) (408)

(273) (385)

(250)

(227)

(205)

57

50

(45) (60)

(23) (30)

100 133

47

93

(21) (29)

(42) (57)

87 120

(39) (54)

43 60

(20) (27)

80 113

(36) (51)

(18) (26)

40

73 107

(33) (48)

37 53

(17) (24)

67

33

(30)

(15)

60

(27)

30

(14)

350 467

327 443

303 420

280 397

257 373

233

210

(159) (211)

(148) (201)

(138) (190)

(127) (180)

(1 17) (169)

(106)

(95)

340

300 400

280 380

260 360

240

220 320

200

180

(136) (181)

(127) (172)

(118) (163)

(109) (154)

(100) (145)

(91)

(82)

(310)

(195)

650 867

700 933

653 88 7

607 840

560 793

513 747

467

420

(318) (424)

(297) (403)

(276) (382)

(255) (360)

(233) (339)

(212)

(191)

(297)

607 823

(276) (378)

563 780

(256) (358)

520 737

(236) (337)

477 693

(217) (317)

433

(197)

390

(177)

600 800

560 7 60

520 720

480 680

440 640

400

360

(273) (364)

(255) (346)

(236) (328)

(218)

(200) (291)

(182)

(164)

550 733

513 697

477 660

440 623

403 587

367

330

(250) (333)

(233) (317)

(217) (300)

(200) (283)

(183) (267)

(167)

(150)

500 667

467 633

433 600

400 56 7

367 533

333

300

(227) (304)

(212) (289)

(197) (274)

(182) (258)

(167) (243)

(152)

(136)

450 600

420 570

390 540

360 510

330 480

300

270

(205) (263)

(191) (259)

(177) (246)

(164) (232)

(150) (218)

(136)

(123)

400 533

373 507

347 480

320 453

293 427

267

240

(182) (243)

(170) (231)

(158) (219)

(145) (207)

(133)

(121)

(109)

227

(68) (90)

(91) (123)

150 200

200

250 333

(114) (152)

(64) (86)

187 253

(85) (117)

233 317

(106) (144)

(98) ( 137)

217 300

(91) (129)

200 283

(83) (121)

183 2 67

(76)

167

(68)

150

173 240

160

147 213

133

120

(79) (110)

(73) (104)

(67) (98)

(61)

(55)

140

(59) (81)

130 180

(55) (77)

120 170

(50) (73)

110 160

(45)

100

90

(41)

Gallons and (Liters) of Pool/Spa water

POUNDS and (Kg) OF SALT NEEDED FOR 3200 PPM

Current salt

427

400

(182)

(194)

373

350

(170)

(159)

320

300

(145)

12,000 14,000 16,000 18,000 20,000 22,000 32,00024,000 34,00026,000 36,00028,000 38,00030,000 40,000

(45000) (52,500) (60,000) (67,500) (75,000) (82,500) (120,000)(90,000) (127,500)(97,500) (135,000)(105,000) (142,500)(112,500) (150,000)ppm

267

10,000

(37,500)

(136)

(121)

373

327

280

(170)

(148)

(127)

(106)

347

303

260

217

(158)

(138)

(118)

(98)

293

267

320

(145)

(133)

(117)

257

280

(127)

220

240

(109)

(100)

(91)

240

(121)

(106)

233

210

(91)

200

180

(97)

187

213

(109)

(95)

(85)

163

187

(82)

(73)

160

140

(73)

(85)

160

(74)

140

120

(64)

(64)

(55)

(61)

133

(53)

117

(45)

100

80

(36)

(48)

107

93

(42)

(32)

80

60

(36)

(27)

67

27

53

(12)

(24)

47

(21)

23

(9)

40

20

(18)

(15)

OK OK OK OK OKOK OKOK OKOK OKOK OK

(11)

OK

OK

Ideal Ideal Ideal Ideal Ideal Ideal IdealIdeal IdealIdeal IdealIdeal IdealIdeal Ideal

Ideal

OK

Dilute D ilute Dilute D ilute Dilute D ilute DiluteDilute DiluteDilute DiluteDilute DiluteDilute Dilute

Dilute

80 100

2000

67 83

(36) (45)

(30) (38)

2200

(97)

213

8,000

(30,000)

level

(91) (1 14)

200 250

0

200

173

(79)

(85)

187 233

400

600

160 200

(73)

800

147 183

1000

(61) (76)

1200

(55) (68)

120 150

1400

(67) (83)

133 167

93 117

(48) (61)

1600

(42) (53)

1800

107 133

53

(24) (30)

2400

40 50

(18) (23)

2600

(6) (8)

13 17

27 33

(12)

3000

2800

OK

Ideal

3200

3400

Dilute

3600+

28

6.7

(7.5)

26.7

40,000

(150000)

25.3

38,000

(142500)

20.0

(10.5)

(12.0)

(8.6)

22.2

19.0

(10.0)

(11.5)

(9.0)

23.3

(6.0)

16.7

15.8

10.0

13.3

9.5

(7.1)

(5.7)

12.7

3.3

(4.5)

(3.0)

(1.5)

6.3

3.2

(4.3)

(2.8)

(1.4)

(9.5)

(8.1)

36,000

34,000

32,000

30,000

28,000

26,000

24,000

22,000

20,000

Gallons and (Liters) of Pool/Spa water

18,000

21.0

(135000)

19.8

22.7

(10.3)

(127500)

(9.7)

18.7

21.3

(120000)

(9.1)

17.2

20.0

(112500)

(8.5)

16.4

18.7

(105000)

15.2

(97500)

(7.3)

14.0

16.0

(90000)

(6.7)

12.9

14.7

(82500)

(6.1)

11.7

13.4

(75000)

(5.4)

10.5

12.0

(67500)

15.0

18.0

(9.0)

14.2

(8.5)

(7.2)

16.0

13.3

(8.0)

(6.8)

12.5

15.0

(7.4)

(6.4)

11.7

14.0

(6.9)

(5.9)

10.8

13.0

(6.4)

(5.4)

10.0

12.0

(5.9)

9.2

(5.0)

11.0

(5.3)

8.4

(4.5)

10.0

7.5

9.0

(4.8)

(2.2)

9.0

(6.7)

(5.4)

12.0

8.5

(6.3)

8.0

(4.8)

(6.0)

10.7

7.5

(5.6)

(4.5)

10.0

7.0

9.3

(5.2)

(4.2)

6.5

8.7

(4.9)

(3.9)

8.0

6.0

(3.6)

(4.5)

5.5

7.4

(3.3)

(4.2)

5.0

6.7

(3.8)

(3.0)

6.0

4.5

(2.7)

(3.4)

3.0

(4.1)

(3.9)

(3.6)

(3.4)

(3.2)

(2.9)

(2.7)

(2.5)

(2.3)

(2.0)

(1.3)

5.7

2.8

(1.3)

(2.6)

5.3

5.0

4.7

4.3

4.0

3.7

3.3

3.0

0.00.0 0.00.0 0.00.0 0.00.0 0.0

2.7

(2.4)

(1.2)

2.5

(2.3)

(1.2)

2.3

(2.1)

(1.1)

2.2

(2.0)

(1.0)

2.0

(1.8)

(.91)

1.8

(1.7)

(.82)

1.7

(1.5)

(.77)

1.5

(.68)

(1.4)

9.4

(4.9)

10.7

16,000

(60000)

6.7

8.0

(4.3)

5.4

(3.0)

(3.6)

2.7

4.0

(2.4)

1.4

(1.2)

(1.8)

(.64)

POUNDS and (Kg) OF STABILIZER (CYANURIC ACID) NEEDED FOR 80 PPM

8.2

9.4

(4.3)

14,000

(52500)

5.9

7.0

(3.7)

(3.2)

3.5

4.7

(2.7)

2.3

1.2

(1.6)

(2.1)

(1.1)

(.54)

)

7.0

8.0

(3.6)

12,000

(45000)

5.8

6.7

(4.3)

10,000

(37500)

4.7

5.3

(3.6)

8,000

(30000)

Current

0 ppm

Stabilizer

Level (ppm)

5.0

6.0

(3.2

(2.7)

4.2

(3.7)

3.3

4.0

(3.2)

(2.7)

20 ppm

10 ppm

30 ppm

3.0

4.0

(2.3)

3.3

(2.7)

2.7

(2.3)

2.0

1.0

(1.4)

(1.8)

(2.1)

(1.8)

40 ppm

(.91)

2.5

1.7

(1.6)

(1.1)

2.0

1.3

(.91)

(1.4)

60 ppm

50 ppm

0.00.0 0.00.0 0.0 0.0 0.0 0.0

(.45)

0.8

(.54)

0.7

(.45)

70 ppm

80 ppm

29

System Maintenance

T o maintain maximum performance, it is recommended that you open and visually inspect the cell every 3
months or after cleaning your filter . The Aqua Logic will remind you to do this by displaying the message
“Inspect/Clean Cell” after approximately 500 hours of operation.

The Aqua Logic electrolytic cell has a self cleaning feature incorporated into the electronic control’s logic.
In most cases this self cleaning action will keep the cell working at optimum efficiency . In areas where
water is hard (high mineral content) or in pools where the water chemistry has been allowed to get “out of
balance”, the cell may require periodic cleaning.

Servicing and Cleaning the Aqua Logic Cell

Turn off power to the Aqua Logic before removing the electrolytic cell. Once removed, look inside the cell
and inspect for scale formation (light colored crusty or flaky deposits) on the plates and for any debris
which has passed through the filter and caught on the plates. If no deposits are visible, reinstall. If deposits
are seen, use a high pressure garden hose and try to flush the scale off. If this is not successful, use a plastic
or wood tool (do not use metal as this will scratch the coating off the plates) and scrape deposits off of
plates. Note that a buildup on the cell indicates that there is an unusually high calcium level in the pool (old
pool water is usually the cause). If this is not corrected, you may to have to periodically clean the cell. The
simplest way to avoid this is to bring the pool chemistry to the recommended levels as specified.

Mild Acid Washing: Use only in severe cases where flushing and scraping will not remove the majority
of deposits. T o acid wash, turn off power to Aqua Logic. Remove cell from piping. In a clean plastic
container, mix a 2:1 solution of water to muriatic acid (one gallon of water to two quarts of muriatic acid).
AL W A YS ADD ACID TO WA TER - NEVER ADD WA TER T O ACID. Be sure to wear rubber gloves
and appropriate eye protection. The level of the solution in the container should just reach the top of the
cell so that the wire harness compartment is NOT submerged. It may be helpful to coil the wiring before
immersing the cell. The cell should soak for a few minutes and then rinse with a high pressure garden hose.
If any deposits are still visible, repeat soaking and rinsing. Replace cell and inspect again periodically .

Winterizing

The Aqua Logic electrolytic cell and flow detection switch will be damaged by freezing water just as your
pool plumbing would. In areas of the country which experience severe or extended periods of freezing
temperatures, be sure to drain all water from the pump, filter, and supply and return lines before any
freezing conditions occur . The electronic control is capable of withstanding any winter weather and should
not be removed.

If you are in an area that only experiences occasional freezing conditions, your Aqua Logic system may be
set up to circulate the pool water whenever the air sensor drops to 38ºF . Make sure the air sensor is
recording the correct temperature and is NOT located in the direct sunlight to ensure proper freeze pro­tection operation.

Spring Start-up

When first starting the pool in the spring time, it is highly recommended that you temporarily set the pool
and spa chlorinator settings (Settings Menu/Pool Sanitizer & Spa Sanitizer) to 0% (off) and then manually
shock the pool with any chlorine based shock product and balance the pool water chemistry per the levels
indicated in the Chlorinator Operation section (page 26). Make sure to check the salt and stabilizer levels
and bring them up to the recommended levels. Your local Authorized Aqua Dealer or pool store can
recommend the best chemical treatment for your pool. After the water is clear and balanced, then go back
and adjust the pool and spa chlorinator settings to the appropriate levels. T est the pool chlorine level
weekly and adjust the chlorinator settings up or down accordingly .

It is usually a good idea to also inspect the cell and clean if necessary at the start of the season. See
instructions above.

30

Troubleshooting and Diagnostic Information

The Aqua Logic provides 2 different tools to aid in troubleshooting any problems that may occur in your
pool and/or spa system. The Service mode will allow you to disable automatic operation and manually
control most of the equipment (the heater and general purpose Valve3 output are the exceptions). The
Diagnostic Menu will provide some detailed information regarding system operation.

While both of the features are primarily intended for the use of the professional service technician, their
function is fully explained below . If you believe your system is not operating properly or have questions
regarding the operation, call the Goldline T echnical Service Dept. from Monday through Friday , 8AM to
8PM EST at 888-9221-7665.

Service Mode

The main unit keypad has a SER VICE button that is used primarily during servicing of the pool equipment.
If you want to completely disable the automatic operation and operate the system manually , you can put

the system into Service or Service-Timed mode by pressing the “Service” button. Pressing the “SER­VICE” button once will switch the system into service mode which means that all automatic functions are
disabled, the optional remote display/keypads are disabled (except for manual turn off for emergencies).
The outputs can be manually controlled by pressing the buttons on the local display/keypad. The red
“SER VICE” LED will be illuminated and the Aqua Logic will remain in this mode of operation until manu­ally taken out of service mode.

Pressing the “SER VICE” button again will cause the Aqua Logic to switch to service-timed mode which is
very similar to service mode, except that the Aqua Logic will automatically return to normal operation after
3 hours. During service timed operation, the “SER VICE” LED will flash and the time remaining will be
displayed on the remote display/keypad(s).

Pressing the “SER VICE” button again, will return the Aqua Logic to normal (automatic) operation.

31

Check System Indicator

The “CHECK SYSTEM” LED will alert you when the Aqua Logic detects any of the following conditions
that are abnormal and require attention for optimal operation of your pool.

• Inspect Cell -- for optimum operation, you will need to inspect the Aqua Logic chlorinator cell ap-

proximately every 3 months and clean the cell if necessary . The Aqua Logic will automatically remind
you when it is time and display “Inspect Cell, + to reset” as part of the rotating Default Menu. Clean the
cell (see instructions, pg 28) and then press the “+” button during the “Inspect Cell” display to reset the
timer.

• Low Salt/Minerals or Very Low Salt/Minerals -- when the salt is too low the Aqua Logic will

generate less chlorine and the life of the cell is degraded. Check the cell and clean if necessary (see
instructions, pg 28) before adding salt (see instructions, pg 25).

• High Salt/Amps/Minerals -- the Aqua Logic will stop generating chlorine under certain high salt

conditions in order to protect the internal electronics from damage. The only way to lower the salt level
is to partially drain the pool and add fresh water .

• Water/Pool Sensor -- if the water or pool (if Dual Equipment) sensor is either an open or short circuit.

• Air sensor -- if the freeze protection feature is enabled (Configuration Menu/ Filter Config.) and the air

sensor is either an open or short circuit

• Solar/Spa sensor -- if the solar (if solar is enabled), (Configuration Menu/Solar Config.) or spa (if

Dual Equipment) sensor is either an open or short circuit.

• Chlorinator Cell sensor -- if the chlorinator function enabled (Configuration Menu/Chlorinator) and

the cell sensor is either an open or short circuit.

• PS-16 Communciation Error -- if an AQL-PS-16 and the Expansion Unit is not responding.

• Low V olts -- if the chlorinator cell voltage is too low .

• No Cell Power -- if a chlorinator cell power problem is detected on the printed circuited board.

• No Flow -- if the filter pump is on and the flow switch indicates no flow for 3 minutes or more.
For helpful troubleshooting information on any of these issues, go to the Diagnostic Menu and then scroll

through the various items until you see the cause for the “CHECK SYSTEM” LED being illuminated.

32

Diagnostic Menu

T o enter the Diagnostic Menu, press the “Menu” button repeatedly until the display shows “Diagnostic
Menu”. At this point, you can use either the “<” or “>” buttons to scroll through the various menu items
which are described below:

Press to switch chlorinator operation to opposite polarity (15 second delay)

Set Day and Time

+23.45 +6.75A
Wednesday 10:37P

84°F 3200PPM

+

>

>

Move to previous/next menu item

+/- 23.45V is the voltage applied to the chlorinator cell
+/-6.75A is the current (amps) through the cell
84ºF is the water temperature at the cell
3200PPM is the “instant” salt level at this time

For the chlorinator to be operating, several other things must be happening: the filter pump
must be running, the flow switch must be detecting flow, the chlorinator setting must be set
greater than 0%, the water temperature at the cell must be between 50ºF and 140ºF , and the
salt level must be within the operating range. If any of these conditions are not met, the
chlorinator diagnostic display will tell you the reason. It’s possible to have more than one
reason, in which case after you rectify what was displayed the first time, a second display will
appear.

If the current (amps) display is 0.00A, then the chlorinator is operating normally but is in the
off part of its normal operating cycle. Simply press either the “+” or “-“ key to start a new
cycle.

The Aqua Logic periodically reverses the polarity of the voltage applied to the cell in order
to automatically clean off any calcium deposits. It is important that you check the chlorinator
operation in both polarities. T o do this, press either the “+” or “-“ buttons and the chlorinator
will turn off, wait for 15 seconds and then turn on in the opposite polarity .

Instant Salt

3200 PPM (+=save)

Flow Switch

Flow

If a conventional or solar heater is operating, it is likely that the temperature of the water at
the cell is higher than the pool/spa water temperature displayed on the Aqua Logic default
display.

+

Press to load the “Instant Salt” into the averaged salt display

>

>

Move to previous/next menu item

This display shows “Instant Salt” or “Instant Minerals” (if Chlor. Config. is set for “Display
Minerals”). The “Instant Salt” is calculated based on the voltage, current (amps), and water
temperature at the cell. This is different than the “average salt” value which is displayed as
part of the default menu. There are a number of reasons why instant and average salt
readings may differ. Some of these include salt having just been added to the pool and not
yet thoroughly mixed, calcium buildup on the cell, and the cell aging.

No functi on

+

>

>

Move to previous/next menu item

The current status of the flow switch is displayed. There is a short delay when transitioning
from flow to no-flow and a longer delay on the transition from no-flow to flow. The delay time
is displayed.

33

Cell Temp Sensor

77ºF

+

No function

>

>

Move to previous/next menu item

Wat er Se nso r

Open circuit

Air Sensor

94ºF

Solar Sensor
Short circuit

Main Software

Revision 2.01

Display Software

remote-08 r3.10

for PS-16 only

Exp. Unit Software

Revision 1.00

RF Base Software

r1.00 ID:1234

+

No function

>

>

Move to previous/next menu item
No function

+

>

Move to previous/next menu item

>

No function

+

>

>

Move to previous/next menu item

NOTE: If Pool and Spa-Dual is selected, the solar sensor will display as “Spa Sensor” and the
water sensor will display as “Pool Sensor”.

If the sensor appears to operating properly, then the temperature will be displayed. If this
temperature is not correct then check the placement of the sensor. If the problem is not
placement related, then the sensor will, most likely, require replacement. If the display is
“Open Circuit” or “Short Circuit” then check the wiring to the sensor and also make sure that
the wires are secure in the terminal block in the Aqua Logic main unit.

+

No functi on

>

>

Move to previous/next menu item

+

No functi on

>

>

Move to previous/next menu item

+

No functi on

>

>

Move to previous/next menu item

+

No functi on

>

>

Move to previous/next menu item

If you call the Goldline T echnical Service Dept. for assistance, they may ask for the software
revisions of both the main unit and each of the display/keypads or other devices that are
attached to the system. Note that it is possible that different display/keypads have different
software revision levels. For this reason, it is advisable to check this diagnostic menu item
on every display.

34

The following statement is applicable if any of the wireless accessories are connected to the Aqua Logic
system.

FCC Statement

(Compliance Statement, Part 15.19): This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.

W ARNING (Part 15.21): Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.

Industry Canada Statement

The term “IC” before the certification/registration number only signifies that the Industry Canada technical
specifications were met.

Interference

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, then the user is encouraged to try to correct the interfer­ence by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment into a power source on different circuit than the receiver.

35

Limited Warranty—Pool Automation & Chlorination Pr oducts

10/1/2004

This warranty statement is applicable to all pool automation and chlorination products manufactured by Goldline Controls, Inc.
(Goldline) on or after October 1, 2004. See the appropriate warranty statement for other Goldline products or for pool automation
and chlorination products produced prior to October 1, 2004.

Aqua Rite/Trol/Logic—Residential pools in USA or Canada:

Goldline warrants Aqua Rite, Aqua Trol, and Aqua Logic products (products with Goldline part numbers starting with AQ-RITE-,
AQ-TROL-, AQ-LOGIC-, AQL-P-, AQL-PS-,or AQL-CL-) installed on private, residential swimming pools within the USA or
Canada to be free from defects in material or workmanship, under normal use and service for
installation, provided it is installed in accordance with the Goldline installation instructions and specifications provided with the
product. If written proof of the date of the initial system installation is not provided to Goldline, the manufacturing datecode on the
Aqua Rite, Aqua Trol, or Aqua Logic electronics unit will be the sole determinant of the date of the initial system installation.

If a product is defective, in workmanship or materials and is removed and returned freight prepaid within three (3) years after the date
of the initial system installation, Goldline Controls will, at its option, either repair or replace the defective product and return it freight
prepaid. If the defective product is returned freight prepaid to Goldline more than three (3) years but within five (5) years of the date
of the initial system installation, Goldline, at its option, will either repair or replace the defective product and will charge sixty percent
(60%) of the current list price for such repairs or replacements, plus shipping charges. The costs incurred in removal and/or
reinstallation of the product are NOT covered under this warranty.

Aqua Rite/Trol/Logic— Commercial pools or any pool outside of the USA or Canada:

Goldline warrants Aqua Rite, Aqua Trol, and Aqua Logic products (products with Goldline part numbers starting with AQ-RITE-,
AQ-TROL-, AQ-LOGIC-, AQL-P-, AQL-PS-,or AQL-CL-) installed on commercial pools anywhere or any non-private single
family residential pool or any pool outside of the USA or Canada to be free from defects in material or workmanship, under normal
use and service for
installation instructions and specifications provided with the product. If written proof of the date of the initial system installation
is not provided to Goldline, the manufacturing datecode on the Aqua Rite, Aqua T rol, or Aqua Logic electronics unit will be the sole
determinant of the date of the initial system installation.

one year from date of the initial system installation, provided it is installed in accordance with the Goldline

five years from date of the initial system

If a product is defective, in workmanship or materials and is removed and returned freight prepaid within one (1) year after the date
of the initial system installation, Goldline will, at its option, either repair or replace the defective product and return it freight prepaid.
The costs incurred in removal and/or reinstallation of the product are NOT covered under this warranty.

Accessory Products and Replacement parts—any pools, anywhere:

Goldline warrants any replacement parts or accessory products (any pool automation or chlorination product or part with a part
number other than AQ-RITE-, AQ-TROL-, AQ-LOGIC-, AQL-P-, AQL-PS-,or AQL-CL-) to be free from defects in material or
workmanship, under normal use and service for
accordance with the Goldline installation instructions and specifications provided with the product. If written proof of the date of
the initial system installation is not provided to Goldline, the manufacturing datecode on the product or part will be the sole
determinant of the date of the initial system installation.

If a product is defective, in workmanship or materials and is removed and returned freight prepaid within one (1) year after the date
of the initial system installation, Goldline will, at its option, either repair or replace the defective product and return it freight prepaid.
The costs incurred in removal and/or reinstallation of the product are NOT covered under this warranty.

one year from date of the initial system installation, provided it is installed in

Warranty exclusions:

1. Material supplied or workmanship performed by others in the process of installation

2. Damage resulting from improper installation including installation on pools larger than the product rating.

3. Problems resulting from failure to operate the products in accordance with recommended instructions contained in product’s
owners manual.

4. Problems resulting from failure to maintain pool water chemistry in accordance with recommended levels.

5. Problems resulting from tampering, accident, abuse, negligence, unauthorized repairs or alterations, fire, flood, lightning,
freezing, external water, war, or acts of God.

THE EXPRESS LIMITED WARRANTY ABOVE CONSTITUTES THE ENTIRE WARRANTY OF GOLDLINE CONTROLS,
INC. WITH RESPECT TO ITS POOL AUTOMATION AND CHLORINATION PRODUCTS AND IS IN LIEU OF ALL
OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL GOLDLINE CONTROLS, INC. BE RESPONSIBLE FOR ANY
CONSEQUENTIAL, SPECIAL OR INCIDENTAL DAMAGES OF ANY NATURE WHATSOEVER.

NO WHOLESALER, AGENT, DEALER, CONTRACTOR, OR OTHER PERSON IS AUTHORIZED TO GIVE ANY WAR­RANTY ON BEHALF OF GOLDLINE CONTROLS, INC. THIS WARRANTY IS VOID IF THE PRODUCT HAS BEEN
ALTERED IN ANY WAY AFTER LEAVING THE FACTORY.

36

TEST IDEAL RANGE ADJUSTMENT REQUIRED

Free Chlorine 1.0 - 3.0 ppm Turn output dial up to increase,

pH 7.2 - 7.6

down to decrease -OR- increase
or decrease pump filtration time.

Too high - add muriatic acid
Too low - add soda ash.

Alkalinity 80 - 120 ppm

Salt 2700 - 3400 ppm Add salt as required to increase.

Stabilizer 60 - 80 ppm Add cyanuric acid to increase.

Calcium 200 - 400 ppm Add calcium to increase.

Electrolytic Cell inspect & clean Refer to section in manual.

Add baking soda to increase.

Add acid as required to decrease.

Drain and add water to decrease.

G

LD

ON

C

North Kingstown, RI 02852 USA

TROLS

LINE

INC

.

092043D

Copyright © 2004 Goldine Controls, Inc