Goldair GPORD02-24 User Manual

General Care and Safety Guide

Thank you for choosing a Goldair product. This Goldair unit has been designed and manufactured to high standards of engineering and with proper use and care, as described in this leaflet, will give you years of useful service.

Please read these instructions carefully and retain them for future use.

1.Use only the voltage specified on the rating label of the unit.

2.Keep all objects at least 1 metre from the front and 150mm from the ends and sides of the heater.

3.This unit is intended for household use only and not for commercial or industrial use.

4.Use this unit only as described in this manual. Any other use is not recommended by the manufacturer and may cause fire, electric shock or injury.

5.The common cause of overheating is deposits of dust or fluff in the unit. Ensure these deposits are removed regularly by turning off the unit and vacuum cleaning around the unit.

6.Always unplug unit when not in use.

7.When the unit has been unpacked, check it for transport damage and ensure all parts have been delivered. If parts are missing or the unit has been damaged, contact the Goldair Customer Services Team.

8.If your unit does not work, or is not working properly, contact the place of purchase or the Goldair Customer Services Team.

9.Do not connect the unit to mains supply until completely assembled and adjusted.

10.Ensure hands are dry before handling the plug or main unit.

11.Do not locate the unit directly below any power socket outlet.

12.Ensure heater is on a stable heat-resistant surface.

13.Do not operate with cord set coiled up as a heat build up is likely, which could be sufficient to become a hazard.

14.Carry out regular checks of the supply cord to ensure no damage is evident.

15.Do not operate this unit with a damaged cord, plug or after the unit malfunctions or has been dropped or damaged in any manner. Return to a qualified electrical person for examination, electrical service or repair.

16.Do not twist, kink or wrap the cord around the unit, as this may cause the insulation to weaken and split. Always ensure that all cord has been removed from any cord storage area and is unrolled before use.

17.It is recommended that this heater is plugged directly into the wall socket or installed by a registered electrician in accordance with AS/NZS 3000:2007.

18.Do not remove plug from power socket until the unit has been switched off.

19.Do not remove plug from power socket by pulling cord; always grip plug.

20.Arrange the cord so it cannot be tripped over.

21.Do not place unit close to radiant heat source.

22.Never use the unit to dry clothes.

23.Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause an electric shock, fire or damage to the unit.

24.Do not sit on the unit.

25.Do not use abrasive cleaning products on this unit. Clean with a damp cloth (not wet) rinsed in hot soapy water only. Always isolate the unit from the mains supply before cleaning.

26.Do not operate in areas where petrol, paint or other flammable liquids are used or stored.

27.This unit is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they are supervised or have been given instruction concerning the use of the unit by a person responsible for their safety.

28.Children should be supervised to ensure that they do not play with the unit.

29.Do not use this unit in the immediate surrounds of a bath, a shower, or a swimming pool or other liquids. The unit must not be immersed in any liquids.

30.There are no user serviceable parts installed in the unit.

31.Do not place the unit in wardrobes or other enclosed spaces as this may cause fire hazards.

32.This unit is not supposed to be used in or around locations where foodstuffs, works of art or delicate articles of science, etc are stored.

33.WARNING you must not cover this heater. Covering this heater presents fire risk and will activate the safety fuse; permanently disabling the unit.

34.Do not use this heater with a programmer, remote-control system, separate timer or any other device that switches the heater on automatically since a fire risk exists if the heater is covered or positioned incorrectly.

TECHNICAL SPECIFICATION

Model No:	GPORD02-18	GPORD02-24	GPORD02-30
Supply:	220-240VAC 50/60Hz	220-240VAC 50/60Hz	220-240VAC 50/60Hz
Wattage:	1800W	2400W	3000W

Before Installing Your Radiant Heater

It is recommended that these heaters are installed by a registered electrician in accordance with AS/NZS3000:2007.

The GPDOR02-30 (3000W) model must either be hardwired or fitted with a 15 amp plug (not supplied) by a registered electrician.

Always choose a safe location for the heater, keeping in mind the safety precautions outlined.

WARNING: Keep all objects at least 1 metre from the front and 150mm from the ends of the heater.

Ensure all packaging has been removed from the unit before use.

WARNING: In order to avoid overheating, do not cover the heater.

WARNING: Never leave this heater unattended when powered on.

Unit Measurements
Model No: GPORD02-18	L1200 x W150 x H65mm	7.5kg
Model No: GPORD02-24	L1500 x W150 x H65mm	9.0kg
Model No: GPORD02-30	L1800 x W150 x H65mm	12.0kg

SUPPORT AND TECHNICAL ADVICE

Goldair – New Zealand	Goldair – Australia
Monday – Friday 8am-5pm	Monday – Friday 8am-5pm
Phone [phone]	Phone [phone]
Phone [phone]	Phone [phone]
[e-mail]	[e-mail]