Compact Filter
User Manual
Version 0.8
Copyright Glowforge, Inc. 2020 |
1 |
Introduction
You already know about the incredible things you can do with a Glowforge 3D laser printer. With a Compact Filter, you can do those things anywhere.
But before you can do any of that, you’ll need to read the information in this manual.
Our job is to make sure that every part of your Glowforge experience is delightful. Unfortunately, right now you’ll need to read a few pages that are not delightful: the Compact Filter safety information. They’re a little dry, and a bit scary. The safety section was written by our safety team, in the most direct language possible, to make absolutely certain you can operate your Compact Filter safely.
After the safety talk, we’ll get back to the fun part: unboxing, simple setup... and step by step instructions for how to use your Compact Filter during laser time!
PS: If you see anything that is unclear or seems incorrect, please let us know immediately at support@glowforge.com.
Copyright Glowforge, Inc. 2020 |
2 |
Safety
Now, it’s time to be serious. Improperly operating the Compact Filter unit can cause fire and health hazards. These can result in serious injury or even death.
Before you start
●Read this manual before using your Compact Filter, and ensure everyone else who uses it reads this too.
●Always follow all instructions in this manual, in the Glowforge Manual and in the Glowforge App.
●Use the Compact Filter only with a Glowforge Basic, Plus, or Pro.
●Children require the supervision and assistance of an adult at all times.
●This product may be subject to regulations and standards, particularly when installed in an educational institution or place of work. Ensure that you comply with all applicable rules.
Electrical Safety
To reduce the risk of electric shock or fire:
●Do not try to service, repair, or modify the Compact Filter in a manner not described in this manual.
●Do not open any sealed portion of the Compact Filter or try to access the wiring. Damage caused by opening the case is not covered by the warranty.
●If the Compact Filter or its power cord is damaged, unplug the power cord and contact support@glowforge.com immediately.
●In the event of any emergency or malfunction, unplug the power cord on the back of the unit.
●Use only a properly grounded 120 VAC outlet that meets local building codes.
●The Compact Filter may draw up to 3 amps. Ensure that the circuit can support at least a 350 watt load. Note: a standard 15A household outlet can support both a Glowforge printer and a Compact Filter if nothing else is drawing power from the circuit.
Copyright Glowforge, Inc. 2020 |
3 |
General Safety
●If you detect a strong, sharp smell that also causes eyes, nose, or throat irritation, or if there is visible smoke escaping your Glowforge printer while the lid is closed, your Compact Filter is not operating properly. Follow all instructions in this manual. If the irritation and/or smoke emissions do not abate, discontinue using your Compact Filter and contact support.
●Do not disconnect the hose, open the case, touch anything inside, or perform any maintenance or operations while the Compact Filter is plugged in.
●The Compact Filter has sparking parts inside. Do not use in areas where gasoline, paint, flammable liquids, or gases are used or stored.
●Do not use the Compact Filter without a Filter Cartridge.
●Do not plug in the Compact Filter while the lid is open or the latches are not fully engaged. Doing so could cause electric shocks or physical harm from moving parts.
●Do not use the Compact Filter when the Filter Cartridge is clogged. This will shorten the life of the machine and and any resulting damage caused is not covered by your warranty.
●Do not modify a Filter Cartridge for any reason.
●Use only with Filter Cartridges manufactured by Glowforge for use with this Compact Filter.
Operating Environment
To prolong the life of your Compact Filter and to reduce the risk of fire or mechanical failure:
●Do not use if the ambient temperature is below 40 degrees Fahrenheit (5 Celsius) or over 120 degrees Fahrenheit (48 Celsius).
●Do not use if the ambient air is below 40% humidity or above 80% humidity. Air above 80% humidity can clog the filter which may cause damage.
●Do not use the Compact Filter outdoors.
●Do not use the Compact Filter in an environment where it may come into contact with liquids, moisture, grease, or excessive dust or small particles.
Materials
●Use your Compact Filter only when printing on material that is laser compatible. Only the manufacturer or supplier of material can confirm that it is laser compatible. Glowforge recommends the use of Proofgrade™ materials with the Compact Filter.
●Non-laser compatible materials may contain harmful or toxic chemicals that are not treated by the Compact Filter and could cause injury or death.
Copyright Glowforge, Inc. 2020 |
4 |
●Non-laser compatible materials may cause damage to your Compact Filter.
●Some laser-compatible materials, such as MDF or Proofgrade Draftboard, may cause the Filter Cartridge to need replacement more frequently.
●Damage resulting from the use of non-laser compatible materials is not covered by the Compact Filter warranty.
Compact Filter Regulatory Information
This product conforms to applicable CE requirements and RoHs. It is suitable for use with Glowforge Basic, Plus, and Pro 3D laser printers.
Specifications
The Compact Filter has the following specifications:
|
Compact Filter |
|
|
|
|
Air Inlet Interface |
100mm diameter Flange |
|
|
|
|
Input Voltage |
AC110V |
|
|
|
|
Maximum Power |
350W (3A) |
|
|
|
|
Filtering Efficiency |
0.3μm 99.97% |
|
|
|
|
Noise |
70dB |
|
|
|
|
Systemic Flow |
350m³/h |
|
|
|
|
Dimensions of |
L410×W265×H430mm |
|
Main Unit |
||
|
||
|
|
|
Weight |
22.0kg |
|
|
|
The Compact Filter is manufactured by:
Glowforge, Inc.
2200 1st Avenue South, First Floor Seattle, WA 98134
For more information or support, contact support@glowforge.com
Copyright Glowforge, Inc. 2020 |
5 |
Labeling
This label appears on the back of every Compact Filter, with an appropriate serial number, in the spot indicated by the arrow in the diagram below.
Manufacturer's label |
Rear view of unit |
Getting Started
Now that you’ve read all about Safety, you’re ready to get lasering!
Unboxing will take just a few minutes – we can’t wait for you to get started either. Of course, if you encounter any challenges along the way, our Customer Success team can be reached at support@glowforge.com to help.
Let’s get started, shall we?
Check for damage
If your packaging or any part of your Compact Filter shipment is visibly damaged on arrival, we want to make it right as soon as possible! Send photos of the damage to support@glowforge.com and wait until you hear back from us. If the Compact Filter itself is visibly damaged, do not plug it in or attempt to operate it; contact us immediately.
Copyright Glowforge, Inc. 2020 |
6 |
Unbox your Compact Filter
Locate your Compact Filter.
Your Compact Filter must be on a flat surface, like the floor. It needs to be positioned so that the 8 foot exhaust hose can connect to the back of your Glowforge while making no more than three 90-degree bends.
Your Compact Filter blows air out, so ensure that there are no obstructions within two inches of the vents on either side.
Vents are on two opposite sides
Unseal your Compact Filter box.
Carefully cut tape sealing the top of your Compact Filter box and open it. Remove the power cord and the top piece of foam.
Copyright Glowforge, Inc. 2020 |
7 |