Global Industrial 246721 User Manual

Infrared Patio Heater,
Wall/ Ceiling Mount
User Manual
Model 246721
Read this manual thoroughly prior to installation and operation.
Keep these instructions in a safe location for future reference.
SAFETY INFORMATION
TO AVOID RISK OF SERIOUS INJURY OR DAMAGE, READ AND FOLLOW ALL SAFETY PRECAUTIONS, OTHERWISE WARRANTY WILL BE VOIDED.
WARNING: To prevent overheating, keep the air inlets and outlets clean and free of anything that may cause blockage. Often check all inlets and outlets to ensure they are clear of any dirt or dust accumulation. DO NOT COVER.
WARNING: Parts of the heater may exceed 390ºF, contact with the heating tube, reflector, or mental parts near the heating tube, may cause severe BURNS. DO NOT let bare skin touch hot surfaces. Switch off, unplug and allow the heater to completely cool off before making contact.
WARNING: If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet from the front of the heater and keep them away from the sides and rear.
DO NOT insert fingers or objects into any of the openings.  Keep all objects a minimum of 3-ft. away from the heater.  DO NOT cover the heater, or put objects such as fabrics or combustible materials in contact with the heater.  DO NOT allow children to play with the appliance. Keep children away unless continuously supervised.  Check that the voltage in the rating label fits the power supply.  The use of these heaters is forbidden in any area where there is a presence of gases, explosives or
inflammable objects.
Neither the connecting cable nor any other object must come into contact with the heater.  This heater should be switched off at the isolating switch before maintenance or repair work.  Installation must be carried out by a qualified installer in accordance with current local electrical regulations.  The heater must not be installed just below an electrical socket-outlet.  Never touch the heater with wet or humid hands or while barefoot.
DO NOT expose to direct rain/snowfall.
Model:
246721
Voltage:
110-120 VAC
Wattage:
1500W
Hertz:
60Hz
Application:
Outdoor
Dimensions:
18-1/8” L x 3”W x 7-1/2”H
Weight:
4.9 lbs.
The supply circuit must incorporate a double-pole isolating switch having a contact separation of at least
1/8”.
DO NOT operate if the power cord or plug is damaged, after a malfunction, or after the unit has been
dropped or damaged in any manner. Disconnect power and have the heater inspected by a reputable electrician before reusing.
Connect to properly grounded outlets only.  It is important to maintain a minimum distance of 3-feet between the heater and curtains, or any other
combustible materials that will be affected by the radiated heat.
DO NOT touch the fireguard or reflecting cover when the heater is in use; do not insert any objects into the
fireguard to prevent high temperature scalding.
Heater for outdoor use only.  Outdoor weatherproof outlet is recommended.  NEVER leave the heater unattended while it is operating.  DO NOT run cord under carpeting, throw rugs, runners, or similar coverings. Do not route cord under
furniture or appliances. Arrange cord away from high traffic areas and where it will not be tripped over.
DO NOT let the power cable hang over the edge of a table/counter or let it come in contact with hot
surfaces.
DO NOT use an extension cord.  To disconnect heater, turn controls to off, then remove plug from outlet.  Disconnect heater during installation and maintenance.  NEVER place hands under the heating elements. ALWAYS allow heating element to cool at least 10
minutes before touching the heating tube or adjacent parts.
The heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or
flammable liquids are used or stored.
NEVER dismantle the components of the heater or replace with components not offered or recommended
by Global Industrial.
SPECIFICATIONS:
INSTALLATION
Tools Required:
1. Power Drill and Drill Bits
2. Phillips Head Screwdriver
3. Hammer
4. Level
5. Pencil
A wall mounting bracket is provided with the heater. Before drilling holes make sure the mounting surface (ceiling or wall) is solid and that there are no hidden water pipes or electric wires behind it. Allow a minimum of 1-5/8 ft. from each side of the heater to the wall and 5-7/8 ft. off the floor.
WARNING: The heater must be installed on the solid surfaces like concrete, wood or metal, etc.
Loading...
+ 3 hidden pages