Global Industrial 246105 User Manual

globalindustrial.ca

User's manual Manual del usuario Manuel de l'utilisateur

Customer Service

US: 1-800-645-2986

Servicio de atención al Cliente

US: 1-800-645-2986

Service à la clientèle

Canada: 888-645-2986

Energy Efficient Portable Dehumidifier

Model 246105

30 Pint Dehumidifier

Model 246106

50 Pint Dehumidifier

Model 246107

70 Pint Dehumidifier

Model 246108

70 Pint Dehumidifier

w/Built-in Pump

WARNING

• DO NOT allow children or non-qualified persons
operate this dehumidifier.

• Disconnect unit from its power source before cleaning,
maintenance, servicing or replacing parts.

•

Disconnect all supply circuits before accessing terminals.

• NEVER attempt to plug in or operate dehumidifier with
defective or damaged wires, power cord, or power
cord plug. All defective parts should be replaced
immediately by a qualified service technician using
genuine replacement parts.

• Check the nameplate for the type of refrigerant gas used
in the appliance. Maintenance and disposal operations
must be carried out by qualified personnel only.

• This hermetically sealed system contains fluorinated
Greenhouse gases covered by Kyoto Protocol.

• DO NOT damage the cooling circuit of the machine.

• DO NOT use this unit for functions other than those
described in this manual.

• Ensure power plug is firmly and completely plugged
into the outlet. Doing so will avoid risk of electric shock
or fire.

• DO NOT plug other appliances into the same outlet.
Doing so may result in the risk of electric shock.

Please read entire manual
carefully before use. Save

manual for future reference.

• DO NOT disassemble or modify the appliance or any
of its parts. Doing so may result in the risk of electric
shock or fire. All services should be referred to a
qualified technician.

• DO NOT place the power cord or dehumidifier near a
heater, radiator, or other heat source. Doing so may
result in the risk of electric shock or fire.

• This unit is equipped with a cord that has a grounded
wire connected to a pin or grounding tab. The plug
must be plugged into a socket that is properly installed
and grounded. DO NOT under any circumstances cut
or remove the grounded pin or grounding tab from
the plug.

• The unit should be used or stored in such a way that it
is protected from moisture, condensation, water, etc.

• ALWAYS transport your appliance in a vertical position
and place on a stable, level surface during use. If the
unit is transported on its side it should be stood up and
left unplugged for 6 hours prior to use.

• ALWAYS use the power switch on the control panel or
remote control to turn the unit on/off. DO NOT start or
stop operation by plugging or unplugging the power
cord. Doing so can result in the risk of electric shock.

• DO NOT press the buttons on the control panel with
anything other than your fingers.

1

062019

Energy Efficient Portable

Dehumidifier

User's Manual

• DO NOT use hazardous chemicals to clean or come into
contact with the unit. To prevent damage to the surface
finish, use only a soft cloth to clean the appliance.
DO NOT use solvents, or strong detergents.

• DO NOT use the unit in the presence of flammable
substances or vapors such as alcohol, insecticides,
or gasoline.

• If the appliance is making unusual sounds or is emitting
smoke or an unusual odor, unplug it immediately.

• DO NOT clean the unit with water. Water can enter
the unit and damage the insulation, creating a shock
hazard. If water enters the unit, unplug it immediately
and contact Global Industrial Customer Service at
1-800-645-2986.

• Utilize two or more people to lift and install the unit.

• Be sure all accessories are removed from the packaging
before installation and use.

• Avoid contact with the metal parts of the appliance
when removing or re-installing the filter.

• DO NOT block the air inlet or outlet of the dehumidifier.
Reduced air flow will result in poor performance and
could damage the unit.

• ALWAYS grasp the plug when plugging or unplugging
the unit. Unplugging the unit by pulling on the cord can
run the risk of electrical shock and damage.

• Install the dehumidifier on a sturdy, level surface
capable of supporting up to 110 lbs. (50kg). Installation
on a weak or non level surface can result in the risk of
property damage and personal injury.

• Close all doors and windows to the room for
efficient operation.

CAN ICES-3 (B)/NMB-3(B)

FCC CAUTION:
This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation. Any changes or modifications not expressly
approved by the party responsible for compliance could
void the user's authority to operate the equipment.

any circumstances, be cut or removed. Never use the
cord, the plug or the appliance when they show any sign
of damage. Do not use your appliance with an extension
cord unless it has been checked and tested by a qualified
electrical supplier. Improper connection of the grounding
plug can result in risk of fire, electric shock and/or injury
to persons associated with the appliance. Check with
a qualified service representative if in doubt that the
appliance is properly grounded.

ELECTRICAL CONNECTIONS

Before plugging the appliance into outlet check that:

• The power supply corresponds to the value indicated
on the rating plate on the back of the dehumidifier.

• The power outlet and electrical circuit are adequate for
the dehumidifier.

• The outlet matches the plug. If this is not the case, have
the plug replaced.

•

The outlet is adequately grounded. Failure to follow
these important safety instructions may result in injury or
damage and exempts Global Industrial of all liability.

Check local regulations for proper
waste disposal procedures. As a
reminder of the need to dispose of
household appliances separately,
the product is marked with a
crossed-out wheeled dustbin.

NOTES ON HUMIDITY

Air always contains a certain amount of water in the
form of vapor. This determines the level of humidity in an
atmosphere. The capacity of the air to hold water vapor
increases with temperature. This is why in our homes, as
soon as the temperature decreases, the vapor contained in
the air condenses. This is evident on the colder surfaces in
the room, such as the windows, walls, etc. The purpose of a
dehumidifier is to remove the excess moisture from the air,
avoiding damage caused by condensation.

Experts have established that the optimum environmental
conditions for our well-being and for the home are
between 40% and 60% relative humidity. In low
temperatures, it is recommended to heat the room
minimally. This considerably increases the dehumidifying
power of the appliance. With heating, the condensation
formed by the water vapor on windows and other cold
surfaces evaporates into the air to be collected by the
dehumidifier. Air leaving the dehumidifier is usually about
1-2° warmer than room temperature.

IMPORTANT - GROUNDING METHOD

This product is factory equipped with a power supply
cord that has a three-pronged grounded plug. It must
be plugged into a mating grounding type receptacle
in accordance with the National Electrical Code and
applicable local codes and ordinances. If the circuit
does not have a grounding type receptacle, it is
the responsibility and obligation of the customer to
exchange the existing receptacle in accordance with the
National Electrical Code and applicable local codes and
ordinances. The third ground prong should not, under

2

COMPONENT BREAKDOWN

User's Manual

Energy Efficient Portable

Dehumidifier

1

2

6

7

1 Control Panel
2 Air Outlet
3 Bucket
4 Water Level Indicator
5 Casters

8

3

6 Handle
7 Air Intake Grille

4

8 Drainage Holes
9 Power Cord

5

9

*Note: All illustrations in this manual are for explanatory
purposes only. Your unit might look slightly different.

Before using, remove all accessories from the bucket: Detach the bucket, open the cover, remove the plug and all other
accessories. Reinstall the cover, and correctly reattach the bucket into the dehumidifier.

Accessories Included:

Casters (4)

Pump Adapter

Casters (4)

Plug

Pump Adapter
(for model 246108 only)

Drain Hose
(for model 246108 only)

Attaching the Casters

Tilt the unit no more than 45°
and insert the casters with
force. Make sure the plate of
the casters is flush against the
bottom of the unit.

1

F F

E ED DC CGB BA A

The above figure is for models 246105, 246106, & 246107 (without pump) The above figure is for model 246108 (with pump)

A ≤ 45°

Plate on

Caster

12

23 384 5 476 5 6 7

PUMP

PUMP

1 Clean Filter Symbol 5 Timer "On" Symbol A On/Off Button E Fan Speed Button
2 High Fan Speed Symbol 6 Bucket Full Alarm B Timer Button F Filter Reset Button
3 Display Screen 7 Continuous Symbol C Decrease Button G Pump Button
4 Timer "Off" Symbol 8 Pump Symbol D Increase Button

3

Energy Efficient Portable

Dehumidifier

User's Manual

On/Off power supply is used to control the start-up or

shut down of the dehumidifier.

Increase and decrease the indoor humidity level,

or set the time.

• Humidity adjustable range is 35%RH-80%RH. The
screen will display the setting humidity, and after few
seconds, turn to display the ambient humidity.

• When the ambient humidity is lower than the set
humidity, the compressor will stop running and after a
few minutes, the fan will stop running.

• To continuously run, press the button until
is displayed on the screen and the continuous
symbol lights up.

Fan speed is used to select the speed from Low to

High. Speed is on high when the symbol lights up.

T

imer button is used to to delay start-up or shutdown.

This avoids wasting electricity by optimizing operating periods.

PROGRAMMING START-UP

• Turn machine on and choose mode; for example:
Dehumidify Mode, High Fan Speed. Turn machine off.

• Press Timer Button, the screen will begin to flash. Press
the buttons to adjust the set-time from 0.5 to
24 hours.

• After 5 seconds without operation, the timer will begin
and the symbol will light up.

• To cancel Timer, press Timer button again and the
will disappear.

BUCKET FULL ALARM

• When the bucket is full, the compressor will shut-off
and after a few minutes the fan will stop. The machine
will begin to beep and the bucket full symbol
will flash.

• The unit will not run again until the bucket is emptied
and properly placed back inside the dehumidifier.

• Clean the bucket weekly to prevent growth of mold,
mildew and bacteria. Use a mild detergent to clean.
Ensure bucket is completely dry before reinstalling
back into dehumidifier.

• NOTE: Hold the bucket with both hands when emptying.

• NOTE: When the bucket is full or removed from the unit,
the compressor will turn off but the fan will continue to
run for a few minutes. This is completely normal; the
machine will not be removing moisture from the air at
this time.

• NOTE: During normal operation, the humidifier will
exhaust warm air from the top of the unit.

• CAUTION: DO NOT place the bucket on the floor when
full as bottom is uneven and may cause spillage.

AUTOMATIC DEFROST

When frost builds up on the evaporator coils, the compressor
will cycle off and the fan will continue to run until the
frost disappears. When the coils are completely defrosted,
the compressor or fan (depending on the model) will
automatically restart and dehumidification will resume.

CONTINUOUS DRAINAGE

Using Built-In Pump (Model 246108 Only)

Drain Adapter

• Connect the drain pipe on the
back of the dehumidifier; this will
allow the unit to run continuously
without the use of the bucket.

1. Place the dehumidifier on a level

surface and unscrew the cap on
the back of the unit.

2. Install the drain and gasket connector.

3. Install the drain pipe to the connector.

4. Press Power button to run the

unit. For Model 246108 Pump Drain:

5. Press the “PUMP” button to start the pump drain

function, and the “PUMP” symbol will light up. The
maximum height of pump drainage is 16.4 ft (5 meters).

Seal Ring

Drain Hose

MAX. 5m (16.4 ft.)

CONTINUOUS DRAIN HOSE ROUTING

Without Pump (All Models)

1. Connect 1
onto the units drain hole.

2. Make sure hose is installed correctly, otherwise the
water will not drain properly, (see image below).

3. Use gravity to drain water to a nearby drain or other
location.

Correct Incorrect

• If the continuous drain function is not needed, install the

cap on the drain hole on the back of the unit and the
water will flow into the bucket.

NOTE: Ensure the unit is placed on a level surface,
otherwise the water will not drain properly.

1

/16" threaded garden hose (not included)

4

Energy Efficient Portable

Dehumidifier

User's Manual

LOCATION REQUIREMENTS

Note: Basement operation will have little to no effect in
drying out an adjacent enclosed area, such as a closet,
unless there is adequate circulation of air in and out
of the area.

YES NO

Above

5°C

41°F

18"

Below

5°C

41°F

CLEANING AND MAINTENANCE

WARNING

Before cleaning and maintenance, turn the power off
on the control panel of the dehumidifier. Wait a few
minutes then unplug the unit from the outlet. Not doing
so increases the risk of electric shock or fire.

The dehumidifier’s water collection tank must be cleaned
with soap and warm water or a mild detergent frequently.
Mold and mildew can build up quickly, and when inside
a dehumidifier tank, it can get dispersed into the air,
affecting air quality.

Several times a season, use a vacuum with a brush
attachment to clean the intake and exhaust grilles. Dust
and debris build-up can cause blockages that can lead to
deterioration of the unit.

Cleaning Filter

To keep the appliance working efficiently, it is recommended
to clean the filter every week of operation:

• Use a vacuum with a brush attachment to remove dust

accumulation from the filter.

• If filter is very dirty, immerse it in warm water and rinse

several times. The water temperature should never be
hotter than 104°F (40°C). Allow filter to fully dry before
reattaching back to the dehumidifier.

18"

18"

• This unit is designed for indoor use only.

• Place the dehumidifier on a level floor surface that is
strong enough to support the unit with a full bucket
of water.

• Allow at least 18 inches of air flow on all sides.

• Place the unit in an area where the temperature will not
fall below 41°F (5°C).

•

Utilize the dehumidifier in areas of excessive moisture, such
as basements, kitchens, laundry rooms and bathrooms.

• Keep dehumidifier away from clothes dryer.

• The dehumidifier must be operated in an enclosed area
to be most effective. Close all doors, windows and any
other outside openings for best results.

End of Season Maintenance and Storage

• T urn off power and unplug from outlet.

• Empty the bucket.

• Remove cap and drain remaining water into a basin.

• When all water has been drained, put the cap back
in place.

• Clean filter and dry thoroughly before reinstalling.

• Cover the appliance for dust protection.

• Store the dehumidifier upright in a dry location.

Start of Season Checks

• Inspect dehumidifier for signs of damage.

• Inspect power cable and plug for signs of damage.

• Follow the installation instructions precisely.

• Please contact Global Industrial Customer Service at
1-800-645-2986 for questions and inquiries.

5

TROUBLESHOOTING

Problem Possible Cause Solution

Energy Efficient Portable

Dehumidifier

The dehumidifier is unplugged.

The fuse is blown/circuit breaker is tripped.

User's Manual

Make sure the dehumidifier's plug is pushed

completely into the outlet.

Check the house fuse/circuit breaker box

and replace fuse or reset breaker.

Dehumidifier does

not start.

Dehumidifier does

not dry air as it should.

Appliance runs

too long.

Dehumidifier has reached its present level

or the bucket is full.

Bucket is not in the proper position.

Power Failure.

Not enough time allowed for unit

to remove moisture.

Airflow is restricted.

Dirty filter

The humidity control may not

be set low enough.

Doors and windows may not

be closed tightly.

Clothes dryer may be blowing moist

air into the room.

Room temperature is too low.

The area is too large.

Doors and windows are open. Close all doors and windows.

The dehumidifier automatically turns off when

either condition occurs. Change to a lower setting

or empty the water bucket and replace properly.

The bucket must be in place and securely seated

for the dehumidifier to operate.

There is a protective time delay

(up to 3 minutes) to prevent tripping of the

compressor overload. For this reason, the unit

may not start normal operation for 3 minutes

after it is powered back on.

When first installed, allow at least 24 hours

to maintain the desired dryness.

Make sure there are no curtains, blinds, or

furniture blocking the front or back of the

dehumidifier. See the Location Requirements

section of this manual for more information.

See the Cleaning Filter section of this

manual for more information.

For drier air, press the button to lower the

percent humidity desired in the room, or set the
dehumidifier to for maximum dehumidify.

Check that all doors, windows, and other

openings are securely closed.

Install the dehumidifier away from the dryer.

The dryer should be vented outside.

Moisture removal is best at higher room

temperatures. Lower room temperatures

will reduce the moisture removal rate. This

dehumidifier is designed to operate at

temperatures above 5°C (41°F).

The capacity of the appliance cannot

meet the area of the room.

Frost appears on heat

exchanger.

Fan noise The air is passing through the appliance. This sound is normal.

Water on the floor.

Appliance has been operated recently or

the room temperature is too low.

Drain connections are not fastened properly.

dehumidifier is not on a level surface.

This is normal, frost usually disappears

within 60 minutes.

Check the drain connection for leaks and fasten

properly. Make sure the appliance is operating

on a level surface.

If any of the following error codes appear, contact a certified after-sales service department for inspection and/or
repair. For additional information, contact Global Industrial Customer Service at 1-800-645-2986.

Code Description

P1 Bucket Pull Out

EH Humidity sensor failure

E1

Temperature sensor failure

E2

• Code P1 applies to model 246108 (with pump) only.

•

If code E3 appears, check to see if the room temperature is above
90°F (32°C). If this is the case, relocate the dehumidifier in a location
below 86°F (30°C) and allow to sit for 2 hours before running again.
Start the unit again; if the E3 code still appears, contact a service
department or Global Industrial Customer Service at 1-800-645-2986
for further instructions.

E3 Gas leakage

6