Page 1
OPERATION INSTRUCTIONS
Parts List
Hand Pallet Truck
Note: Owner and operator MUST read and understand these
operating instructions before using this pallet truck.
Page 2
ATTENTION:
1. The waste packages should be sorted and put into solid dustbins according to the materials
and be collected disposal by local special environment protection bureau. To avoid pollution, it’s
forbidden to throw away the wastes randomly.
2. To avoid leaking during the use of the products, the user should prepare some absorbable
materials (scraps of wooden or dry duster cloth) to absorb the leaking oil in time. To avoid
second pollution to the environment, the used absorbable materials should be handed in to
special departments in terms of local authorities.
1
Page 3
Thank you for choosing our pallet trucks. For your safety and correct operation, please carefully
read the manual before use.
NOTE:
factory reserves the right to modify its own products at any time without notice or liability in any
sanctions. Please verify with the factory for possible updates and changes .
All of the information reported herein is based on data available at the time of printing. The
1. GENERAL SPECIFICATIONS
Capacity (kg) 2000
Maximum Fork Height (mm)
Minimum Fork Height (mm)
Fork Length (mm) 1150
Width Overall Forks (mm) 450 / 520 / 550 / 685
Individual Fork Width (mm) 160
Load Wheel Diameter (mm) Ø 80x70(or Ø 74x70) Nylon, Polyurethane
Steering Wheel Diameter (mm)
Special fork lengths are available in 800, 900, 950, 1000, 1220, 1500, 2000 mm.
Materials and specifications are subject to change without notice.
2. ATTACHING HANDLE TO PUMP UNIT
2.1 Remove 3 bolts (D611) from the handle bracket (D151).
2.2 Set handle (D610A, D610B or D610AS) on the bracket (D151), notice to allow the chain (D612)
and the adjusting bolts (D614) assembly to pass through the hole in the center of the bracket (D151)
and shaft (D153).
2.3 Insert the 3 bolts (D611) through the handle into the bracket (D151), then tighten them securely.
2.4 Raise the lever plat (D132) and insert the adjusting bolt (D614) into the front slot, keeping the
adjusting nut (D615) on the under side of the lever plat (D132).
200(or190)
85(or75)
Ø 200(or Ø 180) Nylon, Polyurethane, Rubber
3. ADJUSTING RELEASE DEVICE
On the draw-bar of this pallet truck, you can find the control handle (D608 or D608S) which can be
adjusted in three positions :
Raise - handle down
Drive - handle in center position
Lower - handle up, the lever moves back the drive position when released.
If however they have been changed, you can adjust according to the following steps:
3.1 If the forks elevate while pumping in the DRIVE position, turn the adjusting nut (D615) on the
adjusting bolt (D614) or adjusting screw (D133) clockwise until pumping action does not raise the
forks and the DRIVE position functions properly.
3.2 If the forks descend while pumping in the DRIVE position, turn the nut (D615) or adjusting screw
(D133) counter-clockwise until the forks do not lower.
3.3 If the forks do not descent when the control handle (D608 or D608S) is in the LOWER position,
turn the nut (D615) or adjusting screw(D133) clockwise until raising the control handle(D608 or
D608S) lowers the forks. Then check the DRIVE position according to item 3.1 and 3.2 to be sure
2
Page 4
the nut (D615) or adjusting screw (D133) is in the proper position.
3.4 If the forks do not elevate while pumping in the RAISE position, turn the nut (D615) or adjusting
screw(D133) counter-clockwise until the forks elevate while pumping in the RAISE position. Then
check the LOWER and DRIVE position according to item 3.1, 3.2 and 3.3.
4. MAINTENANCE
Your pallet truck is largely maintenance-free.
4.1 OIL
Please check the oil level every six months. The oil capacity is about 0.3lt. Use the hydraulic type
oil according to temperature scale below.
Temperature Oil
-20℃~+40℃
L-HV46 Hydraulic oil
4.2 EXPELING AIR FROM THE PUMP UNIT
The air may come into the hydraulic oil because of transportation or pump in upset position. It can
cause the forks unable to elevate while pumping while in the RAISE position. The air may escape in
the following way: let the control handle (D608 or D608S) on the LOWER position, then move the
handle (D610A, D610B or D610AS) up and down for several times.
4.3 DAILY CHECK AND MAINTENANCE
Daily check of the pallet truck can limit wear as much as possible. Special attention should be paid
to wheels, axles, thread, rags, etc. It may block the wheels. The forks should be unloaded and
lowered in the lowest position when the job is over.
4.4 LUBRICATION
Use motor oil or grease to lubricate all moveable parts.
5. GUIDE TO SAFETY OPERATIONS
For safe operation of the Hand Pallet Truck, please read all warning signs and instructions
here and on the pallet truck prior to use.
5.1 Do not operate the pallet truck unless you are familiar with it and have been trained or
authorized to do so.
5.2 Do not operate the truck unless you have been trained and authorized. Pay special attention to
the wheels, the handle assembly, the forks and the lower control.
5.3 Do not use the truck on sloping ground.
5.4 Never place any part of your body in the lifting mechanism or under the forks or load. Do not
carry passengers.
5.5 It is advisable that operators should wear gloves and safety shoes.
5.6 Do not handle unstable or loosely stacked loads.
5.7 Do not overload the truck.
5.8 Always place loads centrally across the forks and not at the end of the forks (See Fig. 2).
5.9 The capacity of the truck assumes an evenly distributed load with the center of the load being
3
Page 5
at the halfway point of the length of the forks.
No
Trouble
1
-
Inspect and replace the
5.10 Make sure that the length of the forks matches the length of the pallet.
5.11 Lower the forks to the lowest height when the truck is not being used.
5.12 In other specific conditions, the operators should take extra care in operating the truck.
6. TROUBLES SHOOTING
The forks can not be
lifted up to the
maximum height.
2
The forks can not be
lifted up.
3
The forks can not be
lowered.
4
Leaks
5
The forks towers
without the release
valve working.
*NOTE: DO NOT ATTEMPT TO REPAIR THE PALLET TRUCK UNLESS YOU ARE
TRAINED AND AUTHORIZED TO DO SO.
enough.
Without hydraulic oil
The oil has impurities
The nut (D615) is too high
Air come into the hydraulic
The piston rod (D147) or
The fork was kept in the
The adjusting nut (D615)
Sealing parts worn or
Some part cracked or
The impurities in the oil
Some parts of hydraulic
Air come into the oil.
Sealing parts worn or
The adjusting nut (D615)
CAUSE ACTION
The hydraulic oil is not
or the screw (D133) is too
close, keep the pumping
valve open
oil
pump body is deformed
resulting from partial
loading slanting to one
side or over-loading.
high position for long time
with piston rod bared to
arise in rusting and
jamming of the rod.
or the screw (D133) is not
in the correct position
damaged
worn into small
cause the release valve to
be unable to close tight.
system is cracked or
bored.
damaged
or the screw (D133) is not
in the correct position
- Pour in the oil.
Fill in the oil
Change the oil
Adjust the nut (D615) or the
screw (D133) .(see item
3.4)
Banish the air.(see item 4.2)
Replace the piston rod
(D147) or pump body
Keeping the fork in the
lowest position if not using,
and pay more attention to
lubricate the rod
Adjust the nut (D615) or the
screw (D133). (see item
3.3)
Replace with the new one
Replace with the new one
Replace with new oil
waste parts
Banish the air.(See item
4.2)
Replace with the new one
Adjusting the nut (D615) or
the screw (D133). (See item
3.2)
4
Page 6
5
Page 7
6
Page 8
No. Description
Qty.
No. Description
Qty.
1 D601 Spring 1 9 D609 Pull Board 1
2 D602 Blade Spring 1 10 D610B
Handle 1
3 D603 Roller 1 11 D611 Screw 3
4 D604 Elastic Pin 1 12 D612 Chain 1
5 D605 Elastic Pin 1 13 D613 Pin 1
6 D606 Elastic Pin 1 14 D614 Adjusting Bolt 1
7 D607 Elastic Pin 1 15 D615 Adjusting Nut 1
8 D608 Control Handle 1 16 D616 Elastic Washer 3
17 D101 Pump Piston Rod 1 46 D132 Lever Plat 1
18 D102 Washer 1 47 D133 Adjusting Screw 1
19 D103 Spring 1 48 D134 Nut 1
20 D104 Dust Ring 1 49 D135 O – Ring 1
21 D105 Y – Seal 1 50 D136 Axle Sleeve 1
22 D106B
23 D107B
Screw 1 51 D137 Adjusting Bolt 1
O – Ring 1 52 D139 Spindle of Safety Valve
1
24 D108 Spring 1 53 D140 Spring 1
25 D109 Spindle of Pumping Valve 1 54 D141 O – Ring 1
26 D110B Seat of Pumping Valve 1 55 D142 Screw 1
27 D111B
O – Ring 1 56 D143 O – Ring 1
28 D112 Steel Ball 1 57 D144 Y – Seal 1
29 D113 Base of Pump 1 58 D145 Elastic Pin 1
30 D115 Elastic Pin 1 59 D146 Steel Ball 1
31 D116 Steering Wheel 2 60 D147 Piston Rod 1
32 D117D Shaft of Steering Wheel 1 61 D148 Dust Ring 1
33 D118 Thrust Plate 1 62 D149 Screw 1
34 D119 Oil – holder 1 63 D150 Shaft 1
35 D120 Retaining Ring 1 64 D151 Bracket 1
36 D121 Cover of Bearing 1 65 D152 Pressure Roller 1
37 D122 Bearing 1 66 D153 Shaft 1
38 D123 Elastic Pin 2 67 D154 Elastic Pin 1
39 D124 Dust Cover 2 68 D155 Elastic Pin 1
40 D125D
41 D126D
Retaining ring 2 69 D156 Bushing 1
Tab Washer 2 70 D157 Seal Washer 1
42 D127 Bearing 4 71 D158 Bushing 2
43 D129 Spring 1 72 D159B
44 D130 Strike Pin 1 73 D160B
Sleeve 1
Screw 1
45 D131 O – Ring 2
74 D201 Screw 1 90 D217#
Shaft for Roller 4
75 D202 Oil - holder 1 91 D218 Fork Frame 1
76 D203 Rock – arm 1 92 D219 Washer 8 or 4
77 D204 Elastic Pin 1 93 D220 Bearing 8 or 4
78 D205 Retaining Ring 2 94 D221#
79 D206D
Joint 2 95 D222#
Loading Roller 4
Linking Plate 4
80 D207 Shaft 2 96 D223 Elastic Pin 8 or 2
81 D208D
82 D209D
Pushing Rod 2 97 D224 Bushing 4
Nut 2 98 D225 Bushing 2
83 D210 Pin 2 99 D226 Bolt 2
84 D211 Shaft 1 100 D227 Enter Roller 2
85 D212 Shaft 2 101 D228 Nut 2
86 D213 Elastic Pin 2 102 D229*
87 D214 Shaft 2 103 D230*
Loading Roller 2
Shaft for Roller 2
88 D215 Frame of Roller 2 104 D231 Washer 2
89 D216 Elastic Pin 2 105 D232 Washer 4
(Note # --For Tandem wheel, * --For single wheel)
7
Page 9
List of Assembly
No. Parts No.
Description
List of Assembly
Qty.
1 DF20-01 Handle Ass’y D601, D602, …, D610B, D612, …, D615 1
2 DF20-023 DF20-03 Chain Ass’y D609,D612,D613,D614,D615 1
4 DF20-04
5 DF20-05
6 DF20-06 Steering Wheel Ass’y
7 DF20-07 Seal Kit of Pump Unit
8 DF20-08 Bracket Ass’y D150, D151, D152, D154, D156 1
9 DF20-09 Pump Ass’y
Control handle kit D603, D605, D608 1
Load Roller
Ass’y(Single Type)
Load Roller
Ass’y(Tandem Type)
D104, D105, D107B, D111B, D131, D131, D135,
D141, D143, D144, D148, D157
D101, D102, D103, D104, D105, D106B, D107B,
D108, D109, D110B, D111B, D112, D113, D129,
D130, D131, D132, D133, D134, D135, D136,
D137, D139, D140, D141, D142, D143, D144,
D145, D146, D147, D148, D149, D150, D151,
D152, D153, D154, D155, D156, D157, D158,
D159B, D160B
D220, D220, D229 2
D220, D220, D221 4
D116, D127, D127 2
Option: Foot Brake
1
1
8
Loading...