H470M DS3H
User's Manual
Rev. 1001
12ME-H47MS3H-1001R
For more product details, please visit GIGABYTE's website.
To reduce the impacts on global warming, the packaging materials of this product are recyclable and reusable. GIGABYTE works with you to protect the environment.
Copyright
© 2020 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.
Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice.
No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission.
In order to assist in the use of this product, carefully read the User's Manual.
For product-related information, check on our website at: https://www.gigabyte.com
Identifying Your Motherboard Revision
The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0" means the revision of the motherboard is 1.0. Check your motherboard revision before updating motherboard BIOS, drivers, or when looking for technical information.
Example:
Table of Contents
H470M DS3H Motherboard Layout.................................................................................. |
4 |
|
Chapter 1 Hardware Installation...................................................................................... |
5 |
|
1-1 |
Installation Precautions..................................................................................... |
5 |
1-2 |
Product Specifications...................................................................................... |
6 |
1-3 |
Installing the CPU............................................................................................. |
9 |
1-4 |
Installing the Memory........................................................................................ |
9 |
1-5 Installing an Expansion Card.......................................................................... |
10 |
|
1-6 |
Back Panel Connectors.................................................................................. |
10 |
1-7 |
Internal Connectors........................................................................................ |
13 |
Chapter 2 BIOS Setup................................................................................................... |
22 |
|
2-1 |
Startup Screen................................................................................................ |
22 |
2-2 |
The Main Menu............................................................................................... |
23 |
2-3 |
Favorites (F11)................................................................................................ |
24 |
2-4 |
Tweaker.......................................................................................................... |
25 |
2-5 |
Settings........................................................................................................... |
30 |
2-6 |
System Info..................................................................................................... |
36 |
2-7 |
Boot................................................................................................................ |
37 |
2-8 |
Save & Exit..................................................................................................... |
40 |
Chapter 3 Appendix....................................................................................................... |
41 |
|
3-1 Configuring a RAID Set.................................................................................. |
41 |
|
3-2 Installing an Intel® Optane™ Memory.............................................................. |
43 |
|
3-3 |
Drivers Installation.......................................................................................... |
45 |
Regulatory Notices.................................................................................................... |
46 |
|
Contact Us................................................................................................................. |
48 |
- 3 -
KB_MS_USB ATX_12V_2X4
|
SYS_FAN1 |
|
|
DVI |
VGA |
|
|
DP |
HDMI |
|
|
U32C |
U32 |
|
|
U32_LAN |
Intel® |
|
|
|
|
GbE LAN |
|
|
110 |
80 |
60 |
AUDIO
|
PCIEX16 |
|
|
PCIEX1_1 |
BAT |
|
|
|
iTE® |
|
|
Super I/O |
PCIEX1_2 |
|
|
|
|
CODEC |
|
80 |
PCIEX4 |
|
|
|
|
|
|
|
CPU_FAN |
|
|
|
ATX |
|
|
|
|
|
|
|
|
|
|
LGA1200 |
|
|
|
|
|
|
|
|
|
|
|
|
SYS FAN2 |
|
|
|
|
|
|
|
3 2 |
|
|
|
|
|
|
|
1 0 |
|
|
|
|
|
|
|
SATA3 |
|
42 |
M2Q |
|
|
|
|
F U32 |
|
|
|
|
|
|
||
|
|
|
A1 |
A2 |
B1 |
B2 |
THBC2 THBC1 |
|
|
H470M DS3H |
DDR4 |
DDR4 |
DDR4 |
DDR4 |
|
|
|
|
|
|
|
|
|
|
|
M_BIOS |
|
|
|
|
|
|
|
|
M2P |
Intel® H470 |
SATA3 |
||
|
|
|
|
|
|
|
5 4 |
60 |
|
42 |
|
|
|
|
|
|
|
QFLED |
|
|
CLR_CMOS |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
LED |
|
_C1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
F_AUDIO COM |
LPT |
QFLASH_ |
|
|
F_USB1 |
SPI_TPM |
|
F_PANEL |
|||||||||
|
|
|
|
|
PLUS |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
D_LED1 |
|
F_USB2 |
|
SYS_FAN3 |
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
Box Contents
55 |
H470M DS3H motherboard |
55 |
Two SATA cables |
55 |
Motherboard driver disc |
55 |
I/O Shield |
55 |
User's Manual |
|
|
*The box contents above are for reference only and the actual items shall depend on the product package you obtain. The box contents are subject to change without notice.
-4 -
The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's manual and follow these procedures:
•• Prior to installation, make sure the chassis is suitable for the motherboard.
•• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or warranty sticker provided by your dealer. These stickers are required for warranty validation.
•• Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components.
•• When connecting hardware components to the internal connectors on the motherboard, make sure they are connected tightly and securely.
•• When handling the motherboard, avoid touching any metal leads or connectors.
•• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap, keep your hands dry and first touch a metal object to eliminate static electricity.
•• Prior to installing the motherboard, please have it on top of an antistatic pad or within an electrostatic shielding container.
•• Before connecting or unplugging the power supply cable from the motherboard, make sure the power supply has been turned off.
•• Before turning on the power, make sure the power supply voltage has been set according to the local voltage standard.
•• Before using the product, please verify that all cables and power connectors of your hardware components are connected.
•• To prevent damage to the motherboard, do not allow screws to come in contact with the motherboard circuit or its components.
•• Make sure there are no leftover screws or metal components placed on the motherboard or within the computer casing.
•• Do not place the computer system on an uneven surface.
•• Do not place the computer system in a high-temperature or wet environment.
•• Turning on the computer power during the installation process can lead to damage to system components as well as physical harm to the user.
•• If you are uncertain about any installation steps or have a problem related to the use of the product, please consult a certified computer technician.
•• If you use an adapter, extension power cable, or power strip, ensure to consult with its installation and/or grounding instructions.
- 5 -
1-2 |
Product Specifications |
|||
|
|
|
|
|
|
CPU |
|
Support for 10th Generation Intel® Core™ i9 processors/Intel® Core™ i7 processors/ |
|
|
|
|
Intel® Core™ i5 processors/Intel® Core™ i3 processors/Intel® Pentium® processors/ |
|
|
|
|
Intel® Celeron® processors in the LGA1200 package |
|
|
|
|
(Go to GIGABYTE's website for the latest CPU support list.) |
|
|
|
L3 cache varies with CPU |
||
|
Chipset |
|
Intel® H470 Express Chipset |
|
|
Memory |
|
Intel® Core™ i9/i7 processors: |
|
|
|
|
- |
Support for DDR4 2933/2666/2400/2133 MHz memory modules |
|
|
|
Intel® Core™ i5/i3/Pentium®/Celeron®processors: |
-Support for DDR4 2666/2400/2133 MHz memory modules
4 x DDR4 DIMM sockets supporting up to 128 GB (32 GB single DIMM capacity) of system memory
Dual channel memory architecture
Support for ECC Un-buffered DIMM 1Rx8/2Rx8 memory modules (operate in non-ECC mode)
Support for non-ECC Un-buffered DIMM 1Rx8/2Rx8/1Rx16 memory modules
Support for Extreme Memory Profile (XMP) memory modules
(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)
Onboard |
Integrated Graphics Processor-Intel® HD Graphics support: |
Graphics |
- 1 x D-Sub port, supporting a maximum resolution of 1920x1200@60 Hz |
|
- 1 x DVI-D port, supporting a maximum resolution of 1920x1200@60 Hz |
|
* The DVI-D port does not support D-Sub connection by adapter. |
|
- 1 x HDMI port, supporting a maximum resolution of 4096x2160@30 Hz |
|
* Support for HDMI 1.4 version and HDCP 2.3. |
|
- 1 x DisplayPort, supporting a maximum resolution of 4096x2304@60 Hz |
|
* Support for DisplayPort 1.4 version, HDCP 2.3, and HDR. |
|
- Support for up to 3 displays at the same time |
|
Maximum shared memory of 512 MB |
Audio |
|
Realtek® ALC887 codec |
|
High Definition Audio |
|
|
|
2/4/5.1/7.1-channel |
*Toconfigure7.1-channelaudio,youneedtoopentheaudiosoftwareandselectDevice advanced settings > Playback Device to change the default setting first. Please visit GIGABYTE's website for details on configuring the audio software.
LAN |
Intel® GbE LAN chip (1000 Mbit/100 Mbit) |
Expansion Slots |
1 x PCI Express x16 slot, running at x16 (PCIEX16) |
|
* For optimum performance, if only one PCI Express graphics card is to be installed, |
|
be sure to install it in the PCIEX16 slot. |
|
1 x PCI Express x16 slot, running at x4 (PCIEX4) |
|
2 x PCI Express x1 slots |
|
(All of the PCI Express slots conform to PCI Express 3.0 standard.) |
Multi-Graphics |
Support for AMD Quad-GPU CrossFire™ and 2-Way AMD CrossFire™ technologies |
Technology |
|
- 6 -
Storage Interface 1 x M.2 connector (Socket 3, M key, type 2242/2260/2280/22110 PCIe x4/x2 SSD support) (M2Q)
1 x M.2 connector (Socket 3, M key, type 2242/2260/2280 SATA and PCIe x4/ x2 SSD support) (M2P)
6 x SATA 6Gb/s connectors
Support for RAID 0, RAID 1, RAID 5, and RAID 10
*Refer to "1-7 Internal Connectors," for the installation notices for the M.2 and SATA connectors.
Intel® Optane™ Memory Ready
USB |
|
Chipset: |
|
|
- 1 x USB Type-C™ port on the back panel, with USB 3.2 Gen 1 support |
|
|
- 5 x USB 3.2 Gen 1 ports (3 ports on the back panel, 2 ports available through |
|
|
the internal USB header) |
|
|
- 6 x USB 2.0/1.1 ports (2 ports on the back panel, 4 ports available through |
|
|
the internal USB headers) |
Internal |
|
1 x 24-pin ATX main power connector |
Connectors |
|
1 x 8-pin ATX 12V power connector |
|
1 x CPU fan header |
|
|
3 x system fan headers |
|
|
1 x addressable LED strip header |
|
|
1 x RGB LED strip header |
|
|
2 x M.2 Socket 3 connectors |
|
|
6 x SATA 6Gb/s connectors |
|
|
1 x front panel header |
|
|
1 x front panel audio header |
|
|
1 x USB 3.2 Gen 1 header |
|
|
2 x USB 2.0/1.1 headers |
|
|
2 x Thunderbolt™ add-in card connectors |
|
|
1 x Trusted Platform Module header (For the GC-TPM2.0 SPI/GC-TPM2.0 SPI |
|
|
|
2.0 module only) |
|
1 x serial port header |
|
|
1 x parallel port header |
|
|
1 x Clear CMOS jumper |
|
|
1 x Q-Flash Plus button |
|
Back Panel |
|
1 x PS/2 keyboard/mouse port |
Connectors |
|
1 x D-Sub port |
|
1 x DVI-D port |
|
|
1 x HDMI port |
|
|
|
1 x DisplayPort |
1 x USB Type-C™ port, with USB 3.2 Gen 1 support3 x USB 3.2 Gen 1 ports
2 x USB 2.0/1.1 ports1 x RJ-45 port
3 x audio jacks
- 7 -
I/O Controller |
|
iTE® I/O Controller Chip |
||
Hardware |
|
Voltage detection |
||
Monitor |
|
Temperature detection |
||
|
Fan speed detection |
|||
|
|
Overheating warning |
||
|
Fan fail warning |
|||
|
Fan speed control |
|||
|
|
|
* Whether the fan speed control function is supported will depend on the cooler you |
|
|
|
|
install. |
|
BIOS |
|
1 x 256 Mbit flash |
||
|
Use of licensed AMI UEFI BIOS |
|||
|
PnP 1.0a, DMI 2.7, WfM 2.0, SM BIOS 2.7, ACPI 5.0 |
|||
Unique Features |
|
Support for APP Center |
||
|
|
|
* Available applications in APP Center may vary by motherboard model. Supported |
|
|
|
|
functionsofeachapplicationmayalsovarydependingonmotherboardspecifications. |
|
|
|
- |
@BIOS |
|
|
|
- |
EasyTune |
|
|
|
- |
Fast Boot |
|
|
|
- |
Game Boost |
|
|
|
- |
ON/OFF Charge |
|
|
|
- |
RGB Fusion |
|
|
|
- |
Smart Backup |
|
|
|
- |
System Information Viewer |
|
|
Support for Q-Flash Plus |
|||
|
|
Support for Q-Flash |
||
|
Support for Xpress Install |
|||
Bundled |
|
Norton® Internet Security (OEM version) |
||
Software |
|
cFosSpeed |
||
Operating |
Support for Windows 10 64-bit |
|||
System |
||||
|
|
|
||
Form Factor |
|
Micro ATX Form Factor; 24.4cm x 24.4cm |
*GIGABYTE reserves the right to make any changes to the product specifications and product-related information without prior notice.
Please visit GIGABYTE's website for support lists of CPU, memory modules, SSDs, and M.2 devices.
Please visit the Support\Utility List page on GIGABYTE's website to download the latest version of apps.
- 8 -
1-3 |
Installing the CPU |
|
|
Read the following guidelines before you begin to install the CPU: |
|
|
•• |
Make sure that the motherboard supports the CPU. |
|
|
(Go to GIGABYTE's website for the latest CPU support list.) |
|
•• |
Always turn off the computer and unplug the power cord from the power outlet before installing the |
|
•• |
CPU to prevent hardware damage. |
|
Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may |
|
|
•• |
locate the notches on both sides of the CPU and alignment keys on the CPU socket.) |
|
Apply an even and thin layer of thermal grease on the surface of the CPU. |
|
|
•• |
Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage |
|
•• |
of the CPU may occur. |
|
Set the CPU host frequency in accordance with the CPU specifications. It is not recommended |
|
|
|
that the system bus frequency be set beyond hardware specifications since it does not meet the |
|
|
standard requirements for the peripherals. If you wish to set the frequency beyond the standard |
|
|
specifications, please do so according to your hardware specifications including the CPU, graphics |
|
|
card, memory, hard drive, etc. |
Installing the CPU
Locate the alignment keys on the motherboard CPU socket and the notches on the CPU.
LGA1200 CPU Socket LGA1200 CPU
Alignment |
Alignment |
Notch |
Notch |
|
Key |
Key |
|||
|
|
|||
Pin One Corner of the CPU Socket |
|
Triangle Pin One Marking on the CPU |
|
Do not remove the CPU socket cover before inserting the CPU. It may pop off from the load plate automatically during the process of re-engaging the lever after you insert the CPU.
Read the following guidelines before you begin to install the memory:
•• Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips be used.
(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)
•• Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage.
•• Memory modules have a foolproof design. A memory module can be installed in only one direction. If you are unable to insert the memory, switch the direction.
Dual Channel Memory Configuration
This motherboard provides four memory sockets and supports Dual Channel Technology. After the memory is installed, the BIOS will automatically detect the specifications and capacity of the memory. Enabling Dual
Channel memory mode will double the original memory bandwidth.
Please visit GIGABYTE's website for details on hardware installation.
- 9 -
The four memory sockets are divided into two channels and each channel has two memory sockets as following:
Channel A: DDR4_A1, DDR4_A2Channel B: DDR4_B1, DDR4_B2
Recommanded Dual Channel Memory Configuration:
|
DDR4_A1 |
DDR4_A2 |
DDR4_B1 |
DDR4_B2 |
|
|
|
|
|
2 Modules |
- - |
DS/SS |
- - |
DS/SS |
4 Modules |
DS/SS |
DS/SS |
DS/SS |
DS/SS |
(SS=Single-Sided, DS=Double-Sided, "- -"=No Memory)
Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode.
1.Dual Channel mode cannot be enabled if only one memory module is installed.
2.When enabling Dual Channel mode with two or four memory modules, it is recommended that memory of the same capacity, brand, speed, and chips be used.
Read the following guidelines before you begin to install an expansion card:
•• Make sure the motherboard supports the expansion card. Carefully read the manual that came with your expansion card.
•• Always turn off the computer and unplug the power cord from the power outlet before installing an expansion card to prevent hardware damage.
USB 2.0/1.1 Port
The USB port supports the USB 2.0/1.1 specification. Use this port for USB devices.
PS/2 Keyboard/Mouse Port
Use this port to connect a PS/2 mouse or keyboard.
D-Sub Port
The D-Sub port supports a 15-pin D-Sub connector and supports a maximum resolution of 1920x1200@60 Hz (the actual resolutions supported depend on the monitor being used). Connect a monitor that supports D-Sub connection to this port.
DVI-D Port (Note)
The DVI-D port conforms to the DVI-D specification and supports a maximum resolution of 1920x1200@60 Hz
(the actual resolutions supported depend on the monitor being used). Connect a monitor that supports DVI-D connection to this port.
(Note) The DVI-D port does not support D-Sub connection by adapter.
•• When removing the cable connected to a back panel connector, first remove the cable from your device and then remove it from the motherboard.
•• When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent an electrical short inside the cable connector.
- 10 -
DisplayPort
DisplayPort delivers high quality digital imaging and audio, supporting bi-directional audio transmission. DisplayPort can support both DPCP and HDCP 2.3 content protection mechanisms. It provides improved visuals supporting Rec. 2020 (Wide Color Gamut) and High Dynamic Range (HDR) for Blu-ray UHD playback. You can use this port to connect your DisplayPort-supported monitor. Note: The DisplayPort Technology can support a maximum resolution of 4096x2304@60 Hz but the actual resolutions supported depend on the monitor being used.
HDMI Port
The HDMI port supports HDCP 2.3 and Dolby TrueHD and DTS HD Master Audio
formats. It also supports up to 192KHz/16bit 7.1-channel LPCM audio output. You can use this port to connect your HDMI-supported monitor. The maximum supported resolution is 4096x2160@30 Hz, but the actual resolutions supported are dependent on the monitor being used.
•• To set up a triple-display configuration, you must install motherboard drivers in the operating system first.
•• After installing the DisplayPort/HDMI device, make sure to set the default sound playback device to DisplayPort/HDMI. (The item name may differ depending on your operating system.)
Triple-Display Configurations for the Onboard Graphics:
Triple-display configurations are supported after you install motherboard drivers in OS. Only dual-display configurations are supported during the BIOS Setup or POST process.
USB 3.2 Gen 1 Port
The USB 3.2 Gen 1 port supports the USB 3.2 Gen 1 specification and is compatible to the USB 2.0 specification. Use this port for USB devices.
USB Type-C™ Port
The reversible USB port supports the USB 3.2 Gen 1 specification and is compatible to the USB 2.0 specification. Use this port for USB devices.
RJ-45 LAN Port
The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following describes the states of the LAN port LEDs.
Connection/ |
|
|
|
|
|
|
|
|
Connection/Speed LED: |
|
Activity LED: |
|
|||||||
Speed LED |
|
|
|
Activity LED |
|
|
|||||||||||||
|
|
|
|
|
|
|
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
State |
Description |
|
State |
Description |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Orange |
1 Gbps data rate |
|
Blinking |
Data transmission or receiving is occurring |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Green |
100 Mbps data rate |
|
On |
No data transmission or receiving is occurring |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Off |
10 Mbps data rate |
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
LAN Port |
|
|
|
||||||||||||
|
|
|
|
|
|
|
|
|
USB 3.2 Gen 1 Port (Q-Flash Plus Port)
The USB port supports the USB 3.2 Gen 1 specification. Use this port for USB devices. Before using Q-Flash Plus (Note), make sure to insert the USB flash drive into this port first.
Line In/Rear Speaker Out (Blue)
The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.
Line Out/Front Speaker Out (Green)
The line out jack. Use this audio jack for a headphone or 2-channel speaker.
Mic In/Center/Subwoofer Speaker Out (Pink)
The Mic in jack.
(Note) To enable the Q-Flash Plus function please visit the "Unique Features" webpage of GIGABYTE's website.
- 11 -
Audio Jack Configurations:
Jack |
Headphone/ |
4-channel |
5.1-channel |
7.1-channel |
|
2-channel |
|||||
|
|
|
|
||
Line In/Rear Speaker Out |
|
a |
a |
a |
|
|
|
|
|
|
|
Line Out/Front Speaker Out |
a |
a |
a |
a |
|
|
|
|
|
|
|
Mic In/Center/Subwoofer |
|
|
a |
a |
|
Speaker Out |
|
|
|||
|
|
|
|
||
Front Panel Line Out/Side |
|
|
|
a |
|
Speaker Out |
|
|
|
||
|
|
|
|
•• The integrated HD (High Definition) audio provides jack retasking capability that allows the user to change the function for each jack through the audio driver.
•• To configure 7.1-channel audio, you need to open the audio software and select Device advanced settings > Playback Device to change the default setting first.
Please visit GIGABYTE's website for details on configuring the audio software.
- 12 -
4 |
1 |
3 |
|
|
4 |
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2 |
|
|
|
|
|
|
|
|
|
|
8 |
9 |
|
|
|
|
|
|
|
|
|
12 |
|
|
|
|
|
|
|
|
|
|
|
19 |
|
|
|
|
|
|
|
|
|
17 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
8 |
|
|
|
|
|
|
|
|
|
|
18 |
11 |
14 |
15 |
7 |
5 |
6 |
13 |
9 |
16 |
4 |
10 |
1) |
ATX_12V_2X4 |
11) |
F_AUDIO |
2) |
ATX |
12) |
F_U32 |
3) |
CPU_FAN |
13) |
F_USB1/F_USB2 |
4) |
SYS_FAN1/2/3 |
14) |
COM |
5) |
D_LED1 |
15) |
LPT |
6) |
LED_C1 |
16) |
SPI_TPM |
7) |
QFLASH_PLUS |
17) |
THB_C1/THB_C2 |
8) |
SATA3 0/1/2/3/4/5 |
18) |
CLR_CMOS |
9) |
M2Q/M2P |
19) |
BAT |
10) |
F_PANEL |
|
|
Read the following guidelines before connecting external devices:
•• First make sure your devices are compliant with the connectors you wish to connect.
•• Before installing the devices, be sure to turn off the devices and your computer. Unplug the power cord from the power outlet to prevent damage to the devices.
•• After installing the device and before turning on the computer, make sure the device cable has been securely attached to the connector on the motherboard.
- 13 -
1/2) ATX_12V_2X4/ATX (2x4 12V Power Connector and 2x12 Main Power Connector)
With the use of the power connector, the power supply can supply enough stable power to all the components on the motherboard. Before connecting the power connector, first make sure the power supply is turned off and all devices are properly installed. The power connector possesses a foolproof design. Connect the power supply cable to the power connector in the correct orientation.
The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected, the computer will not start.
To meet expansion requirements, it is recommended that a power supply that can withstand high power consumption be used (500W or greater). If a power supply is used that does not provide the required power, the result can lead to an unstable or unbootable system.
|
|
ATX_12V_2X4: |
|
|
||
|
|
Pin No. |
Definition |
Pin No. |
Definition |
|
5 |
8 |
1 |
GND (Only for 2x4-pin 12V) |
5 |
+12V (Only for 2x4-pin 12V) |
|
1 |
4 |
2 |
GND (Only for 2x4-pin 12V) |
6 |
+12V (Only for 2x4-pin 12V) |
|
|
ATX_12V_2X4 |
3 |
GND |
7 |
+12V |
|
|
4 |
GND |
8 |
+12V |
||
|
|
|||||
|
|
ATX: |
|
|
|
|
12 |
24 |
Pin No. |
Definition |
Pin No. |
Definition |
|
1 |
3.3V |
13 |
3.3V |
|||
|
|
|||||
|
|
2 |
3.3V |
14 |
-12V |
|
|
|
3 |
GND |
15 |
GND |
|
|
|
4 |
+5V |
16 |
PS_ON (soft On/Off) |
|
|
|
5 |
GND |
17 |
GND |
|
|
|
6 |
+5V |
18 |
GND |
|
|
|
7 |
GND |
19 |
GND |
|
|
|
8 |
Power Good |
20 |
NC |
|
|
|
9 |
5VSB (stand by +5V) |
21 |
+5V |
|
|
|
10 |
+12V |
22 |
+5V |
|
|
|
11 |
+12V (Only for 2x12-pin |
23 |
+5V (Only for 2x12-pin ATX) |
|
1 |
13 |
|
ATX) |
|
|
|
12 |
3.3V (Only for 2x12-pin ATX) |
24 |
GND (Only for 2x12-pin ATX) |
|||
|
|
ATX
3/4) CPU_FAN/SYS_FAN1/2/3 (Fan Headers)
All fan headers on this motherboard are 4-pin. Most fan headers possess a foolproof insertion design. When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is the ground wire). The speed control function requires the use of a fan with fan speed control design. For optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.
|
|
|
|
|
|
|
|
|
|
|
|
|
Pin No. |
Definition |
|
|
|
|
1 |
|
|
|
1 |
|
|
|
|
1 |
GND |
|
|
|
|
|
|
1 |
|
|
|
|
2 |
Voltage Speed Control |
||
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|||||||||
CPU_FAN/SYS_FAN1 |
SYS_FAN2 |
|
SYS_FAN3 |
3 |
Sense |
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
4 |
PWM Speed Control |
•• Be sure to connect fan cables to the fan headers to prevent your CPU and system from overheating. Overheating may result in damage to the CPU or the system may hang.
•• Thesefanheadersarenotconfigurationjumperblocks.Donotplaceajumpercapontheheaders.
- 14 -
5)D_LED1 (Addressable LED Strip Header)
The header can be used to connect a standard 5050 addressable LED strip, with maximum power rating of 5A (5V) and maximum number of 1000 LEDs.
1
Addressable LED
Strip
1
Pin No. |
Definition |
1 |
V (5V) |
2 |
D |
3 |
No Pin |
4 |
G |
Connect your addressable LED strip to the header. The power pin (marked with a triangle on the plug) of the LED strip must be connected to Pin 1 of the addressable LED strip header. Incorrect connection may lead to the damage of the LED strip.
6)LED_C1 (RGB LED Strip Header)
The header can be used to connect a standard 5050 RGB LED strip (12V/G/R/B), with maximum power rating of 2A (12V) and maximum length of 2m.
1
LED_C1 |
RGB LED Strip |
|
1
12V
Pin No. |
Definition |
1 |
12V |
2 |
G |
3 |
R |
4 |
B |
Connect your RGB LED strip to the header. The power pin (marked with a triangle on the plug) of the LED strip must be connected to Pin 1 (12V) of this header. Incorrect connection may lead to the damage of the LED strip.
For how to turn on/off the lights of the LED strip please visit the "Unique Features" webpage of GIGABYTE's website.
Before installing the devices, be sure to turn off the devices and your computer. Unplug the power cord from the power outlet to prevent damage to the devices.
- 15 -