GA-Z87-DS3H GA-H87-DS3H
User's Manual
Rev. 1101
12ME-Z87DS3H-1101R
Motherboard
GA-Z87-DS3H/GA-H87-DS3H
Motherboard
GA-Z87-DS3H
GA-H87-DS3H
Sept. 25, 2013
Sept. 25, 2013
Copyright
© 2013 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.
Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice.
No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission.
Documentation Classifications
In order to assist in the use of this product, GIGABYTE provides the following types of documentations:
For quick set-up of the product, read the Quick Installation Guide included with the product.For detailed product information, carefully read the User's Manual.
For product-related information, check on our website at: http://www.gigabyte.com
Identifying Your Motherboard Revision
The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0" means the revision of the motherboard is 1.0. Check your motherboard revision before updating motherboard BIOS, drivers, or when looking for technical information.
Example:
Table of Contents
Box Contents.................................................................................................................... |
|
|
6 |
Optional Items.................................................................................................................. |
|
6 |
|
GA-Z87-DS3H/GA-H87-DS3H Motherboard Layout....................................................... |
7 |
||
GA-Z87-DS3H/GA-H87-DS3H Motherboard Block Diagram.......................................... |
8 |
||
Chapter 1 Hardware Installation...................................................................................... |
9 |
||
1-1 |
Installation Precautions.................................................................................... |
9 |
|
1-2 |
Product Specifications................................................................................... |
10 |
|
1-3 |
Installing the CPU and CPU Cooler............................................................... |
13 |
|
|
1-3-1 |
Installing the CPU................................................................................................... |
13 |
|
1-3-2 Installing the CPU Cooler....................................................................................... |
15 |
|
1-4 |
Installing the Memory..................................................................................... |
16 |
|
|
1-4-1 Dual Channel Memory Configuration..................................................................... |
16 |
|
|
1-4-2 |
Installing a Memory................................................................................................ |
17 |
1-5 |
Installing an Expansion Card......................................................................... |
18 |
|
1-6 |
Back Panel Connectors.................................................................................. |
19 |
|
1-7 |
Internal Connectors........................................................................................ |
21 |
|
Chapter 2 BIOS Setup................................................................................................... |
31 |
||
2-1 |
Startup Screen............................................................................................... |
32 |
|
2-2 |
The Main Menu.............................................................................................. |
33 |
|
2-3 |
M.I.T................................................................................................................ |
35 |
|
2-4 |
System Information........................................................................................ |
46 |
|
2-5 |
BIOS Features................................................................................................ |
47 |
|
2-6 |
Peripherals..................................................................................................... |
51 |
|
2-7 |
Power Management....................................................................................... |
55 |
|
2-8 |
Save & Exit..................................................................................................... |
57 |
|
Chapter 3 Configuring SATA Hard Drive(s)................................................................... |
59 |
||
3-1 |
Configuring SATA Controllers........................................................................ |
59 |
|
3-2 |
Installing the SATA RAID/AHCI Driver and Operating System...................... |
71 |
- 4 -
Chapter 4 Drivers Installation........................................................................................ |
75 |
|
4-1 |
Chipset Drivers............................................................................................... |
75 |
4-2 |
Application Software...................................................................................... |
76 |
4-3 |
Information..................................................................................................... |
76 |
Chapter 5 Unique Features........................................................................................... |
77 |
||
5-1 |
BIOS Update Utilities...................................................................................... |
77 |
|
5 |
-1-1 |
Updating the BIOS with the Q-Flash Utility........................................................... |
77 |
5 |
-1-2 |
Updating the BIOS with the @BIOS Utility........................................................... |
80 |
5-2 |
APP Center..................................................................................................... |
81 |
|
5 |
-2-1 |
EasyTune................................................................................................................ |
82 |
5 |
-2-2 |
EZ Setup................................................................................................................ |
83 |
5 |
-2-3 |
USB Blocker.......................................................................................................... |
88 |
Chapter 6 Appendix |
....................................................................................................... |
89 |
|
6-1 Configuring Audio Input and Output............................................................... |
89 |
||
6 |
-1-1 |
Configuring 2/4/5.1/7.1 - Channel Audio ................................................................. |
89 |
6 |
-1-2 |
Configuring S/PDIF In/Out ..................................................................................... |
91 |
6 |
-1-3 ....................................................................... |
Configuring Microphone Recording |
92 |
6 |
-1-4 .................................................................................... |
Using the Sound Recorder |
95 |
6-2 |
Troubleshooting.............................................................................................. |
96 |
|
6 |
-2-1 ................................................................................ |
Frequently Asked Questions |
96 |
6 |
-2-2 .................................................................................... |
Troubleshooting Procedure |
97 |
Regulatory ..............................................................................................Statements |
99 |
||
Contact Us............................................................................................................... |
103 |
- 5 -
55 GA-Z87-DS3H or GA-H87-DS3H motherboard 55 Motherboard driver disk
55 User's Manual
55 Quick Installation Guide
55 Two SATA cables
55 I/O Shield
The box contents above are for reference only and the actual items shall depend on the product package you obtain. The box contents are subject to change without notice.
2-port USB 2.0 bracket (Part No. 12CR1-1UB030-6*R)eSATA bracket (Part No. 12CF1-3SATPW-4*R)
3.5" Front Panel with 2 USB 3.0/2.0 ports (Part No. 12CR1-FPX582-2*R)S/PDIF In cable (Part No. 12CR1-1SPDIN-1*R)
HDMI-to-DVI adapter (Part No. 12CT2-HDMI01-1*R)LPT port cable (Part No. 12CF1-1LP001-0*R)
COM port cable (Part No. 12CF1-1CM001-3*R)
- 6 -
KB_MS_USB
CPU_FAN
ATX_12V_2X4
DVI
VGA
LGA1150
ATX
HDMI
R_USB30
USB30_LAN GA-Z87-DS3H/GA-H87-DS3H
AUDIO |
SYS_FAN1 SYS_FAN2 |
|
PCIEX1_1
PCIEX16
Realtek®
GbE LAN
|
|
BAT |
CODEC |
PCIEX1_2 |
|
|
PCIEX1_3 |
PCIe to |
|
|
|
|
|
PCI Bridge |
iTE® Super I/O |
PCI1 |
|
PCI2 |
|
|
SPDIF_IN |
|
|
F_AUDIO |
COMA |
|
SPDIF_O |
LPT |
SYS_FAN3
F_USB30
DDR3_1
DDR3_3
DDR3_2
DDR3_4
Intel® Z87j
Intel® H87k
SATA3
1 |
0 |
3 |
2 |
5 |
4 |
M_BIOS
B_BIOS
CLR_CMOS
F_PANEL F_USB2
F_USB3 |
F_USB1 |
j Only for GA-Z87-DS3H. k Only for GA-H87-DS3H.
- 7 -
1 PCI Express x16
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CPU CLK+/- (100 MHz) |
|
|
|
||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||
|
|
PCIe CLK |
|
|
|
|
|
|
|
|
|
|
DVI-D |
|
|
|
|
|
LGA1150 |
|
|
|
|
|
|
|
|
|
DDR3 1600/1333 MHz |
|
|
|||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
HDMI |
|
|
|
|
|
|
CPU |
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||||||
|
|
(100 MHz) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Dual Channel Memory |
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DMI 2.0 |
|
|
FDI |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
PCI Express Bus |
|
|
x16 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
LAN |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
D-Sub |
|
|
|
|||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
RJ45 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Dual BIOS |
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Realtek® |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
GbE LAN |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
6 SATA 6Gb/s |
|
|
||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||
|
|
PCI Express Bus |
|
|
|
|
|
|
|
|
|
|
x1 |
|
|
|
|
Intel® Z87j |
|
|
|
|
|
|
|
|
6 USB 3.0/2.0 |
|
|
|||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||||||||||||||||
|
|
|
|
x1 |
|
x1 |
|
|
x1 |
|
|
|
|
x1 |
|
|
|
|
Intel® H87k |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PCIe to PCI |
8 USB 2.0/1.1 |
|
|
Bridge |
||
3 PCI Express x1 |
PCI Bus |
|
LPT |
|
LPC Bus |
iTE® |
|
|
|
|
|
|
|
Super |
COM |
|
|
I/O |
|
|
CODEC |
|
PS/2 KB/Mouse |
|
|
|
|
|
|
|
|
|
|
|
Speaker Out |
|
In |
In |
|
|
|
|
|
|
|
SpeakerOut |
SpeakerOut |
Out |
Out |
|
|
|
|
|
|
|
|
Line |
S/PDIF |
|||
|
|
|
|
|
|
|
MIC Line |
||||
|
|
|
|
|
|
|
|||||
|
2 PCI |
|
S/PDIF |
||||||||
|
|
|
|
|
|
|
Rear |
Center/Subwoofer |
Side |
|
|
|
|
|
|
|
|
|
|
|
|||
PCI CLK |
|
|
|
|
|
|
|
|
(33 MHz)
j Only for GA-Z87-DS3H. k Only for GA-H87-DS3H.
For detailed product information/limitation(s), refer to "1-2 Product Specifications."
- 8 -
The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's manual and follow these procedures:
•• Prior to installation, make sure the chassis is suitable for the motherboard.
•• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or warranty sticker provided by your dealer. These stickers are required for warranty validation.
•• Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components.
•• When connecting hardware components to the internal connectors on the motherboard, make sure they are connected tightly and securely.
•• When handling the motherboard, avoid touching any metal leads or connectors.
•• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap, keep your hands dry and first touch a metal object to eliminate static electricity.
•• Prior to installing the motherboard, please have it on top of an antistatic pad or within an electrostatic shielding container.
•• Before unplugging the power supply cable from the motherboard, make sure the power supply has been turned off.
•• Before turning on the power, make sure the power supply voltage has been set according to the local voltage standard.
•• Before using the product, please verify that all cables and power connectors of your hardware components are connected.
•• To prevent damage to the motherboard, do not allow screws to come in contact with the motherboard circuit or its components.
•• Make sure there are no leftover screws or metal components placed on the motherboard or within the computer casing.
•• Do not place the computer system on an uneven surface.
•• Do not place the computer system in a high-temperature environment.
•• Turning on the computer power during the installation process can lead to damage to system components as well as physical harm to the user.
•• If you are uncertain about any installation steps or have a problem related to the use of the product, please consult a certified computer technician.
- 9 - |
Hardware Installation |
1-2 |
Product Specifications |
|
||||
|
|
|
||||
|
CPU |
Support for Intel® Core™ i7 processors/Intel® Core™ i5 processors/ |
||||
|
|
Intel® Core™ i3 processors/Intel® Pentium® processors/ |
||||
|
|
Intel® Celeron® processors in the LGA1150 package (Go to |
||||
|
|
GIGABYTE's website for the latest CPU support list.) |
||||
|
|
L3 cache varies with CPU |
||||
|
Chipset |
Intel |
® |
Z87 /H87 |
|
Express Chipset |
|
|
|
j |
k |
|
|
|
Memory |
4 x 1.5V DDR3 DIMM sockets supporting up to 32 GB of system memory |
||||
|
|
|
* |
Due to a Windows 32-bit operating system limitation, when more than 4 GB of |
||
|
|
|
|
physical memory is installed, the actual memory size displayed will be less than the |
||
|
|
|
|
size of the physical memory installed. |
Dual channel memory architecture
Support for DDR3 1600/1333 MHz memory modules
Support for non-ECC memory modules
Support for Extreme Memory Profile (XMP) memory modules
(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)
Onboard |
|
Integrated Graphics Processor: |
|
Graphics |
|
- |
1 x D-Sub port |
|
|
- |
1 x DVI-D port, supporting a maximum resolution of 1920x1200 |
|
|
|
* The DVI-D port does not support D-Sub connection by adapter. |
|
|
- |
1 x HDMI port, supporting a maximum resolution of 4096x2160 |
|
|
|
* Support for HDMI 1.4a version. |
|
|
- |
Maximum shared memory of 1 GB |
Audio |
|
Realtek® ALC887 codec |
|
|
|
High Definition Audio |
|
|
|
2/4/5.1/7.1-channel |
|
|
|
Support for S/PDIF In |
|
|
|
Support for S/PDIF Out |
|
LAN |
|
Realtek® GbE LAN chip (10/100/1000 Mbit) |
|
Expansion Slots |
|
1 x PCI Express x16 slot, running at x16 (PCIEX16) |
|
|
|
(The PCIEX16 slot conforms to PCI Express 3.0 standard.) |
|
|
|
3 x PCI Express x1 slots |
|
|
|
(All PCI Express x1 slots conform to PCI Express 2.0 standard.) |
|
|
|
2 x PCI slots |
|
Storage Interface |
|
Chipset: |
|
|
|
- |
6 x SATA 6Gb/s connectors |
|
|
- |
Support for RAID 0, RAID 1, RAID 5, and RAID 10 |
j Only for GA-Z87-DS3H. k Only for GA-H87-DS3H.
Hardware Installation |
- 10 - |
USB |
|
Chipset: |
|
|
|
- |
6 x USB 3.0/2.0 ports (4 ports on the back panel, 2 ports available through |
|
|
|
the internal USB header) |
|
|
- |
8 x USB 2.0/1.1 ports (2 ports on the back panel, 6 ports available through |
|
|
|
the internal USB headers) |
Internal |
1 x 24-pin ATX main power connector |
||
Connectors |
1 x 8-pin ATX 12V power connector |
||
|
6 x SATA 6Gb/s connectors |
||
|
1 x CPU fan header |
||
|
3 x system fan headers |
||
|
1 x front panel header |
||
|
1 x front panel audio header |
||
|
1 x S/PDIF Out header |
||
|
1 x S/PDIF In header |
||
|
1 x USB 3.0/2.0 header |
||
|
3 x USB 2.0/1.1 headers |
||
|
1 x serial port header |
||
|
1 x parallel port header |
||
|
1 x Clear CMOS jumper |
||
Back Panel |
1 x PS/2 keyboard/mouse port |
||
Connectors |
1 x D-Sub port |
||
|
1 x DVI-D port |
||
|
1 x HDMI port |
||
|
4 x USB 3.0/2.0 ports |
||
|
2 x USB 2.0/1.1 ports |
||
|
1 x RJ-45 port |
||
|
6 x audio jacks (Center/Subwoofer Speaker Out, Rear Speaker Out, Side |
||
|
|
Speaker Out, Line In, Line Out, Mic In) |
|
I/O Controller |
iTE® I/O Controller Chip |
||
|
|
|
|
Hardware |
|
System voltage detection |
|
Monitor |
|
CPU/System temperature detection |
|
|
CPU/System fan speed detection |
||
|
CPU overheating warning |
||
|
CPU/System fan fail warning |
||
|
CPU/System fan speed control |
*Whether the fan speed control function is supported will depend on the cooler you install.
- 11 - |
Hardware Installation |
BIOS |
2 x 64 Mbit flash |
|
Use of licensed AMI EFI BIOS |
|
Support for DualBIOS™ |
|
PnP 1.0a, DMI 2.0, SM BIOS 2.6, ACPI 2.0a |
Unique Features |
Support for Q-Flash |
|
Support for Xpress Install |
|
Support for APP Center |
|
|
* Available applications in APP Center may differ by motherboard model. Supported |
|
|
functions of each application may also differ depending on motherboard |
|
|
specifications. |
|
- |
@BIOS |
|
- |
EasyTune |
|
- |
EZ Setup |
|
- |
USB Blocker |
|
- |
Smart TimeLock |
|
- |
Smart Recovery 2 |
|
Support for ON/OFF Charge |
|
Bundled |
Norton® Internet Security (OEM version) |
|
Software |
Intel® Rapid Start Technology |
|
|
Intel® Smart Connect Technology |
|
|
Intel® Smart Response Technology |
|
|
Intel® Small Business Advantage k |
|
Operating |
Support for Windows 8.1/8/7 |
|
System |
|
* If you plan to install Windows 8.1, please download the latest drivers from |
|
|
GIGABYTE's website. |
Form Factor |
ATX Form Factor; 30.5cm x 19.0cm |
*GIGABYTE reserves the right to make any changes to the product specifications and product-related information without prior notice.
*Please visit the Support & Downloads\Utility page on GIGABYTE's website to check the supported operating system(s) for the software listed in the "Unique Features" and "Bundled Software" columns.
k Only for GA-H87-DS3H.
Hardware Installation |
- 12 - |
1-3 |
Installing the CPU and CPU Cooler |
|
|
Read the following guidelines before you begin to install the CPU: |
|
|
•• |
Make sure that the motherboard supports the CPU. |
|
|
(Go to GIGABYTE's website for the latest CPU support list.) |
|
•• |
Always turn off the computer and unplug the power cord from the power outlet before installing the |
|
|
CPU to prevent hardware damage. |
|
•• |
Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may |
|
|
locate the notches on both sides of the CPU and alignment keys on the CPU socket.) |
|
•• |
Apply an even and thin layer of thermal grease on the surface of the CPU. |
|
•• |
Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage |
|
|
of the CPU may occur. |
|
•• |
Set the CPU host frequency in accordance with the CPU specifications. It is not recommended |
|
|
that the system bus frequency be set beyond hardware specifications since it does not meet the |
|
|
standard requirements for the peripherals. If you wish to set the frequency beyond the standard |
|
|
specifications, please do so according to your hardware specifications including the CPU, graphics |
|
|
card, memory, hard drive, etc. |
A. Locate the alignment keys on the motherboard CPU socket and the notches on the CPU.
|
LGA1150 CPU Socket |
Alignment |
Alignment |
Key |
Key |
Pin One Corner of the CPU Socket
LGA1150 CPU
NotchNotch
Triangle Pin One Marking on the CPU
- 13 - |
Hardware Installation |
B. Follow the steps below to correctly install the CPU into the motherboard CPU socket.
•• Before installing the CPU, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the CPU.
•• To protect the socket contacts, do not remove the protective plastic cover unless the CPU is inserted into the CPU socket. Save the cover properly and replace it if the CPU is removed.
Step 1:
Gently press the CPU socket lever handle down and away from the socket with your finger. Then completely lift the CPU socket lever and the metal load plate/plastic cover will be lifted as well.
Step 3:
Once the CPU is properly inserted, carefully replace the load plate. When replacing the load plate, make sure the front end of the load plate is under the shoulder screw. Then press the CPU socket lever. The protective plastic cover may pop off from the load plate during the process of engaging the lever. Remove the cover. (Save the cover properly and always replace it when the
CPU is not installed.)
Step 2:
Hold the CPU with your thumb and index fingers. Align the CPU pin one marking (triangle) with the pinonecorneroftheCPUsocket(oryoumayalign the CPU notches with the socket alignment keys) and gently insert the CPU into position.
Step 4:
Finally, secure the lever under its retention tab to complete the installation of the CPU.
NOTE:
Hold the CPU socket lever by the handle, not the lever base portion.
Hardware Installation |
- 14 - |
Follow the steps below to correctly install the CPU cooler on the motherboard. (The following procedure uses Intel® boxed cooler as the example cooler.)
Step 1:
Apply an even and thin layer of thermal grease on the surface of the installed CPU.
Step 3:
Place the cooler atop the CPU, aligning the four push pins through the pin holes on the motherboard. Push down on the push pins diagonally.
|
|
|
|
|
|
Male |
|
|
|
|
|
|
|
Direction of |
|
|
Push Pin |
|||
|
|
|
||||
the Arrow Sign |
|
|
|
The Top |
||
on the Male |
|
|
||||
|
|
of Female |
||||
Push Pin |
|
|
||||
|
|
Push Pin |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
Female |
|
|
|
|
|
|
Push Pin |
Step 2:
Before installing the cooler, note the direction of the arrow sign onthemalepushpin.(Turningthe push pin along the direction of arrow is to remove the cooler, on the contrary, is to install.)
Step 4:
You should hear a "click" when pushing down each push pin. Check that the Male and Female push pins are joined closely.
(Refer to your CPU cooler installation manual for instructions on installing the cooler.)
Step 5:
After the installation, check the back of the motherboard. If the push pin is inserted as the picture above shows, the installation is complete.
Step 6:
Finally, attach the power connector of the CPU cooler to the CPU fan header (CPU_FAN) on the motherboard.
Use extreme care when removing the CPU cooler because the thermal grease/tape between the CPU cooler and CPU may adhere to the CPU. Inadequately removing the CPU cooler may damage the CPU.
- 15 - |
Hardware Installation |
Read the following guidelines before you begin to install the memory:
•• Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips be used.
(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)
•• Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage.
•• Memory modules have a foolproof design. A memory module can be installed in only one direction. If you are unable to insert the memory, switch the direction.
This motherboard provides four DDR3 memory sockets and supports Dual Channel Technology. After the memory is installed, the BIOS will automatically detect the specifications and capacity of the memory. Enabling
Dual Channel memory mode will double the original memory bandwidth.
The four DDR3 memory sockets are divided into two channels and each channel has two memory sockets as following:
Channel A: DDR3_4, DDR3_2
Channel B: DDR3_3, DDR3_1
Dual Channel Memory Configurations Table:
|
DDR3_4 |
DDR3_2 |
DDR3_3 |
DDR3_1 |
|
|
|
|
|
Two Modules |
- - |
DS/SS |
- - |
DS/SS |
|
DS/SS |
- - |
DS/SS |
- - |
Four Modules |
DS/SS |
DS/SS |
DS/SS |
DS/SS |
(SS=Single-Sided, DS=Double-Sided, "- -"=No Memory)
DDR3_1
DDR3_3
DDR3_2
DDR3_4
Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode.
1.Dual Channel mode cannot be enabled if only one DDR3 memory module is installed.
2.WhenenablingDualChannelmode withtwoor fourmemorymodules,it isrecommendedthatmemory of the same capacity, brand, speed, and chips be used and installed in the same colored DDR3 sockets. For optimum performance, when enabling Dual Channel mode with two memory modules, we recommend that you install them in the DDR3_1 and DDR3_2 sockets.
Hardware Installation |
- 16 - |
Before installing a memory module, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the memory module. DDR3 and DDR2 DIMMs are not compatible to each other or DDR DIMMs. Be sure to install DDR3 DIMMs on this motherboard.
Notch
DDR3 DIMM
ADDR3 memory module has a notch, so it can only fit in one direction. Follow the steps below to correctly install your memory modules in the memory sockets.
Step 1:
Note the orientation of the memory module. Spread the retaining clips at both ends of the memory socket. Place the memory module on the socket. As indicated in the picture on the left, place your fingers on the top edge of the memory, push down on the memory and insert it vertically into the memory socket.
Step 2:
The clips at both ends of the socket will snap into place when the memory module is securely inserted.
- 17 - |
Hardware Installation |
Read the following guidelines before you begin to install an expansion card:
•• Make sure the motherboard supports the expansion card. Carefully read the manual that came with your expansion card.
•• Always turn off the computer and unplug the power cord from the power outlet before installing an expansion card to prevent hardware damage.
PCI Express x1 Slot
PCI Express x16 Slot
PCI Slot
Follow the steps below to correctly install your expansion card in the expansion slot.
1.Locate an expansion slot that supports your card. Remove the metal slot cover from the chassis back panel.
2.Align the card with the slot, and press down on the card until it is fully seated in the slot.
3.Make sure the metal contacts on the card are completely inserted into the slot.
4.Secure the card’s metal bracket to the chassis back panel with a screw.
5.After installing all expansion cards, replace the chassis cover(s).
6.Turn on your computer. If necessary, go to BIOS Setup to make any required BIOS changes for your expansion card(s).
7.Install the driver provided with the expansion card in your operating system.
Example: Installing and Removing a PCI Express Graphics Card:
•• Installing a Graphics Card:
Gently push down on the top edge of the card until it is fully inserted into the PCI Express slot. Make sure the card is securely seated in the slot and does not rock.
•• Removing the Card:
Gently push back on the lever on the slot and then lift the card straight out from the slot.
Hardware Installation |
- 18 - |
USB 2.0/1.1 Port
The USB port supports the USB 2.0/1.1 specification. Use this port for USB devices such as a USB keyboard/mouse, USB printer, USB flash drive and etc.
PS/2 Keyboard/Mouse Port
Use this port to connect a PS/2 mouse or keyboard.
D-Sub Port
The D-Sub port supports a 15-pin D-Sub connector and supports a maximum resolution of 1920x1200. Connect a monitor that supports D-Sub connection to this port.
DVI-D Port (Note)
The DVI-D port conforms to the DVI-D specification and supports a maximum resolution of 1920x1200 (the actual resolutions supported depend on the monitor being used). Connect a monitor that supports
DVI-D connection to this port.
HDMI Port
The HDMI port is HDCP compliant and supports Dolby True HD and DTS HD
MasterAudioformats.Italsosupportsupto192KHz/24bit8-channelLPCMaudio output. You can use this port to connect your HDMI-supported monitor. The maximum supported resolution is 4096x2160, but the actual resolutions supported are dependent on the monitor being used.
After installing the HDMI device, make sure to set the default sound playback device to HDMI.
(The item name may differ depending on your operating system. The screenshot below is from Windows 8.)
In Windows 8, selectAllApps>Control Panel>Hardwareand Sound>Sound>Playback, set Intel(R) Display Audio to the default playback device.
(Note) The DVI-D port does not support D-Sub connection by adapter.
•• When removing the cable connected to a back panel connector, first remove the cable from your device and then remove it from the motherboard.
•• Whenremovingthecable,pullitstraightoutfromtheconnector.Donotrockitsidetosidetoprevent an electrical short inside the cable connector.
- 19 - |
Hardware Installation |
Triple-Display Configurations for the Onboard Graphics:
Triple-display configurations are supported after you install motherboard drivers in OS. Only dual-display configurations are supported during the BIOS Setup or POST process.
USB 3.0/2.0 Port
The USB 3.0 port supports the USB 3.0 specification and is compatible to the USB 2.0/1.1 specification. Use this port for USB devices such as a USB keyboard/mouse, USB printer, USB flash drive and etc.
RJ-45 LAN Port
The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following describes the states of the LAN port LEDs.
Connection/ |
|
|
|
|
|
|
|
|
Connection/Speed LED: |
|
Activity LED: |
|
|||||||
Speed LED |
|
|
|
Activity LED |
|
|
|||||||||||||
|
|
|
|
|
|
|
|
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
State |
Description |
|
State |
Description |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Orange |
1 Gbps data rate |
|
Blinking |
Data transmission or receiving is occurring |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Green |
100 Mbps data rate |
|
Off |
No data transmission or receiving is occurring |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Off |
10 Mbps data rate |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
LAN Port |
|
|
|
||||||||||||
|
|
|
|
|
|
|
|
|
Center/Subwoofer Speaker Out Jack (Orange)
Use this audio jack to connect center/subwoofer speakers in a 5.1/7.1-channel audio configuration.
Rear Speaker Out Jack (Black)
This jack can be used to connect front speakers in a 4/5.1/7.1-channel audio configuration.
Side Speaker Out Jack (Gray)
Use this audio jack to connect side speakers in a 7.1-channel audio configuration.
Line In Jack (Blue)
The default line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.
Line Out Jack (Green)
The default line out jack. Use this audio jack for a headphone or 2-channel speaker. This jack can be used to connect front speakers in a 4/5.1/7.1-channel audio configuration.
Mic In Jack (Pink)
The default Mic in jack. Microphones must be connected to this jack.
Theaudiojackscanbereconfigured toperformdifferent functionsviatheaudiosoftware(supported functions foreach jack may varybased onhardware specification). Only microphones stillMUSTbe connected to the default Mic in jack. Refer to the instructions on setting up a 2/4/5.1/7.1-channel
audio configuration in Chapter 6, "Configuring 2/4/5.1/7.1-Channel Audio."
Hardware Installation |
- 20 - |
1 |
3 |
||
|
|
|
|
|
|
|
|
|
2 |
4 |
12 |
|
4 |
5 |
|
|
6 |
10 |
7 |
9 11 |
14 |
15 |
13 |
8 |
13 |
1) |
ATX_12V_2X4 |
9) |
F_AUDIO |
2) |
ATX |
10) |
SPDIF_IN |
3) |
CPU_FAN |
11) |
SPDIF_O |
4) |
SYS_FAN1/2/3 |
12) |
F_USB30 |
5) |
BAT |
13) |
F_USB1/F_USB2/F_USB3 |
6) |
SATA3 0/1/2/3/4/5 |
14) |
COMA |
7) |
CLR_CMOS |
15) |
LPT |
8) |
F_PANEL |
|
|
Read the following guidelines before connecting external devices:
•• First make sure your devices are compliant with the connectors you wish to connect.
•• Before installing the devices, be sure to turn off the devices and your computer. Unplug the power cord from the power outlet to prevent damage to the devices.
•• After installing the device and before turning on the computer, make sure the device cable has been securely attached to the connector on the motherboard.
- 21 - |
Hardware Installation |
1/2) ATX_12V_2X4/ATX (2x4 12V Power Connector and 2x12 Main Power Connector)
Withtheuseofthepowerconnector,thepowersupplycansupplyenoughstablepowertoallthecomponents on the motherboard. Before connecting the power connector, first make sure the power supply is turned off and all devices are properly installed. The power connector possesses a foolproof design. Connect the power supply cable to the power connector in the correct orientation.
The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected, the computer will not start.
To meet expansion requirements, it is recommended that a power supply that can withstand high power consumption be used (500W or greater). If a power supply is used that does not provide the required power, the result can lead to an unstable or unbootable system.
12 24
1 |
13 |
ATX
|
|
|
ATX_12V_2X4: |
|
|
|
|
Pin No. |
Definition |
|
|
|
1 |
GND (Only for 2x4-pin 12V) |
|
|
|
2 |
GND (Only for 2x4-pin 12V) |
|
5 |
8 |
3 |
GND |
|
4 |
GND |
||
|
1 |
4 |
||
|
5 |
+12V (Only for 2x4-pin 12V) |
||
|
|
|
||
|
ATX_12V_2X4 |
|
6 |
+12V (Only for 2x4-pin 12V) |
|
|
|
7 |
+12V |
|
|
|
8 |
+12V |
ATX: |
|
|
|
|
Pin No. |
Definition |
|
Pin No. |
Definition |
1 |
3.3V |
|
13 |
3.3V |
2 |
3.3V |
|
14 |
-12V |
3 |
GND |
|
15 |
GND |
4 |
+5V |
|
16 |
PS_ON (soft On/Off) |
5 |
GND |
|
17 |
GND |
6 |
+5V |
|
18 |
GND |
7 |
GND |
|
19 |
GND |
8 |
Power Good |
|
20 |
-5V |
9 |
5VSB (stand by +5V) |
21 |
+5V |
|
10 |
+12V |
|
22 |
+5V |
11 |
+12V (Only for 2x12-pin |
23 |
+5V (Only for 2x12-pin ATX) |
|
|
ATX) |
|
|
|
12 |
3.3V (Only for 2x12-pin |
24 |
GND (Only for 2x12-pin |
|
|
ATX) |
|
|
ATX) |
Hardware Installation |
- 22 - |
3/4) CPU_FAN/SYS_FAN1/SYS_FAN2/SYS_FAN3 (Fan Headers)
Themotherboardhasa4-pinCPUfanheader(CPU_FAN),two4-pin(SYS_FAN1/2)anda3-pin(SYS_FAN) system fan headers. Most fan headers possess a foolproof insertion design. When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is the ground wire). The speed control function requires the use of a fan with fan speed control design. For optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.
|
|
|
|
|
|
CPU_FAN: |
|
|
|
|
|
|
|
1 |
Pin No. |
|
Definition |
|
|
|
|
1 |
|
GND |
||
|
|
|
|
|
|
|
||
|
CPU_FAN |
|
||||||
|
2 |
|
+12V |
|||||
|
|
|
|
|
|
3 |
|
Sense |
|
|
|
|
|
|
4 |
|
Speed Control |
|
|
|
|
|
|
SYS_FAN1/2: |
||
1 |
|
|
|
|
Pin No. |
|
Definition |
|
|
|
|
|
|
||||
|
|
|
|
|
|
1 |
|
GND |
|
|
|
|
|
|
|
||
|
|
|
|
|
|
2 |
|
+12V / Speed Control |
SYS_FAN1/2 |
|
|||||||
3 |
|
Sense |
||||||
|
|
|
|
|
|
|
||
|
|
|
|
|
|
4 |
|
VCC |
|
|
|
|
|
|
SYS_FAN3 |
|
|
|
|
|
|
|
|
Pin No. |
Definition |
|
|
|
|
|
|
|
|||
|
|
|
|
1 |
1 |
|
GND |
|
|
|
|
|
|
||||
2 |
|
+12V |
||||||
SYS_FAN3 |
|
|||||||
3 |
|
N/A |
||||||
|
|
|
|
|
|
|
•• Be sure to connect fan cables to the fan headers to prevent your CPU and system from overheating. Overheating may result in damage to the CPU or the system may hang.
•• Thesefanheadersarenotconfigurationjumperblocks.Donotplaceajumpercapontheheaders.
5)BAT (Battery)
The battery provides power to keep the values (such as BIOS configurations, date, and time information) in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low level, or the CMOS values may not be accurate or may be lost.
You may clear the CMOS values by removing the battery:
1. Turn off your computer and unplug the power cord.
2. Gently remove the battery from the battery holder and wait for one minute.
(Oruseametalobjectlikeascrewdrivertotouchthepositiveandnegative terminals of the battery holder, making them short for 5 seconds.)
3. Replace the battery.
4. Plug in the power cord and restart your computer.
•• Always turn off your computer and unplug the power cord before replacing the battery.
•• Replace the battery with an equivalent one. Danger of explosion if the battery is replaced with an incorrect model.
•• Contact the place of purchase or local dealer if you are not able to replace the battery by yourself
|
or uncertain about the battery model. |
|
•• |
When installing the battery, note the orientation of the positive side (+) and the negative side (-) |
|
|
of the battery (the positive side should face up). |
|
•• |
Used batteries must be handled in accordance with local environmental regulations. |
|
|
- 23 - |
Hardware Installation |
6)SATA3 0/1/2/3/4/5 (SATA 6Gb/s Connectors)
The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA 1.5Gb/s standard. Each SATA connector supports a single SATA device. The Intel® Z87j/H87k Chipset supports RAID 0, RAID 1, RAID 5, and RAID 10. Refer to Chapter 3, "Configuring SATA hard drives," for instructions on configuring a RAID array.
SATA3 |
Pin No. |
Definition |
||
1 |
0 |
1 |
GND |
|
3 |
2 |
2 |
TXP |
|
5 |
4 |
|||
3 |
TXN |
|||
|
|
|||
1 |
7 |
4 |
GND |
|
|
|
5 |
RXN |
|
1 |
7 |
6 |
RXP |
|
|
|
7 |
GND |
|
1 |
7 |
|
|
•• ARAID 0 or RAID 1 configuration requires at least two hard drives. If more than two hard drives are to be used, the total number of hard drives must be an even number.
•• ARAID 5 configuration requires at least three hard drives. (The total number of hard drives does not have to be an even number.)
•• A RAID 10 configuration requires four hard drives.
7)CLR_CMOS (Clear CMOS Jumper)
Use this jumper to clear the BIOS configuration and reset the CMOS values to factory defaults. To clear the CMOS values, use a metal object like a screwdriver to touch the two pins for a few seconds.
Open: Normal
Short: Clear CMOS Values
•• Always turn off your computer and unplug the power cord from the power outlet before clearing the CMOS values.
•• Aftersystemrestart,gotoBIOSSetuptoloadfactorydefaults(selectLoadOptimizedDefaults)or manuallyconfiguretheBIOSsettings(refertoChapter2,"BIOSSetup,"forBIOSconfigurations).
Hardware Installation |
- 24 - |
8)F_PANEL (Front Panel Header)
Connect the power switch, reset switch, speaker, chassis intrusion switch/sensor and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.
Power LED Power Switch
Speaker
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PLED+ PLED |
|
-PW |
|
SPEAK+ |
|
|
-SPEAK |
|||||||||
|
|
|
|
|
|||||||||||||
|
|
|
|
PW+ |
|
|
|
|
|
|
|
|
|
|
|
|
|
- |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
20 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
19 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
HD- |
|
|
|
|
CI+ |
- |
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
LED+ LED LED- |
||||||||
|
|
|
|
|
- |
|
|
|
|||||||||
|
|
|
RES+ |
|
|
|
_ _ |
|
|
|
|
||||||
|
HD+ RES- |
|
|
CI |
|
|
|
PWR PWR PWR_ |
|||||||||
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Hard Drive |
|
|
Reset |
|
|
|
|
Power LED |
|
||||||||
Activity LED |
|
|
Switch |
|
Chassis Intrusion |
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
Header |
|
•• PLED/PWR_LED (Power LED, Yellow/Purple):
System Status |
LED |
S0 |
On |
S3/S4/S5 |
Off |
Connects to the power status indicator on the chassis front panel. The LED is on when the system is operating. The LED is off when the system is in S3/
S4 sleep state or powered off (S5).
•• PW (Power Switch, Red):
Connects to the power switch on the chassis front panel. You may configure the way to turn off your system using the power switch (refer to Chapter 2, "BIOS Setup," "Power Management," for more information).
•• SPEAK (Speaker, Orange):
Connects to the speaker on the chassis front panel. The system reports system startup status by issuing a beep code. One single short beep will be heard if no problem is detected at system startup.
•• HD (Hard Drive Activity LED, Blue):
Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data.
•• RES (Reset Switch, Green):
Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart.
•• CI (Chassis Intrusion Header, Gray):
Connects to the chassis intrusion switch/sensor on the chassis that can detect if the chassis cover has been removed. This function requires a chassis with a chassis intrusion switch/sensor.
The front panel design may differ by chassis. A front panel module mainly consists of power switch,
reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assignments are matched correctly.
- 25 - |
Hardware Installation |
9)F_AUDIO (Front Panel Audio Header)
The front panel audio header supports Intel High Definition audio (HD) andAC'97 audio. You may connect your chassis front panel audio module to this header. Make sure the wire assignments of the module connector match the pin assignments of the motherboard header. Incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it.
|
|
|
|
For HD Front Panel Audio: |
For AC'97 Front Panel Audio: |
||||
|
|
|
|
Pin No. |
Definition |
|
Pin No. |
Definition |
|
9 |
1 |
|
1 |
MIC2_L |
|
1 |
MIC |
|
|
|
|
|
|
2 |
GND |
|
2 |
GND |
|
|
|
|
|
3 |
MIC2_R |
|
3 |
MIC Power |
|
|
|
|
|
|
|
|
|
|
|
10 |
2 |
|
|
|
|
|
|
|
|
4 |
-ACZ_DET |
4 |
NC |
||||||
|
|
|
|
5 |
LINE2_R |
|
5 |
Line Out (R) |
|
|
|
|
|
6 |
GND |
|
6 |
NC |
|
|
|
|
|
7 |
FAUDIO_JD |
|
7 |
NC |
|
|
|
|
|
8 |
No Pin |
|
8 |
No Pin |
|
|
|
|
|
9 |
LINE2_L |
|
9 |
Line Out (L) |
|
|
|
|
|
10 |
GND |
|
10 |
NC |
|
•• The front panel audio header supports HD audio by default. If your chassis provides an AC'97 front panel audio module, refer to the instructions on how to activate AC'97 functionality via the audio software in Chapter 6, "Configuring 2/4/5.1/7.1-Channel Audio."
•• Audio signals will be present on both of the front and back panel audio connections simultaneously.
If you want to mute the back panel audio (only supported when using an HD front panel audio module), refer to Chapter 6, "Configuring 2/4/5.1/7.1-Channel Audio."
•• Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug. For information about connecting the front panel audio module that has different wire assignments, please contact the chassis manufacturer.
10)SPDIF_IN (S/PDIF In Header)
This header supports digital S/PDIF In and can connect to an audio device that supports digital audio out via an optional S/PDIF In cable. For purchasing the optional S/PDIF In cable, please contact the local dealer.
|
Pin No. |
Definition |
1 |
1 |
Power |
|
2 |
SPDIFI |
|
3 |
GND |
Hardware Installation |
- 26 - |
11)SPDIF_O (S/PDIF Out Header)
This header supports digital S/PDIF Out and connects a S/PDIF digital audio cable (provided by expansion cards) for digital audio output from your motherboard to certain expansion cards like graphics cards and sound cards. For example, some graphics cards may require you to use a S/PDIF digital audio cable for digital audio output from your motherboard to your graphics card if you wish to connect an HDMI display to the graphics card and have digital audio output from the HDMI display at the same time.
For information about connecting the S/PDIF digital audio cable, carefully read the manual for your expansion card.
|
Pin No. |
Definition |
1 |
1 |
SPDIFO |
|
2 |
GND |
12)F_USB30 (USB 3.0/2.0 Header)
The header conforms to USB 3.0/2.0 specification and can provide two USB ports. For purchasing the optional 3.5" front panel that provides two USB 3.0/2.0 ports, please contact the local dealer.
|
|
Pin No. |
Definition |
Pin No. |
Definition |
|
|
1 |
VBUS |
11 |
D2+ |
20 |
1 |
2 |
SSRX1- |
12 |
D2- |
|
|
3 |
SSRX1+ |
13 |
GND |
|
|
4 |
GND |
14 |
SSTX2+ |
|
|
5 |
SSTX1- |
15 |
SSTX2- |
|
|
6 |
SSTX1+ |
16 |
GND |
11 |
10 |
7 |
GND |
17 |
SSRX2+ |
8 |
D1- |
18 |
SSRX2- |
||
|
|
9 |
D1+ |
19 |
VBUS |
|
|
10 |
NC |
20 |
No Pin |
Prior to installing the USB bracket, be sure to turn off your computer and unplug the power cord from the power outlet to prevent damage to the USB bracket.
- 27 - |
Hardware Installation |
13)F_USB1/F_USB2/F_USB3 (USB 2.0/1.1 Headers)
The headers conform to USB 2.0/1.1 specification. Each USB header can provide two USB ports via an optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer.
|
|
|
|
|
Pin No. |
Definition |
|
|
|
|
|
1 |
Power (5V) |
9 |
|
|
|
1 |
2 |
Power (5V) |
|
|
|
||||
|
|
|
3 |
USB DX- |
||
10 |
|
|
|
2 |
||
|
|
|
|
|
4 |
USB DY- |
|
|
|
|
|
||
|
|
|
|
|
||
|
|
|
|
|
5 |
USB DX+ |
|
|
|
|
|
6 |
USB DY+ |
|
|
|
|
|
7 |
GND |
|
|
|
|
|
8 |
GND |
|
|
|
|
|
9 |
No Pin |
|
|
|
|
|
10 |
NC |
•• Do not plug the IEEE 1394 bracket (2x5-pin) cable into the USB 2.0/1.1 header.
•• Prior to installing the USB bracket, be sure to turn off your computer and unplug the power cord from the power outlet to prevent damage to the USB bracket.
14)COMA (Serial Port Header)
The COM header can provide one serial port via an optional COM port cable. For purchasing the optional COM port cable, please contact the local dealer.
|
|
|
|
|
Pin No. |
Definition |
|
|
|
|
|
1 |
NDCD- |
|
|
|
|
|
2 |
NSIN |
9 |
|
|
|
1 |
3 |
NSOUT |
10 |
|
|
|
2 |
4 |
NDTR- |
|
|
|
|
|
5 |
GND |
|
|
|
|
|
||
|
|
|
|
|
6 |
NDSR- |
|
|
|
|
|
7 |
NRTS- |
|
|
|
|
|
8 |
NCTS- |
|
|
|
|
|
9 |
NRI- |
|
|
|
|
|
10 |
No Pin |
Hardware Installation |
- 28 - |
15)LPT (Parallel Port Header)
The LPT header can provide one parallel port via an optional LPT port cable. For purchasing the optional LPT port cable, please contact the local dealer.
25 |
|
|
|
|
1 |
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
26 |
|
|
|
|
2 |
|
|
|
|
|
|
|
|
|||
Pin No. |
Definition |
|
Pin No. |
|
Definition |
|||
1 |
STB- |
|
14 |
|
GND |
|||
2 |
AFD- |
|
15 |
|
PD6 |
|||
3 |
PD0 |
|
16 |
|
GND |
|||
4 |
ERR- |
|
17 |
|
PD7 |
|||
5 |
PD1 |
|
18 |
|
GND |
|||
6 |
INIT- |
|
19 |
|
ACK- |
|||
7 |
PD2 |
|
20 |
|
GND |
|||
8 |
SLIN- |
|
21 |
|
BUSY |
|||
9 |
PD3 |
|
22 |
|
GND |
|||
10 |
GND |
|
23 |
|
PE |
|||
11 |
PD4 |
|
24 |
|
No Pin |
|||
12 |
GND |
|
25 |
|
SLCT |
|||
13 |
PD5 |
|
26 |
|
GND |
- 29 - |
Hardware Installation |
Hardware Installation |
- 30 - |