Gigabyte GA-H61M-S2PH User Manual

GA-H61M-S2PH

User's Manual

Rev. 1001

12ME-61MS2PH-1001R

Motherboard

GA-H61M-S2PH

Motherboard

GA-H61M-S2PH

Mar. 29, 2013

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of GIGABYTE.

ChangestothespecificationsandfeaturesinthismanualmaybemadebyGIGABYTEwithoutpriornotice.

No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission.

In order to assist in the use of this product, carefully read the User's Manual.

For product-related information, check on our website at: http://www.gigabyte.com

Identifying Your Motherboard Revision

The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0" means the revision of the motherboard is 1.0. Check your motherboard revision before updating motherboard BIOS, drivers, or when looking for technical information.

Example:

Table of Contents

GA-H61M-S2PH Motherboard Layout.............................................................................		4
GA-H61M-S2PH Motherboard Block Diagram.................................................................		5
Chapter 1 Hardware Installation......................................................................................		6
1-1	Installation Precautions.....................................................................................	6
1-2	Product Specifications......................................................................................	7
1-3	Installing the CPU.............................................................................................	9
1-4	Installing the Memory........................................................................................	9
1-5 Installing an Expansion Card..........................................................................		10
1-6	Back Panel Connectors..................................................................................	10
1-7	Internal Connectors........................................................................................	11
Chapter 2 BIOS Setup...................................................................................................		15
2-1	Startup Screen................................................................................................	16
2-2	M.I.T................................................................................................................	16
2-3	System............................................................................................................	20
2-4	BIOS Features................................................................................................	21
2-5	Peripherals......................................................................................................	24
2-6	Power Management........................................................................................	26
2-7	Save & Exit.....................................................................................................	27
Chapter 3 Drivers Installation........................................................................................		28
Regulatory Statements..............................................................................................		29
Contact Us.................................................................................................................		32

- 3 -

GA-H61M-S2PH Motherboard Layout

KB_MS

LPT

VGA COMA

USB_HDMI

USB_LAN

ATX_12V

DDR3 1

DDR3 2

CPU_FAN

LGA1155

ATX

Realtek

GbE LAN

AUDIO		BAT	GA-H61M-S2PH
	PCIEX16
SuperiTE I/O	PCIEX1		PCIe to PCI
	PCI1		PCIe to PCI
	PCI1		Intel® H61
			Bridge
CODEC	PCI2
			CLR_CMOS
F_AUDIO	COMB	F_USB2 F_USB1
SPDIF_O		SYS_FAN	F_PANEL

M_BIOS

B_BIOS

SATA2 3 2 1 0

Box Contents

55	GA-H61M-S2PH motherboard
55	Motherboard driver disk	55	Two SATA cables
55	User's Manual	55	I/O Shield

The box contents above are for reference only and the actual items shall depend on the product package you obtain. The box contents are subject to change without notice.

- 4 -

GA-H61M-S2PH Motherboard Block Diagram

1 PCI Express x16

PCIe CLK

(100 MHz)

PCI Express Bus

x16

D-Sub

HDMI

PCI Express Bus

PCIe CLK

(100 MHz)

Realtek

PCIe to

GbE LAN

PCI Bridge

1 PCI

Express

RJ45

LAN

PCI Bus

	CPU CLK+/- (100 MHz)
LGA1155 CPU		DDR3 1333/1066/800 MHz
		DDR3 1333/1066/800 MHz
			Dual Channel Memory
			Dual Channel Memory

DMI 2.0

FDI

Dual BIOS

Intel® H61

4 SATA 3Gb/s

8 USB 2.0/1.1

LPC

iTE

LPT

Bus

COM

Super I/O

CODEC

PS/2 KB/Mouse

PCI CLK

(33 MHz)

2 PCI

(Center/Subwoofer	(Front	S/PDIFOut
Out)Speaker	Out)Speaker Out)Speaker
MIC	(Rear
MIC	Line
	In
	Out
	Line

For detailed product information/limitation(s), refer to "1-2 Product Specifications."

- 5 -

Chapter 1 Hardware Installation

1-1 Installation Precautions

The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's manual and follow these procedures:

•• Prior to installation, make sure the chassis is suitable for the motherboard.

•• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or warranty sticker provided by your dealer. These stickers are required for warranty validation.

•• Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components.

•• When connecting hardware components to the internal connectors on the motherboard, make sure they are connected tightly and securely.

•• When handling the motherboard, avoid touching any metal leads or connectors.

•• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap, keep your hands dry and first touch a metal object to eliminate static electricity.

•• Prior to installing the motherboard, please have it on top of an antistatic pad or within an electrostatic shielding container.

•• Before unplugging the power supply cable from the motherboard, make sure the power supply has been turned off.

•• Before turning on the power, make sure the power supply voltage has been set according to the local voltage standard.

•• Before using the product, please verify that all cables and power connectors of your hardware components are connected.

•• To prevent damage to the motherboard, do not allow screws to come in contact with the motherboard circuit or its components.

•• Make sure there are no leftover screws or metal components placed on the motherboard or within the computer casing.

•• Do not place the computer system on an uneven surface.

•• Do not place the computer system in a high-temperature environment.

•• Turning on the computer power during the installation process can lead to damage to system components as well as physical harm to the user.

•• If you are uncertain about any installation steps or have a problem related to the use of the product, please consult a certified computer technician.

- 6 -

1-2	Product Specifications

	CPU	Support for Intel® Core™ i7 processors/Intel® Core™ i5 processors/
		Intel® Core™ i3 processors/Intel® Pentium® processors/Intel® Celeron® processors
		in the LGA1155 package
		(Go to GIGABYTE's website for the latest CPU support list.)
		L3 cache varies with CPU
	Chipset	Intel® H61 Express Chipset
	Memory	2 x 1.5V DDR3 DIMM sockets supporting up to 16 GB of system memory
		* Due to a Windows 32-bit operating system limitation, when more than 4 GB of physical
		memory is installed, the actual memory size displayed will be less than the size of
		the physical memory installed.

Dual channel memory architecture

Support for DDR3 1333/1066/800 MHz memory modulesSupport for non-ECC memory modules

Support for Extreme Memory Profile (XMP) memory modules

		* To support XMP memory, you must install an Intel 22nm (Ivy Bridge) CPU.
	(Go to GIGABYTE's website for the latest supported memory speeds and memory
	modules.)
Onboard	Integrated Graphics Processor:
Graphics	-	1 x D-Sub port
	-	1 x HDMI port, supporting a maximum resolution of 1920x1200
		* Support for HDMI 1.4 version.
	-	Maximum shared memory of 1 GB

Audio		Realtek® ALC887 codec
	High Definition Audio
		2/4/5.1/7.1-channel

*To configure 7.1-channel audio, you have to use an HD front panel audio module and enable the multi-channel audio feature through the audio driver.

Support for S/PDIF Out

LAN	Realtek® GbE LAN chip (10/100/1000 Mbit)
Expansion Slots	1 x PCI Express x16 slot, running at x16
	(The PCI Express x16 slot conforms to PCI Express 3.0 standard.)
		* Whether PCI Express 3.0 is supported depends on CPU and graphics card compatibility.
	1 x PCI Express x1 slot
	(The PCI Express x1 slot conforms to PCI Express 2.0 standard.)
	2 x PCI slots
Storage Interface	Chipset:
	-	4 x SATA 3Gb/s connectors supporting up to 4 SATA 3Gb/s devices
USB	Chipset:
	-	Up to 8 USB 2.0/1.1 ports (4 ports on the back panel, 4 ports available through
		the internal USB headers)
Internal	1 x 24-pin ATX main power connector
Connectors	1 x 4-pin ATX 12V power connector
	4 x SATA 3Gb/s connectors
	1 x CPU fan header
	1 x system fan header
	1 x front panel header

		- 7 -

Internal		1 x front panel audio header
Connectors		2 x USB 2.0/1.1 headers
	1 x serial port header
	1 x S/PDIF Out header
	1 x Clear CMOS jumper
Back Panel		1 x PS/2 keyboard port
Connectors		1 x PS/2 mouse port
	1 x parallel port
	1 x serial port
	1 x D-Sub port
	1 x HDMI port
	4 x USB 2.0/1.1 headers
	1 x RJ-45 port
	3 x audio jacks (Line In/Line Out/Microphone)
I/O Controller		iTE I/O Controller Chip

Hardware		System voltage detection
Monitor		CPU/System temperature detection
	CPU/System fan speed detection
	CPU overheating warning
	CPU/System fan fail warning
	CPU/System fan speed control
		* Whether the CPU/system fan speed control function is supported will depend on the
		CPU/system cooler you install.
BIOS		2 x 32 Mbit flash
	Use of licensed AMI EFI BIOS
	Support for DualBIOS™
	PnP 1.0a, DMI 2.0, SM BIOS 2.6, ACPI 2.0a
Unique Features		Support for @BIOS
		Support for Q-Flash
	Support for Xpress Recovery2
	Support for EasyTune
		* Available functions in EasyTune may differ by motherboard model.
	Support for ON/OFF Charge
Bundled	Norton Internet Security (OEM version)
Software	Norton Internet Security (OEM version)
Software
Operating	Support for Windows 8/7/XP
System	Support for Windows 8/7/XP
System
Form Factor		Micro ATX Form Factor; 24.4cm x 20cm

*GIGABYTE reserves the right to make any changes to the product specifications and product-related information without prior notice.

*Please visit the Support & Downloads\Utility page on GIGABYTE's website to check the supported operating system(s) for the software listed in the "Unique Features" and "Bundled Software" columns.

-8 -

1-3	Installing the CPU
	Read the following guidelines before you begin to install the CPU:
	••	Make sure that the motherboard supports the CPU.
	••	(Go to GIGABYTE's website for the latest CPU support list.)
	••	Always turn off the computer and unplug the power cord from the power outlet before installing the
		CPU to prevent hardware damage.
	••	Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may
		locate the notches on both sides of the CPU and alignment keys on the CPU socket.)
	••	Apply an even and thin layer of thermal grease on the surface of the CPU.
	••	Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage
		of the CPU may occur.
	••	Set the CPU host frequency in accordance with the CPU specifications. It is not recommended
		that the system bus frequency be set beyond hardware specifications since it does not meet the
		standard requirements for the peripherals. If you wish to set the frequency beyond the standard
		specifications, please do so according to your hardware specifications including the CPU, graphics
		card, memory, hard drive, etc.

Installing the CPU

Locate the alignment keys on the motherboard CPU socket and the notches on the CPU.

	LGA1155 CPU Socket		LGA1155 CPU
Alignment Key	Alignment Key	Notch	Notch
Alignment Key	Alignment Key

Pin One Corner of the CPU Socket

Triangle Pin One Marking on the CPU

Do not remove the CPU socket cover before inserting the CPU. It may pop off from the load plate automatically during the process of re-engaging the lever after you insert the CPU.

1-4 Installing the Memory

Read the following guidelines before you begin to install the memory:

•• Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips be used.

(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)

•• Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage.

•• Memory modules have a foolproof design. A memory module can be installed in only one direction. If you are unable to insert the memory, switch the direction.

Dual Channel Memory Configuration

This motherboard provides two DDR3 memory sockets and supports Dual Channel Technology. After the memory is installed, the BIOS will automatically detect the specifications and capacity of the memory. Enabling Dual

Channel memory mode will double the original memory bandwidth.

The two DDR3 memory sockets are divided into two channels and each channel has one memory socket as following:

Channel A: DDR3_1Channel B: DDR3_2

Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode.

1.Dual Channel mode cannot be enabled if only one DDR3 memory module is installed.

2.When enabling Dual Channel mode with two memory modules, it is recommended that memory of the same capacity, brand, speed, and chips be used for optimum performance.

-9 -

1-5 Installing an Expansion Card

Read the following guidelines before you begin to install an expansion card:

•• Make sure the motherboard supports the expansion card. Carefully read the manual that came with your expansion card.

•• Always turn off the computer and unplug the power cord from the power outlet before installing an

expansion card to prevent hardware damage.

1-6 Back Panel Connectors

PS/2 Keyboard and PS/2 Mouse Port

Use the upper port (green) to connect a PS/2 mouse and the lower port (purple) to connect a PS/2 keyboard.

Parallel Port

Use the parallel port to connect devices such as a printer, scanner and etc. The parallel port is also called a printer port.

Serial Port

Use the serial port to connect devices such as a mouse, modem or other peripherals.

D-Sub Port

The D-Sub port supports a 15-pin D-Sub connector. Connect a monitor that supports D-Sub connection to this port.

USB 2.0/1.1 Port

The USB port supports the USB 2.0/1.1 specification. Use this port for USB devices such as a USB keyboard/mouse, USB printer, USB flash drive and etc.

HDMI Port

HDMI (High-Definition Multimedia Interface) is an all-digital audio/video interface capable of transmitting uncompressed audio/video signals. The HDMI port is HDCP compliant and supports Dolby True HD and DTS HD Master Audio formats. It also supports up to 192KHz/24bit 8-channel LPCM audio output. You can use this port to connect your HDMI-supported audio/video device. The maximum supported resolution is 1920x1200, but the actual resolutions supported are dependent on the monitor being used.

After installing the HDMI device, make sure to set the default sound playback device to HDMI. (The

item name may differ depending on your operating system.)

RJ-45 LAN Port

The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following describes the states of the LAN port LEDs.

Connection/

Connection/Speed LED:

Activity LED:

Speed LED

Activity LED

State

Description

State

Description

Orange

1 Gbps data rate

Blinking

Data transmission or receiving is occurring

Green

100 Mbps data rate

Off

No data transmission or receiving is occurring

Off

10 Mbps data rate

LAN Port

•• When removing the cable connected to a back panel connector, first remove the cable from your device and then remove it from the motherboard.

•• When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent an electrical short inside the cable connector.

- 10 -

+ 22 hidden pages