Gigabyte GA-H55M-S2V (rev. 1.4) User Manual [ru]

GA-H55M-S2V GA-H55M-S2

LGA1156 socket motherboard for Intel® Core™ i7 processors/Intel® Core™ i5 processors/Intel® Core™ i3 processors/Intel® Pentium® processors

User's Manual

Rev. 1401

12ME-H55MS2V-1401R

Oct. 1, 2010

Motherboard

GA-H55M-S2V/GA-H55M-S2

Motherboard

Oct. 1, 2010

GA-H55M-S2V

GA-H55M-S2

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of GIGABYTE.

Changes to the specications and features in this manual may be made by GIGABYTE with-

out prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or

published in any form or by any means without GIGABYTE's prior written permission.

Documentation Classications

In order to assist in the use of this product, GIGABYTE provides the following types of documentations:

 For detailed product information, carefully read the User's Manual.  For instructions on how to use GIGABYTE's unique features, read or download the information on/from the Support&Downloads\Motherboard\Technology Guide page on our website.

For product-related information, check on our website at:

http://www.gigabyte.com

Identifying Your Motherboard Revision

The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0"

means the revision of the motherboard is 1.0. Check your motherboard revision before updating

motherboard BIOS, drivers, or when looking for technical information.

Example:

- 4 -

Table of Contents

Box Contents ...................................................................................................................6

Optional Items .................................................................................................................6

GA-H55M-S2V/GA-H55M-S2 Motherboard Layout .........................................................7

GA-H55M-S2V/GA-H55M-S2 Motherboard Block Diagram ............................................8

Chapter 1 Hardware Installation .....................................................................................9

1-1 Installation Precautions ....................................................................................9

1-2 Product Specications .................................................................................... 10

1-3 Installing the CPU and CPU Cooler ............................................................... 12

1-3-1 Installing the CPU ...................................................................................................12

1-3-2 Installing the CPU Cooler .......................................................................................14

1-4 Installing the Memory .....................................................................................15

1-4-1 Dual Channel Memory Conguration .....................................................................15

1-4-2 Installing a Memory ...............................................................................................16

1-5 Installing an Expansion Card ......................................................................... 17

1-6 Back Panel Connectors .................................................................................. 18

1-7 Internal Connectors ........................................................................................ 19

Chapter 2 BIOS Setup ..................................................................................................27

2-1 Startup Screen ............................................................................................... 28

2-2 The Main Menu .............................................................................................. 29

2-3 MB Intelligent Tweaker(M.I.T.) ........................................................................ 31

2-4 Standard CMOS Features .............................................................................. 39

2-5 Advanced BIOS Features .............................................................................. 41

2-6 Integrated Peripherals .................................................................................... 43

2-7 Power Management Setup ............................................................................. 46

2-8 PC Health Status ............................................................................................ 48

2-9 Load Fail-Safe Defaults .................................................................................. 50

2-10 Load Optimized Defaults ................................................................................ 50

2-11 Set Supervisor/User Password ...................................................................... 51

2-12 Save & Exit Setup .......................................................................................... 52

2-13 Exit Without Saving ........................................................................................ 52

- 5 -

Chapter 3 Drivers Installation ........................................................................................53

3-1 Installing Chipset Drivers ............................................................................... 53

3-2 Application Software ...................................................................................... 54

3-3 Technical Manuals .......................................................................................... 54

3-4 Contact ........................................................................................................... 55

3-5 System ........................................................................................................... 55

3-6 Download Center ........................................................................................... 56

3-7 New Utilities ................................................................................................... 56

Chapter 4 Unique Features ...........................................................................................57

4-1 Xpress Recovery2 .......................................................................................... 57

4-2 BIOS Update Utilities ..................................................................................... 60

4-2-1 Updating the BIOS with the Q-Flash Utility .............................................................60

4-2-2 Updating the BIOS with the @BIOS Utility .............................................................63

4-3 EasyTune 6 .................................................................................................... 64

4-4 Q-Share .......................................................................................................... 65

4-5 Auto Green ..................................................................................................... 66

Chapter 5 Appendix ......................................................................................................67

5-1 Conguring Audio Input and Output ............................................................... 67

5-1-1 Conguring 2/4/5.1/7.1-Channel Audio ...................................................................67

5-1-2 Conguring Microphone Recording ........................................................................70

5-1-3 Using the Sound Recorder .....................................................................................72

5-2 Troubleshooting.............................................................................................. 73

5-2-1 Frequently Asked Questions ..................................................................................73

5-2-2 Troubleshooting Procedure ....................................................................................74

5-3 Regulatory Statements ................................................................................... 76

- 6 -

Box Contents

GA-H55M-S2V or GA-H55M-S2 motherboard

Motherboard driver disk

User's Manual

Two SATA cables

I/O Shield

Optional Items

2-port USB 2.0 bracket (Part No. 12CR1-1UB030-5*R)

2-port SATA power cable (Part No. 12CF1-2SERPW-0*R)

COM port cable (Part No. 12CF1-1CM001-3*R)

• The box contents above are for reference only and the actual items shall depend on the product package you obtain.

The box contents are subject to change without notice.

• The motherboard image is for reference only.

j Only for GA-H55M-S2V.

- 7 -

GA-H55M-S2V/GA-H55M-S2 Motherboard Layout

CPU_FAN

LGA1156

ATX

F_AUDIO

AUDIO

M_BIOS

PCIEX1

DDR3_1

DDR3_2

BAT

F_PANEL

iTE

IT8720

ATX_12V

Intel® H55

SATA2_0

PCI1

CODEC

B_BIOS

F_USB2

USB_LAN

PCIEX16

F_USB1

Realtek

RTL8111E

KB_MS

R_USB3

PCI2

GA-H55M-S2

CLR_CMOS

SYS_FAN

SATA2_3

SATA2_1SATA2_4

SATA2_2SATA2_5

R_USB2

R_USB1

GA-H55M-S2V

DVIjVGA

LEVEL SHIFTER

j Only for GA-H55M-S2V.

COMA

- 8 -

GA-H55M-S2V/GA-H55M-S2 Motherboard Block Diagram

CODEC

PS/2 KB/Mouse

LGA1156

CPU

DMI Interface

Intel® H55

2 PCI

PCI Bus

PCI CLK

(33 MHz)

PCIe CLK

(100 MHz)

PCI Express Bus

iTE

IT8720

CPU CLK+/- (133 MHz)

6 SATA 3Gb/s

1 PCI Express x16

Dual BIOS

12 USB 2.0/1.1

LPC

Bus

DDR3 1666 (O.C.)/1333/1066/800 MHz

Dual Channel Memory

LAN

RJ45

Realtek

RTL8111E

1 PCI Express x1

PCI Express Bus

x16

PCIe CLK

(100 MHz)

D-Sub

FDI Interface

Line In (Rear Speakcer Out )

Line Out (Front Speakcer Out )

MIC (Center/Subwoofer Speakcer Out )

DVI

j Only for GA-H55M-S2V.

COM

- 9 - Hardware Installation

1-1 Installation Precautions

The motherboard contains numerous delicate electronic circuits and components which can

become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read

the user's manual and follow these procedures:

• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or

warranty sticker provided by your dealer. These stickers are required for warranty validation.

• Always remove the AC power by unplugging the power cord from the power outlet before

installing or removing the motherboard or other hardware components.

• When connecting hardware components to the internal connectors on the motherboard,

make sure they are connected tightly and securely.

• When handling the motherboard, avoid touching any metal leads or connectors.

• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic com-

ponents such as a motherboard, CPU or memory. If you do not have an ESD wrist strap,

keep your hands dry and rst touch a metal object to eliminate static electricity.

• Prior to installing the motherboard, please have it on top of an antistatic pad or within an

electrostatic shielding container.

• Before unplugging the power supply cable from the motherboard, make sure the power sup-

ply has been turned off.

• Before turning on the power, make sure the power supply voltage has been set according to

the local voltage standard.

• Before using the product, please verify that all cables and power connectors of your hard-

ware components are connected.

• To prevent damage to the motherboard, do not allow screws to come in contact with the

motherboard circuit or its components.

• Make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.

• Do not place the computer system on an uneven surface

• Do not place the computer system in a high-temperature environment.

• Turning on the computer power during the installation process can lead to damage to sys-

tem components as well as physical harm to the user.

• If you are uncertain about any installation steps or have a problem related to the use of the

product, please consult a certied computer technician.

Chapter 1 Hardware Installation

- 10 -Hardware Installation

1-2 Product Specications

CPU  Support for Intel® Core™ i7 processors/Intel® Core™ i5 processors/Intel® Core™ i3 processors/Intel® Pentium® processors in the LGA1156 package (Go to GIGABYTE's website for the latest CPU support list.)  L3 cache varies with CPU

Chipset



 Intel® H55 Express Chipset

Memory  2 x 1.5V DDR3 DIMM sockets supporting up to 16 GB of system memory

(Note 1)

 Dual channel memory architecture  Support for DDR3 1666 (O.C.)/1333/1066/800 MHz memory modules  Support for non-ECC memory modules  Support for Extreme Memory Prole (XMP) memory modules  (Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)

Onboard Graphics  Integrated in the Chipset:

- 1 x DVI-D port

(Note 2)(Note 3)

- 1 x D-Sub port

(Note 2)

Audio

   

Realtek ALC888B codec





High Denition Audio

2/4/5.1/7.1-channel

(Note 4)

LAN



 1 x Realtek RTL8111E chip (10/100/1000 Mbit)

Expansion Slots  1 x PCI Express x16 slot, running at x16

(The PCIEX16 slot conforms to PCI Express 2.0 standard.)  1 x PCI Express x1 slot  2 x PCI slots

Storage Interface  Chipset:

- 6 x SATA 3Gb/s connectors supporting up to 6 SATA 3Gb/s devices

USB  Chipset: - Up to 12 USB 2.0/1.1 ports (8 on the back panel, 4 via the USB brackets connected to the internal USB headers)

Internal



1 x 24-pin ATX main power connector Connectors  1 x 4-pin ATX 12V power connector  6 x SATA 3Gb/s connectors  1 x CPU fan header  1 x system fan header  1 x front panel header  1 x front panel audio header  2 x USB 2.0/1.1 headers  1 x serial port header

 1 x clearing CMOS jumper

Only for GA-H55M-S2V.

- 11 - Hardware Installation

j Only for GA-H55M-S2V.

(Note 1) Due to Windows 32-bit operating system limitation, when more than 4 GB of physical memory is installed, the actual memory size displayed will be less than 4 GB. (Note 2)

To use the onboard DVI-D/D-Sub port, you must install an Intel CPU with integrated graphics.

(Note 3) The DVI-D port does not support D-Sub connection by adapter.

(Note 4) To congure 7.1-channel audio, you have to use an HD front panel audio module and enable the

multi-channel audio feature through the audio driver.

(Note 5) Whether the CPU fan speed control function is supported will depend on the CPU cooler you install. (Note 6) Available functions in EasyTune may differ by motherboard model.

Back Panel  1 x PS/2 keyboard port

Connectors

 1 x PS/2 mouse port



1 x D-Sub port

(Note 2)



1 x DVI port

(Note 2)(Note 3)

 8 x USB 2.0/1.1 ports  1 x RJ-45 port  3 x audio jacks (Line In/Line Out/Microphone)

I/O Controller  iTE IT8720 chip

Hardware Monitor  System voltage detection  CPU temperature detection  CPU/System fan speed detection  CPU overheating warning  CPU/System fan fail warning  CPU fan speed control

(Note 5)

BIOS



2 x 8 Mbit ash

 Use of licensed AWARD BIOS  Support for DualBIOS

™

 PnP 1.0a, DMI 2.0, SM BIOS 2.4, ACPI 1.0b

Unique Features  Support for @BIOS

 Support for Q-Flash  Support for Xpress BIOS Rescue  Support for Download Center  Support for Xpress Install  Support for Xpress Recovery2  Support for EasyTune

(Note 6)



Support for Auto Green  Support for ON/OFF Charge  Support for Q-Share

Bundled Software  Norton Internet Security (OEM version)

Operating System  Support for Microsoft® Windows 7/Vista/XP

Form Factor  Micro ATX Form Factor; 24.4cm x 21.0cm

- 12 -Hardware Installation

1-3 Installing the CPU and CPU Cooler

1-3-1 Installing the CPU

A. Locate the alignment keys on the motherboard CPU socket and the notches on the CPU.

NotchNotch

Alignment Key

LGA1156 CPU

LGA1156 CPU Socket

Pin One Corner of the CPU Socket

Triangle Pin One Marking on the CPU

Read the following guidelines before you begin to install the CPU:

• Make sure that the motherboard supports the CPU. (Go to GIGABYTE's website for the latest CPU support list.)

• Always turn off the computer and unplug the power cord from the power outlet before installing the CPU to prevent hardware damage.

• Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may locate the notches on both sides of the CPU and alignment keys on the CPU socket.)

• Apply an even and thin layer of thermal grease on the surface of the CPU.

• Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and dam-

age of the CPU may occur.

• Set the CPU host frequency in accordance with the CPU specications. It is not recommended that the system bus frequency be set beyond hardware specications since it does not meet the

standard requirements for the peripherals. If you wish to set the frequency beyond the standard specications, please do so according to your hardware specications including the CPU, graphics card, memory, hard drive, etc.

- 13 - Hardware Installation

Step 1: Gently press the CPU socket lever handle down

and away from the socket with your nger. Then

completely lift the CPU socket lever and the metal load plate will be lifted as well.

Step 3:

Hold the CPU with your thumb and index ngers.

Align the CPU pin one marking (triangle) with the pin one corner of the CPU socket (or you may align the CPU notches with the socket alignment keys) and gently insert the CPU into position.

Step 5: Push the CPU socket lever back into its locked position.

Step 4: Onc e the CPU is properly inserted, use one hand to hold the socket lever and use the other to lightly replace the load plate. When replacing the load plate, make sure the front end of the load plate is under the shoulder screw.

B. Follow the steps below to correctly install the CPU into the motherboard CPU socket.

Before installing the CPU, make sure to turn off the computer and unplug the power cord from

the power outlet to prevent damage to the CPU.

NOTE:

Hold the CPU socket lever by the handle, not the lever base portion.

Step 2: Remove the CPU socket cover as shown. Hold

your index finger down on the rear grip of the socket cover and use your thumb to lift up the front edge (next to the "REMOVE" mark) and then remove the cover. (DO NOT touch socket contacts. To protect the CPU socket, always replace the protective socket cover when the CPU is not installed.)

- 14 -Hardware Installation

1-3-2 Installing the CPU Cooler

Follow the steps below to correctly install the CPU cooler on the motherboard. (The following procedure uses Intel® boxed cooler as the example cooler.)

Step 1: Apply an even and thin layer of thermal grease on the surface of the installed CPU.

Male Push Pin

Female Push Pin

The Top of Female Push Pin

Direction of the Arrow Sign on the Male Push Pin

Step 2: Before installing the cooler, note the direction of

the arrow sign on the male push pin. (Turning the push pin along the direction of arrow is to remove the cooler, on the contrary, is to install.)

Step 3: Place the cooler atop the CPU, aligning the four

push pins through the pin holes on the motherboard. Push down on the push pins diagonally.

Step 4: You should hear a "click" when pushing down

each push pin. Check that the Male and Female push pins are joined closely. (Refer to your CPU cooler installation manual for instructions on installing the cooler.)

Use extreme care when removing the CPU cooler because the thermal grease/tape between the CPU cooler and CPU may adhere to the CPU. Inadequately removing the CPU cooler may damage the CPU.

Step 5: After the installation, check the back of the moth-

erboard. If the push pin is inserted as the picture above shows, the installation is complete.

Step 6: Finally, attach the power connector of the CPU

cooler to the CPU fan header (CPU_FAN) on the motherboard.

- 15 - Hardware Installation

1-4-1 Dual Channel Memory Conguration

This motherboard provides two DDR3 memory sockets and supports Dual Channel Technology. After the memory is installed, the BIOS will automatically detect the specications and capacity of the memory. Enabling Dual Channel memory mode will double the original memory bandwidth. The two DDR3 memory sockets are divided into two channels and each channel has one memory socket as following:

Channel 0: DDR3_1 Channel 1: DDR3_2

1-4 Installing the Memory

Read the following guidelines before you begin to install the memory:

• Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips be used.

(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)

• Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage.

• Memory modules have a foolproof design. A memory module can be installed in only one direction. If you are unable to insert the memory, switch the direction.

DDR3_1

DDR3_2

Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode.

1. Dual Channel mode cannot be enabled if only one DDR3 memory module is installed.

2. When enabling Dual Channel mode with two memory modules, it is recommended that memory of the same capacity, brand, speed, and chips be used for optimum performance.

- 16 -Hardware Installation

1-4-2 Installing a Memory

Notch

DDR3 DIMM

A DDR3 memory module has a notch, so it can only t in one direction. Follow the steps below to correctly

install your memory modules in the memory sockets.

Step 1: Note the orientation of the memory module. Spread the retaining clips at both ends of the memory socket. Place the memory module on the socket. As indicated in the picture on the left, place your ngers on the top edge of the memory, push down on the memory and insert it vertically into the memory socket.

Step 2: The clips at both ends of the socket will snap into place when the memory module is securely inserted.

Before installing a memory module, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the memory module. DDR3 and DDR2 DIMMs are not compatible to each other or DDR DIMMs. Be sure to install DDR3 DIMMs on this motherboard.

- 17 - Hardware Installation

1-5 Installing an Expansion Card

Read the following guidelines before you begin to install an expansion card:

• Make sure the motherboard supports the expansion card. Carefully read the manual that came

with your expansion card.

• Always turn off the computer and unplug the power cord from the power outlet before installing

an expansion card to prevent hardware damage.

Follow the steps below to correctly install your expansion card in the expansion slot.

1. Locate an expansion slot that supports your card. Remove the metal slot cover from the chassis back panel.

2. Align the card with the slot, and press down on the card until it is fully seated in the slot.

3. Make sure the metal contacts on the card are completely inserted into the slot.

4. Secure the card’s metal bracket to the chassis back panel with a screw.

5. After installing all expansion cards, replace the chassis cover(s).

6. Turn on your computer. If necessary, go to BIOS Setup to make any required BIOS changes for your

expansion card(s).

7. Install the driver provided with the expansion card in your operating system.

Example: Installing and Removing a PCI Express Graphics Card:

• Installing a Graphics Card: Gently push down on the top edge of the card until

it is fully inserted into the PCI Express slot. Make sure the card is securely seated in the slot and does not rock.

PCI Slot

PCI Express x16 Slot

• Removing the Card: Press the white latch at the end of the PCI Express slot to release the card and then pull the card straight up from the slot.

PCI Express x1 Slot

- 18 -Hardware Installation

1-6 Back Panel Connectors

PS/2 Keyboard and PS/2 Mouse Port

Use the upper port (green) to connect a PS/2 mouse and the lower port (purple) to connect a PS/2 keyboard.

D-Sub Port

(Note 1)

The D-Sub port supports a 15-pin D-Sub connector. Connect a monitor that supports D-Sub connection

to this port.

DVI-D Port

(Note 2)

The DVI-D port conforms to the DVI-D specication and supports

a maximum resolution of 1920x1200 (the

actual resolutions supported depend on the monitor being used).

Connect a monitor that supports DVI-D con-

nection to this port.

USB 2.0/1.1

The USB port supports the USB 2.0/1.1 specication. Use this port for USB devices such as a USB key board/mouse, USB printer, USB ash drive and etc.

RJ-45 LAN Port

The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following de-

scribes the states of the LAN port LEDs.

Only for GA-H55M-S2V (Note 1) To use the onboard DVI-D/D-Sub port, you must install an Intel CPU with integrated graphics. (Note 2) The DVI-D port does not support D-Sub connection by adapter.

Activity LED:

State Description

Blinking Data transmission or receiving is occurring

Off No data transmission or receiving is occurring

Connection/Speed LED:

State Description

Orange 1 Gbps data rate

Green 100 Mbps data rate

Off 10 Mbps data rate

Activity LED

Connection/ Speed LED

LAN Port

Line In Jack (Blue)

The default line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.

Line Out Jack (Green)

The default line out jack. Use this audio jack for a headphone or 2-channel speaker. This jack can be

used to connect front speakers in a 4/5.1/7.1-channel audio conguration.

Mic In Jack (Pink)

The default Mic in jack. Microphones must be connected to this jack.

To congure 7.1-channel audio, you have to use an HD front panel audio module and enable

the multi-channel audio feature through the audio driver. Refer to the instructions on setting up a

2/4/5.1/7.1-channel audio conguration in Chapter 5, "Conguring 2/4/5.1/7.1-Channel Audio."

• When removing the cable connected to a back panel connector, rst remove the cable from

your device and then remove it from the motherboard.

• When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent an electrical short inside the cable connector.

- 19 - Hardware Installation

1-7 Internal Connectors

Read the following guidelines before connecting external devices:

• First make sure your devices are compliant with the connectors you wish to connect.

• Before installing the devices, be sure to turn off the devices and your computer. Unplug the

power cord from the power outlet to prevent damage to the devices.

• After installing the device and before turning on the computer, make sure the device cable has been securely attached to the connector on the motherboard.

1) ATX_12V

2) ATX

3) CPU_FAN

4) SYS_FAN

5) SATA2_0/1/2/3/4/5

6) F_PANEL

7) F_AUDIO

8) F_USB1/F_USB2

9) COMA

10) CLR_CMOS

11) BAT

4 8

Only for GA-H55M-S2V

- 20 -Hardware Installation

131

2412

ATX

ATX:

Pin No. Denition

13 3.3V

14 -12V

15 GND

16 PS_ON (soft On/Off)

17 GND

18 GND

19 GND

20 -5V

21 +5V

22 +5V

23 +5V (Only for 2x12-pin ATX)

24 GND (Only for 2x12-pin ATX)

Pin No. Denition

1 3.3V

2 3.3V

3 GND

4 +5V

5 GND

6 +5V

7 GND

8 Power Good

9 5VSB (stand by +5V)

10 +12V

11 +12V (Only for 2x12-pin ATX)

12 3.3V (Only for 2x12-pin ATX)

1/2) ATX_12V/ATX (2x2 12V Power Connector and 2x12 Main Power Connector)

With the use of the power connector, the power supply can supply enough stable power to all the

components on the motherboard. Before connecting the power connector, rst make sure the power

supply is turned off and all devices are properly installed. The power connector possesses a foolproof design. Connect the power supply cable to the power connector in the correct orientation. The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected, the computer will not start.

To meet expansion requirements, it is recommended that a power supply that can withstand

high power consumption be used (500W or greater). If a power supply is used that does not provide the required power, the result can lead to an unstable or unbootable system.

ATX_12V

ATX_12V:

Pin No. Denition

1 GND

2 GND

3 +12V

4 +12V

- 21 - Hardware Installation

3/4) CPU_FAN/SYS_FAN (Fan Headers)

The motherboard has a 4-pin CPU fan header (CPU_FAN) and a 3-pin system fan header (SYS_FAN).

Most fan headers possess a foolproof insertion design. When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is the ground wire). The motherboard supports CPU fan speed control, which requires the use of a CPU fan with fan speed control design. For optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.

• Be sure to connect fan cables to the fan headers to prevent your CPU and system from overheating. Overheating may result in damage to the CPU or the system may hang.

• These fan headers are not conguration jumper blocks. Do not place a jumper cap on the

headers.

CPU_FAN

DEBUG PORT

CPU_FAN:

Pin No. Denition

1 GND

2 +12V / Speed Control

3 Sense

4 Speed Control

SYS_FAN

SYS_FAN:

Pin No. Denition

1 GND

2 +12V

3 Sense

5) SATA2_0/1/2/3/4/5 (SATA 3Gb/s Connectors, Controlled by H55 Chipset)

The SATA connectors conform to SATA 3Gb/s standard and are compatible with SATA 1.5Gb/s standard.

Each SATA connector supports a single SATA device.

Pin No. Denition

1 GND

2 TXP

3 TXN

4 GND

5 RXN

6 RXP

7 GND

DEBUG PORT

G.QBOFM

SATA2_3

DEBUG PORT

G.QBOFM

DEBUG PORT

G.QBOFM

DEBUG PORT

G.QBOFM

DEBUG PORT

G.QBOFM

DEBUG PORT

G.QBOFM

SATA2_4SATA2_5

SATA2_0SATA2_1SATA2_2

Please connect the L-shaped end of th e S ATA c able to your S ATA ha rd drive.

- 22 -Hardware Installation

6) F_PANEL (Front Panel Header)

Connect the power switch, reset switch, speaker, chassis intrusion switch/sensor and system status

indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

• PW (Power Switch, Red):

Connects to the power switch on the chassis front panel. You may congure the way to turn off your

system using the power switch (refer to Chapter 2, "BIOS Setup," "Power Management Setup," for more information).

• SPEAK (Speaker, Orange): Connects to the speaker on the chassis front panel. The system reports system startup status by is-

suing a beep code. One single short beep will be heard if no problem is detected at system startup. If a problem is detected, the BIOS may issue beeps in different patterns to indicate the problem. Refer to Chapter 5, "Troubleshooting," for information about beep codes.

• HD (Hard Drive Activity LED, Blue) Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive

is reading or writing data.

• RES (Reset Switch, Green): Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer

if the computer freezes and fails to perform a normal restart.

• CI (Chassis Intrusion Header, Gray): Connects to the chassis intrusion switch/sensor on the chassis that can detect if the chassis cover

has been removed. This function requires a chassis with a chassis intrusion switch/sensor.

• MSG/PWR (Message/Power/Sleep LED, Yellow/Purple): Connects to the power status indicator on the chassis front panel. The LED

is on when the system is operating. The LED keeps blinking when the system is in S1 sleep state. The LED is off when the system is in S3/S4 sleep state or powered off (S5).

System Status LED

S0 On

S1 Blinking

S3/S4/S5 Off

The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assignments are matched correctly.

Power LED

CI-

CI+

PWR-

PWR+

MSG-

PW-

SPEAK+

SPEAK-

MSG+

PW+

Message/Power/

Sleep LED

Speaker

Power Switch

HD-

RES+

HD+

RES-

Hard Drive

Activity LED

Reset Switch

Chassis Intrusion Header

- 23 - Hardware Installation

7) F_AUDIO (Front Panel Audio Header)

The front panel audio header supports Intel High Denition audio (HD) and AC'97 audio. You may connect

your chassis front panel audio module to this header. Make sure the wire assignments of the module connector match the pin assignments of the motherboard header. Incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it.

Pin No. Denition

1 MIC2_L

2 GND

3 MIC2_R

4 -ACZ_DET

5 LINE2_R

6 GND

7 FAUDIO_JD

8 No Pin

9 LINE2_L

10 GND

Pin No. Denition

1 MIC

2 GND

3 MIC Power

4 NC

5 Line Out (R)

6 NC

7 NC

8 No Pin

9 Line Out (L)

10 NC

For HD Front Panel Audio: For AC'97 Front Panel Audio:

1 2

9 10

• The front panel audio header supports HD audio by default. If your chassis provides an AC'97 front panel audio module, refer to the instructions on how to activate AC'97 functionality via

the audio software in Chapter 5, "Conguring 2/4/5.1/7.1-Channel Audio."

• Audio signals will be present on both of the front and back panel audio connections simultaneously. If you want to mute the back panel audio (only supported when using an HD front panel

audio module), refer to Chapter 5, "Conguring 2/4/5.1/7.1-Channel Audio."

• Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug. For information about connecting the front panel audio module that has different wire assignments, please contact the chassis manufacturer.

8) F_USB1/F_USB2 (USB Headers)

The headers conform to USB 2.0/1.1 specication. Each USB header can provide two USB ports via an

optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer.

G.QBOFM

Pin No. Denition

1 Power (5V)

2 Power (5V)

3 USB DX-

4 USB DY-

5 USB DX+

6 USB DY+

7 GND

8 GND

9 No Pin

10 NC

• Do not plug the IEEE 1394 bracket (2x5-pin) cable into the USB header.

• Prior to installing the USB bracket, be sure to turn off your computer and unplug the power

cord from the power outlet to prevent damage to the USB bracket.

- 24 -Hardware Installation

10) CLR_CMOS (Clearing CMOS Jumper)

Use this jumper to clear the CMOS values (e.g. date information and BIOS congurations) and reset

the CMOS values to factory defaults. To clear the CMOS values, place a jumper cap on the two pins to temporarily short the two pins or use a metal object like a screwdriver to touch the two pins for a few seconds.

• Always turn off your computer and unplug the power cord from the power outlet before clearing the CMOS values.

• After clearing the CMOS values and before turning on your computer, be sure to remove the jumper cap from the jumper. Failure to do so may cause damage to the motherboard.

• After system restart, go to BIOS Setup to load factory defaults (select Load Optimized De- faults) or manually congure the BIOS settings (refer to Chapter 2, "BIOS Setup," for BIOS

congurations).

Open: Normal

Short: Clear CMOS Values

9) COMA (Serial Port Header)

The COM header can provide one serial port via an optional COM port cable. For purchasing the op-

tional COM port cable, please contact the local dealer.

Pin No. Denition

1 NDCD-

2 NSIN

3 NSOUT

4 NDTR-

5 GND

6 NDSR-

7 NRTS-

8 NCTS-

9 NRI-

10 No Pin

Only for GA-H55M-S2V

+ 56 hidden pages