Gigabyte GA-6BMM User Manual

BIOS Configuration

4.BIOS CONFIGURATION

Award's BIOS ROM has a built-in Setup program that allows users to modify the
basic system configuration. This type of information is stored in battery-backed
CMOS SRAM so that it retains the Setup information when the power is turned
off.

4.1. ENTERING SETUP

Power ON the computer and press <Del> immediately will allow you to enter
Setup. If the message disappears before you respond and you still wish to enter
Setup, restart the system to try again by turning it OFF then ON or pressing the
"RESET" bottom on the system case. You may also restart by simultaneously
press <Ctrl>, <Alt>, and <Del> keys.

4.2. CONTROL KEYS

Up arrow Move to previous item
Down arrow Move to next item
Left arrow Move to the item in the left hand
Right arrow Move to the item in the right hand
Esc key Main Menu - Quit and not save changes into CMOS

Status Page Setup Menu and Option Page Setup Menu -

Exit current page and return to Main Menu
PgUp key Increase the numeric value or make changes
PgDn key Decrease the numeric value or make changes
F1 key General help, only for Status Page Setup Menu and Option

Page Setup Menu
F2 key Change color from total 16 colors
F3 key Reserved
F4 key Reserved
F5 key Restore the previous CMOS value from CMOS, only for

Option Page Setup Menu
F6 key Load the default CMOS value from BIOS default table, only

for Option Page Setup Menu
F7 key Load the default
F8 key Reserved
F9 key Reserved
F10 key Save all the CMOS changes, only for Main Menu

4-1

6BMM

4.3. GETTING HELP

4.3.1. Main Menu

The on-line description of the highlighted setup function is displayed at the
bottom of the screen.

4.3.2. Status Page Setup Menu / Option Page Setup Menu

Press F1 to pop up a small help window that describes the appropriate keys to
use and the possible selections for the highlighted item. To exit the Help
Window press <Esc>.

4.4. THE MAIN MENU

Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 4.1)
will appear on the screen. The Main Menu allows you to select from nine setup
functions and two exit choices. Use arrow keys to select among the items and
press <Enter> to accept or enter the sub-menu.

Figure 4.1: Main Menu

• Standard CMOS setup

This setup page includes all the items in standard compatible BIOS.

• BIOS features setup

This setup page includes all the items of Award special enhanced
features.

4-2

BIOS Configuration

• Chipset features setup

This setup page includes all the items of chipset special features.

• Power management setup

This setup page includes all the items of Green function features.

• PNP/PCI configuration

This setup page includes all the configurations of PCI & PnP ISA
resources.

• Load BIOS defaults

Bios Defaults indicates the value of the system parameters which the

system would be in safe configuration.

• Load Performance defaults

Performance Defaults indicates the value of the system parameters
which the system would be in best performance configuration.

• Integrated peripherals

This setup page includes all onboard peripherals.

• Supervisor password

Change, set, or disable password. It allows you to limit access to the

system and Setup, or just to Setup.

• User password

Change, set, or disable password. It allows you to limit access to the
system.

• IDE HDD auto detection

Automatically configure hard disk parameters.

• Save & exit setup

Save CMOS value settings to CMOS and exit setup.

• Exit without saving

Abandon all CMOS value changes and exit setup.

4-3

6BMM

4.5. STANDARD CMOS SETUP MENU

The items in Standard CMOS Setup Menu (Figure 4.2) are divided into 9
categories. Each category includes no, one or more than one setup items. Use
the arrows to highlight the item and then use the <PgUp> or <PgDn> keys to
select the value you want in each item.

Figure 4.2: Standard CMOS Setup Menu

• Date

The date format is <day>, <month> <date> <year>.

day The day, from Sun to Sat, determined by the BIOS and is

display-only
month The month, Jan. Through Dec.
date The date, from 1 to 31 (or the maximum allowed in the month)
year The year, from 1994 through 2079

• Time

The times format in <hour> <minute> <second>. The time is calculated
base on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00.

4-4

BIOS Configuration

• Primary HDDs / Secondary HDDs

The category identifies the types of hard disk from drive C to F that has
been installed in the computer. There are two types: auto type, and user
definable type. User type is user-definable; Auto type which will
automatically detect HDD type.

Note that the specifications of your drive must match with the drive table.
The hard disk will not work properly if you enter improper information for
this category.

If you select User Type, related information will be asked to enter to the
following items. Enter the information directly from the keyboard and press
<Enter>. Such information should be provided in the documentation form
your hard disk vendor or the system manufacturer.

CYLS. Number of cylinders
HEADS number of heads
PRECOMP write precomp
LANDZONE Landing zone
SECTORS number of sectors

If a hard disk has not been installed select NONE and press <Enter>.

• Drive A type / Drive B type

The category identifies the types of floppy disk drive A or drive B that has
been installed in the computer.

None No floppy drive installed
360K, 5.25 in. 5.25 inch PC-type standard drive; 360K byte capacity.

1.2M, 5.25 in. 5.25 inch AT-type high-density drive; 1.2M byte

capacity (3.5 inch when 3 Mode is Enabled).

720K, 3.5 in. 3.5 inch double-sided drive; 720K byte capacity

1.44M, 3.5 in. 3.5 inch double-sided drive; 1.44M byte capacity.

2.88M, 3.5 in. 3.5 inch double-sided drive; 2.88M byte capacity.

4-5

6BMM

• Floppy 3 Mode Support (for Japan Area)

Disabled Normal Floppy Drive.
Drive A Drive A is 3 mode Floppy Drive.
Drive B Drive B is 3 mode Floppy Drive.
Both Drive A & B are 3 mode Floppy Drives.

• Video

The category detects the type of adapter used for the primary system
monitor that must match your video display card and monitor. Although
secondary monitors are supported, you do not have to select the type in
setup.

EGA/VGA Enhanced Graphics Adapter/Video Graphics Array. For

EGA, VGA, SVGA, or PGA monitor adapters
CGA 40 Color Graphics Adapter, power up in 40 column mode
CGA 80 Color Graphics Adapter, power up in 80 column mode
MONO

Monochrome adapter, includes high resolution

monochrome adapters

• Halt on

The category determines whether the computer will stop if an error is
detected during power up.

NO Errors The system boot will not stop for any error that may

be detected and you will be prompted

All Errors

All, But Keyboard The system boot will not stop for a keyboard error;

All, But Diskette

All, But Disk/Key The system boot will not stop for a keyboard or disk

Whenever the BIOS detects a non-fatal error the
system will be stopped

it will stop for all other errors
The system boot will not stop for a disk error; it will

stop for all other errors

4-6

BIOS Configuration

error; it will stop for all other errors

• Memory

The category is display-only which is determined by POST (Power On Self
Test) of the BIOS.

Base Memory

The POST of the BIOS will determine the amount of base (or
conventional) memory installed in the system.

The value of the base memory is typically 512 K for systems with
512 K memory installed on the motherboard, or 640 K for systems
with 640 K or more memory installed on the motherboard.

Extended Memory

The BIOS determines how much extended memory is present
during the POST.

This is the amount of memory located above 1 MB in the CPU's
memory address map.

Expanded Memory

Expanded Memory in memory defined by the Lotus / Intel /
Microsoft (LIM) standard as EMS.

Many standard DOS applications can not utilize memory above
640 K; the Expanded Memory Specification (EMS) swaps
memory, which not utilized by DOS with a section, or frame, so
these applications, can access all of the system memory.

Memory can be swapped by EMS is usually 64 K within 1 MB or
memory above 1 MB, depends on the chipset design.

Expanded memory device driver is required to use memory as
Expanded Memory.

Other Memory

This refers to the memory located in the 640 K to 1024 K address
space. This is memory that can be used for different applications.

DOS uses this area to load device drivers to keep as much base
memory free for application programs. Most use for this area is

4-7

6BMM

Shadow RAM.

4-8

BIOS Configuration

4.6. BIOS FEATURES SETUP

Figure 4.3: BIOS Features Setup

• Virus Warning

If it is set to enable, the category will flash on the screen when there is any
attempt to write to the boot sector or partition table of the hard disk drive.
The system will halt and the following error message will appear in the
mean time. You can run anti-virus program to locate the problem.

Default value is Disabled.

Enabled Activate automatically when the system boots up causing a

warning message to appear when anything attempts to
access the boot sector or hard disk partition table

Disabled No warning message to appear when anything attempts to

access the boot sector or hard disk partition table

• CPU Internal Cache / External Cache

These two categories speed up memory access. However, it depends on
CPU / chipset design. The default value is Enabled.

Enabled Enable cache
Disabled Disable cache

4-9

6BMM

Disabled

Disabled

Disabled

Disabled

X1, X2, X3

• CPU L2 Cache ECC Checking

The default value is Disabled.

Enabled Enable CPU L2 Cache ECC Checking

Disable CPU L2 Cache ECC Checking

• Quick Power On Self Test

This category speeds up Power On Self Test (POST) after you power on
the computer. If it is set to Enable, BIOS will shorten or skip some check
items during POST.

The default value is Enabled.

Enabled Enable quick POST

Normal POST

• CPU Update Data

The default value is Enabled.

Enabled Enable CPU Update Data

Normal CPU Update Data

• Boot From LAN First

The default value is Enabled.

Enabled Enable Boot From LAN First

Disable Boot From LAN First

• Boot Sequence

This category determines which drive computer searches first for the disk
operating system (i.e., DOS). Default value is A, C, SCSI.

System will first search for X1 disk drive then X2 disk drive
and then X3 disk drive.

4-10

BIOS Configuration

Disabled

• Swap Floppy Drive

The default value is Disabled.

Enabled Floppy A & B will be swapped under DOS

Floppy A & B will be normal definition

• VGA Boot From

The default value is AGP

AGP System will boot from AGP Display Card
PCI System will boot from PCI VGA Card

• Boot Up Floppy Seek

During POST, BIOS will determine the floppy disk drive installed is 40 or 80
tracks. 360 K type is 40 tracks 720 K, 1.2 M and 1.44 M are all 80 tracks.
The default value is Enabled.

Enabled BIOS searches for floppy disk drive to determine it is 40 or

80 tracks. Note that BIOS can not tell from 720 K, 1.2 M or

1.44 M drive type as they are all 80 tracks

Disabled BIOS will not search for the type of floppy disk drive by track

number. Note that there will not be any warning message if
the drive installed is 360 K

• Boot Up NumLock Status

The default value is On.

On Keypad is number keys
Off Keypad is arrow keys

• Typematic Rate Setting

The default value is Disabled.

Enabled Enable Keyboard Typematic rate setting.
Disabled Disable Keyboard Typematic rate setting.

4-11

6BMM

Disabled

Disabled

• Typematic Rate (Chars / Sec.)

The default value is 6.

6-30 Set the maximum Typematic rate from 6 chars. Per second

to 30 characters. Per second.

• Typematic Delay (Msec.)

The default value is 250.

250-1000 Set the time delay from first key to repeat the same key in

to computer.

• Security Option

This category allows you to limit access to the system and Setup, or just to
Setup. The default value is Setup.

System The system can not boot and can not access to Setup page

will be denied if the correct password is not entered at the
prompt

Setup The system will boot, but access to Setup will be denied if

the correct password is not entered at the prompt

• PCI/VGA Palette Snoop

The default value is Disabled.

Enabled For having Video Card on ISA Bus and VGA Card on PCI Bus.

For VGA Card only.

• Assign IRQ For VGA

The default value is Enabled.

Enabled Assign IRQ For VGA

Not assign IRQ For VGA

• OS Select For DRAM>64MB

The default value is Non-OS2.

Non-OS2 Using non-OS2 operating system.
OS2 Using OS2 operating system and DRAM>64MB.

4-12

•

Disabled

HDD S.M.A.R.T. Capability

The default value is Disable.

Enable Enable HDD S.M.A.R.T. Capability
Disable Disable HDD S.M.A.R.T. Capability

• Report No FDD For WIN 95

The default value is No.

No Assign IRQ6 For FDD.
Yes FDD Detect IRQ6 Automatically.

• Video BIOS Shadow

The default value is Enabled.

Enabled Video shadow is enabled

Video shadow is disabled

4.7. CHIPSET FEATURES SETUP

BIOS Configuration

Figure 4.4: Chipset Features Setup

4-13

6BMM

• EDO CASx# MA Wait State

The default value is 1

1 Set EDO CASx# MA Wait State to 1.
2 Set EDO CASx# MA Wait State to 2.

• EDO RASx# Wait State

The default value is 1

1 Set EDO RASx# Wait State to 1.
2 Set EDO RASx# Wait State to 2.

• SDRAM CAS latency Time

The default value is Auto

3 For 67 / 83 MHz SDRAM DIMM module.
2 For 100 MHz SDRAM DIMM module.

Auto CAS latency time will be set automatically if you have SPD

on SDRAM

• DRAM Data Integrity Mode

This value is Non-ECC

Non-ECC For 64bit standard type DIMM module.
ECC For 72bit ECC type DIMM module.

• System BIOS Cacheable

The default value is Enabled.

Enabled Enable System BIOS Cacheable.

Disabled Disable System BIOS Cacheable.

• Video BIOS Cacheable

The default value is Enabled.

Enabled Enable video BIOS Cacheable.

Disabled Disable video BIOS Cacheable.

4-14

BIOS Configuration

• Video RAM Cacheable

The default value is Disabled.

Disabled Disable this function.

Enabled Enable this function to get better VGA performance; while

some brands of VGA must be disabled this function

(e.g.ET4000W32P).

• 16 Bit I/O Recovery Time

The default value is 1.

1-4 Set 16 Bit I/O recovery time from 1 to 4.
NA None.

• Memory Hole At 15M-16M

The default value is Disabled.

Disabled Normal Setting.
Enabled Set Address=15~16MB remap to ISA BUS.

• Delayed Transaction

The default value is Disabled.

Disabled Normal operation.

Enabled For slow speed ISA device in system.

• Spread Spectrum

The default value is Disabled.

Disabled Disabled this function
Enabled Enabled Spread Spectrum

• Slow Down CPU Duty Cycle

The default value is Normal.

Normal Normal Operation

12.5%~75.0% Monitor CPU Temp. will cause system slow down
CPU Duty Cycle to 12.5%~75.0%.

4-15

6BMM

• Shutdown Temp. (°C / °F)

(This function will be effective only for the operating systems that support

ACPI Function.)
The default value is 75°C / 167°F

Disabled Normal Operation

60°C / 140°F Monitor CPU Temp. at 60°C / 140°F, if Temp. > 60°C /

140°F system will automatically power off .

65°C / 149°F Monitor CPU Temp. at 65°C / 149°F, if Temp. > 65°C /

149°F system will automatically power off .

70°C / 158°F Monitor CPU Temp. at 70°C / 158°F, if Temp. > 70°C /

158°F system will automatically power off .

75°C / 167°F Monitor CPU Temp. at 75°C / 167°F, if Temp. > 75°C /

167°F system will automatically power off .

• Temp. Select (°C / °F)

The default value is 70°C /158°F

60°C / 140°F Monitor CPU Temp. at 60°C / 140°F
65°C / 149°F Monitor CPU Temp. at 65°C / 149°F
70°C / 158°F Monitor CPU Temp. at 70°C / 158°F
75°C / 167°F Monitor CPU Temp. at 75°C / 167°F

• Temperature Alarm

The default value is No

No When CPU Temp. overheat, then system won’ t alarm.

Yes When CPU Temp. overheat, then system will alarm.

• Fan Fail Alarm

CPU/POWER/PANEL(SYSTEM)

No Fan Fail Alarm Function Disabled.

Yes Fan Fail Alarm Function Enabled.

4-16

BIOS Configuration

• Reset Case Open Status

• Case Opened

If the case is closed, “Case Opened” will show “No”.
If the case have been opened, “Case Opened” will show “Yes” .
If you want to reset “Case Opened” value, set “Reset Case Open Status”
to “Yes” and save CMOS, your computer will restart.

• Current Temp. (°C / °F)

Detect Temp. automatically.

• Current FAN Speed (RPM)

Detect Fan speed status automatically.

• Current Voltage (V) VCORE / VGTL/ VCC3 / ±12V / ±5V /VBAT /5VSB

Detect system’ s voltage status automatically.

4-17

6BMM

Disabled

V/H SYNC+Blank

4.8. POWER MANAGEMENT SETUP

Figure 4.5: Power Management Setup

\ These two items will show up when “Resume by Alarm” is enabled.

• Power Management

The default value is Enabled.

Enabled Enable Green function.

Disable Green function.

• PM Control by APM

The default value is Yes.

Yes Enable software APM function.
No Disable software APM function.

• Video off Method

The default value is DPMS.

BIOS will turn off V/H-SYNC when gets into Green
mode for Green monitor power saving.

Blank Screen BIOS will only black monitor when gets into Green
DPMS BIOS will use DPMS Standard to control VGA card.

mode.
(The Green type VGA card will turn off V/H-SYNC

automatically.)

4-18

• Suspend Mode

1 min - 1 Hour

1-15 mins.

Delay 4 Sec.

The default value is Disable.

Disabled Disable Suspend Mode.

Setup the timer to enter Suspend Mode.

• HDD Power Down

The default value is Disable.

Disable Disable HDD Power Down mode function.

Enable HDD Power Down mode between 1 to 15 mins.

• VGA Active Monitor

The default value is Disabled.

Disabled Disable monitor VGA activity.
Enabled Enable monitor VGA activity.

• Soft-off by PWR-BTTN

The default value is Instant-off.

Instant-off Soft switch ON/OFF for POWER ON/OFF

Soft switch ON 4sec. for POWER OFF.

• System After AC Back

BIOS Configuration

The default value is Soft-Off.

Memory This function depends on computer status
Soft-Off Set System Soft-Off Status.
Full-On Set System Full-On Status.

• CPUFAN Off In Suspend

The default value is Enabled.

Disabled Disable this function.
Enabled Stop CPU FAN when entering Suspend mode.

4-19

6BMM

• PME Event Wakeup

The default value is Disabled.

Disabled Disable PME Event Wakeup.
Enabled Enable PME Event Wakeup.

• ModemRingOn / WakeOnLan

The default value is Enabled.

Disabled Disable these functions.
Enabled Enable these functions.

• Resume by Alarm

The default value is Disabled.

Disabled Disable this function.
Enabled Enable alarm function to POWER ON system.

If the default value is Enabled.

Date ( of Month) Alarm : 0~31
Time ( hh: mm: ss) Alarm : (0~23) : (0~59) : (0~59)

• IRQ [3-7,9-15], NMI

The default value is Enabled.

Disabled Disable this function.
Enabled Enable monitor IRQ [3-7,9-15] for Green event.

• Primary IDE 0 / 1

The default value is Disabled.

Disabled Disable this function.
Enabled Enable monitor Primary IDE 0 / 1 for Green event.

• Secondary IDE 0 / 1

The default value is Disabled.

Disabled Disable this function.
Enabled Enable monitor Secondary IDE 0 / 1 for Green event.

4-20

• Floppy Disk

The default value is Enabled.

Disabled Disable this function.
Enabled Enable monitor Floppy Disk for Green event.

• Serial Port

The default value is Enabled.

Disabled Disable this function.
Enabled Enable monitor Serial Port for Green event.

• Parallel Port

The default value is Disabled.

Disabled Disable this function.
Enabled Enable monitor Parallel Port for Green event.

4.9. PNP/PCI CONFIGURATION

BIOS Configuration

Figure 4.6: PCI Slot Configuration

\ This item will show up when “Used MEM base addr” has been set.

4-21

6BMM

• PNP OS Installed

The default value is No.

Yes Enable PNP OS Installed function.
No Disable PNP OS Installed function.

• Resources Controlled by

The default value is Manual.

Manual User can set the PnP resource (I/O Address, IRQ & DMA

channels) used by legacy ISA DEVICE.

Auto BIOS automatically use these PnP rescuers.

• Reset Configuration Data

The default value is Disabled.

Disabled Disable this function.
Enabled Enable clear PnP information in ESCD.

• IRQ (7,12,14,15) & IRQ (3,4,5,9,10,11,DMA(0,1,3,5,6,7) assigned to

The default value is "Legacy ISA" or "PCI/ISA PnP".

Legacy ISA The resource is used by Legacy ISA device.
PCI/ISA PnP The resource is used by PCI/ISA PnP device (PCI or

ISA).

• Used MEM base addr

The default value is N/A.

N/A Disable the MEM. block using.

C800 ~ DC00 Select the MEM. block starting address.

• Used MEM Length

The default value is 8K.

8K ~ 64K Select the MEM. block size.

4-22

• Assign IRQ For USB

The default value is Enabled.

Enabled Assign a specific IRQ for USB

Disabled No IRQ is assigned for USB

4.10. LOAD BIOS DEFAULTS

BIOS Configuration

Figure 4.7: Load Bios Defaults

• Load BIOS Defaults

To load BIOS defaults value to CMOS SRAM, enter "Y". If not, enter "N".

4-23

6BMM

4.11. LOAD PERFORMANCE DEFAULTS

Figure 4.8: Load Performance Defaults

• Load Performance Defaults

To load Performance defaults value to CMOS SRAM, enter "Y". If not, enter
"N".

4-24

BIOS Configuration

4.12. INTEGRATED PERIPHERALS

Figure 4.9: Integrated Peripherals

\ This item will show up when “Keyboard Power On: Multikey” is selected.

• IDE HDD Block Mode

The default value is Enabled.

Enabled Enable IDE HDD Block Mode
Disabled Disable IDE HDD Block Mode

• IDE Primary Master PIO (for onboard IDE 1st channel).

The default value is Auto.

Auto BIOS will automatically detect the IDE HDD Accessing

mode.

Mode0~4 Manually set the IDE Accessing mode.

4-25

6BMM

• IDE Primary Slave PIO (for onboard IDE 1st channel).

The default value is Auto.

Auto BIOS will automatically detect the IDE HDD Accessing

mode.

Mode0~4 Manually set the IDE Accessing mode.

• IDE Secondary Master PIO (for onboard IDE 2nd channel).

The default value is Auto.

Auto BIOS will automatically detect the IDE HDD Accessing

mode.

Mode0~4 Manually set the IDE Accessing mode.

• IDE Secondary Slave PIO (for onboard IDE 2nd channel).

The default value is Auto.

Auto BIOS will automatically detect the IDE HDD Accessing

mode.

Mode0~4 Manually set the IDE Accessing mode.

• IDE Primary Master UDMA.

The default value is Auto.

Auto BIOS will automatically detect the IDE HDD Accessing

mode.

Disabled Disable UDMA function.

• IDE Primary Slave UDMA.

The default value is Auto.

Auto BIOS will automatically detect the IDE HDD Accessing

mode.

Disabled Disable UDMA function.

4-26

• IDE Secondary Master UDMA.

The default value is Auto.

Auto BIOS will automatically detect the IDE HDD Accessing

mode.

Disabled Disable UDMA function.

• IDE Secondary Slave UDMA.

The default value is Auto.

Auto BIOS will automatically detect the IDE HDD Accessing

mode.

Disabled Disable UDMA function.

• On-Chip Primary PCI IDE

The default value is Enabled.

Enabled Enable onboard 1st channel IDE port.
Disabled Disable onboard 1st channel IDE port.

• On-Chip Secondary PCI IDE

BIOS Configuration

The default value is Enabled.

Enabled Enable onboard 2nd channel IDE port.
Disabled Disable onboard 2nd channel IDE port.

• USB Keyboard Support

The default value is Disabled.

Enabled Enable USB Keyboard Support.
Disabled Disable USB Keyboard Support.

4-27

6BMM

• Onboard FDD Controller

The default value is Enabled.

Enabled Enable onboard FDD port.
Disabled Disable onboard FDD port.

• Onboard Serial Port 1

The default value is 3F8/IRQ4.

Auto BIOS will automatically setup the port 1 address.
3F8/IRQ4 Enable onboard Serial port 1 and address is 3F8.
2F8/IRQ3 Enable onboard Serial port 1 and address is 2F8.
3E8/IRQ4 Enable onboard Serial port 1 and address is 3E8.
2E8/IRQ3 Enable onboard Serial port 1 and address is 2E8.
Disabled Disable onboard Serial port 1.

• Onboard Serial Port 2

The default value is 2F8/IRQ3.

Auto BIOS will automatically setup the port 2 address.
3F8/IRQ4 Enable onboard Serial port 2 and address is 3F8.
2F8/IRQ3 Enable onboard Serial port 2 and address is 2F8.
3E8/IRQ4 Enable onboard Serial port 2 and address is 3E8.
2E8/IRQ3 Enable onboard Serial port 2 and address is 2E8.
Disabled Disable onboard Serial port 2.

4-28

• Onboard Parallel port

POWER Key

The default value is 378/IRQ7.

378/IRQ7 Enable onboard LPT port and address is 378/IRQ7.
278/IRQ5 Enable onboard LPT port and address is 278/IRQ5.
Disabled Disable onboard LPT port.
3BC/IRQ7 Enable onboard LPT port and address is 3BC/IRQ7.

• Parallel Port Mode

The default value is SPP.

SPP Using Parallel port as Standard Printer Port.
EPP Using Parallel port as Enhanced Parallel Port.
ECP Using Parallel port as Extended Capabilities Port.
ECP/EPP Using Parallel port as ECP & EPP mode.

• PS/2 Mouse Power on

The default value is Disabled.

Disabled Disable PS/2 Mouse Power on .
Left Double Double click twice on PS/2 left bottom.
Right Double Double click twice on PS/2 right bottom.

• Keyboard Power on

BIOS Configuration

The default value is POWER Key.

If your keyboard have “POWER Key” button, you can

press the key to power on your system.
Disabled Disable Keyboard Power on .
Multikey Enter multikey combination to Power on system.

•

KB Power ON Multikey

Enter

Enter from 1 to 5 characters to set the Keyboard Power
On Password.

M You can power on your system by entering the keyboard

power on password.

4-29

6BMM

4.13. SUPERVISOR / USER PASSWORD

When you select this function, the following message will appear at the center
of the screen to assist you in creating a password.

Figure 4.10: Password Setting

Type the password, up to eight characters, and press <Enter>. The password
typed now will clear the previously entered password from CMOS memory. You
will be asked to confirm the password. Type the password again and press
<Enter>. You may also press <Esc> to abort the selection and not enter a
password.

To disable password, just press <Enter> when you are prompted to enter
password. A message “PASSWORD DISABLED” will appear to confirm the
password being disabled. Once the password is disabled, the system will boot
and you can enter Setup freely.

If you select System at Security Option in BIOS Features Setup Menu, you will
be prompted for the password every time the system is rebooted or any time
you try to enter Setup Menu. If you select Setup at Security Option in BIOS
Features Setup Menu, you will be prompted only when you try to enter Setup.

4-30

BIOS Configuration

4.14. IDE HDD AUTO DETECTION

Figure 4.11: IDE HDD Auto Detection

Type "Y" will accept the H.D.D. parameter reported by BIOS.

Type "N" will keep the old H.D.D. parameter setup. If the hard disk cylinder
number is over 1024, then the user can select LBA mode or LARGER mode for
DOS partition larger than 528 MB.

4-31

6BMM

4.15. SAVE & EXIT SETUP

Figure 4.12: Save & Exit Setup

Type "Y" will quit the Setup Utility and save the user setup value to RTC CMOS
SRAM.

Type "N" will return to Setup Utility.

4-32

BIOS Configuration

4.16. EXIT WITHOUT SAVING

Figure 4.13: Exit Without Saving

Type "Y" will quit the Setup Utility without saving to RTC CMOS SRAM.

Type "N" will return to Setup Utility.

4-33

On-Board Display & Sound Driver Installation

“Cancel”

APPENDIX A: On-Board Display & Sound Driver Installation

A.1. ATI Rage Pro display driver installation:

When loading the ATi drivers for the system, the Windows version should be
OSR 2.1 or later or Windows 98 Bata3 or later.

If your system version is Win95 or OSR 2.0, You must use the USB support
update (make sure the update language is the same with your system
language) to upgrade your system to OSR 2.1.

M You can found the USB support update in the April 1997 MSDN

Disc1\OSR2\USBSUPP.

A.1.1 Windows 95 OSR 2.1 or Win98 Driver Installation

Install the Windows 95 or Win98 driver is very easy. When you insert the CD
disc into your CD-ROM, you can see the AUTORUN window (If it does not
show up, run “D:\Atisetup.exe”. This manual assumes that your CD-ROM
device drive letter is D:). Then you can follow it to setup you ATI driver or
follow the “Step By Step Installation” to install the driver.

Step By Step Installation
Step 1:

Press the
“Next” button.

A-1

Don’ t press
because the system will
hang if you press it.

,

6BMM

Step 2:

Press the

“Finish”

button

At this time, system will ask for your Windows CD disk in order to complete the
VGA driver installation.

If you don’ t have the CD disk, you can press C:\Windows\System directory.

Step 3:

Select the
“NO” button

A-2

On-Board Display & Sound Driver Installation

“Easy Install ”

“Next ”

After the system finishes loading. You must insert the ATI Installation CD disk
into your CD-ROM, then you can see the AUTORUN window. If it does not
show up, please run “D:\Atisetup.exe”

STEP 4:

STEP 5:

Select the

Click the

A-3

item.

item.

6BMM

“Next ”

“Finish ”

STEP 6:

Click the

STEP 7:

Click the

STEP 8:

Windows 95/98 will restart and start up using the ATI driver.

A-4

item.

item.

On-Board Display & Sound Driver Installation

A.1.2 Windows NT 4.0 Driver Installation

Please make sure the Windows NT 4.0 have installed Windows NT 4.0
Service Pack version 3.0, before installing the ATi RAGE PRO driver.

1. Boot Windows NT, then select “Windows NT Workstation Version 4.00
[VGA mode]”.

2. When NT finishes loading, press your mouse right button in Windows NT

wallpaper area.

3. Then select the “Properties” item.

4. Select the “Settings” Item.

5. Select the “Display Type” button, and press the “Change” button.

6. Click on “Have Disk” and insert the ATi Driver CD disk in your CD-ROM.

7. Type in D:\WINNT (if your CD in Driver D:), and click “OK”.

8. A list of ATi graphics accelerators will be displayed. Select the one “ATI
Technologies Inc. 3D RAGE PRO TURBO” ,then click the “OK” button.

9. Windows NT 4.0 will once again prompt for confirmation. All appropriate files

are then copied to the hard disk.

10. Restart Windows NT 4.0 Windows NT 4.0 will start up using the ATI

driver.

11. NT 4.0 will boot into a default mode and start the Display applet allowing

for mode selection.

A-5

6BMM

A.2. YAMAHA PCI sound driver installation:

A.2.1 Windows 95 &98 Driver Installation
This manual assumes that your CD-ROM device drive letter is D:).

When starting Windows 95/98, the operation system will detect that you
have a new PCI Multimedia Device, and the Update Device Driver
Wizard will show up.

Click the
“Next” button.

A-6

Click the
“Finish” button.

On-Board Display & Sound Driver Installation

item.

After the system finishes loading. You must insert the YAMAHA Installation CD
disk into your CD-ROM, then you can see the AUTORUN window. If it does not
show up, please run “D:\YAMAHA\Win95_98\install.exe”

STEP 1:

Select the
“YAMAHA Sound

Driver Setup”

STEP 2:

Select the
“For Win95/98”
item.

A-7

6BMM

STEP 3:

STEP 4:

Click the
“Next” button.

A-8

Click the
“Finish” button.

On-Board Display & Sound Driver Installation

item.

A.2.2 Windows 95/98 DOS Mode Driver Installation

STEP 1:

STEP 2:

Select the
“YAMAHA Sound

Driver Setup”

A-9

Select the
“For Win95/98
DOS Mode” item.

6BMM

STEP 3:

STEP 4:

Click the
“Next” button.

Click the
“Next” button to
accept the default
directory or click the
“Browse” button to
choose directory.

A-10

STEP 5:

STEP 6:

On-Board Display & Sound Driver Installation

Click the
“Next” button.

A-11

Click the
“OK” button.

6BMM

STEP 7:

STEP 8:

Click the
“Next” button.

A-12

Click the
“OK” button.

STEP 9:

STEP 10:

On-Board Display & Sound Driver Installation

Click the
“Next” button.

Click the
“OK” button.

A-13

6BMM

A.2.3 Windows NT 4.0 Driver Installation

1. Boot Windows NT, then select “Windows NT Workstation Version 4.00

[VGA mode]”.

2. When NT finishes loading, open the “Control Panel” in Windows NT “My

Computer” area.

3. Select the “Multimedia” Item.

4. Select the “Devices” button, then press the “Add” button.

5. Select the “Unlisted or Updated Driver”, then press the “OK” button.

6. Type in D:\YAMAHA\WINNT (if your CD in Driver D:), and click “OK”.

7. A list of YAMAHA audio drivers will be displayed. Select the one that

supports your operation system language, then click the “OK” button.

8. Restart Windows NT 4.0. Windows NT 4.0 will start up using the audio

driver.

A-14

On-Board Display & Sound Driver Installation

A.2.4 DOS Driver Installation

1. Insert the Drivers Disc into the CD-ROM Drive (For example D:).

2. In real DOS mode, please type D:\YAMAHA\dos6x\install.exe

3. Choose “Yes” when the message “Do you want to install the DS-XG

Board?” appears.

4. When the message “Configuration file will be installed to: C:\DS-SG

“appears, Press “Enter” to accept the default directory or create a
directory that you want the driver to be installed.

5. Press “Enter” to accept the backup file of autoexec.bat to be created.

6. If the file “autoexec.bak “ exists, the system will ask whether you want to

replace it or not. Choose "yes" to replace the old autoexec.bak.

7. You can just press “Enter” for the system to go through the installation

process. When the installation is completed, you have to restart the
computer for the changes to effect.

8. When you have restarted the computer, the configuration program

“setupds” will be loaded automatically. You can choose the configuration
that you want or just accept the default settings. Remember to save the
settings by pressing "ESC" and choose "Save and Exit" option.

A-15

DECLARATION OF CONFORMITY

Per FCC Part 2 Section 2. 1077(a)

FCC Compliance Statement:

This equipment has been tested and found to

Responsible Party Name: G.B.T. INC.

Address: 18305 Valley Blvd., Suite#A

LA Puent, CA 91744

Phone/Fax No: [phone]/ [phone]

hereby declares that the product

Product Name:

Mother Board

GA-6BMM

Model Number:

Conforms to the following specifications:

FCC Part 15, Subpart B, Section 15.107(a) and Section 15.109(a),
Class B Digital Device

Supplementary Information:

This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any inference received, including interference
that may cause undesired operation.

Representative Person's Name: ERIC LU

Signature:

Date: Jan 15, 1999

Eric Lu

comply with limits for a Class B digital device ,
pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable
protection against harmful interference in
residential installations. This equipment
generates, uses, and can radiate radio
frequency energy, and if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular

installation. If this equipment does cause
interference to radio or television equipment reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna

-Move the equipment away from the receiver

-Plug the equipment into an outlet on a circuit different from that to which
the receiver is connected

-Consult the dealer or an experienced radio/television technician for
additional suggestions

You are cautioned that any change or modifications to the equipment not
expressly approve by the party responsible for compliance could void Your
authority to operate such equipment.

This device complies with Part 15 of the FCC Rules. Operation is subjected to
the following two conditions 1) this device may not cause harmful interference
and 2) this device must accept any interference received, including interference
that may cause undesired operation.

Declaration of Conformity

We, Manufacturer/Importer

(full address)

G.B.T. Technology Träding GMbH

Ausschlager Weg 41, 1F, 20537 Hamburg, Germany

( description of the apparatus, system, installation to which it refers)

(reference to the specification under which conformity is declared)

EN 55011 Limits and methods of measurement EN 61000-3-2* Disturbances in supply systems caused

of radio disturbance characteristics of EN60555-2 by household appliances and similar
industrial, scientific and medical (ISM electrical equipment “Harmonics”
high frequency equipment

EN55013 Limits and methods of measurement EN61000-3-3* Disturbances in supply systems caused

EN 55014 Limits and methods of measurement EN 50081-1 Generic emission standard Part 1:

EN 55015 Limits and methods of measurement EN 55081-2 Generic emission standard Part 2:

EN 55020 Immunity from radio interference of EN 55082-2 Generic immunity standard Part 2:

EN 55022 Limits and methods of measurement ENV 55104 Immunity requirements for household

DIN VDE 0855 Cabled distribution systems; Equipment EN 50091- 2 EMC requirements for uninterruptible
part 10 for receiving and/or distribution from power systems (UPS)
part 12 sound and television signals

of radio disturbance characteristics of EN60555-3 by household appliances and similar
broadcast receivers and associated electrical equipment “Voltage fluctuations”
equipment

of radio disturbance characteristics of Residual, commercial and light industry
household electrical appliances,
portable tools and similar electrical EN 50082-1 Generic immunity standard Part 1:
apparatus Residual, commercial and light industry

of radio disturbance characteristics of Industrial environment
fluorescent lamps and luminaries

broadcast receivers and associated Industrial environment
equipment

of radio disturbance characteristics of appliances tools and similar apparatus
information technology equipment

declare that the product

Mother Board

GA-6BMM

is in conformity with

in accordance with 89/336 EEC-EMC Directive

CE marking (EC conformity marking)

The manufacturer also declares the conformity of above mentioned product
with the actual required safety standards in accordance with LVD 73/23 EEC

EN 60065 Safety requirements for mains operated EN 60950 Safety for information technology equipment

EN 60335 Safety of household and similar EN 50091-1 General and Safety requirements for

electronic and related apparatus for including electrical business equipment
household and similar general use

electrical appliances uninterruptible power systems (UPS)

Manufacturer/Importer

Date : JAN. 15, 1999 Name : Rex Lin

(Stamp)

Signature

Rex Lin

: