Gigabyte GA-686LX2 GA-686LX2 - User Manual (Rev 1.1)

Table of Table

TABLE OF CONTENTS

1. INTRODUCTION................................................................................1-1

1.1. PREFACE..........................................................................................................1-1

1.2. KEY FEATURES...............................................................................................1-1

1.3. PERFORMANCE LIST......................................................................................1-2

1.4. BLOCK DIAGRAM ............................................................................................1-3

1.5. INTRODUCE THE Pentium II Processor.......................................................1-4

1.6. WHAT IS AGP? .................................................. 1-6

2. SPECIFICATION ...............................................................................2-1

2.1. HARDWARE.....................................................................................................2-1

2.2. SOFTWARE......................................................................................................2-2

2.3. ENVIRONMENT................................................................................................2-2

3. HARDWARE INSTALLATION............................................................3-1

3.1. UNPACKING.....................................................................................................3-1

3.2. MAINBOARD LAYOUT.....................................................................................3-2

3.3. QUICK REFERENCE FOR JUMPERS & CONNECTORS .............................3-2

3.4. DRAM INSTALLATION.....................................................................................3-6

3.5. CPU SPEED SETUP ........................................................................................3-6

3.6. CMOS RTC & ISA CFG CMOS SRAM.............................................................3-7

3.7. SPEAKER CONNECTOR INSTALLATION .....................................................3-7

3.8. HARDWARE RESET SWITCH CONNECTOR INSTALLATION....................3-7

3.9. POWER LED CONNECTOR INSTALLATION ................................................3-7

3.10. IDE & ATAPI DEVICE INSTALLATION..........................................................3-7

1

686LX2

3.12. PERIPHERAL DEVICE INSTALLATION........................................................3-8

3.13. KEYBOARD & PS/2 MOUSE INSTALLATION..............................................3-8

3.14. KEYBOARD SETTING FUNCTION ...............................................................3-8

4. BIOS CONFIGURATION ...................................................................4-1

4.1. ENTERING SETUP ..........................................................................................4-1

4.2. CONTROL KEYS..............................................................................................4-1

4.3. GETTING HELP................................................................................................4-2

4.3.1. Main Menu ................................................ 4-2

4.3.2. Status Page Setup Menu / Option Page Setup Menu.............. 4-2

4.4. THE MAIN MENU..............................................................................................4-2

4.5. STANDARD CMOS SETUP MENU .................................................................4-4

4.6. BIOS FEATURES SETUP................................................................................4-8

4.7. CHIPSET FEATURES SETUP.........................................................................4-12

4.8. POWER MANAGEMENT SETUP....................................................................4-17

4.9. PNP/PCI CONFIGURATION............................................................................4-20

4.10. INTEGRATED PERIPHERALS ......................................................................4-22

4.11. LOAD SETUP DEFAULTS .............................................................................4-26

4.12. USER PASSWORD .......................................................................................4-27

4.13. IDE HDD AUTO DETECTION........................................................................4-28

4.14. SAVE & EXIT SETUP.....................................................................................4-29

4.15. EXIT WITHOUT SAVING...............................................................................4-30

2

Introduction

1. INTRODUCTION

1.1. PREFACE

Welcome to use the 686LX2 motherboard. The motherboard is a Dual
Pentium II Processor based PC / AT compatible system with AGP / PCI /

ISA Bus, and has been designed to be the fastest PC / AT system. There are
some new features allow you to operate the system with just the performance
you want.

This manual also explains how to install the motherboard for operation, and
how to set up your CMOS CONFIGURATION with BIOS SETUP program.

1.2. KEY FEATURES

q Intel Dual Pentium
q Dual Slot 1 on board supports dual Pentium



II Processor based PC / AT compatible mainboard.



II processor running at 200-

633MHz.

q Intel 440LX chipset, Support AGP / SDRAM / Ultra DMA/33 IDE / ACPI

features.

q Support CPU FAN Failure / Overheat Alarm & auto slow down CPU

speed.

q Support PS/2 mouse & Keyboard Wake Up function.
q Support Intel LDCM
q Support PCI Audio & Wake on Lan function.
q Supports 4xDIMMs using 3.3V EDO or SDRAM DIMM module.
q Supports 8 MB - 1 GB EDO / 512MB SDRAM memory on board.
q Supports ECC or Non-ECC type DRAM module.
q 1xAGP slot, 5xPCI Bus slots, 2xISA Bus slots.
q Supports 2 channels Ultra DMA/33 IDE ports for 4 IDE Device.
q Supports 2xCOM (16550), 1xLPT (EPP / ECP), 1x1.44MB Floppy port.
q Supports 2xUSB ports, 1xPS/2 Mouse & 1xPS/2 Keyboard ports.
q Licensed AWARD BIOS, 2M bit FLASH RAM.



Network Manageability.

1-1

686LX2

q ATX form factor, Double stack I/O connector, 4 layers PCB.

1.3. PERFORMANCE LIST

The following performance data list is the testing results of some popular
benchmark testing programs.

These data are just referred by users, and there is no responsibility for
different testing data values gotten by users. (The different Hardware &
Software configuration will result in different benchmark testing results.)

• CPU

Pentium II processor

• DRAM 64 MB SDRAM

• CACHE SIZE 512 KB included in CPU

• DISPLAY Matrox Millennium II 4MB PCI VGA

• STORAGE Onboard IDE port

• O.S. Windows95 OSR2.0.

• DRIVER Display Driver at 1024 x 768 x 64K colors x 75Hz.

Triones Bus Master IDE Driver 3.60K

Processor

Intel Pentium II

266MHz 300MHz

Winbench97

CPU mark32

Business Disk

Hi-End Disk

Business Graphic

Hi-End Graphic

695 781

2230 2234

6110 6260

129 140

55.4 61.2

Winstone 97

Business

Hi-End

62.8 65.2

31.1 33.2

1-2

Introduction

1.4. BLOCK DIAGRAM

SLOT 1

AGP

SLOT

14.318MHz

33MHz

CLOCK
GEN
52C64-06

Host Bus

AGP Bus

33MHz

14.318MHz
33MHz
48MHz

PAC

82443LX

CHIPSET

PCI Bus

PCI Bus

PIIX4

82371AB

CHIPSET

14.318MHz

USB Bus

SLOT2

DRAM Bus

66MHz
66MHz

USB #1

3.3VEDO/SDRAM
DIMM Sockets

CLOCK

66MHz

GEN
52C64-25

66MHz

APIC

USB #2

I/O

IDE Bus

14.318MHz

14.318MHz

8MHz

ISA Bus

24MHz

83977TF

1-3

COM Ports

LPT Port

I/O

Floppy Port

PS/2 Keyboard

PS/2 Mouse

32.768KHz

686LX2

1.5. INTRODUCE THE Pentium II Processor

Figure 1:Retention Mechanism & attach Mount

Figure 2:OEM Pentium II Processor

1-4

Introduction

Figure 3:Heatsink / FAN & Heat sink support for OEM Pentium II Processor

Figure 4:Boxed Pentium II Processor & Heat sink support

1-5

686LX2

1.6. WHAT IS AGP

?

The Accelerated Graphics Port (AGP) is a new port on the Host-To-PCI
bridge device that supports an AGP port. The main purpose of the AGP port
is to provide fast access to system memory.

The AGP port can be used either as fast PCI port (32-bits at 66MHz vs. 32­bits at 33MHz) or as an AGP port which supports 2x data-rate, a read queue,
and side band addressing. When the 2x-data rate is used the port can
transmit data at 533Mb/sec (66.6*2*4). The read-queue can be used to
pipeline reads – removing the effects of the reads-latency. Side band
addressing can be used to transmit the data address on a separate line in
order to further speed the transaction.

.

1-6

2. SPECIFICATION

2.1. HARDWARE

Specification

• CPU

• PROTECTION

• SPEED

• DRAM MEMORY

• CACHE MEMORY

• I/O BUS SLOTS

• IDE PORTS

− Dual Pentium

− Dual 242 pins 66MHz slot1 on board.

− PC Speaker Alarm when detect "CPU FAN Failure"



II processor 200 – 633 MHz.

or “CPU Overheat”.

− Automatically slow down CPU speed when "CPU

FAN Failure" or "CPU Overheat".

− Intel LDCM

− H/W monitor power status (±5V, ±12V, CPU



support.

voltage & CMOS battery voltage).

− 66 MHz system speed.

− 66 MHz AGP bus speed. (133MHz 2*mode)

− 33 MHz PCI-Bus speed.

− 8 MHz AT bus speed.

− 4 banks 168 pins DIMM module sockets on board.

− Use 8 / 16 / 32 / 64 / 128 / 256 MB 60~70 ns DIMM

module DRAM.

− 8 M ~ 1 GB DRAM size.

− Support 3.3V SDRAM / EDO type DRAM.

− Support ECC or Non-ECC type DRAM.

− 32 KB 1st cache memory included in CPU.

− 256KB/512 KB 2nd cache in CPU.

− Support DIB speed mode for L2 Cache.

− 1 66 / 133MHz AGP BUS.

− 5 33MHz Master / Slave PCI-BUS.

− 2 8MHz 16 bits ISA BUS.

− 2 Ultra DMA/33 Bus Master IDE channels on

board.(Using IRQ14,15)

− Backward Support Mode 3,4 IDE & ATAPI CD -

ROM.

2-1

686LX2

• I/O PORTS

− Supports 2 16550 COM ports. (Using IRQ4, 3)

− Supports 1 EPP/ECP LPT port. (Using IRQ7 or 5

and DMA3 or 1)

− Supports 1 1.44/2.88 MB Floppy port. (Using DMA2

& IRQ6)

− Supports 2 USB ports.

− Supports PS/2 Mouse. (Using IRQ12 )

− Supports PS/2 Keyboard. (Using IRQ1 )

• GREEN FUNCTION

• BIOS

• DIMENSION

− Suspend mode support.

− Green switch & ACPI LED support..

− IDE & Display power down support.

− Monitor all IRQ / DMA / Display / I/O events.

− 2M Bit FLASH EEPROM.

− Supports Plug & Play, DMI, ACPI Function.

− ATX Form Factor, 4 layers PCB.

2.2. SOFTWARE

• DRIVER

− Intel LDCM

− Health monitor Utility.

− Bus Master IDE Driver.

− Suspend to HD utility.



optional.

• BIOS − Licensed AWARD BIOS.

− AT CMOS Setup, BIOS / Chipset Setup, Green

Setup, Hard Disk Utility included.

− Monitor Health status.

• O.S.

− Operation with MS-DOS

WINDOWS NT, OS/2, NOVELL and SCO UNIX.



, Windows95,

2.3. ENVIRONMENT

• Ambient Temp.

− 0°C to +50°C (Operating).

• Relative Hum. − 0 to +85% (Operating).

• Altitude − 0 to 10,000 feet (Operating).

• Vibration − 0 to 1,000 Hz.

• Electricity − 4.9 V to 5.2 V.

− Max. 20A current at 5V.

2-2

Hardware Installation

3. HARDWARE INSTALLATION

3.1. UNPACKING

The mainboard package should contain the following:

• The 686LX2 mainboard.

• The Retention Mechanism & Attach Mount

• USER'S MANUAL for mainboard.

• Cable set for IDE¡BFloppy device.

• Diskette or CD for Mainboard Utility Controller.

The mainboard contains sensitive electric components, which can be easily
damaged by static electricity, so the mainboard should be left in its original
packing until it is installed.

Unpacking and installation should be done on a grounded anti-static mat.
The operator should be wearing an anti static wristband, grounded at the
same point as the anti-static mat.

Inspect the mainboard carton for obvious damage. Shipping and handling
may cause damage to your board. Be sure there are no shipping and
handling damages on the board before proceeding.

After opening the mainboard carton, extract the system board and place it
only on a grounded anti-static surface component side up. Again inspect the
board for damage. Press down on all of the socket IC's to make sure that
they are properly seated. Do this only on with the board placed on a firm flat
surface.

M

DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN DAMAGED.

You are now ready to install your mainboard. The mounting hole pattern on
the mainboard matches the ATX system board. It is assumed that the
chassis is designed for a standard ATX mainboard mounting.

Place the chassis on the anti-static mat and remove the cover. Take the clips,
stand-off and screws for mounting the system board, and keep them

3-1

686LX2

SLOT2

Bank 1

Bank 0

Bank 3

Bank 2

SLOT4

separate.

3.2. MAINBOARD LAYOUT

SLOT2 SLOT1

BAT1

PAC
82443LX
CHIPSET

FAN PWR2

FAN PWR1

JP8

SW

4
3
2
1

REST

JP6

J11

SPK

J10

PWR

J7 J6
HD IR

JP5JP4
GN

SOFT PWR

×Figure 3.1Ø

3.3. QUICK REFERENCE FOR JUMPERS & CONNECTORS

t I/O Ports Connector

CN1 For USB port.
CN2 For Secondary IDE port.
CN3 For Primary IDE port.

J4 For Floppy port.

J3 For PS/2 Mouse & Keyboard I/O ports.
JP2 For Serial port2 (COM B).
JP3 For Serial port1 (COM A).

J5 For LPT port.

t CPU1: slot1

For Pentium II processor installed.

3-2

t CPU2: slot1

For Pentium II processor installed.

t J1: CPU2 cooling FAN Power Connector

Pin No. Function

1 GND.
2 +12V
3 SENSE

t J2: CPU1 cooling FAN Power Connector

Pin No. Function

1 GND.
2 +12V
3 SENSE

t J6: INFRARED Connector (IR) -- Function Option

Pin No. Function

1 IR Data Output
2 GND
3 IR Data Input
4 Signal
5 POWER (+)

Hardware Installation

t J7: Hard Disk active LED (HD-LED)

Pin No. Function

1 LED POWER (+)
2 LED POWER (-)
3 LED POWER (-)
4 LED POWER (+)

t J10: RESET Switch

Pin No. Function

1 RESET Input
2 GND

3-3

686LX2

t J11: SPEAKER Connector

Pin No. Function

1 VCC
2 NC.
3 NC.
4 Output

t J12 : By Pass ATX PWR CTRL

Pin No. Function

1 Signal
2 GND

t JP1 : Keyboard Power On Connector

Pin No. Function
1,2 Close Enabled Keyboard power on.
2,3 Close Disabled Keyboard power on.

t JP4: Soft Power Switch

On – Off for POWER ON or Suspend IN / OUT.
On 4 sec. For POWER OFF before VGA Enable or CMOS setup select
“delay 4sec.” For POWER OFF mode.

t JP5: GN-SW

On – Off for enter suspend Green Mode.

t JP6: POWER ON LED (PW-LED)

Pin No. Function

1 LED POWER (+)
2 NC
3 GND (-)

t JP7 : ACPI LED selection

Pin No. Function

1 Signal
2 GND

3-4

Hardware Installation

t JP8 : For PCI Audio / Sound Card use only

Pin No. Function

1 Signal
2 GND
3 NC
4 Signal
5 GND
6 Signal

t JP9 : Wake on Lan

Pin No. Function

1 +5V SB
2 GND
3 Signal

t S1: CPU INT. / EXT. FREQ. RATIO

CPU TYPE 1 2 3 4 CLK RATIO

200MHz OFF ON OFF OFF X3
233MHz ON ON OFF OFF X3.5
266MHz OFF OFF ON OFF X4
300MHz ON OFF ON OFF X4.5
333MHz OFF ON ON OFF X5
366MHz ON ON ON OFF X5.5

t POWER1: ATX POWER connector

Pin No. Function

3,5,7,13,15-17GND

4,6,19,20 VCC (+5V)

10 +12V
12 -12V
18 -5V

8 Power Good
9 5V SB (Stand by +5V)

14 PS-ON (Soft ON/OFF)

3-5

686LX2

3.4. DRAM INSTALLATION

The mainboard can be installed with 4 / 8 / 16 / 32 / 64 / 128 / 256 MB 168
pins DIMM module DRAM, and the DRAM speed must be 50 or 60 ns for
EDO & 67~100 MHz for SDRAM. The DRAM memory system on mainboard
consists of bank 0, 1, 2 & bank 3.

Because the 168 pins DIMM module is 64 bits width, using 1 PCS which can
match a 64 bits system. The total memory size is 8 MB ~ 1 GB EDO /
512MB SDRAM. The DRAM installation position refer to Figure 3.1, and
notice the Pin 1 of DIMM module must match with the Pin 1 of DIMM socket.
Insert the DRAM DIMM module into the DIMM socket at Vertical angle. If
there is a wrong direction of Pin 1, the DRAM DIMM module couldn't be
inserted into socket completely.

3.5. CPU SPEED SETUP

The system's speed is fixed to 66.6MHz. The user can change the DIP
SWITCH (SW) selection to set up the CPU speed for 200 - 633MHz
processor. The CPU speed must match with the frequency RATIO. It will
cause system hanging up if the frequency RATIO is higher than CPU's.

DIP SWITCH (S1)

1 2 3 4

OFF ON OFF OFF 3 66 200 Pentium II 200 MHz

ON ON OFF OFF 3.5 66 233 Pentium II 233 MHz

OFF OFF ON OFF 4 66 266 Pentium II 266 MHz

ON OFF ON OFF 4.5 66 300 Pentium II 300 MHz

OFF ON ON OFF 5 66 333 Pentium II 333 MHz

ON ON ON OFF 5.5 66 366 Pentium II 366 MHz

M

The CPU is a sensitive electric component and it can be easily

FREQ.

RATIO

EXT.CLK.

MHz

NT.CLK.

MHz

CPU Type

damaged by static electricity, so users must keep it away from

3-6

Hardware Installation

metal surface when the CPU is installed onto mainboard.

3.6. CMOS RTC & ISA CFG CMOS SRAM

There're RTC & CMOS SRAM on board; they have a power supply from
external battery to keep the DATA inviolate & effective. The RTC is a REAL­TIME CLOCK device, which provides the DATE & TIME to system. The
CMOS SRAM is used for keeping the information of system configuration, so
the system can automatically boot OS. every time. Due to the life-time of
Battery internal battery is 5 years, the user can change a new Battery to
replace old one after it can not work.

3.7. SPEAKER CONNECTOR INSTALLATION

There is always a speaker in AT system for sound purpose. The 4 - Pins
connector J11 is used to connect speaker.

The speaker can work well in both direction of connector when it is installed
to the connector J11 on mainboard.

3.8. HARDWARE RESET SWITCH CONNECTOR INSTALLATION

The RESET switch on panel provides users with HARDWARE RESET
function, which is almost the same as power-on/off.

The system will do a cold start after the RESET switch is pushed and
released by user. The RESET switch is a 2 PIN connector and should be
installed to J10 on mainboard.

3.9. POWER LED CONNECTOR INSTALLATION

There are system power LED lamps on the panel of case. The power LED
will light on when system is powered-on, which is connected to a 3 PIN
connector.

The connector should be connected to JP6 of mainboard in correct direction.

3.10. IDE & ATAPI DEVICE INSTALLATION

There are two Enhance PCI IDE ports (CN2,3) on board, which following
ATAPI standard SPEC. Any one IDE port can connected to two ATAPI
devices (IDE Hard Disk, CD-ROM & Tape Driver), so total four ATAPI
devices can exist in a system.

3-7

686LX2

The J7 is the active LED port for ATAPI device.

3.12. PERIPHERAL DEVICE INSTALLATION

After the I/O device installation and jumpers setup, the mainboard can be
mounted into the case and fixed by screw.

To complete the mainboard installation, the peripheral device could be
installed now. The basic system needs a display interface card.

If the PCI - Bus device is to be installed in the system, any one of five PCI ­Bus slots can be used.

3.13. KEYBOARD & PS/2 MOUSE INSTALLATION

The main board supports PS/2 connector type keyboard & Mouse (J3).
The BIOS will auto detect whether the PS/2 Mouse is installed or nor &

assign IRQ12 for Mouse port if which was installed.
After installing the peripheral device, the user should check everything again,

and prepare to power-on the system.

3.14. KEYBOARD SETTING FUNCTION

After booting the O.S., there are some special functions used by keyboard as
follows:

"CTRL_ALT_DEL" − Pressing these keys simultaneously will cause

system to Warm Start (Software Reset).

3-8