GIGABYTE Cyclops Owner's Manual

Installation Guide
Bracket Instruction
GH-UDUE21-FC
Features
1. Support s nVIDIA SLi and ATi CrossFi re.
2. High Per formance – Alumi num n with copper
pillar and ba se to advance thermal c irculation.
3. Radial air ow – 8 cm fan with rad ial airow to
enhance th ermal circulatio n of surrounding compone nts.
4. Light weig ht – Only 200g, VGA car d loading free.
5. Two covers in red a nd green– Users may us e the
cover depen d on their preference.
6. Ball bear ing fan with 2300 r pm – provides quiet
and long life ex pectancy and reli ability.
7. Heat sink for memo ry.
8. Easy and fas t installation.
Accessories
2) Wrench x 1 3) Heat Sink x 8
1) Cover ( red ) x 1
Caution
The follow ing are not covered by the wa rranty :
1. Use the product i ncorrectly or in a m anner other than the des igned
purpose.
2. Nonobserva nce of the proper operat ion provided. (e.g. over-cloc king)
3. Malfunctio n due to interferenc e from other devices .
4. Fail to install due to t he specicatio n of the VGA card or other
compone nts that are not suppor ted by the product.
5. Unauthorize d modication of th e product.
ood).
7. The warranty l abel of the product has b een removed or damaged .
8. Any loss cause d by removing the origin al heat sink on VGA card.
9. Any loss caused by f ailure to follow the inst allation process contained
in the user.
Specication
Heat Sink Dimension : 160 x 91 x 34 mm
Fan Dimension : 80 x 80 x 15 mm
Base material : Copper
Fin material : Aluminum
Rated Voltage : 12 V
Rated Current : 0.19 Amp
Fan Speed : 2300 rpm
Noise : 25 dBA
Bearing Type : EB R Bearing
5) Nut x 4 6) Screw x 4 7) Gr ease x 1
Fan Life Expectancy : 30,000 hr
Support :
nVIDIA 6600 PCI-E series
nVIDIA 7600 PCI-E serie
ATi RADEON X1650 series
ATi RADEON X700 series
ATi RADEON X1600 series
ATi RADEON X1300 series
ATi RADEON X800 series
4) Washer x 4
PCI-E
nVIDIA ATi
GeForce 66 00 LE
GeForce 66 00
GeForce 66 00 GT
GeForce 730 0 GS
GeForce 760 0 GS
GeForce 760 0 GT
TYPE A TYPE B
RADEON X1650 X T
RADEON X1650 Pr o
RADEON X1600 X T
RADEON X1600 P ro
RADEON X1300 Pr o
RADEON X1300
AGP
nVIDIA ATi nVIDIA ATi nVIDIA ATi
Installation Instruction ( ATi and nVIDIA )
STEP 1
Cautio n : Please be careful whi le removing the orig inal heat sink on the VGA ca rd. GIGABYTE
Figure A
STEP 2
memories o n the VGA card, to remove
the sticker o n the back of the heat sinks and past e on the memories.
( as Figure B )
Figure B
To replace the
STEP 4
cover, use the pin cer compress t he collapsible end of the pus h clips to slid e out to remove the origi nal cover and put on th e new one by aligning the push clip s with the lock holes o n the cooler an d pushed completely t hrough
Figure D
the holes to l ock it. ( as Figure D )
STEP 6
with wrenc h. ( as Figure F )
Figure F
STEP 8
nuts on the sc rews with screwdri ver to fasten the c ooler.
(as Figure H)
Figure H
Remove the or iginal cooler on the VG A card and clean the gr ease.
( as Figure A )
Remove heat sin ks on the memories if any.
is not respo nsible to any loss cause d during the removing p rocess.
Accordi ng to the
number of the
Lock the scr ews
on the bracke t
Please lock the screws on the
appropria te positions.
Place the was hers on
the screws and l ock the
To avoi d th e d amag e t o t he ch ip, p lea se l ock t he nu ts diagonally.
PCI-E
RADEON X8 00 XL
RADEON X8 00 GTO
RADEON X8 00
RADEON X8 00 XT
RADEON X8 00 Pro
RADEON X 700 XT
RADEON X 700 Pro
RADEON X 700
STEP 3
the VGA chip ap propriately.
( as Figure C )
Figure C
STEP 5
the coppe r base. ( as Figure E )
Figure E
STEP 7
table and al ign the holes for
the screws o n the VGA card to
the screws o n the cooler.
( as Figure G )
Figure G
STEP 9
connect the p ower cord of the fan to the output o f the power supply.
( as Figure I )
Figure I
AGP
RADEON X8 00 XL
RADEON X8 00
RADEON X8 00 XT
RADEON X8 00 Pro
Apply the
grease on
Tear off the sticker on
Place the
cooler on the
To complete the instal lation,
W hi le in st a ll in g t he pow er cor d o f t he fan , pleas e be carefu l not to interfer e to the blade.
Loading...