GE Security 470610001 Specsheet
Product Data Sheet
Model 1000 and 1010
Dual Technology Readers
Dual Technology Readers
The Dual Technology readers combine the ability to read
ProxLite® , proximity and standard magstripe badges in one
badge reader. There are two models available: Model 1000, a
proximity magstripe reader; and Model 1010, which includes a
12-key tactile keypad. In each case, the one-piece reader
housing is molded from rugged and maintenance-free
polycarbonate. The gray housing blends readily with a wide
range of decors.
Both readers include a functional self-test on power-up and selftuning. As a result, the readers will automatically adjust to local
site conditions that affect reader operation.
The Model 1010 keypad works equally well with either proximity
or magstripe badges. In each case, PIN (Personal Identification
Number) entry follows a valid badge read for two-factor security,
as indicated by a steady light from the yellow LED. In keypad
mode, up to 10-digits can be entered.
Reader-to-microcontroller communication supervision is field
configurable via a jumper located on the reader. Either
supervised or non-supervised F/2F or Wiegand operation may
be selected. In supervised mode, if communication is lost with
the microcontroller, the red LED blinks three times, and
automatically goes offline (breach security feature) .
Operation
The reader constantly radiates a field that will power-up the
electronics in a proximity badge or key tag. In turn, the badge
sends its unique badge ID number (BID) to the reader. The
reader formats the BID and sends it to the microcontroller,
which makes the access decision. The decision is sent to the
reader which, for example, may result in the door being
unlocked and to the access control system database for
historical record purposes.
The magstripe reader will read a BID number from track two of
any ABA standard magstripe badge. The reader will send the
first four digits, up to a maximum of the first 16 digits, to the
microcontroller.
Standard Features
EReads GE proximity, ProxLite badges, and key tags
EReads standard magstripe badge with ABA format on track
2
EAvailable with or without a keypad
EMaximum proximity read range: 10 cm
ESelf-test upon power-up
ESelf-tuning; optimizes reader operation to site conditions
ESelectable supervised and non-supervised reader-to-
microcontroller communication
EWeather-resistant enclosure
EPhoenix-style pluggable field wiring connector makes reader
exchange quick and easy
EStandard DB-9 connector is plug compatible with IBM-5029
reader wiring
EOptional cold weather heater kit is available
The reader's user interface consists of two tri-state LEDs and
beeper. Beeper sound levels are switch selectable.
With Model 1000 readers, a steady red LED indicates reader
power is on and the reader is set for use, the yellow LED lights
and the beeper sounds once to indicate a valid badge read, and
the green LED lights to indicate the door strike has been
activated. The Model 1010 keypad-equipped reader operates
the same with the exception of the yellow LED, which lights
upon a valid badge read to indicate the reader is ready to
Model 1000 and 1010
Dual Technology Readers
accept PIN entry.
Installation
The included polycarbonate reader backplate has hole locations
marked for easy installation onto either a standard USA dualwidth electrical box or a similar standard European electrical
box. Mounting hardware is installer provided.
The readers include a tamper switch that will signal a
separation between the reader and its backplate. A connection
on the reader supports installation of a separate, installersupplied tamper switch, typically installed between the reader
backplate and the wall.
Readers are weather resistant. Reader installation must
provide protection from water, snow or ice. An optional heater
kit will keep the magstripe reader badge slot and reader keypad
free of ice and snow.
Dual Technology readers automatically sense and adjust to 12
VDC or 48 VDC input voltages. In 12 VDC installations, a
separate reader power supply may be required if the reader
installation is more than 150 m from its power source (typically
the microcontroller), or the input voltage wire is less than 20
AWG. The local power supply must be able to supply 200 mA
of regulated VDC at 12 VDC or 70 mA at 48 VDC.
Specifications
Operating temperature with
heater kit (option)
5° to 66° C or -35° to 66° C
Humidity range 0 to 95%, non-condensing
Dimensions
Height x Width x Depth 121 mm x 152 mm x 42 mm
Protection index IP-34
Cable length to
microcontroller
(power supplied by the
micro)
Cable length to
microcontroller
(power supplied at the
reader)
Cable type Belden 8725 or equivalent
Power supply 12 VDC @ 200 mA
Integral door strike relay,
NO-NC,
jumper selectable
Reader beeper sound levels Switch selectable
Tamper switch
Proximity read range Up to 101.6 mm
Magstripe reader, ABA track
2
Model 1010 keypad 12-key, tactile
Agency approvals FCC, subpart 15 and CE
SYSTEM SPECIFICATIONS
Microcontrollers
Reader processors Micro/4-8RP, Micro/5-2RP, 2SRP and 8RP
Communications, Model
1000
Communications, Model
1010
12V, 150 m. max 20 AWG
48V, 150 m. max 20 AWG
12V, 1500 m. max 20 AWG
48V, 1500 m. max 20 AWG
48 VDC @ 70 mA
28 VAC/DC @ 0.75A
Internal switch included, external connection
provided
First 4 digits, to a max. of 16 digits
Micro/2, Micro/4, Micro/5 (all), and Micro/
PX-2000
Supervised and Non-Supervised F/2F, 40-bit
Wiegand
Supervised F/2F only
Badge and key tag types
Proximity , ProxLite, ISO-ProxLite, and
Magstripe
Ordering Information
Part No. Description
430138001
520712001
430139001
470610001
As a company of innovation, UTC Fire & Security reserves the right to change product
specifications without notice. For the latest product specifications, visit UTC Fire & Security
online or contact your sales representative.
Model 1000 and 1010-2015-07-5 14:51:03 Released :29-AUG-11
Loading...