Page 1
2200 Series
Models: 2202, 2202A, 2202AU, 2204,
2204A, 2204AD, 2204AU, 2205A,
2205AU, 2207A, 2207AD, 2207AU,
2207AH, 2215
Installation Instructions
Mounting
2202, 2202A, 2202AU, 2204, 2204A, 2204AD,
2204AU
Secure the switch to the floor with appropriate fasteners
(wood or masonry). Be certain to position the switch where
it will not interfere with traffic. Attach the magnet on the
door so it lines up with the switch when the door is closed.
There is a 2" “make” distance between switch and magnet
to allow for door operational tolerance.
2205A, 2205AU, 2207A, 2207AD, 2207AU
Secure the contact to floor with appropriate fasteners
(wood or masonry). Be certain to position the contact
where it will not interfere with traffic. Align the contact
and magnet so the labels read in the same direction. Attach
the magnet to the door.
2207AH
Secure the switch to the floor as described above. Attach
an ohmmeter to the common and closed loop leads. The
meter should read INFINITY with the magnet away from
the switch. Align the magnet and contact so the labels read
in the same direction (switch is polarity sensitive). Bring
the magnet toward the switch until the meter again reads
INFINITY. Mark this point, and position the magnet
between these two marks. Attach the magnet directly to the
door or with L bracket, GE Interlogix Part Number 1912.
With the magnet positioned properly, the contact will be
more difficult to trip if an external magnet is used in an
attempt to defeat the switch.
2215
Select proper placement for your application. Align the
switch and magnet so the labels read in the same direction
(switch is polarity sensitive). Attach the magnet to the
door. Open the door to assure proper clearance.
2202A
2202AU
2215
Mounting Holes
.156" dia
2.00"
5.08cm
3.50"
8.89cm
3.50"
8.89cm
2.25"
5.71cm
2.10"
5.33cm
3.125"
7.94cm
3.50"
8.89cm
2.875"
7.30cm
2.00"
5.08cm
4.25"
10.80cm
2.00"
5.08cm
3.00"
7.62cm
0.44"
1.10cm
1.50"
3.81cm
3.81cm
1.375"
3.49cm
1.50"
3.81cm
1.50"
3.81cm
0.81"
2.06cm
1.50"
3.75"
0.95cm
1.00"
2.54cm
2.00"
5.08cm
1.50"
3.81cm
1.125"
2.86cm
0.50"
1.27cm
Magnet
Part No. 1958
(included)
Magnet
Part No. 1982
(included)
0.75"
1.91cm
Magnet
Part No. 1920
(included)
Page 2
x
Ordering Information
Part Loop Type Electrical Lead Type* Finish Gap Distance Magnet
Number Config. (Make)**
2202-L Closed N.O. 18'' vinyl jacketed Aluminum 360 Up to 3'' 1958
2202A-L Closed N.O. 18'' stainless steel armored cable Aluminum 360 Up to 3'' 1958
2202AU-L Closed N.O. 18'' stainless steel armored cable Aluminum 360 Up to 3'' 1982
2204-L Open or Closed SPDT 18' vinyl jacketed Aluminum 360 Up to 3" 1958
2204A-L Open or Closed SPDT 18" stainless steel armored cable Aluminum 360 Up to 3" 1958
2204AD-L Open or Closed DPDT 18" stainless steel armored cable Aluminum 360 Up to 1 1/2" 1958
2204AU-L Open or Closed SPDT 18" stainless steel armored cable Aluminum 360 Up to 3" 1982
2205A-L Closed N.O. 3' stainless steel armored cable Anodized Up to 3" 1958
2205AU-L Closed N.O. 3" stainless steel armored cable Anodized Up to 3" 1982
2207A-L Open or Closed SPDT 3' stainless steel armored cable Anodized Up to 3" 1958
2207AD-L Open or Closed DPDT 3' stainless steel armored cable Anodized Up to 1 1/2" 1958
2207AU-L Open or Closed SPDT 3' stainless steel armored cable Anodized Up to 3" 1982
2207AH-L Open or Closed SPDT 3' stainless steel armored cable Anodized 3/4" min., 1920
2 1/2 "max.
2215-L Closed N.O. 3' vinyl jacketed Anodized Up to 3" 1920
Accessories
1949-L Floor mount bracket for replacing ADEMCO and EPC switches
1912-L Aluminum L bracket for 1920 magnet
* Other lead types available; please inquire.
**Gap Specifications are nominal and may vary ± 20%. Gap Specifications are for contact to make. Break distance approximately 1.1 to 1.5
times make.
*** Form A: (2202, 2202A, 2202AU, 2205A, 2205AU, 2215)
Voltage: 100 V AC/DC MAX.
Current: 0.5 A MAX.
Power: 7.5 W MAX.
European Union Specifications; 48 V AC/DC Max., 0.5 A mp
***
WARNING: Each electrical rating is an individual maximum and
cannot be exceeded!
Listings:
C-UL-US 2202, 2202A, 2202AU,2204, 2204A,
2204AU, 2205A, 2205AU, 2207A, 2207AU,
2207AH
UL 2215
Form C: (2204, 2204A, 2204AD, 2204AU, 2207A, 2207AD,
2207AU, 2207AH)
Voltage: 30 V AC/DC MAX.
Current: 0.25 A MAX.
Power: 3.0 W MAX.
Lead Functions
Form C Models (2204, 2204A, 2204AD, 2204AU, 2207A,
2207AD, 2207AU, 2207AH)
Lead Color Function
Black Common
White Closed Loop (N.O.)
Red Open Loop (N.C.)
10218 Rev D 09/03
Made in Taiwan
GE Interlogi
Loading...