Page 1
Euro Trigon 02
Trigon K
Page 2
AVVERTENZE PER L’INSTALLATORE
OBBLIGHI GENERALI PER LA SICUREZZA
1) ATTENZIONE! È importante per la sicurezza delle persone seguire attentamente tutta l’istruzione. Una errata installazione o un errato uso del prodotto
può portare a gravi danni alle persone.
2) Leggere attentamente le istruzioni prima di iniziare l’installazione del prodotto.
3) I materiali dell’imballaggio (plastica, polistirolo, ecc.) non devono essere
lasciati alla portata dei bambini in quanto potenziali fonti di pericolo.
4) Conservare le istruzioni per riferimenti futuri.
5) Questo prodotto è stato progettato e costruito esclusivamente per l’utilizzo
indicato in questa documentazione. Qualsiasi altro utilizzo non espressamente indicato potrebbe pregiudicare l’integrità del prodotto e/o rappresentare fonte di pericolo.
6) GENIUS declina qualsiasi responsabilità derivata dall’uso improprio o diverso
da quello per cui l’automatismo è destinato.
7) Non installare l’apparecchio in atmosfera esplosiva: la presenza di gas o fumi
infiammabili costituisce un grave pericolo per la sicurezza.
8) Gli elementi costruttivi meccanici devono essere in accordo con quanto
stabilito dalle Norme EN 12604 e EN 12605.
Per i Paesi extra-CEE, oltre ai riferimenti normativi nazionali, per ottenere un
livello di sicurezza adeguato, devono essere seguite le Norme sopra riportate.
9) GENIUS non è responsabile dell’inosservanza della Buona Tecnica nella costruzione delle chiusure da motorizzare, nonché delle deformazioni che
dovessero intervenire nell’utilizzo.
10) L’installazione deve essere effettuata nell’osservanza delle Norme EN 12453
e EN 12445. Il livello di sicurezza dell’automazione deve essere C+E.
11) Prima di effettuare qualsiasi intervento sull’impianto, togliere l’alimentazione
elettrica.
12) Prevedere sulla rete di alimentazione dell’automazione un interruttore
onnipolare con distanza d’apertura dei contatti uguale o superiore a 3 mm.
È consigliabile l’uso di un magnetotermico da 6A con interruzione onnipolare.
13) Verificare che a monte dell’impianto vi sia un interruttore differenziale con
soglia da 0,03 A.
14) Verificare che l’impianto di terra sia realizzato a regola d’arte e collegarvi
le parti metalliche della chiusura.
15) L’automazione dispone di una sicurezza intrinseca antischiacciamento costituita da un controllo di coppia. E' comunque necessario verificarne la sogli
di intervento secondo quanto previsto dalle Norme indicate al punto 10.
16) I dispositivi di sicurezza (norma EN 12978) permettono di proteggere eventuali aree di pericolo da Rischi meccanici di movimento, come ad Es.
schiacciamento, convogliamento, cesoiamento.
17) Per ogni impianto è consigliato l’utilizzo di almeno una segnalazione luminosa nonché di un cartello di segnalazione fissato adeguatamente sulla struttura dell’infisso, oltre ai dispositivi citati al punto “16”.
18) GENIUS declina ogni responsabilità ai fini della sicurezza e del buon funzionamento dell’automazione, in caso vengano utilizzati componenti dell’impianto non di produzione GENIUS.
19) Per la manutenzione utilizzare esclusivamente parti originali GENIUS.
20) Non eseguire alcuna modifica sui componenti facenti parte del sistema
d’automazione.
21) L’installatore deve fornire tutte le informazioni relative al funzionamento
manuale del sistema in caso di emergenza e consegnare all’Utente
utilizzatore dell’impianto il libretto d’avvertenze allegato al prodotto.
22) Non permettere ai bambini o persone di sostare nelle vicinanze del prodotto
durante il funzionamento.
23) Tenere fuori dalla portata dei bambini radiocomandi o qualsiasi altro datore
di impulso, per evitare che l’automazione possa essere azionata involontariamente.
24) Il transito tra le ante deve avvenire solo a cancello completamente aperto.
25) L’Utente utilizzatore deve astenersi da qualsiasi tentativo di riparazione o
d’intervento diretto e rivolgersi solo a personale qualificato.
26) Tutto quello che non è previsto espressamente in queste istruzioni non è
permesso
IMPORTANT NOTICE FOR THE INSTALLER
GENERAL SAFETY REGULATIONS
1) ATTENTION! To ensure the safety of people, it is important that you read
all the following instructions. Incorrect installation or incorrect use of the
product could cause serious harm to people.
2) Carefully read the instructions before beginning to install the product.
3) Do not leave packing materials (plastic, polystyrene, etc.) within reach of
children as such materials are potential sources of danger.
4) Store these instructions for future reference.
5) This product was designed and built strictly for the use indicated in this
documentation. Any other use, not expressly indicated here, could compromise the good condition/operation of the product and/or be a source of
danger.
6) GENIUS declines all liability caused by improper use or use other than that for
which the automated system was intended.
7) Do not install the equipment in an explosive atmosphere: the presence of
inflammable gas or fumes is a serious danger to safety.
8) The mechanical parts must conform to the provisions of Standards EN 12604
and EN 12605.
For non-EU countries, to obtain an adequate level of safety, the Standards
mentioned above must be observed, in addition to national legal regulations.
9) GENIUS is not responsible for failure to observe Good Technique in the
construction of the closing elements to be motorised, or for any deformation
that may occur during use.
10) The installation must conform to Standards EN 12453 and EN 12445. The safety
level of the automated system must be C+E.
11) Before attempting any job on the system, cut out electrical power.
12) The mains power supply of the automated system must be fitted with an allpole switch with contact opening distance of 3mm or greater. Use of a 6A
thermal breaker with all-pole circuit break is recommended.
13) Make sure that a differential switch with threshold of 0.03 A is fitted upstream
of the system.
14) Make sure that the earthing system is perfectly constructed, and connect
metal parts of the means of the closure to it.
15) The automated system is supplied with an intrinsic anti-crushing safety device
consisting of a torque control. Nevertheless, its tripping threshold must be
checked as specified in the Standards indicated at point 10.
16) The safety devices (EN 12978 standard) protect any danger areas against
mechanical movement Risks, such as crushing, dragging, and shearing.
17) Use of at least one indicator-light is recommended for every system, as well
as a warning sign adequately secured to the frame structure, in addition to
the devices mentioned at point “16”.
18) GENIUS declines all liability as concerns safety and efficient operation of the
automated system, if system components not produced by GENIUS are used.
19) For maintenance, strictly use original parts by GENIUS.
20) Do not in any way modify the components of the automated system.
21) The installer shall supply all information concerning manual operation of the
system in case of an emergency, and shall hand over to the user the warnings
handbook supplied with the product.
22) Do not allow children or adults to stay near the product while it is operating.
23) Keep remote controls or other pulse generators away from children, to
prevent the automated system from being activated involuntarily.
24) Transit through the leaves is allowed only when the gate is fully open.
25) The user must not attempt any kind of repair or direct action whatever and
contact qualified personnel only.
26) Anything not expressly specified in these instructions is not permitted.
CONSIGNES POUR L'INSTALLATEUR
RÈGLES DE SÉCURITÉ
1) ATTENTION! Il est important, pour la sécurité des personnes, de suivre à la
lettre toutes les instructions. Une installation erronée ou un usage erroné
du produit peut entraîner de graves conséquences pour les personnes.
2) Lire attentivement les instructions avant d'installer le produit.
3) Les matériaux d'emballage (matière plastique, polystyrène, etc.) ne doivent
pas être laissés à la portée des enfants car ils constituent des sources
potentielles de danger.
4) Conserver les instructions pour les références futures.
5) Ce produit a été conçu et construit exclusivement pour l'usage indiqué dans
cette documentation. Toute autre utilisation non expressément indiquée
pourrait compromettre l'intégrité du produit et/ou représenter une source
de danger.
6) GENIUS décline toute responsabilité qui dériverait d'usage impropre ou
différent de celui auquel l'automatisme est destiné.
7) Ne pas installer l'appareil dans une atmosphère explosive: la présence de
gaz ou de fumées inflammables constitue un grave danger pour la sécurité.
8) Les composants mécaniques doivent répondre aux prescriptions des Normes
EN 12604 et EN 12605.
Pour les Pays extra-CEE, l'obtention d'un niveau de sécurité approprié exige
non seulement le respect des normes nationales, mais également le respect
des Normes susmentionnées.
9) GENIUS n'est pas responsable du non-respect de la Bonne Technique dans la
construction des fermetures à motoriser, ni des déformations qui pourraient
intervenir lors de l'utilisation.
10) L'installation doit être effectuée conformément aux Normes EN 12453 et EN
12445. Le niveau de sécurité de l'automatisme doit être C+E.
11) Couper l'alimentation électrique avant toute intervention sur l'installation.
12) Prévoir, sur le secteur d'alimentation de l'automatisme, un interrupteur
omnipolaire avec une distance d'ouverture des contacts égale ou supérieure
à 3 mm. On recommande d'utiliser un magnétothermique de 6A avec
interruption omnipolaire.
13) Vérifier qu'il y ait, en amont de l'installation, un interrupteur différentiel avec
un seuil de 0,03 A.
14) Vérifier que la mise à terre est réalisée selon les règles de l'art et y connecter
les pièces métalliques de la fermeture.
15) L'automatisme dispose d'une sécurité intrinsèque anti-écrasement, formée
d'un contrôle du couple. Il est toutefois nécessaire d'en vérifier le seuil
d'intervention suivant les prescriptions des Normes indiquées au point 10.
16) Les dispositifs de sécurité (norme EN 12978) permettent de protéger des
zones éventuellement dangereuses contre les Risques mécaniques du
mouvement, comme l'écrasement, l'acheminement, le cisaillement.
Page 3
AUTOMATION EURO TRIGON 02
ENGLISH
These instructions apply to the following model:
EURO TRIGON 02
The external automation with articulated arms automates
residential swing-leaf gates with leaves of up to 3m in length, and
is ideal for applications on large pilasters without the need to
provide niches (sometimes required to observe the installation
dimensions of piston driven devices).
It consists of an irreversible electro-mechanical operator with
guard and an articulated-arm activation system to be fitted to
the gate with the appropriate accessories.
The irreversible system ensures the gate is mechanical locked
when the motor is not operating. No lock need be installed for
leaves up to 2m in length.
A manual release makes it possible to move the gate in the event
of a power-cut or fault.
To obtain anti-crushing protection, you have to use electronic
appliances with a torque control electronic device.
The automation was designed and manufactured to control
access of vehicles. Avoid any other use whatever.
1. DESCRIPTION AND TECHNICAL SPECIFICATIONS
TAB. 1 TECHNICAL SPECIFICATION OF OPERATOR
MODEL
Power supply
Power absorption
Current absorption
Max torque
Starting capacitor
Thermal protection for winding
Reduction ratio
Angular velocity
Ambient temperature
Use frequency
Cycles / hour
Weight of gearmotor
Protection class
Gearmotor overall dimension
EUROTRIGON 02
TRIGON K
230V~ 50Hz 24Vdc
280W 40W
1.2A 2A
250Nm 200Nm
8µF
140°C
1:700
8°/sec
-20°C +55°C
S3 - 30%
> 30
11.5Kg
IP44
see fig.2
Leaf max length
2. DIMENSIONS
EUROTRIGON 02 24
TRIGON K 24
S3 - 100%
> 100
3 m
1
5
2
6
4
7
3
1) Guard
2) Operator securing base-plate
3) Release wrench
4) Release
5) Gearmotor
6) Transmission shaft
7) Straight lever of articulated arm
8) Curved lever of articulated arm
9) Front coupling
0
3
1
130
4
9
8
100
Fig. 1 Fig. 2
•measurements in mm
1
0
60
Ø 10
6
0
1
1
5
3
9
0
8
4
332
250
4
0
5
21.5
5
Page 4
ENGLISH
3. ELECTRICAL EQUIPMENT (standards system)
1) Operators
2) Photocells
3) Electronic equipment
4) Key-operated push-button
5) Radio receiver
6) Flashlight
Notes: 1) To lay electrical cables, use adequate rigid and/
or flexible tubes.
2) Always separate low voltage accessories from
those operating at 230V~. To avoid any
interference, always use separate sheaths.
Fig. 3
4. INSTALLATION OF AUTOMATION
4.1. PRELIMINARY CHECKS
To ensure safety and an efficient automation, make sure the
following requirements are met:
• The gate structure must be suitable for automation. In
particular, make sure it is sufficiently sturdy and rigid, and
that its dimensions are in line with those indicated in the
technical specifications.
• Make sure that the leaves move properly and uniformly,
without any irregular friction during their entire travel.
• Check if hinges are in good condition.
• Make sure the travel limit mechanical stops are present.
• We advise you to carry out any metalwork jobs before
installing the automation.
4.2. INSTALLATION DIMENSIONS
Establish the installation position of the operator by consulting Fig.
4-5-6.
4.2.1. RECOMMENDED DIMENSIONS FOR INWARD OPENING
B C
X
A
40 / 60
°
α
Notes: As for 120° openings the curved arm must be fixed
to the hole marked with the letter X
αα
α
A B C (max)
αα
60÷110 110÷130 730 90°
110÷160 110÷130 720 90°
160÷210 110÷130 710 90°
210÷260 110÷130 700 90°
260÷310 110÷130 690 90°
310÷360 110÷130 670 90°
60÷110 190÷210 650 120°
110÷160 230÷250 600 120°
160÷210 290÷310 540 120°
210÷260 310÷330 510 120°
•measurements in mm
Fig. 5
4.2.2. RECOMMENDED DIMENSIONS FOR OUTWARD OPENING
α
°
40 / 60
A
~ 41
~ 200
•measurements in mm
Fig. 4
A B C (max)
60÷110 110÷130 430 90°
110÷160 110÷130 380 90°
160÷210 110÷130 330 90°
210÷260 110÷130 280 90°
260÷310 110÷130 240 90°
•measurements in mm
6
CB
αα
α
αα
Fig. 6
Page 5
4.3. INSTALLATION STEPS
The operator, base-plate and articulated arm are designed
either for right-hand or left-hand (Fig. 7) installation.
ENGLISH
SX
DX
Fig. 7
• Secure the base-plate to the pilaster, using Ø10 screws and
suitable expansion plugs (Fig. 8), and check it is perfectly
horizontal.
• Fit the gearmotor unit on the base-plate and secure it with
the two screws, nuts and flexible washers (Fig.8).
• The transmission shaft must always face downward.
SX
DX
Fig. 8
• Assemble the articulated arm and front coupling as shown
in Fig. 9.
SX
DX
Fig. 11 Fig. 12
• In both cases, provisionally remove the coupling from the arm
in order to secure it.
• Fit the guards on the operator (Fig. 10).
• Re-lock the operator (chapter 6.)
• Make the electrical connections of the selected electronic
appliance, observing the annexed instructions.
4.4. TEST OF THE AUTOMATION
When you have finished installation, carefully check the operating
efficiency of the automation and of all accessories connected
to it, safety devices in particular.
Hand the “User’s Guide” page to the Client, and describe how
the operator should function and be used correctly, stressing the
potentially dangerous areas of the automation.
5. MANUAL OPERATING MODE
If the gate has to be operated manually in the event of a powercut or fault to the automation, use the release device as follows:
• Fit the supplied Allen wrench and turn it by about a half turn
until it stops, in the direction shown in Fig. 13, depending on
type of installation.
6. RESTORING NORMAL OPERATING MODE
To avoid an involuntary pulse from activating the gate during the
manoeuvre, before re-locking the operator , switch off power to
the system.
• Fit the supplied Allen wrench and turn it by about a half turn
until it stops, in the direction shown in Fig. 13, depending on
type of installation.
Fig. 9
• Fit the straight lever of the articulated arm on the gearmotor
shaft and tighten it with the supplied screw and washer (Fig.
10).
• Release the operator (chapter 5.)
• Establish the securing position of the front coupling on the
leaf, observing dimension “C” defined previously (chapter
4.2). Check that arm and coupling are perfectly horizontal.
• The coupling may be welded directly onto the leaf (Fig. 11)
or screwed by using the threaded inserts (Fig. 12).
SX
DX
Fig. 10
DX
SBLOCCA / UNLOCK
DEBLOQUE / ENTRIEGELT
DESBLOQUEAR
BLOQUE / VERRIEGELT
BLOCCA / LOCK
BLOQUE / VERRIEGELT
BLOQUEAR
SX
SBLOCCA / UNLOCK
DEBLOQUE / ENTRIEGELT
DESBLOQUEAR
Fig. 13
7. MAINTENANCE
Do the following jobs at least every six months:
• Check if motor torque is correctly set.
• Check efficiency of the release system.
• Check efficiency of safety devices.
8. REPAIRS
For any repairs, contact our authorised Repair Centres.
BLOCCA / LOCK
BLOQUEAR
7
Page 6
ENGLISH
AUTOMATION TRIGON K
Application with telescopic arm for folding doors
These instructions are valid for the following model:
TRIGON K
Thanks to the inside telescopic arm system, it is possible to
automate folding doors with two panels up to 3 m in length (1.5
m per panel).
The irreversible system mechanically locks the door when the
motor is not operating. A manual release allows the door to be
moved during a black-out or failure.
Electronic devices equipped with an electronic torque adjustment
device must be used in order to implement anti-crushing safety.
1. INSTALLATION PROCEDURE
1) The operator is installed on the hinged panel directly to the
pilaster (fig. 2) or, when the door is open, if there is not enough
space behind the door for the operator, it should be installed
on the outermost panel (fig. 3). The installation dimensions
are valid in both cases.
8
2) Put the base plate A on the panel, observing the dimensions
as indicated in fig. 4 and weld or attach it to the panel using
4 screws.
3) Find the position halfway on the second panel and install the
angle bar with pin B. Then weld or attach it using 2 screws
while following the dimensions show in fig. 4.
4) Mount the geared motor C on the base plate A using the
relative screws, washers and nuts supplied (fig. 5). Note: the
grooved section must be facing up.
5) Release the geared motor C and fit the telescopic arm D on
the grooved channel.
6) Turn the telescopic arm by hand until the hole on the sheath
is on the pin of angle bar B. Fit it into position and lock it using
a seeger ring.
7) Move the door by hand and make sure that none of the
installed parts strikes against the door or the pilasters.
8) If necessary, shorten the sheath to remain within the limit of
50 mm as indicated in fig. 2 and fig. 3. Note: the sheath and
the internal element must have the same length.
Fig. 1
.
n
i
M
0
5
6
2
1
4
3
1) Guide tube
7
9
2) Telescopic arm plate
3) Telescopic arm fitting
4) Operator fixing base plate
5
5) Housing
6) Release
7) Release key
8) Transmission shaft
9) Gearmotor
3000 Max.
3000 Max.
.
n
i
M
0
5
•measurements in mm •measurements in mm
40±260
250 110±20
A
120±20
B
•measurements in mm
Fig. 2 Fig. 3
5±2
==
C
A
Fig. 4 Fig. 5
8
D
B
Page 7
DICHIARAZIONE CE DI CONFORMITÁ PER MACCHINE
(DIRETTIVA 89/392 CEE, ALLEGATO II, PARTE B)
Fabbricante: GENIUS s.r.l.
Indirizzo: Via Padre Elzi, 32
Dichiara che: EUROTRIGON 02 - TRIGON K
• è costruito per essere incorporato in una macchina o
• è conforme ai requisiti essenziali di sicurezza
e inoltre dichiara che non è consentito mettere in servizio il
macchinario fino a che la macchina in cui sarà incorporata o
di cui diverrà componente sia stata identificata e ne sia stata
dichiarata la conformità alle condizioni della Direttiva 89/392/
CEE e successive modifiche trasposta nella legislazione
nazionale dal DPR n° 459 del 24 Luglio 1996.
Grassobbio, 1 Marzo 2002
24050 - Grassobbio
BERGAMO - ITALIA
per essere assemblato con altri macchinari per
costituire una macchina ai sensi della Direttiva 89/
392 CEE, e successive modifiche 91/368/CEE, 93/44/
CEE, 93/68/CEE;
delle seguenti altre direttive CEE:
73/23 CEE e successiva modifica 93/68/CEE.
89/336 CEE e successiva modifica 92/31 CEE e
93/68/CEE
L’Amministratore Delegato
D. Gianantoni
EC MACHINE DIRECTIVE COMPLIANCE DECLARATION
(DIRECTIVE 89/392 EEC, APPENDIX II, PART B)
Manufacturer: GENIUS s.r.l.
Address: Via Padre Elzi, 32
Hereby declares that: EUROTRIGON 02 - TRIGON K
• is intended to be incorporated into machinery, or to
be assembled with other machinery to constitute
machinery in compliance with the requirements of
Directive 89/392 EEC, and subsequent amendments
91/368 EEC, 93/44 EEC and 93/68 EEC;
• complies with the essential safety requirements in the
following EEC Directives:
73/23 EEC and subsequent amendment 93/68 EEC.
89/336 EEC and subsequent amendments 92/31 EEC
and 93/68 EEC.
and furthermore declares that unit must not be put into service
until the machinery into which it is incorporated or of which it
is a component has been identified and declared to be in
conformity with the provisions of Directive 89/392 ECC and
subsequent amendments enacted by the national
implementing legislation.
Grassobbio, 1 March 2002
24050 - Grassobbio
BERGAMO - ITALY
Managing Director
D. Gianantoni
DÉCLARATION CE DE CONFORMITÉ
(DIRECTIVE EUROPÉENNE "MACHINES" 89/392/CEE,
ANNEXE II, PARTIE B)
Fabricant: GENIUS s.r.l.
Adresse:
Déclare d’ une part EUROTRIGON 02 - TRIGON K
• est prévue soit pour être incorporée dans une machine,
soit pour être assemblée avec d’autres composants ou
parties en vue de former une machine selon la directive
européenne "machines" 89/392 CEE, modifiée 91/368
CEE, 93/44 CEE, 93/68 CEE.
• satisfait les exigences essentielles de sécurité des
directives CEE suivantes:
73/23 CEE, modifiée 93/68 CEE.
89/336 CEE, modifiée 92/31 CEE et 93/68 CEE.
et d’autre part
qu’il est formellement interdit de mettre en fonction l'automatisme en
question avant que la machine dans laquelle il sera intégrée ou dont
il constituera un composant ait été identifiée et déclarée conforme
aux exigences essentielles de la directive européenne "machines"
89/392/CEE, et décrets de transposition de la directive.
Grassobbio, le 1 Mars 2002
Via Padre Elzi, 32
24050 - Grassobbio
BERGAMO - ITALIE
L’Administrateur Délégué
D. Gianantoni
DECLARACIÓN DE CONFORMIDAD CE PARA MÁQUINAS
(DIRECTIVA 89/392 CEE, ANEXO II, PARTE B)
Fabricante: GENIUS s.r.l.
Dirección: Via Padre Elzi, 32
Declara que: EUROTRIGON 02 - TRIGON K
• Ha sido construido para ser incorporado en una
• Cumple los requisitos esenciales de seguridad
Asimismo, declara que no está permitido poner en marcha el
equipo si la máquina en la cual será incorporado, o de la cual
se convertirá en un componente, no ha sido identificada o no
ha sido declarada su conformidad a lo establecido por la
Directiva 89/392 CEE y sus sucesivas modificaciones, y a la ley
que la incorpora en la legislación nacional.
Grassobbio, 1º de Marzo de 2002.
24050 - Grassobbio
BERGAMO - ITALIA
máquina, o para ser ensamblado con otros
mecanismos a fin de constituir una máquina con
arreglo a la Directiva 89/392 CEE y a sus sucesivas
modificaciones 91/368 CEE, 93/44 CEE y 93/68 CEE.
establecidos por las siguientes directivas CEE:
73/23 CEE y sucesiva modificación 93/68 CEE,
89/336 CEE y sucesivas modificaciones 92/31 CEE y
93/68 CEE.
Administrador Delegado
D. Gianantoni
EG-KONFORMITÄTSERKLÄRUNG ZU MASCHINEN
(gemäß EG-Richtlinie 89/392/EWG, Anhang II, Teil B)
Hersteller: GENIUS s.r.l.
Adresse: Via Padre Elzi, 32
erklärt hiermit, daß: EUROTRIGON 02 - TRIGON K
• zum Einbau in eine Maschine oder mit anderen
Maschinen zu einer Maschine im Sinne der Richtlinie
89/392 EWG und deren Änderungen 91/368 EWG,
93/44 EWG, 93/68 EWG vorgesehen ist.
• den wesentlichen Sicherheitsbestimmungen
folgender anderer EG-Richtlinien entspricht:
73/23 EWG und nachträgliche Änderung 93/68 EWG
89/336 EWG und nachträgliche Änderung 92/31 EWG
sowie 93/68 EWG
und erklärt außerdem, daß die Inbetriebnahme solange
untersagt ist, bis die Maschine, in welche diese Maschine
eingebaut wird oder von der sie ein Bestandteil ist, den
Bestimmungen der Richtlinie 89/392 EWG sowie deren
nachträglichen Änderungen entspricht.
Grassobbio, 1 März 2002
24050 - Grassobbio
BERGAMO - ITALIEN
Der Geschäftsführer
D. Gianantoni
Timbro rivenditore: / Distributor’s stamp: / Timbre de l’agent: /
Sello del revendedor: / Fachhändlerstempel:
Le descrizioni e le illustrazioni del presente manuale non sono
impegnative. GENIUS si riserva il diritto, lasciando inalterate le
caratteristiche essenziali dell’apparecchiatura, di apportare in
qualunque momento e senza impegnarsi ad aggiornare la
presente pubblicazione, le modifiche che essa ritiene convenienti per miglioramenti tecnici o per qualsiasi altra esigenza di
carattere costruttivo o commerciale.
The descriptions and illustrations contained in the present
manual are not binding. GENIUS reserves the right, whils leaving the main features of the equipments unaltered, to undertake any modifications to holds necessary for either technical
or commercial reasons, at any time and without revising the
present publication.
Les descriptions et les illustrations du présent manuel sont
fournies à titre indicatif. GENIUS se réserve le droit d’apporter à
tout moment les modifications qu’elle jugera utiles sur ce
produit tout en conservant les caractéristiques essentielles,
sans devoir pour autant mettre à jour cette publication .
Las descripciones y las ilustraciones de este manual no
comportan compromiso alguno. GENIUS se reserva el derecho,
dejando inmutadas las características esenciales de los
aparatos, de aportar, en cualquier momento y sin
comprometerse a poner al día la presente publicación, todas
las modificaciones que considere oportunas para el
perfeccionamiento técnico o para cualquier otro tipo de
exigencia de carácter constructivo o comercial.
Die Beschreibungen und Abbildungen in vorliegendem
Handbuch sind unverbindlich. GENIUS behält sich das Recht
vor, ohne die wesentlichen Eigenschaften dieses Gerätes zu
verändern und ohne Verbindlichkeiten in Bezung auf die
Neufassung der vorliegenden Anleitungen, technisch bzw,
konstruktiv / kommerziell bedingte Verbesserungen
vorzunehmen.
GENIUS s.r.l.
Via Padre Elzi, 32
24050 - Grassobbio
BERGAMO-ITALY
tel. 0039.035.4242511
fax. 0039.035.4242600
info@geniusg.com
www.geniusg.com
I0233 REV.4
Loading...