Genie HDUB4P User Manual

HDUB4P

4 Channel Passive HD

Video UTP Transceiver

User Manual

HDUB4P - 4 Channel Passive HD UTP Transciever

2

1. Introduction

2. Key Features

3. Technical Specication

4. Board Diagram

The HDUB4P is a 4 Channel Passive HD (Non-Amplied) Video UTP Transceiver that allows transmission
of real time and high performance colour or monochrome CCTV video or HD-CVI / AHD / HD-TVI / HD
video over UTP cable which is ideal for multi-point surveillance.

• Passive, No Need for a Power Supply

• HD-CVI, HD-TVI, AHD, CVBS 4 in 1 Compatible Design

• Real-Time Transmission, No Delay

• Strong Surge Protection, ESD and Lighting Protection

• Supports MIT Structure

• Easy Operation

Model Number HDUB4P

Transmission Channel 4 Channel

Video Connector 4 Channel

Transmission Distance HD-CVI (720p): 370m, HD-CVI (1080p): 100m

HD-TVI (720p): 200m, HD-TVI (1080p): 200m
AHD-L/M (720p): 250m, AHD-L/M (960p): 250m
AHD-H (1080p): 250m, Anaglogue Video: 500m

Coaxial Video Connector Female BNC Connector

UTP Cable Video Connector Female RJ45 Connector, 8 Channel Screw Push Terminal

Compatible Video Format HD-CVI, HD-TVI, AHD, CVBS

Signal Transmission Width 0-70MHz

Anti-Interference >60dB

Coaxial Video Connector Surge 2KV (Different Mode) Per: IEC61000-4-5

UTP Cable Communication
Connector Surge Protection

2KV (Different Mode) per: IEC6100-4-5

ESD 1a Contact Discharge Level 3

1b Air Discharge Level 3
Per: IEC6100-4-2

Operation Temperature 0 ~ 55°C

Storage Temperature -40°C ~ 85°C

Humidity 0~95%

Dimensions (L x W x H) 85 x 82 x 25 mm (Including Connector Length)

*Design and Specications are subject to change without notice.

Front Back

Coaxial Port

RJ45 Port

Terminal Block Port

PoE OUT PoE OUT

PoE IN

V

I

D

EO

3

4

1

2

V

I

D

EO

3

4

1

2

V

I

D

EO

3

4

1

2

HDUB4P - 4 Channel Passive HD UTP Transciever

3

5. Application Diagram

UTP CAT5 / CAT5e / CAT6

DVR

Coax

Monitor

NOTICE

• Transmission distance is related to wire quality. Please use standard UTP cable and coaxial cable.

• RJ45 connector and screw push terminal connection mode can not use at the same time. Choose

only one of them.

6. Installation Steps

7. Troubleshooting

1. Turn off the power of the camera and display before installation.

2. Check if the cables and display device are occupied.

3. Connect monitor or DVR and BNC connectorof the product over coaxial cable

4. Connect the product push terminal UTP cable connector or RJ45 connector and camera output port
over UTP cable.

5. Check whether installation is correct, the device is good, make sure all connection is reliable, connect
power cable, system is power on.

6. Make sure network is normal.

Please follow below if the device doesn’t work:

• Check if its according to the manual.

• If you choose RJ-45, make sure both ends of UTP cable are both the same (568A or 568B).

• If you choose green terminal block, make sure cable of same colour be in the same pin.

• Check all connections such as BNC, RJ-45.

• Make sure the real distance doesnt exceed the allowed transmission distance.

• Make sure the cables are good quality.

• Replace the device at question by a normal working device.

• If the problem still occurs, please contact the dealer.

GENIE CCTV LTD.

CCTV House, City Park, Watchmead, Welwyn Garden City, Hertfordshire, AL7 ILT

Tel: [phone] Fax: [phone]

www.geniecctv.com

Edition. GN- May 2016