Genie HDUB16RP User Manual

Page 1
HDUB16RP
16 Channel Passive HD
Video UTP Transceiver
User Manual
Page 2
2
1. Introduction
2. Key Features
3. Technical Specication
4. Board Diagram
The HDUB16RP is a 16 Channel Passive HD (Non-Amplied) Video UTP Transceiver that allows transmission of real time and high performance colour or monochrome CCTV video or HD-CVI / AHD / HD-TVI / HD video over UTP cable. The device is 1U rack-mountable, ideal for multi-point surveillance.
Passive, No Need for a Power Supply
HD-CVI, HD-TVI, AHD, CVBS 4 in 1 Compatible Design
RJ-45 or Green Terminal Block to be chosen to connect to UTP Cable
Compact Design, 1U Rack Mountable
Plug and Play, Simple Installation
Super Surge Protection and Interference rejection
Model Number HDUB16RP
Transmission Channel 16 Channel
Transmission Distance HD-CVI (720p): 370m, HD-CVI (1080p): 100m
HD-TVI (720p): 200m, HD-TVI (1080p): 200m AHD-L/M (720p): 250m, AHD-L/M (960p): 250m AHD-H (1080p): 250m, Anaglogue Video: 500m
Video Connector BNC-F
UTP Cable Video Connector 8 Pin Green Terminal Block, RJ-45
Compatible With HD-CVI, HD-TVI, AHD, CVBS, PAL, NTSC, SECAM Video
Signal Transmission Band 0-70MHz
Interference Rejection >60dB
Video Connector Surge 2KV (Common Mode) Per: IEC61000-4-5
UTP Cable Connector Surge Protection 2KV (Different Mode) per: IEC6100-4-5
ESD Contact Discharge: 6000V
Air Discharge: 8000V Per: IEC61000-4-2
Operation Temperature 0 ~ 55°C
Storage Temperature -40°C ~ 85°C
Humidity 0~95% (Non-Condensing)
Dimensions (L x W x H) 430 x 100 x 44.5 (1U)
*Design and Specications are subject to change without notice.
RJ-45 8 Pin Green
Terminal Block
BNC-F
PoE OUT
Page 3
HDUB16RP - 16 Channel Passive HD UTP Transciever
3
5. Application Diagram
UTP CAT5 / CAT5e / CAT6
DVR
Coaxial Cable
NOTICE
Transmission distance is related to wire quality. Please use standard UTP cable and coaxial cable.
RJ45 connector and screw push terminal connection mode can not use at the same time. Choose
only one of them.
6. Installation Steps
7. Troubleshooting
1. Please power off camera, PC, DVR, IPC and Monitor which are to be used.
2. Connect cameras with transmitter via BNC cable.
3. Connect DVR with it via BNC cable.
4. Connect transmitter and receiver via UTP cable.
5. Power camera, DVR, Monitor etc.
Please follow below if the device doesn’t work:
Check if its according to the manual.
If you choose RJ-45, make sure both ends of UTP cable are both the same (568A or 568B).
If you choose green terminal block, make sure cable of same colour be in the same pin.
Check all connections such as BNC, RJ-45.
Make sure the real distance doesnt exceed the allowed transmission distance.
Make sure the cables are good quality.
Replace the device at question by a normal working device.
If the problem still occurs, please contact the dealer.
Monitor
Monitor
Monitor
Page 4
GENIE CCTV LTD.
CCTV House, City Park, Watchmead, Welwyn Garden City, Hertfordshire, AL7 ILT
Tel: +44 (0) 1707 330541 Fax: +44 (0) 1707 330543
www.geniecctv.com
Edition. GN- May 2016
Loading...