Genie HDC222 Operation Manual

These servicing instructions are for use by qualied service personnel only.

To reduce the risk of electric shock do not perform any servicing other than that

contained in the operating instructions unless you are qualied to do so.

Use CEPower Supply Only

CAUTION

2

CONTENTS

1. CAUTIONS

2. IMPORTANT SAFETY INSTRUCTIONS

3. FEATURES

4. EQUIPMENT AND ACCESSORIES

5. CAMERA COMPONENT DESCRIPTIONS

6. INSTALLATION

7. DIMENSIONS

8. SPECIFICATION

9. OSD MANUAL

3

1. CAUTIONS

4

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference
that may cause undesired operation.

Note

This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.”

WARNING

This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

Caution

Any changes or modications in construction of this devices which are not expressly

approved by the party responsible for compliance could void the user’s authority to
operate the equipment.

1. A regulated DC12V 1A power supply is recommended for use with this camera
for the best picture and the most stable operation.

An unregulated power supply can cause damage to the camera.
When an unregulated power supply is applied, the product warranty will be void.

2. It is recommended that the camera is used with a monitor that is of CCTV quality
75 video impedance level.
If your monitor is switched to high impedance then please adjust accordingly.

3. Do not attempt to disassemble the camera to gain access to the internal components.
Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reective light, which may

cause smear on the picture and possible damage to the CCD.

5. Do not remove the serial sticker for the warranty service.

6. Do not expose the camera to rain or other types of liquid.

7. The apparatus must be connected to a mains socket-outlet with a protective earthing
connection.

1. CAUTIONS

5

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with
separate collection systems)

This marking shown on the product or its literature, indicate that it should not
be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.

This product should not be mixed with other commercial wastes purchased this

product, or their local government ofce, for details of where and how they can

take item for environmentally safe recycling.

Business users should contact their supplier and check the terms and
conditions of the purchase contract.
Household users should contact either the retailer where they for disposal.

2. IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with a dry lint free cloth.

7) Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including ampliers) that produce heat.

9) Do not defeat the safety purpose of the polarised or grounding-type plug. A
polarised plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third

prong are provided for your safety. If the provided plug does not t into your

outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specied by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specied by

the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to
avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long

periods of time.

14) Refer all servicing to qualied service personnel. Servicing is required when

the apparatus has been damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.

6

3. FEATURES

• High Resolution

SONY 1/3” 2.1M/P Progressive Colour CMOS Image Sensor,
1920x1080 30fps

• Supports Various Digital Video Outputs

720p60, 720p50, 1080p30, 1080p25

• Video Outputs

Primary HD-SDI (BNC)
Test/Setup TV Out (Test Point-adapter to BNC included), NTSC/PAL selectable

• OSD Menu for Setup and Configuration

• Lens Control

DC Iris

• Power Source

DC12V/AC 24V (Dual Power Model)

DC12V (DC Only Power Model)

7

4. EQUIPMENT AND ACCESSORIES

HD CCTV
Digital Video Camera

Auto Iris Lens
Connection Plug

C-Mount Adapter Ring

Operation Manual

8

+ -

*

NOTE

PLEASE REMOVE PROTECTIVE FILM

5. CAMERA COMPONENT DESCRIPTIONS

• FRONT

9

TRIPOD MOUNTING HOLE (1/4"-20 UNC)

TRIPOD MOUNTING HOLE (1/4"-20 UNC)

C-MOUNT ADAPTER RING

MOUNT COVER

CS-MOUNT ADAPTER RING

CS-MOUNT ADAPTER RING FIXING SCREW (2EA)

AUTO
IRIS JACK

10

5. CAMERA COMPONENT DESCRIPTIONS

• BACK

①. MENU BUTTON
②. UP BUTTON
③. DOWN BUTTON
④. LEFT BUTTON
⑤. RIGHT BUTTON
⑥. POWER LED

(The LED turns on when power is supplied)

⑦. VIDEO OFF/ON SWITCH
⑧. HD SDI OUTPUT JACK
⑨. VIDEO OUT JACK

(Used to connect an external video monitor in jack)

⑩.POWER TERMINAL

(Used to connect an DC12V power source)
(Option: AC24V/DC12V)

➊ ➋ ➎ ➐

➌

➓

➍

➑

➒

➏

DC12V

MENU/SETMENU/SET

VIDEOVIDEO

OFF/ONOFF/ON

POWERPOWER

HD SDI

OUTPUT

HD SDI

OUTPUT

DC12V/AC24V

➊ ➋ ➎ ➐

➌

➓

➍

➑

➒

➏

VIDEOVIDEO

AC24V/DC12V

DC12V GND

+ -

6. INSTALLATION

• LENS CONNECTION

Mega Pixel Lenses are sold separately. Lenses such as an Auto Iris Lens,
CS-Mount lens and C-Mount lens can be used (adapter included for C-Mount Lens).

NOTE

• Please keep the lens clean.

• Any foreign objects and fingerprint marks on the lens can cause

inferior image quality, especially in low light level conditions

.

When Using an Auto Iris Lens

1. Strip off about 8mm of the outer jacket of the auto iris lens cable.

2. Strip off about 2mm each of the insulated conductors

inside the lens cable.

11

6. INSTALLATION

3. Remove the cover of the auto iris lens connection plug and

solder the lens cable to the connector pins inside the plug.

* PIN ASSIGNMENT OF THE LENS CONNECTOR

1) Video Auto Iris Lens
Pin 1: Power source (DC 12V)
Pin 3: Video signal
Pin 4: Shield, GND (Ground)

2) DC Auto Iris Lens
Pin 1: DAMP- (CTL-)
Pin 2: DAMP+ (CLT+)
Pin 3: DRV+
Pin 4: DRV- (GND)

4. Replace the auto iris lens connection plug cover and take off the sensor

protection cap then attach the auto iris lens to the camera by screwing it in
clockwise.

12

6. INSTALLATION

5. Insert the connection plug from the auto iris lens cable into the auto

lens connector, which is located on the side of the camera.

13

C-mount lens: 10 mm or less
CS-mount lens: 5 mm or less

* NOTE

Use the lens under the specification as shown.
Otherwise the lens can damage the camera or
abnormal fixing may result.

6. INSTALLATION

Installation of C-Mount Lens

Installation of CS-Mount Lens

14

CS-MOUNT ADAPTER RING

CS-MOUNT ADAPTER RING

C-MOUNT ADAPTER RING

MENU/SET

VIDEO

OFF/ON

POWER

HD SDI

OUTPUT

VIDEO

DC12V/AC24V

MENU/SET

VIDEO

OFF/ON

POWER

HD SDI

OUTPUT

DC12V GND

VIDEO

+ -

6. INSTALLATION

• MONITOR CONNECTION

15

CAUTION

When you output Video

WDR function does not work

DC12V/AC24V REGULATED
POWER SUPPLY

HD SDI INPUT

HD SDI INPUT

SDI
RECEIVER
DISPLAY
DEVICE

SDI
RECEIVER
DISPLAY
DEVICE

TV
MONITOR

TV
MONITOR

VIDEO INPUT

VIDEO INPUT

BNC FEMALE
VIDEO OUTPUT

BNC FEMALE
VIDEO OUTPUT

HD SDI OUTPUT

HD SDI OUTPUT

DC12V REGULATED
POWER SUPPLY

- DC12V

- DC12V/AC24V

7. DIMENSIONS

Unit(mm)

16

86.1 (C-MOUNT)

81.1 (CS-MOUNT)

58

58

75.5 (C-MOUNT)

70.5 (CS-MOUNT)

TRIPOD MOUNTING HOLE

(1/4"-20 UNC, Depth 5)

TRIPOD MOUNTING HOLE

(1/4"-20 UNC, Depth 5)

8. SPECIFICATION

Image Device SONY 1/3” 2.1MP Progressive Colour CMOS Image Sensor

Effective Pixels 1984 (H) x 1105 (V) 30fps

Unit Cell Size 2.8um (H) x 2.8um (V)

Video Output Mode

HD-SDI: 720p60, 720p50, 1080p30, 1080p25

TV Out: NTSC / PAL Selectable

Minimum Illumination 0.1 Lux

S/N Ratio More than 50dB

Shutter Speed Auto / Manual Selectable

Manual Shutter Speed

1/30 (25), 1/60 (50), 1/120 (100), 1/240, 1/500,

1/1K, 1/2K, 1/4K, 1/8K, 1/16K, 1/30K, 1/60K

Controllable Max. Gain 29dB

White Balance AUTO / AUTOext / PUSH / MANUAL

Lens Control DC Iris

OSD Menu Yes

Power
Consumption

DC DC12V(±10%), Max. 200mA

DUAL

DC12V(±10%), Max. 270mA

AC24V(±10%), Max. 3.6W

Weight DC12V: 175g, DUAL: 200g

Dimension 58(W) x 58(H) x 70.5(D)

Conformity CE, FCC, KC

Temperature / Humidity
(Non Condensing)

Operation: -10~50 Deg. C / 20~80%

Storage: -20~70 Deg. C / 20~95%

Specifications and designs are subject to change for improving the

functionality of this product without notice.

17

9. OSD MANUAL

• Menu Structure

SETUP

EXPOSURE

WHITE BALANCE

WDR / BLC

DNR

DAY & NIGHT

IMAGE

SPECIAL

SYSTEN

RESET DATA ALL

EXT

Main Sub Menu Sub Menu

EXPOSURE

BRIGHTNESS 0 ~ 20
AE MODE NORMAL AE / INDOOR
LENS(IRIS) MANUAL / AUTO

SHUTTER

MANUAL /
AUTO

LEVEL

1/30 (25), 1/60 (50), 1/120 (100), 1/240, 1/500,
1/1K, 1/2K, 1/4K, 1/8K, 1/16K, 1/30K, 1/60K.

RETURN BACK / EXIT
DSS OFF, X2, X3, X4.
AGC 0 ~ 10
BASE FREQ 60Hz / 50Hz
RESET DATA BACK / DEF.
RETURN BACK / EXIT.

WHITE

BALANCE

WB MODE

AUTO
/AUTOext
/PUSH
/MANUAL

COLORTEMP. LOW / MIDDLE / HIGH

R-GAIN 0 ~ 20

B-GAIN 0 ~ 20

RETURN BACK / EXIT
SATURATION 0 ~ 20
RESET DATE BACK / DEF.
RETURN BACK / EXIT.

WDR / BLC

MODE OFF, WDR, BLC, D-WDR

WDR WGT 0 ~ 4
BLC OSD OFF ~ ON
BLC POS-X 0 ~ 20
BLC POS-Y 0 ~ 20
BLC SIZE-X 0 ~ 20
BLC SIZE-Y 0 ~ 20
RESET DATA BACK / DEF.
RETURN BACK / EXIT.

DNR OFF, LOW, MIDDLE, HIGH

DAY &

NIGHT

COLOR/
B&W/
AUTO

D&N DETECT AGC

DELAY 1sec, 3, 5, 10, 15, 20, 25, 30, 40, 50, 60sec

D->N LEVEL 3 ~ 20

N->D LEVEL 0 ~ 16

RESET DATA BACK / DEF.

RETURN BACK / EXIT.

18

9. OSD MANUAL

Main Sub Menu Sub Menu

IMAGE

SHARPNESS 0 ~ 20
GAMMA 0 ~ 4
FLIP OFF, H FLIP, V FLIP, HV FLIP
LENS SHADING OFF, ON
DZOOM 1x, 2x, 4x, 6x, 8x, 10x, 12x, 14x, 16x, 18x, 20x
RESET DATA BACK / DEF.
RETURN BACK / EXIT.

SPECIAL

PRIVACY OFF / ON

ZONE NO 0 ~ 23
ZONE OP OFF / ON
X-POS 0 ~ 60
Y-POS 0 ~ 40
X-SIZ 0 ~ 40
Y-SIZ 0 ~ 40

COLOUR

BLK, WHT, YEL, CYN, GRN,

MAG, RED, BLU
TRANS. 0 ~ 4
RESET DATA BACK / DEF.
RETURN BACK / EXIT.

HLMASK OFF / ON

LEVEL 0 ~ 20

COLOUR

BLK, WHT, YEL, CYN, GRN,

MAG, RED, BLU
RESET DATA BACK / DEF.
RETURN BACK / EXIT.

PATTERN OFF / 0 / 1
RESET DATA BACK / DEF.
RETURN BACK / EXIT.

SYSTEM

SDI FORMAT 1080P / 720P
SDI FPS 30 (60) / 25 (50)

CVBS FORMAT

NTSC /
PAL

CVBS OUT AUTO / OFF / ON (WDR OFF)
CVBS VIEW CROP / FULL
RETURN BACK / EXIT.

APPLY OK / ON

SYSTEM INFO.

S/W VERSION
SET VERSION
RETURN BACK / EXIT.

REBOOT
RETURN BACK / EXIT.

19

9. OSD MANUAL

• Function Description

0. SETUP

- EXPOSURE : Go sub menu for camera exposure control.

- WHITE ALANCE : Go sub menu for camera white balance control.

- WDR/BLC : Go sub menu for camera WDR or BLC action.

- DNR : Control noise reduction setting.

- DAY & NIGHT : Go sub menu for camera day & night control.

- IMAGE : Go sub menu for adjust image functions.

- SPECIAL : Go sub menu for special feature control.

- SYSTEM : Go sub menu for system control & information.

- RESET DATA ALL : Reset all the cameras feature data to the default values.

1. EXPOSURE

- BRIGHTNESS : Adjust image brightness value.

- AE MODE : Adjust AE control mode.

- LENS(IRIS) : Select lens iris control type.

- SHUTTER : Select shutter speed control type.

• LEVEL : Adjust shutter speed at manual shutter mode.

- DSS : Adjust digital slow shutter control level.

- AGC : Adjust max. gain level for brightness control.

- BASE FREQ : Select basic control frequency for control camera feature.

2. WHITE BALANCE

- WB MODE : Select white balance control mode.

• AUTO : Full auto control mode in colour temperature range 2300K~10000K.

• AUTOext : Extended auto mode for special illumination.

• PUSH : Enables fixing the control settings for a specific environment.

Push & release, for fixing WB control setting.

• MANUAL : Enable WB control setting in manual mode.

◦

COLOR TEMP. : Select colour temperature range for WB control in manual mode.

◦

R-GAIN : Adjust red colour gain for WB control in maual mode.

◦

B-GAIN : Adjust blue colour gain for WB control in manual mode.

- SATURATION : Adjust colour saturation level.

3. WDR/BLC

- MODE : Select WDR / BLC mode.

• WDR : Operate in Wide Dynamic Range mode. Controlled video frame rate.

• BLC : Operate in Backlight Compensation mode.

• D-WDR : Digital wide dynamic range control.

20

21

9. OSD MANUAL

- WDR WGT : WDR weight control level setting in WDR mode.

- BLC OSD : Display BLC control zone on screen.

- BLC POS-X : Select BLC control zone vertical position.

- BLC POS-Y : Select BLC control zone horizontal position.

- BLC SIZ-X : Select BLC control zone vertical size.

- BLC SIZ-Y : Select BLC control zone horizontal size.

4. DNR: Reduce image noise

5. DAY & NIGHT

- MODE : Select TDN (True Day & Night control) mode.

• AUTO : Camera controlled automatically to decide day or night environment
using AGC calculation data or input level data from CDS sensor.

• COLOR : Fix the mode to a daytime environment setting.
Video image operates in colour.

• B&W : Fix the mode to a nightime environment setting.
Video image operates in B/W.

■

D/N DETECT : Fixed selection of AGC for TDN auto control.

■

DELAY : Delay changeover time between day or night mode in Auto mode.

■

D->N LEVEL : Threshold level for changing from Day to Night mode.

■

N->D LEVEL : Threshold level for changing from Night to Day mode.

6. IMAGE

- SHARPNESS : Adjust image sharpness level.

- GAMMA : Gamma curve select.

- FLIP : Vertical & Horizontal flip setting.

- LENS SHADING : Enable lens shading compensation.

- DZOOM : Select digital zoom magnification.

7. SPECIAL

- PRIVACY : Setting for protecting private areas in an image using mask setting.

• ZONE NO. : Select private mask zone number.

• ZONE OP. : Select zone mask display On/Off.

• X-POS : Select zone horizontal position.

• Y-POS : Select zone vertical position.

• X-SIZ : Select zone horizontal size.

• Y-SIZ : Select zone vertical size.

• COLOR : Select mask colour

• TRANS. : Select mask transparency level.

22

9. OSD MANUAL

- HLMASK : Mask image highlight area.

• LEVEL : Select highlight level.

• COLOR : Select mask colour.

- PATTERN : Colour bar display select.

8. SYSTEM

- SDI FORMAT : 1080P / 720P

- SDI FPS : 30 or 25 fps in 1080p mode.
60 or 50 fps in 720p mode.

- CVBS FORMAT : NTSC / PAL

• CVBS OUT : Select mode for CVBS out action.

◦

ON, OFF : Enable or Disable CVBS out data.

◦

AUTO : Check automatically CVBS video cable connection.

If connected, CVBS out data is enabled and WDR mode
is set to off automatically.

• CVBS VIEW : CVBS out video angle setting.

◦

CROP : Cut the scene outer area to keep image aspect ratio.

◦

FULL : Fill the full angle scene into image with

H-V size & ratio change.

- APPLY : Apply all video angle setting.
Use the set button to apply.

- SYSTEM INFO.

• S/W VERSION : Camera’s basic software version.

• SET VERSION : Camera’s feature control setting version.