Page 1
29
SECT 9—PROGRAMMING REMOTE CONTROLS
FOR HELP-GENIECOMPANY.COM
Fig. 9-1
Moving door can cause serious injury or death.
• Keep people clear of opening while door
is moving.
• Do not allow children to play with
remote controls.
If Safety reverse does not work properly:
• Close door and disconnect operator using
emergency release.
• Do not use door operator, remote controls,
or wireless keypad.
• Refer to door and door operator owner’s
manuals before attempting any repairs.
WARNING
PROGRAMMING REMOTE CONTROLS
NOTE: Remote controls will not close door if
Safe-T-Beam® malfunctions.
NOTE: When programming remote control, it must
be at least 24 inches from the antenna.
1. Program one button remote
.
• Lower lens cover.
• Locate learn code button and learn indicator on
power head Fig. 9-1
.
•
Press and release learn code button.
–
Red learn indicator blinks 2 times per second.
•
Press remote control button once within
30 seconds.
– Red learn indicator stays lit.
• Press remote control button again.
– Red indicator goes out and memory
is stored.
NOTE: If red indicator blinks approximately 4
times per second, programming has stopped.
If programming stops, repeat above steps.
2. Program multi-button remote
.
• Repeat step 1 above “Program one-button
remote” for each button and operator.
NOTE: Each button on a multi-button remote
control is for a different operator.You cannot use
more than one button on a multi-button remote for
a single door.
3. Operating remote
.
• Press button once:
– If door is at up or down limit, door will move
away from that limit.
– If door is stopped between limits, it will move
toward the limit where it was last stopped.
– If door is moving, it will stop.
NOTE: Door automatically stops at end of open or
close cycle.
NOTE: Each remote device must be
programmed separately
Learn Button
Learn Indicator
To erase all receiver memory, such as
following loss of remote, home sale or
tenant turn-over.
• Press and hold learn code button for
10 seconds or until learn code
indicator goes out—memory is erased.
• Program remotes as before.
FCC and IC CERTIFIED
This device complies with FCC Part 15 and RSS
210 of Industry Canada. This equipment has been
tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide
reasonable protection against harmful interference
in a residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not
occur in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
• Re-orient or relocate the receiver antenna.
• Increase the separation between the operator
and receiver.
• Connect the operator into an outlet on a circuit
different from that to which the appliance
is connected.
• Consult the dealer.
GENIE GIT-1, GIT-2, GIT-3
Page 2
SETTINGS
(CONTACT REVERSE) FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM
Fig. 7-3
Limit switch adjustments must be completed
before running contact reverse test.
1. Test contact reverse.
• Open door using wall control.
• Lay 2" x 4" board
*
on floor in center of garage
door opening. Fig. 7-3
.
• Close door using wall control.
– Door should stop and reverse
within 2 seconds of contacting the board.
– If door does not reverse properly:
a. Decrease closing force a small amount
by turning the “CLOSE” force adjustment
screw slightly counterclockwise.
b.
Test contact reverse again.
c. Repeat steps a. and b. until contact
reverse works properly.
*If you don’t have a 2" x 4" board handy, any object
1-1/2 inches high that can withstand being hit by the
garage door without sustaining damage is fine.
NOTE: If door is
stopping but not reversing,
“CLOSE” limit switch must be moved closer to
door.
SECT 8—BATTERY & VISOR CLIP
FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM
Visor Clip
Battery
Battery
Cover
1. Install/replace battery Fig. 8-1.
• Using a pen or similar object, gently push in
on tab.
• Cover snaps open. Remove old battery.
• Observe polarity markings (+,-) inside
battery compartment.
• Match new battery to polarity markings and
instal new A23, 12 Volt battery.
• Replace battery cover.
NOTE: Use only A23, 12 Volt battery.
2. Attach visor clip Fig. 6-1
.
• Slide clip in slot on back of remote control.
– Snap in place.
Model
Number
Fig. 8-1
Loading...