Genie Wireless Keypad, DIGITAL WIRELESS KEYPAD Operating Instructions Manual

STEP 1:

S

ETTING YOURWIRELESS KEYPAD PIN

(PERSONALIDENTIFICATIONNUMBER)

A Activate programming mode.

• Press (in order) .

– Red LED blinks -once per second.

• Enter your PIN (3 to 8 characters).

• Press .

– Red LED blinks - twice per second and turns off.

STEP 1:

S

ETTING YOURWIRELESS KEYPAD PIN

(PERSONALIDENTIFICATIONNUMBER)

A Activate programming mode.

• Press (in order) .

– Red LED blinks -once per second.

• Enter your PIN (3 to8 characters).

• Press .

– Red LED blinks - twice per second and turns off.

3

DEF

1

2

4 5 6

7

8

9

0

GHI

JKL

MNO

PQRS

TUV

WXYZ

9V

OF U.S. & IMPORTED PARTS

This Wireless Keypad is compatible with all INTELLICODE® radio equipped GENIE® produc ts.

• Drill with 1/16" Drill Bit

• Phillips Screwdriver

• Pencil

• Mounting Screws INCLUDED inside

Battery Compartment

Interchangeable
Flip-up Cover
available in 3
optional Classic
Colors to match
your home’s
exterior decor

Red LED
indicates
Battery Power
and Status
during Use
and Programming

Backlit Keypad
for Ease of Use
atNight

Battery
Compartment
9 Volt Battery
(included)

Instructions

• Ability to Control up to three

Genie® INTELLICODE® Openers

• Simple to Program and Install

• PIN Codes can be up to 8 Characters

• Low Battery Power Indicator

• Stays Programmed During

Battery Change

• Temporary PIN for Special Purpose Access

OPERATING INSTRUCTIONS

(KEEP FOR FUTURE REFERENCE)

A Moving Door can cause serious injury or death.

1 Keep people clear of opening while Door is moving.
2 Do

Not allow children to play with Wireless Keypad.

3 During programming, the Door Opener could begin to run, so stay away from

the moving Door and its parts.To keep the Door from moving, close the Door
and disconnect it from the Opener by pulling the Emergency Release Cord.

3528135717

WARNING

STEP 3:

O

PERATING ONE DOOR OPENER

A To move the Garage Door.

• Enter your PIN.

• Press .

STEP 2:

P

ROGRAMMING ONE DOOR OPENER

A Find the Learn Code Button and Learn Code

Indicator LED on your door opener.

– If your Door Opener has a

black Antenna Wire,
the LearnCode Button
and Indicator LED
are located near the Antenna.
(The Light Lens may need
to be opened.)

– If your Door Opener does not

have an Antenna,
you have an External Receiver.
The External Receiver cover
must beremoved to access
the Learn Code Button
and Indicator LED.

• Press the Learn Code Button.

–

Learn Code Indicator LED (on Opener) will blink.

• Enter your PIN and press on Keypad.

– Learn Code Indicator LED stays on.

• Press again.

– Learn Code Indicator LED turns off.

• Press again.

– Door moves.

BASIC PROGRAMMING FOR

ONE DOOR OPENER

Red Indicator
LED

Learn
Code
Button

Located
on Opener
Housing

STEP 3:

P

ROGRAMMING DOOR OPENERS

A Decide which Door will be Door #1,#2 and #3.

• Press the Learn Code Button (see Section 1 Step 2).

– Learn Code Indicator LED (on Opener) blinks.

• Enter your PIN and press on Keypad.

– Learn Code Indicator LED stays on.

• Press the number you have picked for this

Door Opener ( or or ).

– Learn Code Indicator LED stays on.

• Press .

– Learn Code Indicator LED turns off.

B Repeat step A above for each Door Opener.

Each Door Opener must be programmed to receive the
signal from the Wireless Keypad.

STEP 4:

OPERATING 2OR 3 DOOR OPENERS

A To move one of the Doors.

• Enter your PIN.

• Press .

• Press Door Opener number ( or or ).

SEE NOTE AT BOTTOM OF SECTION 1
Proceed to Section 3 - Mounting Instructions.

PROGRAMMING FOR
2 OR 3 DOOR OPENERS

MOUNTING INSTRUCTIONS

The Keypad must be mounted in sight of the Door(s), at
least 5 feet above the ground and clear of any moving
Door parts.

A Mount Keypad. (Mounting screws located inside

Battery Compartment.)

• Remove Battery Cover (See Section 4 Figure 2).

•

Drill a 1/16”pilot hole for the top mounting screw.

• Install a screw into the drilled
hole,leaving a 1/8" gap
between the screw head
and the wall. See Figure 1.

• Hook the Keypad over
the screw.

• Mark,drillpilot hole and
fas

ten bottom screw.

• Reinstall Battery Cover.

For answers to questions, call 1-800-35 GENIE, or visit
www.geniecompany.com

Additional Genie® products can be ordered using the Accessories
page in your Owner’s Manual or through the 800 numb er above.

FOR CONVENIENCE

Program Keypad BEFORE mounting.

SECTION

1

SECTION

2

SECTION

3

ADDITIONAL OPERATIONS

SECTION

4

USINGA TEMPORARY PIN

A temporary PIN allows temporary access to your home by
repair persons, meter readers, etc.if you so desire.

A

Enter your PIN.

•

Press .

B

Enter the Temporary PIN (from 3 to 8 characters).

• Press .

NOTE

•

DONOT reprogram the Door Opener(s).

•

Temporary PIN remains active until the next time your
normal PIN is entered.

FORGOT YOUR PIN

OR

C

HANGINGYOUR PIN

A Erase old PIN.

• Press and hold in order -

.

– Red LED will blink onceand turn off.

• Release all buttons.

B Programming Door Opener(s).

• Return to“Programming” (Section 1 or Section 2).

Wall

screw head gap

Figure 1

FOR CONVENIENCE

Program Keypad BEFORE mounting.

STEP 2:

P

ROGRAMMING THE KEYPAD FOR

MULTIPLE DOOR OPENERS

A All Door Openers will use the same PIN.

• Enter your PIN and press .

– Red LED blinks - once per second.

• Press again.

– Red LED blinks - twice per second.

• Press the number of Doors (total) you wish

to control ( or ).

• Press .

– Red LED blinks several times and turns off.

Program
Button

FEATURES :

T

OOLS NEEDED:

If Safety Reverse does not work properly:

1 Close Door and disconnect the Opener using Emergency Release Cord.
2 Do not use Door Opener,Remote Controls, or Wireless Keypad.
3 Refer to Door and Door Opener Owner’s Manuals before attempting any repairs.

1"
8

Printed in the U.S.A.

©2005 The Genie Company, D.B.A. GMI Holdings, Inc.

FCC and IC CERTIFIED

This device complies with FCC Part 15 and RSS 210 of Industry Canada.This equipment has been tested and
found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules.These limits are
designed to provide reasonable protection against harmful interference in a residential installation.This
equipment generates,uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However,there is no guarantee
that interference will not occur in a particular installation.If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on,the user is
encouraged to try to correct the interference by one or more of the following measures: 1. Re-orient or
relocate the receiver antenna. 2. Increase the separation between the opener and receiver. 3. Connect the
opener into an outlet on a circuit different from that to whichthe appliance is connected. 4.Consult the dealer.
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to
operate the equipment.

CHANGING BATTERY

If the red LED does
not blink during use,
the battery needs to
be changed.

1

2 3

4 5 6

7

8

9

0

DEF

GHI

JKL

MNO

PQRS

TUV

WXYZ

PROG

Battery

Press here

Figure 2

Bottom
Mounting
Screw

Red LED

Covers available in:

• Brown - P/N 35365R

• Almond - P/N 35365S

• Sandstone - P/N 35365T

Proceed to Section 3 - Mounting Instructions.

NOTE

•

If the Door does not move,check the red LED on
Keypad. If the LED is blinking rapidly,the PIN was
entered incorrectly. After the LED stops blinking,
re-enter your PIN and try again.

•

Any Keypad Button will control the Door for 30 seconds
after the Door starts moving.

•

Rapid blinking of the red LED indicates an error. After a
few seconds the LED will turn off. Start over.

Wait until Keypad Backlight turns off (approximately 30 seconds).

Wait until Keypad Backlightturns off (approximately 30 seconds).