Genie 3681036666 User Manual 2

Operation and Maintenance Manual

3681036666

GARAGE

TABLE OF CONTENTS

Warranty Information ................... 2

Safety Information ..................... 3

Safety Features ......................... 3

Important Installation Instructions ....... 3

Pre-lnstallation Checklist .............. 4-6

Adjustments .......................... 7-8

Programming the Remote Control ...... 8

Installing lightbulb and lens ............. 9

Scheduled Maintenance ............... 10

Troubleshooting Guide ............. 10-11

Wiring Diagram ........................ 12

Parts Lists and Exploded Views ..... 12 -13

Accessories ............................ 14

COMPLETE WiTH INTELLICODE ®

REMOTE CONTROL AND SERIESII

ELECTRONICS

For 7' 6" Doors. Extension Kit is available for 8' Doors
Included Wall Control MUST be installed prior to Operation

of this Garage Door Operator.
Safe-T-Beam ®Safety Reverse System Must be installed and

the Force Controls MUST be Properly Set to close door.
This Equipment meets or exceeds all Federal, State and UL 325

Safety Requirements.

Having Difficulty? Need Help?

Please call us:1-800-35-GENIE (354-3643)
www.geniecompany.com

Please have Model information ready when calling.

THE GENIE COMPANY LiMiTED WARRANTY

What is covered?

Any defect in material and product workmanship from personal, normal

household usein accordance with the Owner's Manual.
For how long?

MODEL2020LSeries... 10 yearson motor and 2 yearson all other parts.

Who gets the warranty?

This warranty islimited to the consumer who originally purchased
the product.

Geographic scope:

This warranty applies only to units installed and operated within the country
where they were purchased.

Limitations:

IMPLIEDWARRANTIES,INCLUDINGTHOSEOF FITNESSFORA PARTICULAR
PURPOSEANDMERCHANTABILITY(AN UNWRITTENWARRANTYTHATTHE

PRODUCTISFITFORORDINARYUSE),ARELIMITEDTO ONEYEARFROMTHE
DATEOFPURCHASE.GENIEWILL NOTPAY FOR:LOSSOFTIME;

INCONVENIENCE;LOSSOFUSEOFYOURGENIEPRODUCTORPROPERTY
DAMAGECAUSEDBYYOURGENIEPRODUCTORITSFAILURETOWORK;ANY

SPECIAL,INCIDENTALORCONSEQUENTIALDAMAGES;OR ANYDAMAGES

RESULTINGFROMMISUSEORMODIFICATIONOFYOURGENIEPRODUCT.

Some states and provinces do not allow limitations on how long animplied
warranty lastsor the exclusion of incidental or consequential damages, so the

above limitations or exclusions may not apply to you.
This warranty isthe only one we will giveon your Genie product, and it sets

forth all our responsibilities regarding your Genieproduct.There are noother
express warranties.

State and province rights: This warranty gives you specific legalrights, and
you may also haveother rights which vary from state to state andprovince to

province.

How to get warranty service:

To obtain warranty servicefor your Genie product, you must provide proof of
the date and place of purchaseof the product.

1.Do=it-Yourself-Service.
Callthe GenieCustomer Servicetoll free at 1.800.354.3643to speak in

person to a trained Genie representative for assistancein diagnosing the
problem and arranging to supply you with the required parts for do-it-

yourself repairs.Trained service representativesare available Monday-Friday,
8:00a.m.- 9:00 p.m., EasternTime, and on Saturday, 10:00a.m. to 7:00 p.m.,

EasternTime (subjectto holidays) You may alsoget the information you
needat www.geniecompany.com.

2.Service From Authorized Dealers.

YoualsomayobtainwarrantyservicefromGenieauthorizeddealersbycallingthe
GenieCustomerServiceat 1.800.354.3643or byvisitingwww.geniecompony.com

beforeschedulingwarrantyservice.If warrantyserviceisprovidedbyanauthorized

dealer,Geniewill provideallrequiredpartsunderwarrantyatnochargeto you,but
thedealersareindependentbusinesspeopleandmayrenderabenchor servicecall

chargefortheir services.Geniewill notreimburseyouorotherwiseberesponsiblefor
thosecharges.

Wesuggestthat youretainyouroriginalpackingmaterialintheeventwechoose
to repairor replaceyour GenieProductand requestthat youshipit to us.Besureto

includeyourname,address,telephonenumber,proof ofdateand placeofpurchase
andadescriptionofthe operatingproblem.After repairingorreplacing,yourGenie

product,wewillshipit toyourhomeatno costto youfor partsandlabor,butyouwill
haveto payaminimumof $S.00forshippingand handlingcharges.

Yourchoiceof eitheroneofthe above-describedserviceoptionsisyourexclusive

remedyunderthiswarranty.
What this warranty does not cover:
Thiswarrantydoesnotcoverbatteries(whichareconsideredreplaceableparts),

installation,commercialuse,defectsresultingfromaccidents,damagewhileintransit

to our servicelocationordamageresultingfromalterations,misuseorabuse,lackof

propermaintenance,unauthorizedrepairormodificationoftheproduct,affixingof

anyattachmentnotprovidedwith theproduct, programmingofthe RemoteControl

Devices,Safe-T-Beam®adjustment/cleaning,staplesthrough wiring, pinchedor broken

wires,Carriagedisengaged,ForceControladjustments,door outof balance,broken
springsorcables,poweroutages,useofextensioncords,missingordamagedpartson

discounted,clearanced,finalsaleor tapedcartons,phantomoperations(laborisnot
coveredif Openerisfunctioning properlywhiletechnicianisin garage),fire,flood,or

actsofGod,orother failuretofollow theOwner'sManual.

Pleasenote the following information,soit is availableifyou
needto call us.

DatePurchased / /
SerialNumber*

Operator Model*
Dealer Name

DealerAddress
City

State / Zip

eeSerial Number is located on the Power Head, inside

the Light Cover.

WK YR P I'_

Serial/Mfg No.

NOTE

Pleasekeep original or photocopy of your salesreceipt

with this manual for future reference shouldservice

ever be required.

INCLUDED IN THIS PACKAGE

Manual 1)Warranty Information

2) Pre Installation Checklist to be reviewed
prior to any assembly or installation

3) Necessary Adjustments

4) Programming Remote Devices

5) Maintenance and Troubleshooting

6) Parts Explosions

7) Accessory Order Form

8) Door Opener Association Safety and

Maintenance Brochure (DASMA)

9) Entrapment Warning Label- To be Adhered

in close proximity to wall control

Poster 1) Pictorial and step by step opener assembly

instructions

2) Pictorial and step by step opener installation

instructions

MARKED CLEARLY IN BOTH THE MANUAL

lAND POSTER ARE READ, UNDERSTOOD AND

FOLLOWED;

Visit Our Website at: www.geniecompany.com

FORANSWERS:CALL1.800.354.3643

SAVE THESE INSTRUCTIONS

2 For Help, call 1=800-3S-GENIE or visit www.geniecompany.com

OVERVIEW OF POTENTIAL HAZARDS

Overhead doors arelarge,heavy objects that move with the help of springsunder high tension and electric motors. Sincemoving objects,springs

undertension, and electric motors cancauseinjuries, your safetyand the safety of others depend on you reading the information in this manual. Ifyou
havequestions or do not understand the information presented, callTheGenie Company. or your local GenieDistributor.

In this section, and those that follow, the words Danger, Warning and Caution are used to emphasize important safety

information. The word:

DANGER: indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING: indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION: indicates a potentially hazardous situation which, if not avoided, may result in injury or property damage.

The word NOTE is used to indicate important steps to be followed or important considerations.

POTENTIAL HAZARD

MOVING DOOR

ELECTRICALSHOCK

Could result in death

HIGH SPRINGTENSION

EFFECT PREVENTION

WARNING: . Keep people clear of opening while door is moving.

Could result in death oDo Not allow children to play with the door operator.

or serious injury, oDo Not operate a door that jams or one that has a broken spring.

WARNING:

Could result in death

or serious injury.

WARNING:

or serious injury.

oTurn off power before removing operator cover.
oWhen replacing cover, make sure wires are not pinched or near

moving parts.

oOperator must be properly grounded.
. Do Not try to remove, repair or adjust springs or anything to

which door spring parts are fastened, such as, wood blocks,
steel brackets, cables or other like items.

oRepairs and adjustments must be made by a trained door

system technician using proper tools and instructions.

MPORTANT INSTALLATION
NSTRUCTIONS

WARN ING:

TO REDUCE THI RISK

OF SEVERE INJURY OR DEATH:

1 READAND FOLLOWALL SAFETY,INSTALLATIONAND OPERATION

INSTRUCTIONS.If you have any questions or do not understand

an instruction, call your authorized Genie installation professional.

2 Do Not install operator on an improperly balanced door. An

improperly balanced door could cause severe injury. Repairs and
adjustments to cables, spring assembly, and other hardware
must be made by a trained service person using proper tools

and instructions.

3 Remove all ropes, and disable all locks connected to the door

before installing operator.

4 Install door operator 7 feet or more above the floor. Mount the

emergency release knob 6 feet above the floor.

5 Do Not connect the operator to the source of power until

instructed to do so.

6 Locatethe control button:

• Within s!ght of door.

• At a minimum height of Sfeet, so small children cannot reach it.

• Awayfrom all moving parts of the door.

7 Install the entrapment WARNING label next to the wall button or

console. Install the emergency releasetag on, or next to, the
emergency release.

8 The operator must reverse when the door contacts a 1-1/2 inch

high object on the floor at the center of the doorway. This is

about the size ofa 2 x 4 board aid fat.

SAFETY FEATURES

Safe-T-Beam® (STB)Non-Contact
Reversing System

Placesan invisiblebeam acrossdoor opening, that
reversesthe door during down travel to the fully

open position if anything passesthrough beam.

Safe-T-Reverse® Contact Reversing System

Automatically stops and reversesa closing door
within 2 secondsof contact with an object.

Safe-T-Stop® Timed Reversed System

Automatically opens a closing door, ifdoor does not
close within 30seconds.

ForceGuard Control

Used to set the force required for opening and clos-
ing door. Formaximum safety,set the minimum

force required to fully open and close door.
Automatic Lighting System

Light bulbs up to 60 Watts max., used for safer
entries and exits. The lights turn on when door

isactivated and automatically turn off 4.5
minutes later.

Manual Emergency Release

Allows the garage door to be opened or closed

manually for emergencies or maintenance.

For Help, {all 1-800-35-GENIE or visit www.geniecompany.com :3

PRE=INSTALLATION CHECKLIST

This Opener includes parts and supplies needed to install in most
garages and connect to most garage doors. There are many variations

of garagesand garage doors. A few additional parts and supplies may

be needed to install Opener into your garage and connect to your

garage door. While checking items listed below, note any additional
items you will need.

Tools used in this section:

• 12% Tape Measure • Pencil • Ladder • Level

C Checkdoor type. Makeanoteofwhetheritisasectionalora
one-piece door for reference later (Figure 2).

SECTIONAL DOOR,TORSION SPRINGS SECTIONAL DOOR, EXTENSION SPRINGS

ONEPIECEDOOR,TRACKLESS

Header Area

Check following items before assembling Opener:

Checkcondition of vertical stilein center of door, and its connection to
door's top and bottom beams. (Figure 1)
A Ifdoor frame is nailed together and not a solid connection, door

frame must be bracedor reinforced before installing Opener.
B If door is"lightweight" (madewith frame and skin - not solid),

door (including door frame) must be braced or reinforced before

installing Opener.
C Adoor opener reinforcement bracket may alsobe needed to

connect garage door to Opener's Door Bracket. This Opener is
designed for installation on a properly braced sectional door or

solidly braced one-piece door.
D Contact your Genie FactoryAuthorized Dealeror dealer of your

garage door for any necessarybracing and a door opener
reinforcement bracket (if needed) before proceeding.

E If you haveawooden door, measuredoor's thickness. If your door
is lessthan 2" thick, brace door or useshorter Door Bracket LagScrews

(1/4" x 1-1/4"- not included)

AND BALANCE

A Raisedoor, check alignment and seeif it movesfreely (Figure 2).

Ifdoor appears out of alignment, binds, or does not move smoothly,
contact aGenieFactory Authorized Dealer or dealer of your garage

door for repairsand adjustments to door mechanism.
B Raisedoor to 3' - 4' above ground and carefully let go. Door

should staystationary. Slight movement isacceptable. More than
slight movement meansdoor is out of balance. Contact a Genie

FactoryAuthorized Dealer or dealer of your garage
door for repairsand adjustments to door mechanism.

....::::-:::::: KEEPFEET CLEAR OF DOOR

One-Piece
Door

Figure 2 Checking door balance

Center Stile

Figure 1 Note Door Type

A Measuredoor height (floor to top of door) using a tape measure.

B This new Garage Door Opener isdesigned for doors up to and
including 7' 6" tall. Ifdoor height is7' 6" or lesscontinue to CheckStep 4.

C Ifdoor height is8'-0", you need a RailExtension Kit.(Figure 3).
(SeeAccessoriesOrder Form,Page 16).
D Ifthe door height istaller than 8'-0",

the opener you purchased isthe Rail Extension for
wrong version. Contact 8' door

Customer Service
Representative

at 1-800-354-3643.

Figure 3 Rail Extension Kit

NOTE

The header is a heavily reinforced section of the wall just
above the top of the garage door opening.

A Findvertical center line of door and header:

• Closedoor.

• Measuredoor width at top.

• Marka point at center of door and on headerdirectly

above door. Draw a center lineto connect points.

B Find Header Bracketmounting height (Figure 4): (Do not attach
Header Bracket).

• Raisedoor, watching top edge of door and stop door
when its edge reachesits highest point.

• Measuredistance ("H") from top edge of door to floor.

- Forsectional doors,add 2-1/2" to "H". Mark a point

on center line. Bottom of Header Bracketwill be

installed here.

- Forone-piece doors, add 6" to "H". Markthis point on

center line. Bottom of Header Bracketwill be

installed here.

SECTIONAL DOOR

H÷2_J=2_......

ONE-PIECE DOOR

WARNING:

Ifyour door sticks, binds, or is out of balance, have it adjusted
bya Genie Factory Authorized Dealer. Door springs,cables,
pulleys,brackets and associatedhardware are under extreme

tension and cancause seriousinjury or death.

4

H

Figure 4 Find Highest Point of Travel

ForHelp,call 1-800-3S-GENIEorvisit www.geniecompany.com

NOTE

• For all types and styles of doors:

- If the ceiling in your garage isso low that there is
not at least a 3" space above the Header Bracket
mountingpoint, contact a Genie Factory

AuthorizedDealer.

• Ifa door spring is in the way, place the Header Bracket
above the spring. Do Not move the door spring.

WARNING:

Door springs are under extremely high tension and

shou d be handed ONLYby atrained professiona.

Perforated Straps

FINISHEDCEILINGS
Locateceilingjoistsortrussesusing

astudfinderorsimilardevice.

Attach angle iron(not included)
to joists or trusses through finish

material using LagScrews.

Figure 6B Mounting methods for open beam or finished ceilings

C Checkwall for a stud or a solid header at your mark: (If checking a
finished wall, a stud finder may be helpful).

• If location isabove Header,a 2"x 6" board must be

screwed to studs besideyour mark with at leasttwo Lag
Screwsand Flat Washers(not provided).

• Transferyour markto new mounting board.

Check ceiling or space above where Opener Power Head will be
mounted (Figure 5): There must be a 120Volt grounded outlet or
wiring box within 3 feet of Power Head.

Grounded
outlet

1

(8' door)

Door Center Line

Figure S Check Power Head location

A The measurements above aretaken from the garage door
centerline toward the rear of the garage.

B Find location of ceiling joist or truss above where Opener Power
Head will beand estimate type and quantity of materials needed for
your installation (Figure 6A & B).

MOUNTING EXAMPLES

Standard Straps

Extra wood required Perforated Angle

Iron

POWERSOURCE

A Checkthat there is a 15Amp 120 Volt grounded electrical
outlet or grounded permanent wiring box (per building code)

within 3' of Opener Power Head(Figure S).

• If not, an outlet or wiring box must be installed. Contact
a licensed electrician for installation.

Ifbuilding codes require permanent wiring, Power Head
must be partially disassembledto install appropriate

wiring in place of Power Cord. (SeeAssemblyand

Installation Poster.)

NOTE

Permanent wiring must be installed by a Licensed
Electrician. Not all Genie Factory Authorized Dealers are

Licensed Electrician's. Contact someone who isa Licensed
Electrician.

WARNING:

Do not use and extension cordi Extension cords Can cause

dangerous overheating COnditions:

Do NOt Use p0rtable generat0rs: This pr0duct isdesigned
to operate on standard house current;

DoNot use alternate power supplies.

MOU_ lJ.......... n ......., ......NNTINGBRACKET LOCATIO

Check for wood garage frame, jamb, or masonry at mounting
location (6" above floor) with attachment tabs facing away

from garage door (Figure 7).

A If you cannot mount Safe-T-Beam ®Mounting Bracket to
wood frame:

. Concrete screws and concrete anchors (not included)

must be used to mount Brackets on masonry with
attachment tabs facing away from garage door.

Safe-T-Beam®Mounting BracketExtensions may be used

(not included - available at Dealeror useorder form pg. 14.

Figure 6A

OPENCEILINGSStrapsand angle iron may attach directly to joists
or trusses.

For Help, call 1=800=35=GENIEor visit www.geniecompany.com

I

Safe-T-Beam ®

Mounting Bracket@/_ / 6"

Figure 7 Mounting I floor

Safe-T-Bea _ ......

Components

_i_ / ...........: Topof

Bracket

_i _rr above

5

A Tools(FigureS):

B Additional tools to make installation easier:

• Slotted and phillips screw-driver bits

• Stud finder

• Sheet-metal cutting snips

Check that the garage door locks, rope, and T-Handles are
removed from the garage door before starting the installation.

A If your garage does not have a separate entry door, it is
highly recommended to install a Genie Emergency Release Kit

(GER-2). Emergency Release Kit lets you open the garage door

from outside if there is a power failure. (Please see Accessories

Order Form on page 14.)

Before going further, get any items and tools if needed

for your installation

Garagedoor frame reinforcement brackets, screws, bracing
or reinforcement kits (dealer)

LagScrews(1-1/4") for a wood door lessthan 2" thick (store)
Electricaloutlet and/or wiring (supplied by a licensed electrician)
Sufficient angle iron or strapping for hanging Power Head(store)
60 Watt light bulbs (Rough service bulbs recommended)(store)
GER-2EmergencyReleaseKit for entry during power failure (store)
Wood for header, ceiling, and/or door braces(store)

Masonry fastenersfor Safe-T-Beam Bracket installation (store)
Safe-T-Beam®Bracket Extensions(dealer)
Masonry drill bit (store)
Extension Kit (for 8' Garage Doors)(dealer)

®

Go to Assembly and Installation Poster for full
Installation Instructions.

IMPORTANT

SAFETY INSTRUCTIONS

!LWARNING:

TO REDUCE THE RISK OF

SEVERE iNJURY OR DEATH

1 READANDFOLLOWALLINSTRUCTIONS.
2 Neverlet childrenoperateor playwith the DoorControls.Keep

theRemoteControlawayfrom Children.

3 Alwayskeepthe movingdoor insightand awayfrom peopleand

objectsuntil the door iscompletelyclosed.
NOONESHOULDCROSSTHEPATHOFA MOVINGDOOR.

4 NEVERGOUNDERA STOPPED,PARTIALLYOPENDOOR.
5 TestOpenermonthly. The,door MUSTreverseon contactwith

a 1-1/2 highobject (ora 2 x4 boardlaidflat)atthe centerofthe
doorwayonthe floor. Afteradjustingeitherthe Forceorthe Limit
oftravel,retestthe DoorOpener Failureto adjustthe Opener
properlymaycausesevereinjuryordeath.

6 Whenpossibleusethe EmergencyReleaseony whenthedoor

isclosed. Usecautionwhen usingthis Releasewith dooropen.
Weakor brokenspringsarecapableof increasingthe rateof door
closureand increasingthe riskof severeinjuryordeath,

7 KEEPGARAGEDOORSPROPERLYBALANCED.SeeOwner's

Manual.An improperlybalanceddoor increasesthe riskof severe
injuryordeath. HaveaGenieFactoryAuthorizedDealermake

repairsto cables,springassemblies,andother hardware,

8 SAVETHESEINSTRUCTIONS.

NOTES, REMINDERS

Adjustable Wrench

6

1t16" 5/32" Tape Measure'_

Drill Bit Drill Bit

Wire

Stripper

Hammer

Hack Saw

Figure 8 Recommended Tools

Safety Glasses

Wrench

Carpenter's Level

Phillips Screwdriver

Flat Blade Screwdriver

CF i_ ::: :: ....................

Pencil

1/4" 5/I6" 3/8" 7/16" 1/2" 9/16"

Sockets

AWARNING

use the Wall Console induded_ith opener:Any, other wall
console can causethe Opener to operate unexPectedly and the
light to stop working. 1

For Help, call 1-800-35-GENIE or visit www.geniecompany.com

_DJUSTMENTS

SET LIMIT SWITCHES AND

FORCECONTROLS

Coarse Setting of Limit Switches

A Setting Close Limit Switch

. Check that Carriage Assembly is disengaged.
. With garage door fully closed, slide Close Limit Switch

until it is aligned with the center of the
Carriage Assembly.

. Tighten Set Screw. Do Not over-tighten.

B Setting Open Limit Switch

. Manually open garage door to full open position.
. Slide Open Limit Switch until it is aligned with the center

of the Carriage Assembly.

. Tighten Set Screw. Do not over-tighten.
. Re-engage Carriage Assembly.

Setting Force Controls and Final Adjustment of
Limit Switches

i, Thegarage door opens rapidlyi and Cancause serious

: injury or deathl
; Keep the path Clear:

' Position the ladde[ to the Side of the Power Head Soit iS

Clearofall moving parts ofthe Opener and the door,
Set the dooi Opener to use the minimum force needed

to open the door.

CLOSEADJUSTMENT

A

o

On front panel of Power Head find adjusting screw

marked "CLOSE" (Figure 9).

• Gently turn screw counterclockwise until it stops.

- Very little force is required to turn adjusting screw.

• Press Wall Console to close garage door.

- Observe if door stops at "CLOSE" limit switch.
If door is fully closed--adjustment isfinished.
Go to "OPEN" Adjustment.

- If door stops but is not fully closed,
a. Measure distance between bottom of door

and floor.

b. Move "CLOSE" Limit Switch that same distance

toward door.

- If door stops and/or reverses before reaching the
"CLOSE" Limit Switch

a. Slightly increase CLOSEForce setting (clockwise).

- If door reverses after contacting floor, move Limit
Switch toward Power Head.

- If door fails to move, check Safe-T-Beam ®System. See

Troubleshooting Section, pages 10 and 11.

NOTE

• Little effort isrequiredto turn the ForceAdjusting Knobs.

• Ifthe door stops moving while opening or closing,adjust the
Open Forceor CloseForceControlsslightly clockwise(to
slightlyincreasethe force) and retry the step.

• TheOpen Forceand CloseForceControlsareto be setto the

minimum force necessaryto ensurethe door smoothly opens
and closescompletely.

• Ensurethe CarriageAssemblyisengaged and isbetween the

two Limit Switches beforeoperating the Opener.

Thegaraged0oi Opensrapidly;andcan causeSeiOus

injury Ordeath:

Keepthepath clear:
Positionthe ladder to the sideOfthe Power Headso it

is € earof al!mo_ing parts of the Opener and the door
i; Set the door opener to usethe minimum force needed

to open the door:

IB OPEN ADJUSTMENT

• On front panel of Power Head find adjusting
screw marked "OPEN" (Figure 9).

• Gently turn screw counterclockwise until it stops.

- Very little force isrequired to turn
adjusting screw.

• Press Wall Console to open garage door.

- Observe if door stops at "OPEN" limit switch.
If door isfully open--adjustment is finished.

- If door stops but isnot fully open,
a. Measure distance between bottom of

door and top of door opening.

b. Move"OPEN" Limit Switch that same

distance toward Power Head.

- If door stops before reaching the "OPEN"
Limit Switch

a. Slightly increase OPEN Force

setting (clockwise).

- If door fails to move, see Troubleshooting
Section, pages 10 & 11.

C Run Door Opener

• Cycle opener a few times to double check

settings. Repeat adjustment steps as necessary.

OPEN

FORCE ...

LOCATED
UNDER

LIGHT

COVER

CLOSE /

FORCE

CLASS 2 SUPPLY
18-30 VOLTS

Figure 9 Making Force Adjustments
(Located Lower Right Corner).

For Help, call 1-800-35=GENIE or visit www.geniecompany.com 7

SETTING CONTACT

REVERSEFUNCTION

NOTE

Limit Switch and ForceAdjustments must be completed before
checkingthe contact reversefunction.

A Open garage door using Wall Console.

B Lay a 2" x 4" board flat in center of doorway (Figure 10).

C Close door using Wall Console.

D Check that door stops and reverses within 2 seconds after it

contacts board:

• If door does not reverse, decrease Close Force until
door reverses (Figure 9).

• If door still does not reverse, move Limit Switch
toward door.

E Check Safe-T-Beam ®System operation:

• If beam isblocked, door
will not close.

Figure 10 F
Checking _J

Contact
Reverse

/J_-_ laid flat

2" x 4" board

NOTE

The door must contact the 2" x 4" board before the

Carriage activates the Close Limit Switch. If not,
readjust the Close Limit Switch.

ACCESSORIES

PROGRAMMING THE

REMOTE CONTROL

A To program one Button of a Remote Control (Figure 11):

• Locate Learn Button and Learn Indicator Light near

Terminal Block on Power Head (Figure 12).

• Press and release Learn Button. Red Learn Indicator Light
will blink 2 times per second.

• Press Remote Control Button once within 30 seconds. Red
Learn Indicator Light will stay lit.

• Press Remote Control Button again. Red Learn Indicator
Light will go out, indicating that memory is stored.

• Press again to Activate Unit.

B Program each additional Remote using step A above.

To Erase All Remotes from Power Head Memory

A Press and hold Learn Button on Power Head for 10 seconds

or until Learn Indicator Light goes out. Memory is erased:

• Program Remotes again as needed.

To Replace Remote Control Battery

A FOR NON-FLASHLIGHTMODELS

• Pop off the back of the transmitter.

- Use coin, pen, screwdriver or any similar device.

- Replace old Battery with new coin type battery.

o Replace back of remote.

B FOR FLASHLIGHT MODELS

• Slide open battery cover.

- Replace old Battery with new AAA battery.

o Replace battery cover.

A WARNING

Amoving garagedoor maycauseserious njuryor death.

--_ Keeppeopleclearof openingwhile door ismoving.
Donot allowchildrento playwith the RemoteControls,

Ifthe SafetyReversedoesnot work properly:

" Closethedoor anddisconnecttheOpenerusingthe

EmergencyReleaseCord.

, Donot usethedoor Opener,RemoteControls,or

WirelessKeypad.

• Referto the door anddoor 0 penerOwner'sManuals
beforeattempting anyrepairs.

Remote Control Operation

A

PressButton on Remote Control. Garage door will move.

B

Press Button again. Garage door will stop:

• The door automatically stops at the end of the

open or close cycle.

Press Button again. Garage door will reverse.

Figure 11

1-Button and 3-Button
Compact Remotes
w/Docking Station

D There are several additional varieties of remote controls
available from your local dealer, some equipped with

a flashlight.

_b

©

....@(h

CLOSE@ MOREFORCE

LOCATED
UNDERTHE
LIGHT COVER

Figure 12 Learn Code Button and Indicator Light.
(Located Lower Right Corner).

©

LEARN

INDICATOR

_-- LIGHT

---- LEARN

CODE

BUTTON

NOTE

e

Each Remote Control must be programmed
separately.

• The Remote Controls will not close the garage with
malfunctioning Safe-T-Beam®System.

• Program Remote Controls, while at least 24" from
Antenna Wire.

• If the red Learn Indicator Light blinks rapidly,
programming stopped. Restart programming.

• Each Button on a multi-button Remote Control is
for a different Opener. Cannot use more than one

Button for same Opener.

• A maximum of seven Remote Controls or Wireless
Keypads can be stored into the Receiver at one

time. If a Remote Control becomes lost, or if you
want to delete a Remote Control or Wireless

Keypad, see "To EraseAll Receiver Memory."

8 For Help, call 1-800-3S-GENIE or visit www.geniecompany.com

iNSTALLATiON OF LENSAND BULB

A Install a light bulb (1O0Watts or less)(not included) into Light

Socket (Figure 14):

• Rough service, 130 Volt bulbs are recommended.

B Install Lens into slots in Motor Cover.

• Insert Bottom hinges into slots provided inmetal front

cover of Power Head.

• Flip Lensup and fasten with molded latches on lens.

Transmitter Compliance Statement

Transmitters comply with all United States and Canadian legal requirements as of the
date of manufacture No warranty is made that they comply with all legal requirements of
any other jurisdiction.If transmitters are to be used in another country, the importer must

determine compliance with any local laws and regulations which may differ from United

States and Canadian requirements prior to use.
Los transmisores cumplen con todas las reglamentaciones [egales de los Estados Unidos y

del Canad&, en [a fecha de fabricaci6n. Ninguna garantfa se da que cumplan con todas as
reglamentaciones legales de ninguna otra jurisdicci6n. Si los transmisores se van a utilizar

en otro pals, el importador debe determinar si cumplen con las reglamentaciones y [eyes

locales que puedan ser diferentes a las reglamentaciones de los Estados Unidos y del
Canad& antes de usar los mismos.

Les emetteurs sont conformes _ la reglementation am_ricaine et canadienne _ compter
de leur date de fabrication. Aucune garantie n'est stipul6e indiquant qu'ils sont conformes

routes [es prescriptions juridiques d'autres autorit_s. Si les _metteurs sont utilis_s dans

d'autres pays, i[ incombe a I'importateur d'en d_terminer leur conformit_ aux lois et

regles locales pouvant diff_rer de celes des Etats-Unis et du Canada avant toute
utilisation desdits _metteur£

Sendeger_ite entsprechen allen gesetzlichen Bestimmungen in den USA und Kanada zum
Zeitpunkt der Herstellung,Wir Obernehmen keine Gew_ihrleistung for die Einhaltung aller

gesetzlichen Bestimmungen in anderen Lindem. Sollen Sendegerite in anderen L_ndem

eingesetzt werden, so muss der Importeur vor dem Gebrauch sicherstellen, dass die
Sendeger_te auch solchen Iokalen Bestimmungen entsprechen, wekhe yon den

Bestimmungen der USA und Kanadas abweichen.

nlF+-t iOl 71El Ef-_--_ xlgqlAt +,"-f&_-I _-,'q:>- _-_°_;q_i,q_SFTlO_l o_,,ti _lq_t _HI-F.F_P--IS_

F&_,_I _l-@_Cl_____ :::z _Cl c" I _'_f __allOtl [qe-l-oi: _;q°l o:i _ z_oHof

NOTES

Figure 14 Install Lens and Light bulb

IMPORTANTSAFETYINSTRUCTIONS

WARNING--

TO REDUCE THE RISK OF

SEVEREINJURY OR DEATH

1 READAND FOLLOWALLINSTRUCTIONS.
2 Never let children operate or play w th the Doo_

Controls. Keepthe Remote Control away from children.

3 Always keep the moving door in sight and away from

people and objects until the door iscompletely closed.
NO ONESHOULD CROSSTHE PATH OFTHE

MOVING DOOR.

4 NEVERGO UNDERA STOPPED,PARTIALLY

OPENDOOR.

5 Test Opener monthly,. The door MUST reverse on

contact with a 1-1/2 high object (ora 2 x 4 board
laid flat) at the center of the doorway on the floor. After
adjusting either the Forceor the Limit of travel, retest
the Door Opener. Failureto adjust the Opener properly
may causesevere injury or death,

8 When possibleusetheEmergencyReleaseonlywhen

the door isc osed. Usecaution when using this Reease

with thedooropen. Weakorbrokenspringsarecapable
ofincreasingthe rateof doorclosureandincreasingthe
riskofsevereinjuryordeath.

7 KEEPGARAGEDOORS PROPERLYBALANCED. See

Owner's Manual. An improperly balanced door increases
the risk of severe injuryor death. Havea Genie Factory
Authorized Dealermake repairs to cables,spring

assemblies,and other hardware.

8 SAVETHESEINSTRUCTIONS.

For Help, call 1-800-3S-GENIE or visit www.genie¢ompany.com

SCHEDULED MAINTENANCE

A

Monthly:

o

Door springs and door hardware:

- Oil door roller, bearings, and hinges using silicone
lubricant or light oil.

Reattach Carriage Assembly to Rail Assembly:
a. Pull the Emergency Release Knobtoward

Power Head.

b. Close door.

Contact Reverse Test,

- Perform Adjustment Step 2 on page 8.

A WARNIN J

--Do not operate door auto atiCally 0r man_al/y if Springs
are broken, Contact aGenie Fact0ry Authorized Dealerfor

service or call Customer Service at 1,800,35'GENIE. !

• Balance Door.

- Close door.

- ReleaseCarriage Assembly from Rail Assembly by pulling
down on Emergency ReleaseKnob.

- Raisedoor manually 3'- 4' and verify that door stays at
that position. See Check Step 2 on page 4.

NOTE

When the door is3'- 4' above the ground, the door
should stay open. Slight movement isacceptable. If

the door moves too much, contact a Genie Factory
Authorized Dealer for service or call Customer Service at

1=800=35=GENIE.

AWARNING

Ifthe door fails to reverse on contact with the board,

adjust the Close Force Control as specified in Set Limit
Switches and Force Controls on page 9. If the Opener still
fails, contact a Genie Factory Authorized Dealer for service

or call Customer Service at 1-800-35-GENIE.

FCCAND IC CERTIFIED

All devices comply with Part 15 of the FCCRules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference,and (2)
this device must accept any interference received, includ-
ing interference that may cause undesired operation.

B As Needed:

• Replace Light Bulb

TROUBLESHOOTING GUIDE

Safe=T=Beam ® System Self=Diagnostic Troubleshooting

Source (Red LED)

ON
OFF

OFF

2 BLINKS, Pause
(Repeat)

2 BLINKS, Pause
(Repeat)

3 BLINKS, Pause
(Repeat)

4 BLINKS, Pause
(Repeat)

Sensor (Green LED)

ON

OFF

ON

ON

OFF

ON

ON

Normal operation
o Power Head not powered

oWiring from Power Head bad

o Wiring to Source missing or bad
o Power has been interrupted

o Beam not aligned
o Beam obstructed

o Sensor defective

o Wire to Sensor missing or bad
o Sensor defective

o Sensor receiving interference

. Source not sending pulses
. Source defective

Possible Problem

Solution

None required

. Check breakers, fuses, plugs
. Check wiring for obvious shorts

. Check wiring
. Remove power and reapply

. Check Source, Sensor alignment
. Check for obstruction

. Contact Customer Service

o Check wiring
o Contact Customer Service

o Determine source of interference
o Check for sunlight or another

opener on nearby door

. Contact Customer Service
o Contact Customer Service

. Contact Customer Service

10 For Help, call 1=800-35-GENIE or visit www.geniecompany.com

Problem

Openerdoesnot run
from WallControl

Door Opener starts
for no apparent reason

Door starts down, then
stops before it is
completely closed

Door starts down, then
stops and goes back up

Door will only run closed

Doorwill onlyrunopen

Lightswill not turn off

Doorstartsup,
but stopsbeforeit is
completelyopen

Operator runs,but door
doesnot move

WallConsoleVacation
Lockfunction does
not work

Noisy Operation

General Troubleshooting

What To Do

1. Check Lock switch on Wall Control Installation Poster.

2. Check Power Source:

• For Grounded Plug Connection.

- Plug a lamp into the electrical outlet used for the door opener.
a. If lamp lights, power source is good.
b. If lamp does not light, check fuse or circuit breaker.

• For Permanent Wiring Connection.

- Check fuse or circuit breaker.

3. Check connections (seeWall Console Installation on Installation Poster):

• At Power Head Terminals and Wall Control.

1. Check Wires to ensure that they are not cut (Staples can cut insulation and short Wires)
Replace any shorting Staples and shorted Wires.

2. Was Remote Control lost or stolen? If so, erase all Remote Control codes from Receiver's memory
and reprogram for remaining remote controls. (See EraseAll Receiver Memory on page 8).

3. Ensure that no Buttons are stuck "pushed-in" on Wall Console or any Remote Controls.

1. Check Close Limit Switch setting (page 7and poster). Adjust as needed.

2. Check Force Setting (pages 7).Adjust asneeded.

3. Check for shorted wires.

1. Ifa new installation, check Door Arm position.

2. Check operation of Contact Reversefunction.

3. Check Safe-T-Beam®Systemfor beam obstruction or misalignment of Lenses.

4. Check Safe-T-Beam®System diagnostic code.

5. Check CloseForceadjustment (seeSet Limit Switchesand ForceControlson pages7). Adjust as needed.

6. Check garage door for binding.

1. CheckOpen Limit Switch for ashort circuit and for proper wiring.

2. Check Open Force adjustment (seeSetLimit Switches and ForceControls on pages 7). Adjust asneeded.

3. Check condition of garage door and door spring(s).

4. WARNING: If you suspecta problem with the garage door hardware or springs,contact a Genie

FactoryAuthorized Dealer for service,or contact Customer Serviceat 1-800-35-GENIE.

5. CheckPosition of Lock Switchon Console.

1. CheckSafe-T-Beam®Systemasdetailed in the Safe-T-Beam®System Self-diagnosticTroubleshooting Chart
(page 10).

2. CheckCloseLimit Switch for a short circuitand for proper wiring.

3. CheckCloseForceadjustment (seeSet Limit Switchesand Force Controlson pages7). Adjust asneeded.

1. Disconnect Wires connectingPushbutton to Power Head(seePushbutton Installation on poster).
Checktheir conditionand either replaceor reconnect.

2. Until a replacement WallConsolecanbe obtained, disconnectWall Consoleand useonly Remote Controls
or WirelessKeypadto operate Opener.

3. Check for non-compatible wall control.

1. Check(ensure) that garage door and Opener are in good repair, properly lubricated, and properly
balanced as detailed in Maintenance Section.

2. WARNING: If you suspecta problem with the garage door hardware or springs,contact a Genie Factory

Authorized Dealerfor service,orcontact Customer Serviceat 1-800-3S-GENIE.

3. CheckOpen Limit Switch for a short circuitand for proper wiring.

4. CheckOpen Forceadjustment (seeSetLimit Switchesand ForceControlson pages7). Adjust as needed.

1. EnsureCarriageAssembly isengaged to CarriageSlide(seeInstallCarriageAssemblyontoRailsonInstallationPoster).

2. CheckForceadjustment (seeSet Limit Switchesand Force Controlson pages9and 10). Adjust asneeded.

1. EnsureCarriageAssemblyis in contactwith CloseLimit Switch.

2. Checkwhen door isfully closed,that CarriageactivatesCloseLimit Switch. Ifnot, adjust position of Close
Limit Switch (Seepages7).

1. Besureall fastenersare tight.

2. Check (ensure) that garage door and Opener are in good repair, properly lubricated, and properly
balanced as described in Maintenance Section (page 10).

For Help, call 1-800-35-GENIE or visit www.geniecompany.com 11

PARTS iDENTIFICATION

Power Parts _.auded

[1]Power Head Assembly Item Part Name

.1 Power Head Assembly 1

* 1A Cover (by Series Model) 1
* 1B Front Panel Assembly 1

* 1D Motor Parts 1
* 1E Circuit Board Assembhz 1

* 1F Capacitor (By Series/Model) 1

1G Opto Wheel (not shown) 1

* 1H Carriage Slide 1
* 1J Chain 1

1K Circuit Board Bracket 1
* 1L Drive Module 1
* 1M Terminal Strip 1

* 1N No. 8-32 x 3/4" Hex Head Screw

1P Shock Absorption Stop 1
* 1Q Motor Mount Bracket (not shown', 1

1X Chassis 1

4 1/4-20 Shoulder Bolt 1

5 1/4" Flange Nut 1

39 Coupler 1

41 No. 8-32 x 3/8" Phillips

42 No. 8-32 x 3/8" Phillips

48 Mountinq Straps 2
49 Light Lens 1

* Pre-assembled

Head List Number

w/int. Lockwasher 1

Hex Head Screw 1

Pan Head Screw 1

WIRING DIAGFIAM [ A Shut 0ff Cower bef0re 0penilg the cdver:[Components inside Cover May Cause Electric Shock J

, M°L°R.

I I

, _,_

I THERMAL _ _i:Y I [
] PROTECTOR [ "_ ,,,,,(::_ i [

BLACK ' _ _'_/ I _ MOTOR

RED

2

ORANGE

J

YELLOW YELLOW

i I

;RED YELLOW',

i j

POWER CORD

z

POWERHEAD TERMINALS

WALLCONTROL

/_7 _

®®®o6®®®@®®®

SEQUENCER HOUSING

WHITE BLUE

LIGHT

OPENLIMIT

COMMON

CLOSELIMIT

IIM] SWITCH

OPIN

(JO'l

[_. LMIT SWTCH

12 For Help, call 1-800-35-GENIE or visit www.geniecompany.com

PARTS iDENTIFICATION

[2]RailAssembly

\

Parts List

item Part Name

1 PowerHead Assembly (main box)
2 RailAssembly (1-piece)

4 RailAssembly_3:piece)(main box)

5 First RailSection (separate box)

6 Middle RailSection (separate box)

7 End Railsection (separate box)

8 RailClamps (blue bag)

9 1/4"-20x 5/8" HexHead Bolt (blue bag)
10 1/4"-20" Hex Flange Nut (blue bag)
11 Carriage Assembly (main bag)

12 RailStrap (blue bag)
13 Limit Switch (white wire)(blue bag)

14 Limit Switch (brown wire)(blue bag)
15 ReleaseCord(green bag)

16 ReleaseKnob (green bag)
17 Emergency ReleaseTag (green bag)

18 HeaderBracket orange bag)
20 Door Bracket (orange bag)

22 1/4" x2" LagScrew(orange bag)
23 Straight Door Arm (mainbox)
24 ClevisPin (yellow bag)

25 Cotter Pin (yellow bag)
26 Curved Door Arm (main box)

27 3/8"-16 x 7/8" H.H.Bolt (yellow bag)
28 3/8"-16 Hex Nan e Nut ( ellow ba )

29 Wire (main box)
30 Insulated Staples(red bag)

m

1

I
I
I

I

4

12
12

I
I

I
I

I
I
I
I
I

8

I
2
2

I
2

2

I

variesby

model

Parts List

item Part Name

31 Wall Button (red bag)
32 Wall Console (main box)

33 #6x 1-1/4" pan head phillips screw

34 Entrapment Warning Label (manual)
35 Safe-T-Beam®Sensor (main box)

36 Safe-T-Beam®Source (main box)
37 Safe-T-BeaM®Mountinq Brackets
38 Remote Controls (main box)

39 #8-32x 1"Machine Screw (green bag)

40 Safetyand Maintenance Guide (manual)
41 Wire Clips

42 1/4"-20 x 3/4" Self-drilling Screws

(orange bag)

44 #10-16x 1-1/4" Phillips Hex Head Screw

(yellow bag)

46 5/16"-18 x 3/4"Hex Head Bolt

(orange bag)
47 5/16"-18 Hex Flange Nut (orange bag)
48 Mounting Straps (main box)

m

variesby

model

varies by

model

variesby

model

1
1
1
2

variesby

model

2

1

variesby

model

3

4

3
4
2

For Help, call 1-800-3S-GENIE or visit www.geniecompany.com 13

GarageDoorOpenerAccessoriesOrder Form

Formulairedecommandodesaccessoirespourouvre-porte de garage

For additional accessories not shown, visit our website at www.geniecompany.com
pour lesaccessoires suppl4mentaires pas montr4, visiter notr_ site web _ www.geniecompany.com

How many?

Comment
beaucoup?

(GKT-1-390) 1-ButtonCompactRemote-Allowsremoteoperationofgaragedoor.

1-BoutennerT_l_cornrnaadecornpacte- Permettreoperation_loign"deportedegarage.

P/N 36248R 536.50

(GiFT-I-390) 1-ButtonFlashlightTransmitter-RemoteControllerwithaFlashlight.

1-houtenner['_rnetteurde[arnpedepoche- Lecontr61eur_loign_avecdelampedepoche.

P/N 35657R 545.00

{GICT-3-390)3-Bu_enCornpactBernete-AIIowsremoteoperationof3garagedoors.

3=boutennerlaT_l_cornrnandecornpacte- Permettreoperation_loign'

troisportes de ara e. P/N 36223R 550.00

(GWC-2W) Deluxe Wall Console - OperatesGarageDoor.Independentlightcontrol. Securityvacationlock.

LaConsole dseluxe deMur- Actionne la porte degarage.Commanded'_clairageind_pendante.
Interrupteurde verrouillagede s_curit&

P/N 35661R 535.00

(GWKPD)DualFrequencyWirelessKeypad-OperatesIntellicode'GarageDoorOpenerswithoutRemoteControl

orkey.
Syst_rned'ouvre-pertedegarage_ claviersansfil- Actionnelesouvre-portedegarageavec

Intellicode'sanst_l_commandenicl&

(GLU-3)

(Gw-2)

(6PS-5)

(GABXS)

P/N 35691 R

3/4 oz. ScrewDrive Lubricant-Ensuresproperequipmentwearprotection.
Laonza3/4 Lubricantdela vis-Garantircomponantexactparsyst_med_fenseversuser.

P/N 35218AS

UniversalWall Button- Providesadditionalconvenientinsideoperationof door.
Bouten mural universal - ActionneI'ouvre-portede I'int_rieurdu garage.

P/N 35693R 53.75

PerfectStep- Ensuresperfectparking.
Butoir PerfectStop- Permetde stationner_ laperfectiondanslegarage.

P/N 35677R 54.00

BeltDriveExtensionKit-AnExtensionthatincreasesthe travelofabeltdrivenOpenerto

550.00

accommodateaneightfootdoor.
N_cessairede prolongernentducoulisseau-Rallongedeprolongeantlacoursederouvre-porte

BeltDrivepouruneportede2,4m(8pi)dehauteur.

P/N 35663R

(LCGX-8) Chain Drive ExtensionKit- An Extensionthatincreasesthe travelof a ChainDrivenOpenerto

accommodateaneight foot door.
N@cessairede prolongernent ducoulisseau -Rallongedeprolongeantlacoursederouvre-porte

du conduit dechainpourune portede2,4 m (8pi) dehauteur.

P/N 35679R 532.00

(GSX-8) ScrewDriven Extension Kit - AnExtensionto increasetravel of ascrewdriven Operatorto accommodate

an eight foot door.

coursedeI'ouvre-portepourune portede 2,4m (8 pi) de hauteur.(GIRU-lT) _-e_

N_cessairede taffonge du Screw Drive- Rallongedeprolongeant la

P/N 35678R

532.00

532.00

(60WATT)Enhanced/RoughServiceLightBulb-Ensuresproperequipmentcompatability.

(GER-2)

STB

Eclairagede50 WATT-Garantircomponantexactparsyst_me.

Emergency Release Kit - Provides access to garage from outside in the event of
an electrical power failure.

N6cessaires de D4clenchement de secours - Len_cessaire de d_clenchement
de secours est con_upour vous permettre d'acc4der & votre garage depuis

I'ext_rieur en cas de panne de courant et Iorsqu'il.

Adapter Brackets (2) - Used in conjunction with standard STBBrackets. They
provide additional clearance and mounting options.

Crochets d'adaptateur (2) - Utilis_ conjointement avec STBstandard reenter
les crochets, ils fournissent le d_gagement suppl_mentaire avec monter d'options.

P/N 26210A.S

P/N 35675R

P/N 34439R.S 54.37

520.00

55.00

52.73

Ordering Instructions

No C.O.D.shipments. Please include check or money order,
made payable to The Genie Company. Do not send cash.

Allow 3-4 weeks for delivery.
1-800-354-3643. Please have part number and credit

card ready. Mail Order Form to: Genie Company, 22790
Lake Park Blvd, Alliance, Ohio 44601. We accept Visa or

Mastercard on phone orders only.

Please add local sales tax if you reside in one of the states listed.

Californla, Connecticut, Florida, Georgia, Illinois, Indiana,
Maryland, Massachusetts, Michigan, New Jersey, New York,
Ohio, Tennessee, Virginia, Wisconsin

TOTAL ORDER $

SHIPPING & HANDLING $ 6.00

STATE SALESTAX $

GRAND TOTAL $

Instructions Commandant

Pasd'exp_ditioncentre remboursement.Veuillezinclure un cheque
ou un mandat bancaire,le payablefaitaThe Genie Company.

N'envoyez pasd'argent comptant. Accordezde 3 _4 semaines
pourla livraison.1-800-354-3643.Ayezsousla mainle num6rode la

pieceet celui de lacartede credit.Mettre _la paste learrngement
_:GenieCompany,22790 LakePark Bivd, Alliance,Ohio 44601.

Nousacceptonslescommandespar t_l@hone avec paiementpar
cartede creditVisaou Mastercard.

Veuillez indiquer les taxes de vente locales si vous r4sidez dans I'un des

_tats r4pertori4s ¢i-dessous.

California, Connecticut, Florida, Georgia, Illinois, Indiana,
Maryland, Massachusetts, Michigan, New Jersey, New York,

Ohio, Tennessee, Virginia, Wisconsin

COMMANDETOTALE $

MANUTENTIONETEXPEDITION $ 6.00

TAXEDEVENTE $
TOTALGLOBAL $

SHIP ORDER TO:
EXPEDIER MARCHANDISE POUR:

NAME / NOV

ADDRESS / ADRESSE

CITY / VILLE

STATE / ETAT

ZIP / CODE POSTAL

(Pricessubject to change without notice)
(Lesprix assujettissentpourchanger sansla notification)

14 For Help, call 1=800=35=GENIEorvisit www.geniecompany.com