Genie 2024, 2022, 2042 User Manual 2

A L WAY S A T Y O U R C O M M A N D

Installer:

Leave this manual
with homeowner.

Homelink® is a registered trademark of
Johnson Controls Technology Company.

®

is a registered trademark of

Car2U
Lear Corporation.

© The Genie Company 2012.

PN 37026501206, 1/27/2012

Models 2022/2024/2042

GARAGE DOOR OPENERS

Includes: 2-Bulb Light System
Wall Console

Includes INTELLICODE® Remote Control
Safe-T-Beam

®

System must be installed to close door.

For use only with sectional doors.

Homelink® and Car2U® compatible

For Answers and Assistance:

1.800.354.3643

or visit www.geniecompany.com

SAVE THIS MANUAL FOR FUTURE REFERENCE

SAFETY INFORMATION

OVERVIEW OF POTENTIAL HAZARDS

READ THIS SAFETY INFORMATION

Garage doors are large, heavy objects that move with the help of springs under high tension and electric motors. Since moving
objects, springs under tension, and electric motors can cause injuries, your safety and the safety of others depend on the owner or
user of this system to read, understand and implement the information in this manual. If you have questions or do NOT
understand the information presented, contact The Genie Company or an authorized Genie

The safety alert symbol and following signal words DANGER, WARNING, and CAUTION are used throughout this manual to call
attention to and identify different levels of hazard and special instructions.

This is the safety alert symbol. This symbol is placed next to signal words and messages to help you identify

important safety information

The word:

DANGER indicates an imminently hazardous situation which, if NOT avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation which, if NOT avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation which, if NOT avoided, may result in injury or property damage.

The word NOTE is used to indicate important steps to be followed, important considerations, or location of parts.

®

Dealer.

POTENTIAL

HAZARD

MOVING DOOR

ELECTRICAL

SHOCK

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

EFFECT PREVENTION

WARNING:

Could result in Death

or Serious Injury

WARNING:

Could result in Death

or Serious Injury

Keep people clear of opening while door is moving.

Do NOT allow children to play with the door operator.
Do NOT operate a door that jams or one that has a broken spring.

Turn OFF power before removing operator cover.
When replacing cover, make sure wires are not pinched or near

moving parts.
Operator must be properly grounded.

2

HIGH

SPRING

TENSION

WARNING:

Could result in Death

or Serious Injury

Do NOT try to remove, install, repair or adjust springs or anything to
which door spring parts are fastened, such as, wood blocks, steel
brackets, cables or other like items.

Installations, repairs and adjustments must be done by a trained door
system technician using proper tools and instructions.

PN 37026501206 01/27/2012

TABLE OF CONTENTS

OPENER FEATURES

SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PAGE

SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

OPENER FEATURES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

SAFETY FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

PRE-INSTALLATION CHECK LIST . . . . . . . . . . . . . . . . . . . . . . . 4-5

RECOMMENDED TOOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

PARTS IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7

KEY ILLUSTRATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

SAFETY INSTALLATION INFORMATION . . . . . . . . . . . . . . . . . . . . 9

INSTALLATION

1 OPENER ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11

2 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-14

3 WALL BUTTON INSTALLATION . . . . . . . . . . . . . . . . . . . 15-16

4 SAFE-T-BEAM®SYSTEM INSTALLATION . . . . . . . . . . . 17-18

5 CONNECTING TO POWER . . . . . . . . . . . . . . . . . . . . . . . . . 19

ADJUSTMENTS

6 LIMIT SWITCHES & FORCE ADJUSTMENT . . . . . . . . . 20-22

KEYED EMERGENCY RELEASE . . . . . . . . . . . . . . . . . . . . 21

CONTACT REVERSE TEST . . . . . . . . . . . . . . . . . . . . . . . . . 22

7 PROGRAMMING REMOTE CONTROLS. . . . . . . . . . . . . . . 23

INTELLICODE®Rolling Code Security System.

An electronic rolling code system that enhances the security of
the door opener by continuously changing the access code
each time the remote control is used. The door opener
responds to each new code only once. An access code copied
from a working system and tried again will not control the door
opener.

Lighted Wall Console*

Operates door opener from inside garage.

(Refer to section 3)

Follow the Homelink
owner’s manual.

SAFETY FEATURES

Safe-T-Beam®Non-Contact Reversing System**.

Puts an invisible beam across the door opening. The door stops
and reverses to the full open position if anything passes
through the beam. Red or green LED indicator lights on the
power head provide a self diagnostic code if an operational

8 BATTERY/ VISOR CLIP INSTALLATION . . . . . . . . . . . . . . . 24

9 LIGHT BULB AND LENS INSTALLATION . . . . . . . . . . . . . . 24

SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

MAINTENANCE & TROUBLESHOOTING

10 ROUTINE MONTHLY MAINTENANCE . . . . . . . . . . . . . . . . 25

WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

TROUBLESHOOTING GUIDE - OPENER. . . . . . . . . . . . . . 27

TROUBLESHOOTING GUIDE - POWER HEAD LED . . . . . 28

TRANSMITTER COMPLIANCE STATEMENT . . . . . . . . . . . . . . . 29

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

problem exists. (Refer to Section 10.)

Safe-T-Reverse

Automatically stops and reverses a closing door within 2
seconds of contact with an object. (Refer to Section 6.)

Safe-T-Stop

Automatically opens a closing door if it fails to close completely
within 30 seconds.

Watch Dog

™

Monitors the Safe-T-Beam® system to ensure proper function­ality and will automatically stop and reverse a closing door if a
problem is detected.

and Car2U®compatible.

®

or Car2U®instructions in your car

®

Contact Reversing System.

®

Timed Reversed System.

Monitoring System.

*Opener MUST be installed with the

included Wall Console.

**Safe-T-Beam®Safety Reverse System

MUST be installed to close door.

PN 37026501206 01/27/2012

Automatic Lighting System.

One bulb lighting supplies up to 75 watts of light for safer
evening exits and entries. Turns ON when door is activated and
automatically turns OFF 3 minutes later.

Manual Emergency Release.

Manually releases door from door opener. Use during a power
failure or other emergency to allow manual opening and closing
of door. (Refer to Section 6.)

3

PRE-INSTALLATION CHECK LIST

FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

Things to consider if you are planning to "Do-it-yourself."

This opener is designed for use with SECTIONAL doors only.

In many cases you will be replacing an existing door opener with a new one, however, if this

will be the first opener installed there are some pre-installation issues which need to be

addressed. They are as follows:

The Genie Company recommends that you read and fully understand all information and

instructions contained herein before choosing a "Do-it-yourself" installation. Any

questions should be directed to The Genie Company or an authorized Genie®Dealer.

(

The issue numbers below refer to the circled numbers in the illustrations on page 5.

Check your ceiling where the power
head of your new unit will be mounted.

1

Plan how you will be mounting the power head.

It is possible that ceiling joists may not be in the

position needed with respect to the garage door

opener. It may be necessary to add an

additional bracket and

with your new door opener kit).

(Refer to Section 2.)

Check the wall directly above the garage
door

2

must be securely fastened to this wall. Insure

that the structure will provide a strong mounting

location. (

3

obstruction and has a wood surface available

for attaching the mounting brackets

brackets may be attached to concrete if necessary

but extra tools and special fasteners (not supplied)

will be required.

. The door opener’s header bracket

Refer to Section 2.)

Check to see if the mounting location
for the Safe-T-Beam

(Refer to Section 4 and 5.)

fasteners (not included

®

System is clear from

. The

You need a properly grounded 110-120 Volt

power supply available

5

no more than 3 feet from the power head once it is
mounted.

DO NOT USE AN EXTENSION CORD!
DO NOT USE A PORTABLE GENERATOR! This
product is designed to operate on
standard house current.
DO NOT USE ALTERNATE POWER SUPPLIES.

6

remove any door locks, ropes, and/or cables
(NOT door lift cables) prior to installing your
opener

7

(Refer to Section 5.)

WARNING

To avoid damage to your door and/or

opener, make sure you disable and/or

. (

Refer to Section 1.)

Insure that your door is properly balanced
and moving freely. (

. The outlet should be

Remove

Refer to Section 10.)

)

Remove

NOTE: Mounting brackets must be installed

within code specifications.

Is your sectional garage door made of

4

or glass panels

must be added to these type doors. If this is the

case, please contact the door manufacturer or

authorized dealer so that

with a "bracing kit."

aluminum, light-weight steel, fiberglass

? Additional support bracing

they can furnish you

(Refer to Section 2.)

WARNING

To reduce the risk of injury to persons or
damage to property - Use this opener only
with sectional doors.

4

If your door jams, binds, is improperly
balanced or has a broken spring, have it
repaired or adjusted by a trained door system
technician. Door springs, cables, pulleys,
brackets and associated hardware are under
extreme tension and can cause serious injury
or death.

(NOT SHOWN) If your garage does not have
a separate entry door, you should consider

8

an emergency release kit (GER-2)for installation on
your garage door.

PN 37026501206 01/27/2012

WARNING

TYPICAL SECTIONAL DOOR INSTALLATION

FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

Pg. 19

5

TYPICAL SUPPORT

BRACKET

(NOT PROVIDED)

POWER CORD

(APPROX. 45 IN.)

TO 120V GROUNDED

OUTLET

EXTENSION SPRING

TORSION SPRING

NOTE: This opener is designed for

use with SECTIONAL doors only.

1

OR

Pg. 13

Pg. 17-18

Pg. 12-13

2

ADDED
HEADER BRACKET
MOUNTING BOARD

BRACES

Pg. 14

4

Pg. 17-18

MAX. 6"
MIN. 5"

3

6

Pg. 11

SAFE-T-BEAM

3

®

7

Pg. 12

SECTIONAL DOOR

To reduce the risk of injury to persons or
damage to property - Use this opener only
with sectional doors.

PN 37026501206 01/27/2012

WARNING

5

RECOMMENDED TOOLS

ARRANGING BOX CONTENTS FOR ASSEMBLY

FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

Drill

Step ladder

Safety Glasses

PARTS IDENTIFICATION

Safety Brochures

3/16" Drill Bit

Ratchet

Phillips screwdriver

-

Not Shown Full Size .

Pencil

Tape measure

ORGANISATION DU CONTENU DE LA BOÎTE POUR LE MONTAGE

DISPOSCIÓN DEL CONTEN DO DE LA BOLSA PARA EL MONTA E

R move ens Box and motor power h ad

E l ver a bo e des e tles t a t te mo or ée

Q i e la a a de a l nte y l mo or de a c ja e con ol

Caefu ly em ve thrd ra l wi h hain or be t

Ene er o gne semet e t o s ème r i ( vec a

ch î e ou co r oe at a hé ) et e pa er ur e sol

Cudados men e qui e el t rcer el ( on a

c dena o or ea acop ada) y ponga en el

Arange hree sma l box s for e sy acc ss

Ar nge l s t o s pe i es o te de man è e à

pou o r y a cé er ac ement

Dspo ga as re ca as equ ñas p ra en r

R move ai sec i ns not conne ted

nev r l s s c io s de al non onn c ées

Folow nst uct ons n he nsta la ion Manual for a sembly teps

Proc der se on l s intru t ons s ipu ées da s le m nuel d nst l at on pour es ét pes de

Q i e as s c io es de i l no one t das a

rang r es als n l gne t t er ur e man hon en p a tque

p ur e dé age de l chane u r va e en p a t que

oure de ou r ie

Dspo ga os r e e en l n a y es re a c m s de p ás co f era

e la ade a o l zo p á tco de a c r ea

Box Contents Sheet

Remove i te nal box s

nl ve l s bo t s i trn s

Qu e l s c ja i te nas

pso

a ce o f c l

o hain or be t

à la ha ne ou ou r ie

a c dena o or ea

Carpenter’s level

Adjustable wrench

1/4", 7/16", 3/8" and

Wire strippers

Hammer

1/2" Sockets

r

at east 5 e et a bove lo o )

door.

.

© 999

Child can be pinned under automatic garage
Death or serious injury can result.

Never let ch ld walk or run under moving door.

•

Never let ch ld use door opener controls .

•

Always keep mo ving door in sight.

•

If person is p inned, push control button or use

•

emergency re lease.

Test door opener monthly:

•

Re e to you own e s manual
ace

-nch ob ect (o 2x4 laid a ) on oo

doo a ls to eve se on con act ad ust ope ne

I
I opene s ill a ls to eve se do o ep ai o ep ace op ene

Do not emov e o pa nt ove h s la bel

Mount w a l c ont ol out o c hi d s e ach

ace next o wall co nt ol

Entrapment Warning

Label

Safe-T-Beam

®

with wire

(Red LED)

Source

Safe-T-Beam

with wire

(Green LED)

Safe-T-Beam

Source/Sensor Bracket

®

Door Arm

Pro Rail (Chain) Section

Pro Rail (Belt) Section

®

Sensor

Header Bracket

Wire

Wall Control

(varies with model)

Insulated Staple

OR

Door

Bracket

Three-button

Remote Control

Rail Section Clamp

End Rail Section

Center Rail Section

Head Rail (Chain) Section

Head Rail (Belt) Section

6

PN 37026501206 01/27/2012

FASTENERS

BAG NO. DESCRIPTION QUANTITY

0 RAIL SECTION CLAMP 2

RAIL CLAMP BOLT – 5/16 -18 x 5/8'' 8

HEX FLANGE NUT – 5/16 -18 8

1 BOLT – 5/16 -18 x 1/2'' 3

2 CLEVIS PIN, LONG – 5/16" x 3" 1

COTTER PIN 1

HEADER BRACKET 1

LAG SCREW – 5/16'' x 2'' 2

3 HEX BOLT – 5/16 -18 x 3/4'' 5

HEX FLANGE NUT – 5/16 -18 5

LAG SCREW – 5/16'' x 2'' 2

4 SELF DRILLING SCREW – 1/4 -20 x 3/4'' 3

DOOR BRACKET 1

5 HEX BOLT – 5/16 -18 x 3/4'' 3

SELF LOCKING NUT – 5/16 -18 1

HEX FLANGE NUT – 5/16 -18 2

CLEVIS PIN – 5/16" x 3/4" 1

COTTER PIN 1

6 WALL CONTROL ASSEMBLY 1

PAN HEAD PHILLIPS SCREW – #4-24 x 1'' 2

7 13 MM INSULATED STAPLE 30

8 Safe-T-Beam®SOURCE/SENSOR BRACKET 2

PHILLIPS HEX SCREW – #10-16 x 1- 1/4'' 4

WIRE NUT (GREY) 4

NO NUMBER

NO BAG Safe-T-Beam®SOURCE/SENSOR & WIRE SET 1

NO NUMBER

REMOTE WITH BATTERY 1

LIGHT COVER - WHITE 2

Shown Full size (

-

See Parts List below for full description.)

Rail Clamp Bolt - 5/16 -18 x 5/8"

#10-16 x 1-1/4" Phillips Hex Screw

#4-24 x 1" Pan Head

Phillips Screw

Lag screw - 5/16" x 2"

Wire Nut

Self Locking Nut

5/16 -18

Hex Flange Nut

5/16 -18

Hex Flange Nut

1/4 -20

Self-drilling Screw

1/4 -20 x 3/4"

Hex Bolt - 5/16 -18 x 3/4"

MISSING ANY PARTS?

Please call toll free - 1.800.354.3643
DO NOT RETURN TO POINT OF PURCHASE.
IMPORTANT! - Information needed when calling

• Model number - (located on packaging)

• Store, city, state, and date of purchase

PN 37026501206 01/27/2012

Clevis pin

5/16" x 3/4"

Hex Bolt - 5/16 -18 x 1/2"

Clevis pin, long 5/16" x 3"

Cotter pin

Shoulder Bolt

5/16 -18 x 1"

7

1-PIECE RAIL HARDWARE ASSEMBLED VIEW

N

T

Sme do

os ed

b

ra

n Con act

oo dst

buo o

mnu c ue f r

t t s

HGH SPR NG TENS ON

Can C

use

Serio s I

ju

ry o Dea h

ep

r o a j

t

mens mu

t

e

ma

e

y a a

n

d

e

v

e

p

s

n

u

n

o

n

s

c

s

Rail with belt

Belt

Trolley Slide

Belt Clamp

O

ome door

ned

b c

ng

otact

o

r i r

bt r r

manf cur r

or

c

HG

H SPR

NG

T N

SON

Can

Cu

se Se

io

us nu

ry r Death

Re

ars

or

a

us

t e

n

mu

t e

mde y a t

a

ned

v

p

p e o

n

s

t

s

Rail with belt

Center Rail

End Rail

Belt

O

E

Sme do

os e d

rc g Co

ta

t

do ds

iu o o

mau

fa

turr for

HIGH S

PRING TEN

SI

ON

C

n

Caue

Se

ro

us nu

y or Deah

ea s r du

me

s

m

s

be

ae

b

a r in d

r e

o s g o a n

c

n

Rail with chain

FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

Power Cord

Carriage Assembly

CHAIN

Tensioner

Chain

Header
Bracket

3-PIECE RAIL HARDWARE ASSEMBLED VIEW

Clevis Pin, Long
& Cotter Pin

Release
Knob

BELT

Carriage Assembly

Rail with chain

Chain Connector

Power Head

Power Cord

Header
Bracket

8

Tensioner

CHAIN

Clevis Pin, Long
& Cotter Pin

Rail Clamp Bolts

End Rail

Rail Clamps

Chain

Release
Knob

Rail Clamp Nuts

Center Rail

PN 37026501206 01/27/2012

Chain Connector

Power Head

BELT

IMPORTANT INSTALLATION INSTRUCTIONS

Rail Connectors

Rail Connector Bolts

Rail Connector Nuts

WARNING: To reduce the risk of severe injury or death:

1.

READ AND FOLLOW ALL SAFETY, INSTALLATION AND

OPERATION INSTRUCTIONS. (If you have questions or do

not understand an instruction, call the Overhead
Door Corporation.)

2.

Install only on a properly balanced sectional or one piece

garage door. An improperly balanced door could cause

severe injury. Have a trained door system technician make
repairs or adjustments to cables, spring assemblies, and
other hardware before installing the opener.

3.

Remove all ropes and remove or make inoperative all locks

connected to the garage door before installing opener.

4. Where possible, install the door opener 7 feet or more above
the floor. For products having an emergency release, mount

the emergency release within reach, but at least 6 feet above
the floor to avoid contact with vehicles to prevent
accidental release.

5. Do NOT connect the opener to source of power until

instructed to do so.

6. Locate the wall console:

• Within sight of the garage door,

• At minimum height of 5 feet so small children

are not able to reach it, and

• Away from all moving parts of the door.

7. Install the Entrapment WARNING Label next to the

wall console in a prominent location.

8. After installing the opener, the door must reverse

within 2 seconds when it contacts a
1-1/2 inch high object (or a 2 x 4 board laid flat) on
the floor.

PENER ASSEMBLY

1

RAIL ASSEMBLY: Use a clean, flat surface.

NOTE: For 1-piece rail—skip to POWER HEAD &
RAIL ASSEMBLY.

WARNING

To reduce the risk of injury to persons or
damage to property - Use this opener only
with sectional doors.

CAUTION

Do NOT run until opener is fully assembled and

instructed to do so.

NOTE: Three (3) piece rail assemblies are for a 7
foot high door.

Clear a workspace area to unpack and organize box
and contents for assembly.

1. There are 4 boxes inside the carton. Each box is

numbered 1 - 4. Note that some openers will

contain the same parts and be packaged with
fewer boxes. Carefully remove the three

internal boxes (Labeled #1, 2, and 3) and place
them on the floor for easy access (Fig. 1-1).

These boxes contain assembly parts and the
contents are organized by assembly tasks. For
quick reference inside the lid of each box there is
a label illustrating the components inside.

2. Remove the motor power head and place it on
the floor for later use. Remove box #4 and
place it on the floor for later use.

FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

#4

Bag 0

Rail

Power head

Bag 2

Header Bracket

Bolts

Bolts

Bag 3Bag 1

5/16" Nuts

& Bolts

Header Bracket

Lag Srews

Box Label Example

FIG. 1-1 Internal boxes.

PN 37026501206 01/27/2012

9