General Semiconductor W10G, W08G, W06G, W04G, W01G Datasheet
...
W005G THRU W10G
0.220 (5.6)
0.160 (4.1)
0.388 (9.86)
0.348 (8.84)
0.032 (0.81)
0.028 (0.71)
1.0
(25.4)
MIN.
0.060 (1.52)
0.020 (0.51)
0.348 (8.84)
0.308 (7.82)
0.220 (5.6)
0.180 (4.6)
0.220 (5.6)
0.180 (4.6)
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
Reverse Voltage - 50 to 1000 Volts Forward Current - 1.5 Amperes
Case Style WOG
Dimensions in inches and (millimeters)
FEATURES
♦ Plastic material has Underwriters Laboratory Flammability
Recognition 94V-0
♦ This series is UL listed under the Recognized Component
Index, file number E54214
♦ Glass passivated chip junctions
♦ High case dielectric strength
♦ Typical IRless than 0.1µA
♦ High overload surge capability
♦ Ideal for printed circuit boards
♦ High temperature soldering guaranteed:
260°C/10 seconds, 0.375” (9.5mm) lead length,
5lbs (2.3kg) tension
MECHANICAL DATA
Case: Molded plastic body over passivated junctions
Terminals: Plated leads solderable per MIL-STD-750,
Method 2026
Mounting Position: Any
Weight: 0.04 ounce, 1.1 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified.
Maximum repetitive peak reverse voltage V
Maximum RMS voltage V
Maximum DC blocking voltage V
Maximum average forward rectified current at
0.375" (9.5mm) lead length at T
Peak forward surge current single sine-wave
superimposed on rated load (JEDEC Method)
Rating for fusing (t<8.3ms) I
Maximum instantaneous forward voltage drop
per leg at 1.0A
Maximum DC reverse current at rated T
DC blocking voltage per leg T
Typical junction capacitance per leg
Typical thermal resistance per leg
Operating junction temperature range T
Storage temperature range T
=25°C
A
(NOTE 2)
A
=125°C
A
(NOTE 1)
SYMBOLS W005G W01G W02G W04G W06G W08G W10G UNITS
RRM
RMS
DC
I
(AV)
I
FSM
2
t 10.0 A2sec
V
F
=25°C 5.0
R
R
I
R
C
J
ΘJA
ΘJL
J
STG
50 100 200 400 600 800 1000 Volts
35 70 140 2 80 420 560 700 Volts
50 100 200 400 600 800 1000 Volts
1.5 Amps
50.0 Amps
1.0 Volts
500.0
14.0 pF
36.0
11.0
-55 to +150 °C
-55 to +150 °C
µA
°C/W
NOTES:
(1) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
(2) Thermal resistance from junction to ambient and from junction to lead at 0.375" (9.5mm) lead length P.C.B. mounting
4/98
0.1 1 10 100
1
10
100
0.01 0.1 1 10 100
0.1
1
10
100
1
0
10
40
50
60
30
20
10
100
0.4 0.6 0.8 1.0 1.2 1.4 1.6
0.01
0.1
1
10
20
20 40 60 80 100 120 140
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
150
020406080100
0.01
0.1
1
10
50
RATINGS AND CHARACTERISTICS CURVES W005G THRU W10G
FIG.1 - DERATING CURVE
OUTPUT RECTIFIED CURRENT
60 H
Z
RESISTIVE OR
INDUCTIVE
LOAD
P.C.B.
CURRENT, AMPERES
AVERAGE FORWARD OUTPUT
CAPACITIVE LOADS
Ipk/IAV=5.0
Ipk/I
=10
AV
Ipk/I
=20
AV
0.22 x 0.22” (5.5 x 5.5mm)
COPPER PADS
AMBIENT TEMPERATURE, °C
FIG. 3 - TYPICAL FORWARD CHARACTERISTICS
TJ= 25°C
PULSE WIDTH=300µs
1% DUTY CYCLE
PER LEG
0.375”
(9.5mm)
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT PER LEG
AMPERES
PEAK FORWARD SURGE CURRENT,
1.0 CYCLE
NUMBER OF CYCLES AT 60 H
FIG. 4 - TYPICAL REVERSE CHARACTERISTICS
PER LEG
TJ=100°C
TA=25°C
SINGLE SINE-WAVE
(JEDEC Method)
Z
AMPERES
INSTANTANEOUS FORWARD CURRENT,
INSTANTANEOUS FORWARD VOLTAGE,
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
VOLTS
PER LEG
TJ=25°C
f=1.0 MHz
Vsig=50mVp-p
MICROAMPERES
INSTANTANEOUS REVERSE CURRENT,
TJ=25°C
PERCENT OF RATED PEAK REVERSE
FIG. 6 -TYPICAL TRANSIENT THERMAL IMPEDANCE
VOLTAGE, %
°C/W
JUNCTION CAPACITANCE, pF
REVERSE VOLTAGE, VOLTS
TRANSIENT THERMAL IMPEDANCE,
t, HEATING TIME, sec.
Loading...