General Semiconductor UG06D, UG06C, UG06B, UG06A Datasheet
UG06A THRU UG06D
1.0 (25.4)
MIN.
1.0 (25.4)
MIN.
0.125 (3.18)
0.115 (2.92)
0.100 (2.54)
0.090 (2.29)
0.025 (0.635)
0.023 (0.584)
DIA
DIA.
MINIATURE ULTRAFAST EFFICIENT PLASTIC RECTIFIER
Reverse Voltage - 50 to 200 Volts Forward Current - 0.6 Ampere
Case Style MPG06
Dimensions in inches and (millimeters)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified.
FEATURES
♦ Plastic package has Underwriters Laboratories
Flammability Classification 94V-0
♦ Ideally suited for use in very high frequency switching
power supplies, inver ters and as a free wheeling diode
♦ Ultrafast reverse
recovery times for high efficiency
♦ Soft recovery characteristics
♦ Excellent high temperature switching
♦ Glass passivated junction
♦ High temperature soldering guaranteed:
250°C/10 seconds, 0.375" (9.5mm) lead length,
5 lbs. (2.3kg) tension
MECHANICAL DATA
Case: Void free molded plastic body over passivated chip
Terminals: Plated axial leads, solderable per MIL-STD-750,
Method 2026
Polarity: Color band denotes cathode end
Mounting Position: Any
WeIght: 0.0064 ounce, 0.181 gram
SYMBOLS UG06A UG06B UG06C UG06D UNITS
Maximum repetitive peak reverse voltage V
Maximum RMS voltage V
Maximum DC blocking voltage V
Maximum average forward rectified current
0.375" (9.5mm) lead length at TL=75°C
Peak forward surge current
8.3 ms single half sine-wave superimposed I
on rated load (JEDEC Method) at T
=75°C
L
Maximum instantaneous forward voltage at 0.6A V
Maximum DC reverse current T
at rated DC blocking voltage T
Maximum reverse recovery time
(NOTE 1)
Maximum reverse recovery time T
(NOTE 2)
Maximum recovered stored charge T
(NOTE 2)
Typical junction capacitance
Typical thermal resistance
(NOTE 3)
(NOTE 4)
=25°C 5.0
A
=100°C
A
=25°C 25.0
J
TJ=100°C
=25°C 8.0
J
TJ=100°C
R
R
Operating junction and storage temperature range T
NOTES:
(1) Reverse recovery test conditions:I
and Q
(2) t
rr
(3) Measured at 1.0 MHZand applied reverse voltage of 4.0 Volts
(4) Thermal resistance from junction to ambient and junction to lead at 0.375" (9.5mm) lead length
rr
P.C.B.mounted with 0.2 x 0.2” (5.0 x 5.0mm) copper pads
measured at IF=0.6A:VR=30V, di/dt=50A/µs, Irr=10% I
=0.5A, IR=1.0A,Irr=0.25A
F
for meaurement of t
RM
, T
J
rr
4/98
RRM
RMS
DC
I
(AV)
FSM
I
R
t
rr
t
rr
Q
C
ΘJA
ΘJL
F
rr
J
STG
50 100 150 200 Volts
35 70 105 140 Volts
50 100 150 200 Volts
0.6 Amp
40.0 Amps
0.95 Volts
100.0
µA
15.0 ns
35.0
20.0
ns
nC
9.0 pF
97.0
28.0
°C/W
-55 to +150 °C
RATINGS AND CHARACTERISTIC CURVES UG06A THRU UG06D
0 25 50 75 100 125 150 175
0
0.15
0.3
0.45
0.6
0.75
0.9
110100
1
10
100
0.4 0.6 0.8 1.0 1.2 1.4 1.6
0.01
0.1
1
10
100
0 25 50 75 1 00 125 150 175
0
10
20
30
40
50
60
0.1 1 10 100
1
10
100
0 20 40 60 80 100
0.01
0.1
1
10
100
1,000
FIG. 1 - MAXIMUM FORWARD CURRENT
DERATING CURVES
RESISTIVE OR INDUCTIVE LOAD
0.375" (9.5mm) LEAD LENGTH
TL, LEAD TEMPERATURE
CURRENT, AMPERES
AVERAGE FORWARD RECTIFIED
TA, AMBIENT
TEMPERATURE
P.C.B. MOUNTED
0.2 x 0.2" (5.0 x 5.0mm)
COPPER PADS
TEMPERATURE, °C
FIG. 3 - TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS
TJ=100°C
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
TJ=75°C
8.3ms SINGLE HALF SINE-WAVE
(JEDEC Method)
AMPERES
PEAK FORWARD SURGE CURRENT,
NUMBER OF CYCLES AT 60 H
Z
FIG. 4 - TYPICAL REVERSE LEAKAGE
CHARACTERISTICS
INSTANTANEOUS FORWARD CURRENT,
AMPERES
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
PULSE WIDTH=300µs
1% DUTY CYCLE
FIG. 5 - REVERSE SWITCHING
CHARACTERISTICS
IF=0.6A
VR=30V
RECOVER Y TIME, nC/ns
RECOVERED pP CHARGE/REVERSE
di/dt=20A/µs
di/dt=50A/µs
di/dt=100A/µs
di/dt=150A/µs
di/dt=
di/dt=
di/dt=
JUNCTION TEMPERATURE °C
di/dt=
TJ=25°C
150A/µs
100A/µs
50A/µs
20A/µs
TJ=100°C
TJ=25°C
MICROAMPERES
INSTANTANEOUS REVERSE LEAKAGE CURRENT,
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
FIG. 6 - TYPICAL JUNCTION CAPACITANCE
TJ=25°C
f=1.0 MH
t
rr
Q
rr
Z
Vsig=50mVp-p
JUNCTION CAPACITANCE, pF
REVERSE VOLTAGE, VOLT S
Loading...