General Semiconductor GP10Y, GP10W, GP10J, GP10G, GP10V Datasheet

...

GP10A THRU GP10Y

0.107 (2.7)

0.080 (2.0)

0.034 (0.86)

0.028 (0.71)

DIA.

1.0 (25.4) MIN.

0.205 (5.2)

0.160 (4.1)

DIA.

NOTE:

Lead diameter is for suffix "E" part numbers

0.026 (0.66)

0.023 (0.58)

GLASS PASSIVATED JUNCTION RECTIFIER

Reverse Voltage - 50 to 1600 Volts Forward Current - 1.0 Ampere

DO-204AL

PATENTED*

Dimensions in inches and (millimeters)

Patent No.3,996,602 and brazed-lead assembly by Patent No. 3,930,306

Glass-plastic encapsulation is covered by

FEATURES

♦ Plastic package has

Underwriters Laboratory Flammability Classification 94V-0

♦ High temperature metallurgically bonded construction ♦ Glass passivated cavity-free junction ♦ Capable of meeting environmental standards of

MIL-S-19500

♦ 1.0 Ampere operation at TA=75°C and 55°C

with no thermal runaway

♦ Typical IRless than 0.1µA ♦ High temperature soldering guaranteed:

350°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension

MECHANICAL DATA

Case: JEDEC DO-204AL molded plastic over glass body Terminals: Plated axial leads, solderable per MIL-STD-750,

Method 2026

Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.012 ounce, 0.3 gram

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

Ratings at 25°C ambient temperature unless otherwise specified.

SYMBOLS A B D G J K M N Q T V W Y UNITS

Maximum repetitive peak reverse voltage V Maximum average forward rectified current

0.375" (9.5mm) lead length (

SEE FIG. 1

)

Peak forward surge current

8.3ms single half sine-wave superimposed on rated load (JEDEC Method)

Maximum instantaneous forward voltage at 1.0A V Maximum full load reverse current, full cycle

average, 0.375" (9.5mm) lead lengths at T Maximum DC reverse current T

at rated DC blocking voltage T Typical reverse recovery time Typical junction capacitance Typical thermal resistance Operating junction and storage temperature range T

NOTES:

(1) Reverse recovery test condition:IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient at 0.375" (9.5mm) lead lengths, P.C.B.mounted

4/98

(NOTE 1)

(NOTE 2)

(NOTE 3)

=75°C

=25°C 5.0

=125°C

RRM

(AV)

FSM

R(AV)

trr 2.0 µs

ΘJA

, T

STG

50 to 1600 Volts

(SEE FIG. 5)

Volts

1.0 Amp

30.0 25.0 Amps

1.1 1.2 1.3 Volts

30.0 µA

50.0

µA

8.0 7.0 5.0 pF

55.0 °C/W

-65 to +175 -65 to +150 °C

1100

5.0

1.1

1.5

1.6

0.1

0.6 0.7 0.8 0.9 1.0 1.2 1.3 1.4

0.01

20 40 60

140 160

180

1.0

0.8

0.6

0.4

0.2 0

80 100 120

0.1 1 10 100

1.0

100

0.001

0.01

0.1

020406080

AMPERES

0.375" (9.5mm) LEAD LENGTH

AVERAGE FORWARD RECTIFIED CURRENT,

RATINGS AND CHARACTERISTIC CURVES GP10A THRU GP10Y

FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT

FIG. 1 - FORWARD CURRENT DERATING CURVE

GP10A - GP10M

60 H

GP10N - GP10Y

AMBIENT TEMPERATURE, °C

FIG. 3 - TYPICAL INSTANTANEOUS FORWARD

CHARACTERISTICS

RESISTIVE OR INDUCTIVE LOAD

AMPERES

PEAK FORWARD SURGE CURRENT,

GP10N - GP10Y

NUMBER OF CYCLES AT 60 H

FIG. 4 - TYPICAL REVERSE

TJ=125°C

TJ=TJ max.

8.3ms SINGLE HALF SINE-WAVE (JEDEC Method)

GP10A - GP10M

CHARACTERISTICS

INSTANTANEOUS FORWARD CURRENT, AMPERES

INSTANTANEOUS FORWARD V OLTAGE, VOL TS

FIG. 5 - MAXIMUM REPETITIVE PEAK

REVERSE VOL TAGE,V

GP10A . . . . . . .50V

GP10B . . . . . .100V

GP10D . . . . . .200V

GP10G . . . . . .400V

GP10J . . . . . .600V

GP10K . . . . . .800V

GP10M . . . . .1000V

GP10N . . . . .1100V

GP10Q . . . . .1200V

GP10T . . . . .1300V

GP10V . . . . .1400V

GP10W . . . .1500V

GP10Y . . . . .1600V

RRM

TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE

GP10A to GP10J

GP10K to GP10Q

GP10T to GP10Y

JUNCTION CAPACITANCE pF

TJ=75°C

MICROAMPERES

INSTANTANEOUS REVERSE LEAKAGE CURRENT,

TJ=25°C

PERCENT OF RATED PEAK REVERSE VOLTAGE, %

FIG. 6 - TYPICAL JUNCTION CAPACITANCE

GP10A to GP10J

GP10K to GP10Q

GP10T to GP10Y

TJ=25°C f=1.0 MH

Vsig=50mVp-p

REVERSE VOLTA GE, VOLTS