General Semiconductor GP08J, GP08G, GP08D, GP08B, GP08A Datasheet

GP08A THRU GP08J

0.107 (2.7)

0.080 (2.0)

0.034 (0.86)

0.028 (0.71)

DIA.

1.0 (25.4) MIN.

0.205 (5.2)

0.160 (4.1)

DIA.

NOTE:

Lead diameter is for suffix "E" part numbers

0.026 (0.66)

0.023 (0.58)

GLASS PASSIVATED JUNCTION RECTIFIER

Reverse Voltage - 50 to 600 Volts Forward Current - 0.8 Ampere

DO-204AL

PATENTED*

Dimensions in inches and (millimeters)

Patent No.3,996,602 and brazed-lead assembly by Patent No.3,930,306

Glass-plastic encapsulation technique is covered by

FEATURES

♦ Plastic package has

Underwriters Laboratory Flammability Classification 94V-0

♦ High temperature metallurgically

bonded construction

♦ Glass passivated cavity-free junction ♦ Capable of meeting environmental standards of

MIL-S-19500

♦ 0.8 Ampere operation at TA=55°C with no thermal

runaway

♦ Typical IRless than 0.1µA ♦ High temperature soldering guaranteed:

350°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension

MECHANICAL DATA

Case: JEDEC DO-204AL molded plastic over glass body Terminals: Plated axial leads, solderable per MIL-STD-750,

Method 2026

Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.012 ounce, 0.3 gram

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

Ratings at 25°C ambient temperature unless otherwise specified.

Maximum repetitive peak reverse voltage V Maximum RMS voltage V Maximum DC blocking voltage V Maximum average forward rectified current

0.375" (9.5mm) lead length at T Peak forward surge current

8.3ms single half sine-wave superimposed on rated load (JEDEC Method) at T

Maximum instantaneous forward voltage at 0.8A V Maximum full load reverse current full cycle

average 0.375" (9.5mm) lead length at T Maximum DC reverse current T

at rated DC blocking voltage T Typical reverse recovery time Typical junction capacitance Typical thermal resistance Operating junction and storage temperature range T

NOTES:

(1) Measure on IF=0.5A, IR=1.0A, Irr= 0.25A (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient at 0.375" (9.5mm) lead length, P.C.B.mounted

4/98

(NOTE 1)

(NOTE 2)

(NOTE 3)

=55°C

=25°C 5.0

=125°C

SYMBOLS GP08A GP08B GP08D GP08G GP08J UNITS

RRM RMS

(AV)

FSM

R(AV)

I t

ΘJA

, T

STG

50 100 200 400 600 Volts 35 70 140 280 420 Volts 50 100 200 400 600 Volts

0 .8 Amp

25.0 Amps

1.3 Volts

30.0 µA

50.0

µA

2.0 µs

8.0 pF

55.0 °C/W

-65 to +175 °C

100

5.0

0.1

10 100

0.4 0.6 1.2 1.4

0.1

0.8

100

100 120 140 160 180

0.2

0.4

0.6

0.8

1.0

60 80

20 40 60 80 100

0.01

0.1

0.01 0.1 1 10 100

0.1

100

RATINGS AND CHARACTERISTIC CURVES GP08A THRU GP08J

AMPERES

AVERAGE FORWARD CURRENT,

FIG. 1 - FORWARD CURRENT DERATING CURVE

0.375" (9.5mm) LEAD LENGTH

FIG. 3 - TYPICAL INSTANTANEOUS

FORWARD CHARACTERISTICS

60 HZRESISTIVE OR INDUCTIVE LOAD

AMBIENT TEMPERATURE, °C

TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE

PEAK FORWARD SURGE CURRENT,

AMPERES

FIG. 2 - MAXIMUM NON-REPETITIVE PEAK

FORWARD SURGE CURRENT

TJ=TJmax.

8.3ms SINGLE HALF SINE-WAVE (JEDEC Method)

NUMBER OF CYCLES AT 60 Hz

FIG. 4 - TYPICAL REVERSE CHARACTERISTICS

TJ=100°C

AMPERES

INSTANTANEOUS FORWARD CURRENT,

INSTANTANEOUS FORWARD V OLTAGE, VOL TS

FIG. 5 - TYPICAL JUNCTION CAPACITANCE

JUNCTION CAPACITANCE, pF

REVERSE VOLTA GE, VOLTS

TJ=25°C f=1.0 MH

Vsig=50mVp-p

MICROAMPERES

INSTANTANEOUS REVERSE CURRENT,

FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE

TJ=25°C

PERCENT OF RATED PEAK REVERSE

VOLTAGE, %

TRANSIENT THERMAL IMPEDANCE (°C/W)

t, PULSE DURATION, sec