General Semiconductor GBU6K, GBU6M, GBU6J, GBU6G, GBU6A Datasheet
...
GBU6A THRU GBU6M
0.125 (3.2) x 45
o
CHAMFER
0.085 (2.16)
0.065 (1.65)
0.020 R (TYP.)
0.880 (22.3)
0.860 (21.8)
0.100 (2.54)
0.085 (2.16)
0.160 (4.1)
0.140 (3.5)
0.075
(1.9)
R.
0.080
0.060
(2.03)
(1.52)
0.050 (1.27)
0.040 (1.02)
0.080
0.065
(2.03)
(1.65)
0.210
0.190
(5.33)
(4.83)
Polarity shown on front side of case, positive lead by beveled corner
0.140 (3.56)
0.130 (3.30)
9
o
TYP.
5
o
TYP.
0.085 (2.16)
0.075 (1.90)
0.022 (0.56)
0.018 (0.46)
0.310 (7.9)
0.290 (7.4)
0.740 (18.8)
0.720 (18.3)
0.710 (18.0)
0.690 (17.5)
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
Reverse Voltage - 50 to 1000 Volts Forward Current - 6.0 Amperes
FEATURES
♦ Plastic package has Underwriters Laboratory Flammability
Case Style GBU
Dimensions in inches and (millimeters)
Classification 94V-0
♦ This series is UL listed under the Recognized Component
Index, file number E54214
♦ High case dielectric
strength of 1500 V
RMS
♦ Ideal for printed circuit boards
♦ Glass passivated chip junctions
♦ High surge overload rating
♦ High temperature soldering guaranteed:
260°C/10 seconds, 0.375" (9.5mm) lead length,
5lbs. (2.3kg) tension
MECHANICAL DATA
Case: Molded plastic body over passivated chip
Terminals: Plated leads solderable per MIL-STD-750,
Method 2026
Mounting Position: Any
Mounting T orque: 5 in. - lb.max.
Weight: 0.15 ounce, 4.0 grams
(NOTE 2)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified.
SYMBOLS 6A 6B 6D 6G 6J 6K 6M UNITS
Maximum repetitive peak reverse voltage V
Maximum RMS Voltage V
Maximum DC blocking voltage V
Maximum average forward rectified
output current at T
=100°C
C
(NOTE 1, 2)
Peak forward surge current single sine-wave
superimposed on rated load (JEDEC Method) T
=150°C
J
Rating for fusing (t<8.3ms) I
Maximum instantaneous forward voltage drop
per leg at 6.0A
Maximum DC reverse current at T
rated DC blocking voltage per leg T
Typical junction capacitance per leg
Typical thermal resistance per leg R
(NOTE 1, 2)
Operating junction and storage temperature range T
NOTES:
(1) Units case mounted on 2.6 x 1.4 x 0.06" thick (6.5 x 3.5 x 0.15 cm) Al. Plate heatsink
(2) Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screws
(3) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
(NOTE 3)
=25°C 5.0
A
=125°C
A
RRM
RMS
DC
I
(AV)
I
FSM
2
t 127.0 A2sec
V
F
I
R
C
J
ΘJA
R
ΘJC
, T
J
STG
GBU GBU GBU GBU GBU GBU GBU
50 100 200 400 600 800 1000 Volts
35 70 140 280 420 560 700 Volts
50 100 200 400 600 800 1000 Volts
6.0 Amps
175.0 Amps
1.0 Volts
500.0
211.0 94.0 pF
7.4
2.2
-55 to +150 °C
µA
°C/W
4/98
0 50 100 150
0
2.0
4.0
6.0
110100
25
50
75
100
125
150
175
0.4 0.6 0.8 1.0 1.2 1.4 1.6
0.01
0.1
1
10
100
0.1 1 10 100
10
100
1,000
100
0.01 0.1 1 10 100
0.1
1
10
020406080100
0.01
0.1
1
10
100
RATINGS AND CHARACTERISTICS CURVES GBU6A THRU GBU6M
FIG. 1 - DERATING CURVE OUTPUT RECTIFIED
HEAT-SINK MOUNTING,
2.6 x 1.4 x 0.06” THK
(6.5” x 3.5” x .15cm)
AL. PLATE
CURRENT
AMPERES
60 HZRESISTIVE OR INDUCTIVE LOAD
AVERAGE FORWARD OUTPUT CURRENT,
FIG. 3 - TYPICAL FORWARD CHARACTERISTICS
CASE TEMPERATURE, °C
PER LEG
TJ=25°C
PULSE WIDTH=300µs
1% DUTY CYCLE
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD
SURGE CURRENT PER LEG
SINGLE SINE-WAVE
(JEDEC Method)
TJ=150°C
AMPERES
PEAK FORWARD SURGE CURRENT,
1.0 CYCLE
NUMBER OF CYCLES AT 60 H
Z
FIG. 4 - TYPICAL REVERSE LEAKAGE
CHARACTERISTICS PER LEG
TJ=125°C
AMPERES
INSTANTANEOUS FORWARD CURRENT,
INSTANTANEOUS FORWARD VOLTAGE,
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
VOLTS
PER LEG
TJ=25°C
f=1.0 MHz
Vsig=50mVp-p
MICROAMPERES
INSTANTANEOUS REVERSE CURRENT,
TJ=25°C
PERCENT OF RATED PEAK REVERSE
°C\W
FIG. 6 - TYPICAL TRANSIENT THERMAL
VOLTAGE, %
IMPEDANCE
50 - 400V
600 - 1000V
JUNCTION CAPACITANCE, pF
50 - 400V
600 - 1000V
REVERSE VOLTAGE, VOLTS
TRANSIENT THERMAL IMPEDANCE,
t, HEATING TIME, sec.
Loading...