General Semiconductor GBPC6005, GBPC610, GBPC608, GBPC606, GBPC604 Datasheet

GBPC6005 THRU GBPC610

HOLE FOR
#6 SCREW

0.158 (4.01)

0.142 (3.61)
DIA.

0.128 (3.25)

0.048 (1.22)

0.200 (5.08)

0.160 (4.06)

0.750

(19.05)

MIN.

0.040 (1.02) TYP.

0.094 (2.4) x 45 degrees

0.445 (11.30)

0.405 (10.29)

0.630 (16.00)

0.590 (14.98)

AC

AC

Polarity shown on side of case:

Positive lead by beveled corner

0.445 (11.30)

0.405 (10.29)

0.630 (16.00)

0.590 (14.98)

DIA.

0.042(1.07)

0.038(0.96)

GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER

Reverse Voltage - 50 to 1000 Volts Forward Current - 6.0 Amperes

Case Style GBPC

Dimensions in inches and (millimeters)

FEATURES

♦ Plastic package has carries Underwriters Laboratory

Flammability Classification 94V-0

♦ This series is UL listed under recognized under Component

Index, file number E54214

♦ Glass passivated chip junctions
♦ High case dielectric strength of 1500 V

RMS

♦ Typical IRless than 0.5µA
♦ High forward surge current capability
♦ Ideal for printed circuit boards
♦ High temperature soldering guaranteed:

260°C/10 seconds at 5lbs. (2.3 kg) tension

MECHANICAL DATA

Case: Molded plastic body over passivated junction
Terminals: Plated leads solderable per MIL-STD-750,

Method 2026

Mounting Position: Any
Mounting T orque: 5.0 in. - lb. max.
Weight: 0.1 ounce, 2.8 grams

(NOTE 1)

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

Ratings at 25°C ambient temperature unless otherwise specified.

SYMBOLS 6005 601 602 604 606 608 610 UNITS

Maximum repetitive peak reverse voltage V
Maximum RMS bridge input voltage V
Maximum DC blocking voltage V
Maximum average forward T

rectified output current at T
Peak forward surge current single sine-wave

superimposed on rated load (JEDEC Method)
Rating for fusing (t<8.3ms) I

=50°C

C
A

=40°C

(NOTE1, 2)

(NOTE 3)

Maximum instantaneous forward voltage drop
per leg at 3.0 Amperes

Maximum DC reverse current at rated T
DC blocking voltage per leg T

Typical junction capacitance per leg
Typical thermal resistance per leg

Operating junction temperature range T
Storage temperature range T

NOTES:

(1) Bolt down on heat-sink with silicone thermal compound between bridge and mounting surface for maximum heat transfer with #6 screw
(2) Unit mounted on 5.5 x 6.0 x 0.11" thick (14 x 15 x 0.3cm) Al. Plate
(3) Unit mounted on P.C.B. at 0.375" (9.5mm) lead length with 0.5 x 0.5" (12 x 12mm) copper pads
(4) Measured at 1 MHz and applied reverse voltage of 4.0 Volts

(NOTE 4)

A
A

(NOTE 3)
(NOTE 2)

=25°C 5.0
=125°C

I

I

R
R

RRM
RMS

DC

(AV)

FSM

V

I

C

ΘJA
ΘJC

STG

GBPC GBPC GBPC GBPC GBPC GBPC GBPC

50 100 200 400 600 800 1000 Volts
35 70 140 2 80 420 560 700 Volts
50 100 200 400 600 800 1000 Volts

6.0

3.0

175.0 Amps

2

t 127.0 A2sec

F

R

J

186.0 90.0 pF

1.0 Volts

500.0

22.0

7.3

J

-55 to +150 °C

-55 to +150 °C

Amps

µA

°C/W

4/98

0 50 100 150

0

2.0

4.0

6.0

8.0

110100

50

75

100

125

150

175

200

10

0.4

1.0 1.8

0.01

0.1

1

100

0.01 0.1 1 10 100

0.1

1

10

100

0.1 1 10 100

10

100

1,000

0.6 0.8 1.2

1.61.4

020406080100

0.1

1

10

100

500

RATINGS AND CHARACTERISTICS CURVES GBPC6005 THRU GBPC610

FIG. 1 - DERATING CURVE OUTPUT RECTIFIED

CURRENT

CASE TEMPERATURE, T
HEAT-SINK MOUNTING,

C

5.5 x 6.0 x 0.11” THK
(14 x 1.5” x 0.3cm)
AL. PLATE

60 HZRESISTIVE OR
INDUCTIVE LOAD

AMPERES

AVERAGE FORWARD OUTPUT CURRENT,

AMBIENT TEMPERATURE, T

P.C.B. MOUNTING,

0.375” (9.5mm) LEAD LENGTH

A

TEMPERATURE, °C

FIG. 4 - TYPICAL FORWARD

CHARACTERISTICS PER LEG

TJ=25°C
PULSE WIDTH=300µs
1% DUTY CYCLE

FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD

SURGE CURRENT PER LEG

TJ=TJmax.
SINGLE HALF SINE-WAVE
(JEDEC Method)

AMPERES

PEAK FORWARD SURGE CURRENT,

1.0 CYCLE

NUMBER OF CYCLES AT 60 Hz

FIG. 3 - TYPICAL REVERSE LEAKAGE

CHARACTERISTICS PER LEG

TA=125°C

TJ=100°C

AMPERES

INSTANTANEOUS FORWARD CURRENT,

INSTANTANEOUS FORWARD VOLTAGE,

FIG. 5 - TYPICAL JUNCTION CAPACITANCE

VOLTS

PER LEG

TJ=25°C
f=1.0 MHz
Vsig=50mVp-p

MICROAMPERES

INSTANTANEOUS REVERSE CURRENT,

TJ=25°C

PERCENT OF RATED PEAK REVERSE

VOLTAGE, %

FIG. 6 - TYPICAL TRANSIENT THERMAL

IMPEDANCE

°C/W

JUNCTION CAPACITANCE, pF

50 - 400V

600 - 1000V

REVERSE VOLTAGE, VOLTS

TRANSIENT THERMAL IMPEDANCE,

t, HEATING TIME, sec.