General Semiconductor GBPC110, GBPC108, GBPC106, GBPC104, GBPC102 Datasheet
...
GBPC1005 THRU GBPC110
HOLE FOR
#6 SCREW
0.158 (4.01)
0.142 (3.61)
DIA.
0.128 (3.25)
0.048 (1.22)
0.200 (5.08)
0.160 (4.06)
0.750
(19.05)
MIN.
0.040 (1.02) TYP.
0.094 (2.4) x 45 degrees
0.445 (11.30)
0.405 (10.29)
0.630 (16.00)
0.590 (14.98)
AC
AC
Polarity shown on side of case:
Positive lead by beveled corner
0.445 (11.30)
0.405 (10.29)
0.630 (16.00)
0.590 (14.98)
0.032 (0.81)
0.028 (0.71)
DIA.
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
Reverse Voltage - 50 to 1000 Volts Forward Current - 3.0 Amperes
Case Style GBPC1
Dimensions in inches and (millimeters)
FEATURES
♦ Plastic package has Underwriters Laboratory Flammability
Classification 94V-0
♦ This series is UL listed under Recognized Component Index,
file number E54214
♦ Glass passivated chip junctions
♦ High case dielectric with standing voltage of 1500 V
RMS
♦ Typical IRless than 0.1µA
♦ High surge current capability
♦ Ideal for printed circuit boards
♦ High temperature soldering guaranteed:
260°C/10 seconds, 0.375" (9.5mm) lead length,
5lbs. (2.3kg) tension
MECHANICAL DATA
Case: Molded plastic body over passivated junctions
Terminals: Plated leads solderable per MIL-STD-750,
Method 2026
Mounting Position: Any
Mounting T orque: 5.0 in. - lb. max.
Weight: 0.1 ounce, 2.8 grams
(NOTE 1)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified.
SYMBOLS 1005 101 102 104 106 108 110 UNITS
Maximum repetitive peak reverse voltage V
Maximum RMS bridge input voltage V
Maximum DC blocking voltage V
Maximum average forward T
rectified output current at T
Peak forward surge current single sine-wave
superimposed on rated load (JEDEC Method) T
Rating for fusing (t<8.3ms) I
Maximum instantaneous forward voltage drop
per leg at 1.5 Amperes
Maximum DC reverse current at rated T
DC blocking voltage per leg T
Typical junction capacitance per leg
Typical thermal resistance per leg
Operating junction and storage temperature range T
NOTES:
(1) Bolt down on heat-sink with silicone thermal compound between bridge and mounting surface for maximum heat transfer with #6 screw
(2) Unit mounted on 4.0 x 4.0 x 0.11" thick (10.5 x 10.5 x 0.3cm) Al. Plate
(3) Unit mounted on P.C.B. at 0.375" (9.5mm) lead length with 0.5 x 0.5" (12 x 12mm) copper pads
(4) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
=60°C
C
=25°C
A
(NOTE 4)
(NOTE 2)
(NOTE 2)
(NOTE 3)
=60°C
C
= 25°C 5.0
A
=125°C
A
RRM
RMS
DC
I
(AV)
I
FSM
V
I
C
R
ΘJA
R
ΘJC
J,TSTG
GBPC GBPC GBPC GBPC GBPC GBPC GBPC
50 100 200 400 600 800 1000 Volts
35 70 140 280 420 560 700 Volts
50 100 200 400 600 800 1000 Volts
3.0
2.0
60.0 Amps
2
t 15.0 A2sec
F
R
J
1.0 Volts
500.0
21.0 pF
12.0
8.0
-55 to +150 °C
Amps
µA
°C/W
4/98
050100150
0
1.0
2.0
3.0
4.0
5.0
0.1 1.0 10 100
1
10
100
0.01 0.1 1 10 100
0.1
1
10
100
1 10 100
0
10
20
30
40
50
60
0.4 0.6 0.8 1.0 1.2 1.4 1.6
0.01
0.1
1
10
20
020406080
0.01
0.1
1
10
50
100
RATINGS AND CHARACTERISTICS CURVES GBPC1005 THRU GBPC110
FIG. 1 - DERATING CURVE OUTPUT RECTIFIED
CURRENT
CASE TEMPERATURE,
TCHEAT-SINK
MOUNTING,
4.0 x 4.0 x 0.11” THK
(10.5 x 10.5 x 0.3cm)
CURRENT, AMPERES
AMBIENT TEMPERATURE, T
AVERAGE FORWARD OUTPUT
P.C.B. MOUNTING
0.375” (9.5mm) LEAD LENGTH
AMBIENT TEMPERATURE, °C
A
AL. PLATE
60 H
Z
RESISTIVE OR
INDUCTIVE LOAD
FIG. 3 - TYPICAL FORWARD CHARACTERISTICS
PER LEG
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT PER LEG
TC=60°C
SINGLE SINE-WAVE
(JEDEC METHOD)
AMPERES
PEAK FORWARD SURGE CURRENT,
1.0 CYCLE
NUMBER OF CYCLES AT 60 H
FIG. 4 - TYPICAL REVERSE LEAKAGE
CHARACTERISTICS PER LEG
Z
AMPERES
INSTANTANEOUS FORWARD CURRENT,
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
PER LEG
TJ=25°C
PULSE WIDTH=300µs
1% DUTY CYCLE
TJ=25°C
f=1.0 MHz
Vsig=50mVp-p
MICROAMPERES
INSTANTANEOUS REVERSE CURRENT,
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE
TJ=125°C
TJ=25°C
PER LEG
JUNCTION CAPACITANCE, pF
REVERSE VOLTAGE, VOLTS
°C/W
TRANSIENT THERMAL IMPEDANCE,
t, HEATING TIME, sec.
Loading...