General Semiconductor G5SBA20 Datasheet
G5SBA20 AND G5SBA60
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
Reverse Voltage - 200 and 600 Volts Forward Current - 6.0 Amperes
FEATURES
¨ Plastic package has Underwriters Laboratory Flammability
Classification 94V-0
¨ This series is UL listed under the Recognized Component
Index, file number E54214
¨ High case dielectric
strength of 1500 V
RMS
¨ Ideal for printed circuit boards
¨ Glass passivated chip junction
¨ High surge current capability
¨ High temperature soldering guaranteed:
260¡C/10 seconds, 0.375 (9.5mm) lead length,
5lbs. (2.3kg) tension
MECHANICAL DATA
Case: Molded plastic body over passivated junctions
Terminals: Plated leads solderable per MIL-STD-750,
Method 2026
Mounting Position: Any
(NOTE 3)
Mounting Torque: 5 in. - lb. max.
Weight: 0.15 ounce, 4.0 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25¡C ambient temperature unless otherwise specified.
SYMBOLS G5SBA20 G5SBA60 UNITS
Maximum repetitive peak reverse voltage V
RRM
200 600 Volts
Maximum RMS voltage V
RMS
140 420 Volts
Maximum DC blocking voltage V
DC
200 600 Volts
Maximum average forward rectified T
C
=100¡C
(NOTE 1)
6.0
output current at T
A
=25¡C
(NOTE 2)
I
(AV)
2.8
Amps
Peak forward surge current single sine-wave
superimposed on rated load (JEDEC Method)
I
FSM
150 Amps
Rating for fusing (t<8.3ms) I
2
t60A
2
sec
Maximum instantaneous forward voltage drop
per leg at 3.0A
V
F
1.05 Volts
Maximum DC reverse current at T
A
=25¡C 5.0
rated DC blocking voltage per leg T
A
=125¡C
I
R
500
mA
Typical thermal resistance per leg
(NOTE 2)
R
QJA
22
(NOTE 1)
R
QJC
3.4
¡C/W
Operating junction and storage temperature range T
J
, T
STG
-55 to +150 ¡C
NOTES:
(1) Unit case mounted on Al plate heatsink.
(2) Units mounted on P.C.B. with 0.5 x 0.5" (12 x 12mm) copper pads and 0.375" (9.5mm) lead length
(3) Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw
Dimensions in inches and (millimeters)
Case Style GBU
Polarity shown on front side of case, positive lead beveled corner.
If preferred, marking may be on reverse side of case.
Lead forming option with 10mm-7.5mm-7.5mm spacing is available.
2/24/99
NEW PRODUCT NEW PRODUCT NEW PRODUCT
0.020 R (TYP.)
0.310 (7.9)
0.290 (7.4)
0.085 (2.16)
0.065 (1.65)
0.100 (2.54)
0.085 (2.16)
0.880 (22.3)
0.860 (21.8)
0.125 (3.2) x 45
0.160 (4.1)
0.140 (3.5)
0.075
(1.9)
CHAMFER
0.080
R.
0.060
0.050 (1.27)
0.040 (1.02)
(2.03)
(1.52)
0.140 (3.56)
o
0.740 (18.8)
0.720 (18.3)
0.710 (18.0)
0.690 (17.5)
0.130 (3.30)
o
9
TYP.
o
5
TYP.
0.085 (2.16)
0.075 (1.90)
0.065
(5.33)
0.210
Polarity shown on front side of case, positive lead by beveled corner
(4.83)
0.190
(2.03)
0.080
(1.65)
0.022 (0.56)
0.018 (0.46)
RATINGS AND CHARACTERISTICS CURVES G5SBA20 THRU G5SBA60
FIG. 1 - DERATING CURVE OUTPUT
RECTIFIED CURRENT
TEMPERATURE, ¡C
P.C.B. MOUNTING, T
A
HEATSINK MOUNTING, T
C
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
INSTANTANEOUS REVERSE CURRENT, MICROAMPERES
TJ=25¡C
PULSE WIDTH=300ms
1% DUTY CYCLE
FIG. 3 - TYPICAL FORWARD CHARACTERISTICS
PER LEG
INSTANTANEOUS FORWARD CURRENT,
AMPERES
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
PER LEG
REVERSE VOLTAGE, VOLTS
TJ=25°C
f=1.0 MH
Z
Vsig=50mVp-p
TJ=25¡C
AVERAGE FORWARD OUTPUT
CURRENT, AMPERES
FIG. 4 - TYPICAL REVERSE CHARACTERISTICS
PER LEG
NUMBER OF CYCLES AT 60 Hz
PEAK FORWARD SURGE CURRENT,
AMPERES
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT PER LEG
TJ=125¡C
FIG. 6 - TYPICAL TRANSIENT THERMAL
IMPEDANCE
TRANSIENT THERMAL IMPEDANCE,
¡C/W
t, HEATING TIME, sec.
TJ=TJ max.
SINGLE SINE-WAVE
(JEDEC Method)
1.0 CYCLE
JUNCTION CAPACITANCE, pF
8.0
6.0
4.0
2.0
0
0
50
100
10
100
150
150
100
50
0
1
10
500
100
10
100
1,000
100
1
0.1
0.01
0.4 0.6 0.8 1.0 1.2 1.4 1.6
1
0.1
0.01
20
0
100
10
1
60
40
100
80
10
0.1
1
10
100
0.1
0.01
0.1
1
10
100
Loading...