BZW04P-5V8 THRU BZW04-376
TRANSZORB™ TRANSIENT VOLTAGE SUPPRESSOR
Stand-off Voltage - 5.8 to 376 Volts Peak Pulse Power - 400 Watts
FEATURES
♦ Plastic package has Underwriters Laboratory
Flammability Classification 94V-0
♦ Glass passivated chip junction
♦ 400W peak pulse power
capability with a 10/1000µs waveform,
repetition rate (duty cycle): 0.01%
♦ Excellent clamping
capability
♦ Low incremental surge resistance
♦ Fast response time: typically less
than 1.0 ps from 0 Volts to V
(BR)
for uni-
directional and 5.0ns for bi-directional types
♦ Typical IDless than 1µA above 10V rating
♦ High temperature soldering guaranteed:
265°C/10 seconds, 0.375" (9.5mm) lead length,
5lbs. (2.3 kg) tension
MECHANICAL DATA
Case: JEDEC DO-204AL molded plastic over passivated
junction
Terminals: Plated axial leads, solderable per MIL-STD-750,
Method 2026
Polarity: For unidirectional types the color band denotes
the cathode, which is postitive with respect to the anode
under normal TVS operation
Mounting Position: Any
Weight: 0.012 ounce, 0.3 gram
DEVICES FOR BIDIRECTIONAL APPLICATIONS
For bi-directional use add suffix Letter "B" (e.g. BZW04P-6V4B).
Electrical characteristics apply in both directions.
MAXIMUM RATINGS AND CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified.
SYMBOL VALUE UNITS
Peak pulse power dissipation with a 10/1000µs waveform
(NOTE 1, FIG. 1)
P
PPM
Minimum 400 Watts
Peak pulse current with a 10/1000µs waveform
(NOTE 1)
I
PPM SEE TABLE 1
Amps
Steady state power dissipation at T
L
=75°C
lead lengths, 0.375” (9.5mm)
(NOTE 2)
P
M(AV)
1.0 Watts
Peak forward surge current, 8.3ms single half
Sine-wave superimposed on rated load
(JEDEC Method)
(NOTE 3)
unidirectional only
I
FSM
40.0 Amps
Maximum instantaneous forward voltage at 25A
(NOTE 4)
uni-directional only
V
F
3.5/5.0 Volts
Operating junction and storage temperature range T
J
, T
STG
-55 to +175 °C
NOTES:
(1) Non-repetitive current pulse, per Fig. 3 and derated above T
A
=25°C per Fig. 2
(2) Mounted on copper pad area of 1.6 x 1.6” (40 x 40mm) per Fig. 5
(3) 8.3ms single half sine-wave or equivalent square wave, duty cycle=4 pulses per minute maximum
(4) V
F
=3.5V max. for devices of V
(BR)
≤220V and VF=5.0 Volt max. for devices of V
(BR)
>220V
1/5/98
DO204AL
0.107 (2.7)
0.080 (2.0)
0.034 (0.86)
0.028 (0.71)
DIA.
1.0 (25.4)
MIN.
1.0 (25.4)
MIN.
0.205 (5.2)
0.160 (4.1)
DIA.
NOTE:
Lead diameter is for suffix "E" part numbers
0.026 (0.66)
0.023 (0.58)
Dimensions are in inches
and
(millimeters)
ELECTRICAL CHARACTERISTICS at (T
A
=25°C unless otherwise noted) TABLE 1
Maximum
Breakdown Voltage Maximum Peak Pulse Maximum Maximum
V
(BR)
Stand-off Reverse Current Clamping Temperature
Volts
(NOTE 1)
Test Voltage Leakage I
PPM
Voltage at Coefficient
Current V
WM
at V
WM
(Amps) I
PPM
of V
(BR)
Device Type MIN MAX
at I
T
(Volts) ID (µA)
(NOTE 2)
VC (Volts) (% / C)
(mA)
(NOTE4)
BZW04P5V8 6.45 7.48 10.0 5.80 1000 38.0 10.5 0.057
BZW04-5V8 6.45 7.14 10.0 5.80 1000 38.0 10.5 0.057
BZW04P6V4 7.13 8.25 10.0 6.40 500 35.4 11.3 0.061
BZW04-6V4 7.13 7.88 10.0 6.40 500 35.4 11.3 0.061
BZW04P7V0 7.79 9.02 10.0 7.02 200 33.0 12.1 0.065
BZW04-7V0 7.79 8.61 10.0 7.02 200 33.0 12.1 0.065
BZW04P7V8 8.65 10.0 1.0 7.78 50.0 30.0 13.4 0.068
BZW04-7V8 8.65 9.55 1.0 7.78 50.0 30.0 13.4 0.073
BZW04P8V5 9.50 11.0 1.0 8.55 10.0 27.6 14.5 0.073
BZW04-8V5 9.50 10.5 1.0 8.55 10.0 27.6 14.5 0.075
BZW04P9V4 10.5 12.1 1.0 9.4 5.0 25.7 15.6 0.075
BZW04-9V4 10.5 11.6 1.0 9.4 5.0 25.7 15.6 0.075
BZW0P10 11.4 13.2 1.0 10.2 5.0 24.0 16.7 0.078
BZW04-10 11.4 12.6 1.0 10.2 5.0 24.0 16.7 0.078
BZW04P11 12.4 14.3 1.0 11.1 5.0 22.0 18.2 0.081
BZW04-11 12.4 13.7 1.0 11.1 5.0 22.0 18.2 0.081
BZW04P13 14.3 16.5 1.0 12.8 5.0 19.0 21.2 0.084
BZW04-13 14.3 15.8 1.0 12.8 5.0 19.0 21.2 0.084
BZW04P14 15.2 17.6 1.0 13.6 5.0 17.8 22.5 0.086
BZW04-14 15.2 16.8 1.0 13.6 5.0 17.8 22.5 0.086
BZW04P15 17.1 19.8 1.0 15.3 5.0 16.0 25.2 0.088
BZW04-15 17.1 18.9 1.0 15.3 5.0 16.0 25.2 0.088
BZW04P17 19.0 22.0 1.0 17.1 5.0 14.5 27.7 0.090
BZW04-17 19.0 21.0 1.0 17.1 5.0 14.5 27.7 0.090
BZW04P19 20.9 24.2 1.0 18.8 5.0 13.0 30.6 0.092
BZW04-19 20.9 23.1 1.0 18.8 5.0 13.0 30.6 0.092
BZW04P20 22.8 26.4 1.0 20.5 5.0 12.0 33.2 0.094
BZW04-20 22.8 25.2 1.0 20.5 5.0 12.0 33.2 0.094
BZW04P23 25.7 29.7 1.0 23.1 5.0 10.7 37.5 0.096
BZW04-23 25.7 28.4 1.0 23.1 5.0 10.7 37.5 0.096
BZW04P26 28.5 33.0 1.0 25.6 5.0 9.6 41.5 0.097
BZW04-26 28.5 31.5 1.0 25.6 5.0 9.6 41.5 0.097
BZW04P28 31.4 36.3 1.0 28.2 5.0 8.8 45.7 0.098
BZW04-28 31.4 34.7 1.0 28.2 5.0 8.8 45.7 0.098
BZW04P31 34.2 39.6 1.0 30.8 5.0 8.0 49.9 0.099
BZW04-31 34.2 37.8 1.0 30.8 5.0 8.0 49.9 0.099
BZW04P33 37.1 42.9 1.0 33.3 5.0 7.4 53.9 0.100
BZW04-33 37.1 41.0 1.0 33.3 5.0 7.4 53.9 0.100
BZW04P37 40.9 47.3 1.0 36.8 5.0 6.7 59.3 0.101
BZW04-37 40.9 45.2 1.0 36.8 5.0 6.7 59.3 0.101
BZW04P40 44.7 51.7 1.0 40.2 5.0 6.2 64.8 0.101
BZW04-40 44.7 49.4 1.0 40.2 5.0 6.2 64.8 0.101
BZW04P44 48.5 56.1 1.0 43.6 5.0 5.7 70.1 0.102
BZW04-44 48.5 53.6 1.0 43.6 5.0 5.7 70.1 0.102
BZW04P48 53.2 61.6 1.0 47.8 5.0 5.2 77.0 0.103
BZW04-48 53.2 58.8 1.0 47.8 5.0 5.2 77.0 0.103
ELECTRICAL CHARACTERISTICS at (T
A
=25°C unless otherwise noted) TABLE 1 (Cont’d)
Maximum
Breakdown Voltage Maximum Peak Pulse Maximum Maximum
V
(BR)
Stand-off Reverse Current Clamping Temperature
Volts
(NOTE 1)
Test Voltage Leakage I
PPM
Voltage at Coefficient
Current V
WM
at V
WM
(Amps) I
PPM
of V
(BR)
Device Type MIN MAX
at I
T
(Volts) ID (µA)
(NOTE 2)
VC (Volts) (% / C)
(mA)
(NOTE4)
BZW04P53 58.9 68.2 1.0 53.0 5.0 4.7 85.0 0.104
BZW04-53 58.9 65.1 1.0 53.0 5.0 4.7 85.0 0.104
BZW04P58 64.6 74.8 1.0 58.1 5.0 4.3 92.0 0.104
BZW04-58 64.6 71.4 1.0 58.1 5.0 4.3 92.0 0.104
BZW04P64 71.3 82.5 1.0 64.1 5.0 3.9 103 0.105
BZW04-64 71.3 78.8 1.0 64.1 5.0 3.9 103 0.105
BZW04P70 77.9 90.2 1.0 70.1 5.0 3.5 113 0.105
BZW04-70 77.9 86.1 1.0 70.1 5.0 3.5 113 0.105
BZW04P78 86.5 100 1.0 78.0 5.0 3.2 125 0.105
BZW04-78 86.5 95.5 1.0 78.0 5.0 3.2 125 0.105
BZW04P85 95.0 110 1.0 85.5 5.0 2.9 137 0.106
BZW04-85 95.0 105 1.0 85.5 5.0 2.9 137 0.106
BZW04P94 105 121 1.0 94.0 5.0 2.6 152 0.107
BZW04-94 105 116 1.0 94.0 5.0 2.6 152 0.107
BZW04P102 114 132 1.0 102 5.0 2.4 165 0.107
BZW04-102 114 126 1.0 102 5.0 2.4 165 0.107
BZW04P110 124 143 1.0 111 5.0 2.2 179 0.107
BZW04-110 124 137 1.0 111 5.0 2.2 179 0.107
BZW04P128 143 165 1.0 128 5.0 2.0 207 0.108
BZW04-128 143 158 1.0 128 5.0 2.0 207 0.108
BZW04P136 152 176 1.0 136 5.0 1.8 219 0.108
BZW404-136 152 168 1.0 136 5.0 1.8 219 0.108
BZW04P145 161 187 1.0 145 5.0 1.7 234 0.108
BZW04-145 161 179 1.0 145 5.0 1.7 234 0.108
BZW04P154 171 198 1.0 154 5.0 1.6 246 0.108
BZW04-154 171 189 1.0 154 5.0 1.6 246 0.108
BZW04P171 190 220 1.0 171 5.0 1.5 274 0.108
BZW04-171 190 210 1.0 171 5.0 1.5 274 0.108
BZW04P188 209 242 1.0 188 5.0 1.4 301 0.108
BZW04-188 209 231 1.0 188 5.0 1.4 301 0.108
BZW04P213 237 275 1.0 213 5.0 1.5 344 0.110
BZW04-213 237 263 1.0 213 5.0 1.5 344 0.110
BZW04P239 266 308 1.0 239 5.0 1.5 384 0.110
BZW04-239 266 294 1.0 239 5.0 1.5 384 0.110
BZW04P256 285 330 1.0 256 5.0 1.2 414 0.110
BZW04-256 285 315 1.0 256 5.0 1.2 414 0.110
BZW04P273 304 352 1.0 273 5.0 1.2 438 0.110
BZW04-273 304 336 1.0 273 5.0 1.2 438 0.110
BZW04P299 332 385 1.0 299 5.0 0.90 482 0.110
BZW04-299 332 368 1.0 299 5.0 0.90 482 0.110
BZW04P342 380 440 1.0 342 5.0 0.90 548 0.110
BZW04-342 380 420 1.0 342 5.0 0.90 548 0.110
BZW04P376 418 484 1.0 376 5.0 0.80 603 0.110
BZW04-376 418 462 1.0 376 5.0 0.80 603 0.110
NOTES:
(1) V
(BR)
measured after ITapplied for 300µs IT=square wave pulse or equivalent
(2) Surge current waveform per Fig. 3 and derated per Fig. 2
(3) All terms and symbols are consistent with ANSI/IEEE C62.35
(4) For bi-directional devices with V
WM
of 10 Volts and less, the IDlimit is doubled
RATINGS AND CHARACTERISTIC CURVES BZW04P5V8 THRU BZW04-376
FIG. 1 - PEAK PULSE POWER RATING CURVE
P
PPM
, PEAK PULSE POWER, kW
td, PULSE WIDTH, sec.
TA, AMBIENT TEMPERATURE, °C
FIG. 4 - TYPICAL JUNCTION CAPACITANCE
UNIDIRECTIONAL
FIG. 3 - PULSE WAVEFORM
t, TIME, ms
V
(BR)
, BREAKDOWN VOLTAGE, VOLTS
TL,LEAD TEMPERATURE,°C
V
(BR),
BREAKDOWN VOLTAGE, VOLTS
NUMBER OF CYCLES AT 60 H
Z
P
PPM,
PEAK PULSE CURRENT, %
PEAK PULSE POWER (P
PP
) OR CURRENT (I
PP
)
DERATING IN PERCENTAGE, %
C
J
, JUNCTION CAPACITANCE, pF
I
FSM,
PEAK FORWARD SURGE CURRENT,
AMPERES
NON-REPETITIVE
PULSE WAVEFORM
SHOWN in FIG. 3
TA=25°C
TA=25°C
PULSE WIDTH (t
d
) is
DEFINED as the POINT
WHERE the PEAK
CURRENT DECAYS
to 50% of I
PP
tr=10µsec.
TJ=25°C
f=1.0 MHz
Vsig=50mVp-p
MEASURED at
ZERO BIAS
MEASURED at
STAND-OFF
VOLTAGE, V
WM
TA=25°C
MEASURED at
DEVICES
STAND-OFF
VOLTAGE, V
WM
1.6 x 1.6 x 0.040"
(40 x 40 x 1mm.)
COPPER HEAT SINKS
8.3ms SINGLE HALF SINE-WAVE
(JEDEC Method)
TJ=TJmax.
PEAK VALUE
I
PPM
HALF VALUE - I
PP
2
10/1000µsec. WAVEFORM
AS DEFINED BY R.E.A.
FIG. 6 - MAXIMUM NON-REPETITIVE FORWARD
SURGE CURRENT UNIDIRECTIONAL
FIG. 5 - STEADY STATE POWER DERATING CURVE
PM
(AV),
STEADY STATE POWER DISSIPATION, WATTS
I
D,
INSTANTANEOUS REVERSE LEAKAGE
CURRENT, MICROAMPERES
FIG. 2 - PULSE DERATING CURVE
FIG. 7-TYPICAL REVERSE LEAKAGE CHARACTERISTICS
60 H
Z
RESISTIVE OR INDUCTIVE LOAD
t
d
= 0.375”(9.5mm)
LEAD LENGTH
L
100
10
1.0
0.1
0.1
µ
s 1.0
µ
s10
150
100
50
0
0
1.0
µ
s 100
2.0
µ
s
3.0
1.0ms 10ms
4.0
100
75
50
25
0
0
100,000
10,000
25
50
75
100
125
175
150
200
1.00
0.75
0.50
0.25
0
0 25 50 75 100 125 150 175 200
100
10
1
1000
10
1.0
10
50
40
30
20
10
0
1
10
100 200
100
0.1
0.01
0
100
200
300
400
500
Loading...