General Electric PFIC1NFZBV User Manual

94" French Door Bottom Freezer Refer

A

Front View

Top View

G

D

C

F

B

E

H

PFIC1NFZ

Alternate
water
line location
through floor

1/2"

Recommended water line
location using recess
in rear wall

Recommended single loop
of 1/4" pex water line

Water hook-up
on the refrigerator

Rear Wall View

Top View

18"

24"

Allow 48" minimum water
line to enable refrigerator
to be pulled forward

Alternate
water
line location
through floor

1/2"

Top View

GE Profile™ Counter-Depth 20.7 Cu. Ft. Bottom-Freezer Drawer Refrigerator

Dimensions and Installation Information (in inches)

Height to top of hinge (in.) A 69-5/8

Height to top of case (in.) B 69

Case depth without door (in.) C 23-7/8

Case depth less door handle (in.) D 26-3/4*

Case depth with door handle (in.) E 31

Overall

Dimensions

Depth with fresh food door open 90° (in.) F 43-1/2

Width (in.) G 35-7/8

Width with door open 90° inc. door handle (in.) H 44

Air

Clearances

Note:

Anti-tip bracket part number 200D8494P001 will be shipped with
every counter-depth model
*Does NOT include a decorative panel

For answers to your Monogram,® GE Profile™ or

geappliances.com or call GE Answer Center®
service, 800.626.2000.

GE® appliance questions, visit our website at

Each side (in.)

Top (in.)

Back (in.)

1/8

1

1/2

Installation of water outlets

Above illustration intended for dimensional
reference only. Refer to photography for
actual product appearance.

IM POR TANT: Before finalizing specifications
for your GE Prof ile counter-depth refrigera tor,
please NOTE:

• A minimum width of 36" is required for

refrigerator installation

• Be sure to allow for 1/2" or 3/4" side panels
in addition to the 36" minimum

Specification Revised 8/10

Listed by
Underwriters
Laboratories

210820

PFIC1NFZ

2" Clearance
Handle Side

Appearance

Panel

Refrigerator
Door

1/4" Thick Backing

3/4

Panels thic ker than 1/4"

1/4" max.

3/4

5/16

Right Fresh Food Door

Freezer Door

16-29/32

5/16"
minimum at
1/4"
thickness

Top, right and
bottom

Top, right and
bottom

5/16"
minimum at
1/4"
thickness

2"
minimum at
1/4"
thickness

2"
minimum at
1/4"
thickness

Handle sideHandle side

26-3/32

2" minimum at
1/4" thickness

Handle side

Left, right and
bottom sides

5/16" minimum
at 1/4" thickness

35-29/32

38-15/16

Left Fresh Food Door

16-29/32

Raised portion
of panel

Raised portion
of panel

Raised
portion
of panel

38-15/16

1/8

1/8

1/8

1/8

1/8

1/4

1/4

1/4

1/4

1/4

1/8

1/4

Freezer Door

2-1/2

3/4

3/4

Filler

2-1/2

3/4

Panel

Right Fresh Food Door

Filler

2-1/2

3/4

3/4

Panel

Left Fresh Food Door

Filler

2-1/2

3/4

3/4

Panel

Right Fresh Food Door

Filler

2-1/2

3/4

3/4

Panel

Right Fresh Food Door

Filler

2-1/2

3/4

3/4

Panel

GE Profile™ Counter-Depth 20.7 Cu. Ft. Bottom-Freezer Drawer Refrigerator

Dimensions and Installation Information (in inches)

Order your own custom wood panels to match cabinetry or other decor.

Panels up to 1/4" thick or panels with 1/4" thick flanges will fit into your new

counter-depth refrigerator. Follow these patterns to ensure they will fit securely.
Add filler behind panels (see below) to ensure they will not rattle.
Weight Limits: Total weight of panels—Fresh Food = 10 lbs. each, Freezer = 18
lbs. max.

Note: Panels up to 3/4" will require special routing area around handles.

Dimensions may vary depending on depth of panel.

Panels less than 1/4" thick

For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
geappliances.com or call GE Answer Center®
service, 800.626.2000.

Dimensions for custom wood panels

Listed by
Underwriters
Laboratories

Specification Revised 8/10

210820

PFIC1NFZ

8' Ceiling

13" to 14"
Cabinet

12"
Soffit

36-1/8"

24-1/2"

70-1/4"*
21 cu. ft. models

25"
Counter
Top

ElectricalWater

3/4" Airspace
(1/2" Gap + 1/4"
Wall Plates)

24"
Cabinet

25"
Counter
Top

Electrical Water

3/4" Airspace
(1/2" Gap + 1/4"
Wall Plates)

24"
Cabinet

25"
Counter
Top

ElectricalWater

3/4" Airspace
(1/2" Gap + 1/4"
Wall Plates)

24"
Cabinet

25"
Counter
Top

Electrical Water

Trim

3/4" Airspace
(1/2" Gap + 1/4"
Wall Plates)

24"
Cabinet

FOR 21 CUBIC FOOT MODELS

FOR 24 CUBIC FOOT MODELS

GE Profile™ Counter-Depth 20.7 Cu. Ft. Bottom-Freezer Drawer Refrigerator

Dimensions and Installation Information (in inches)

Rough-in dimensions

Standard, new construction and replacement installation

Installation tips to maximize the built-in look

• All wall/floor molding should be removed prior

to installation.

• Water recess on rear wall recommended to prevent
water line damage. 48" minimum length, 1/4"-diameter

water line tubing recommended.

• When possible, recess both copper/pex water line and

electrical outlet (see local codes).

• Front and rear leveling legs are adjustable for the built-in

look (see owner’s manual).

• If optional collar trim kit is to be used or anticipated, see

collar trim installation on next page for different rough­in dimensions.

For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
geappliances.com or call GE Answer Center®
service, 800.626.2000.

*The rough-in dimensions of 70-1/4"/72-1/4" are minimum and measured from the finished floor to top of opening (or

the underside of the overhead cabinets). For models with trim kit: If frameless style cabinets are planned for above the

refrigerator, you may need to consider adding a maximum of 1/4" (70-1/2") to height of opening for 21 cu. ft. models to

allow additional clearance between cabinet doors and top of refrigerator trim when cabinet doors are in open position.

Specification Revised 8/10

Listed by
Underwriters
Laboratories

210820

PFIC1NFZ

1/2" to 3/4" Side Panel

GE Profile™ Counter-Depth 20.7 Cu. Ft. Bottom-Freezer Drawer Refrigerator

Dimensions and Installation Information (in inches)

Fabricating the enclosure

• The drawing shows an 84" cabinet elevation. Adjust dimensions accordingly for

other cabinet elevations.

• Cabinet pieces to order: (2) side panels and (1) wall cabinet.

• Side panels will typically be attached to adjacent cabinets and/or cleated to rear

wall and floor.

• Refer to GE refrigerator installation instructions for proper plumbing, and

electrical and air clearances.

• (1) Some framed cabinet lines will make a refrigerator enclosure with a cabinet
12" high x 39" wide with sides and 1-1/2" face frame extended down to floor to

create the refrigerator space. This will replace the above construction. (2) A tall
cabinet on either side of the refrigerator can replace a side panel.

• Counter overhangs on either side of the refrigerator should have clipped corners

to allow for full door swing.

• If the refrigerator has a wall returning beyond the front of the refrigerator on
either side, a 2" tall filler will help allow for movement of the door.

Door Panels

• See drawings for exact dimensions of the fresh-food and freezer door panels.

• Refrigerator door fronts from stock and most semi-custom cabinet
manufacturers will be supplied as 1/4"-thick panels cut to dimensions, with

closest available standard door sizes applied to front.
– This will leave a “reveal” at top/bottom and sides. Width of “reveal” will depend

on manufacturer’s standard door sizes.

– Door will be affixed on the 1/4" panels at factory or in the field by the local

supplier, depending on manufacturer.

• Local shop-built or custom cabinet supplier may fabricate custom 3/4" panels.
In this case, edges must be routed.

• Follow notes on drawing to assure room for fingers/hands to open handles.

Create a custom look for your GE Profile counter-depth bottom-freezer refrigerator

Still another advantage offered by GE Profile counter-depth refrigerators is ease
of installation. For a refrigerator that does so much to enhance the beauty of your
kitchen, the “behind-the-scenes” preparation and installation are surprisingly simple.

For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
geappliances.com or call GE Answer Center®
service, 800.626.2000.

Listed by
Underwriters
Laboratories

Specification Revised 8/10

210820

PFIC1NFZ

GE Profile™ Counter-Depth 20.7 Cu. Ft. Bottom-Freezer Drawer Refrigerator

Features and Benefits

• Counter-depth configuration - Counter-depth configuration makes it possible to have the look of a

built-in without the added expense

• ClimateKeeper™ system - Electronic controls, multiple electronic sensors and a multi-flow air system

help provide even cooling

• Factory-installed icemaker with water filtration system - Refrigerator comes ready to automatically

create filtered ice

• Upfront temperature controls with actual temperature display - Easy-to-reach, easy-to-read

controls display accurate temperatures

• Freshness Center™ with full-width drawer - Maintain fresh tastes with two humidity-controlled

crispers and a full-width drawer

• BrightSpace™ interior with GE Reveal® lighting - It’s easy to find tasty treats under bright, clear

interior lighting

• Multi-level Slide ‘n Store™ system - You’ll have instant access to frozen foods with a plastic bin and

wire baskets

• In-the-door condiment bin and beverage rack - Cans and condiments are chilled and ready without

taking up valuable shelf space

• QuickSpace™ shelf - Tall containers area snap with a quick slide of the retractable shelf

• TurboCool™ setting - Restores proper temperature to the refrigerator after frequent door openings

• Secure-close door system - Self-closing doors maintain food freshness and peace of mind

• Adjustable spillproof glass shelves - Raised edges keep small spills from becoming big messes

• Adjustable gallon door bins - Offers ideal space for storing gallon containers in the door

• NeverClean™ condenser - Encased coils take the dirty work out of maintaining your refrigerator

• Model PFIC1NFZWV - White on white

• Model PFIC1NFZBV - Black on black

Specification Revised 8/10

210820