General Electric PDT145SSLSS Installation
Installation Instructions
Built-In Dishwasher
If you have questions, call GE Appliances at 800.GE.CARES (800.432.2737) or visit our website
at: GEAppliances.com. In Canada, please call 800.561.3344 or visit www.geappliances.ca
BEFORE YOU BEGIN
Read these instructions completely and carefully.
WARNING
• Remove all power leading to the appliance from the
circuit breaker or fuse box before beginning installation.
Failure to do so can result in a risk of electrical shock.
•
To reduce the risk of electric shock, fire, or injury to persons,
the installer must ensure that the dishwasher is completely
enclosed at the time of installation.
• The improper connection of the equipment grounding
conductor can result in a risk of electric shock. Check
with a qualified electrician or service representative
if you are in doubt that the appliance is properly
grounded. If house wiring is not 2-wire with ground, a
ground must be by the installer. When house wiring
is aluminum, be sure to use UL-Listed anti-oxidant
compound and aluminum-to-copper connectors.
•
To reduce the risk of electric shock, fire, or injury to
persons, the installer should check to ensure that wires are
not pinched or damaged, the house wiring is attached to the
junction box bracket through a strain relief, and all electrical
connections made at the time of install (wire nuts) are
contained inside of
• Do not use an extension cord or adapter plug with this
appliance.
• Be sure to leave complete literature package, these Installation
Instructions and product samples and/or coupons with the
consumer.
NOTE: Product improvement is a continuing endeavor
at GE Appliances. Therefore, materials, appearance and
specifications are subject to change without notice.
the junction box cover.
FOR YOUR SAFETY
Read and observe all WARNINGS and CAUTIONS
shown throughout these instructions.
While performing installations described in this
booklet, gloves and safety glasses or goggles
should be worn.
IMPORTANT – Observe all governing codes and
ordinances.
• Note to Installer – Be sure to leave these instructions
for the consumer’s and local inspector’s use.
• Note to Consumer – Keep these instructions with
your Owner’s Manual for future reference.
• Skill Level – Installation of this dishwasher requires
basic mechanical, electrical and plumbing skills.
Proper installation is the responsibility of the
installer. Product failure due to improper installation
is not covered under the GE Appliances Warranty.
See Warranty information.
• Completion Time – 1 to 3 Hours. New installations
require more time than replacement installations.
IMPORTANT – The dishwasher MUST be installed to
allow for future removal from the enclosure if service is
required.
Care should be exercised when the appliance is installed
or removed, to reduce the likelihood of damage to the
power supply cord.
If you received a damaged dishwasher, you should
immediately contact your dealer or builder.
Optional Accessories – See the Owner’s Manual for
available custom panel kits.
Your dishwasher is a water heating appliance.
READ CAREFULLY
KEEP THESE INSTRUCTIONS
0120501699B
31-31590 03-18 GEA
Installation Preparation
PARTS SUPPLIED IN
INSTALLATION PACKAGE:
• Drain hose extension
• Hose Clamp
• 2 mounting brackets for wood countertop or side
cabinets (NOTE: Use the appropriate brackets, as
shown, for your model width.)
• Toekick Insulation (18” Models Only)
• 6 Phillips-Head screws to secure dishwasher to
underside of countertop or to side cabinets
Hose Clamp
• Literature, samples and/or coupons
MATERIALS YOU WILL NEED:
• UL-listed wire nuts (3)
• Thread Seal Tape
• 90° elbow (3/4” hose internal thread on one end,
opposite end sized to fit water supply)
Materials For New Installations Only:
• Air gap for drain hose, if required
• Waste tee for house plumbing, if applicable
• Electrical cable or Power Cord Kit WX09X70910 (5’ 4”
long) or WX09X70911 (7’ 9” long) depending on your
installation.
• Screw-type hose clamp(s)
• Strain relief for electrical connection
• Hand shut-off valve (recommended)
• Hot water line–3/8” minimum, copper tubing
(including ferrule, compression nut) or GE Appliances
Part # WX28X326, flexible braided hose.
Drain Hose
Extension
Wire Nuts (3)
Air Gap
Strain Relief
Mounting Brackets
(18” Models Only)
Mounting Brackets
(24” Models Only)
Thread Seal
Waste Tee
Hand
Shut-Off
Valve
Tap e
Electrical Cable
(or Power Cord,
if applicable)
Hot Water Line,
Ferrule and
Compression Nut
Toekick Insulation
(18” Models Only)
Phillips-Head
Screws
90° Elbow
Hose Clamp(s)
Literature
TOOLS YOU WILL NEED:
• Phillips-head screwdriver
• 1/4” and 5/16” nutdriver
• T25 torque driver
• 6” adjustable wrench
• Gloves
• Safety glasses
• Flashlight
• Bucket to catch water
when flushing the line
• Level
• Measuring tape
• Carpenter’s square
For New Installations Only:
• Tubing cutter
• Drill and appropriate bits
• Hole saw set
Phillips-Head
Screwdriver
Safety Glasses
1/4” and 5/16”
Flashlight
Tubing Cutter
Nutdriver
Bucket
Drill and Bits
2
T25 Torque
Driver
6” Adjustable
Wrench
Level
Gloves
Measuring Tape
Carpenter’s
Square
Hole Saw Set
Installation Preparation
PREPARE DISHWASHER ENCLOSURE
This wall area
MUST be
free of
A = Height
Underside of
countertop to
floor
Plumbing and electric service
18” Models Only 32-1/2” min.-34-3/4” max. 18”
24” Models Only 32-3/8” min.-34-3/4” max. 24”
pipes and wires
5”
5”
3”
4”
Floor MUST be even
with room floor
B = Width
MUST enter shaded area
AB
24”
6”
Cabinets
square
and
plumb
WARNING
To reduce the risk of electric shock, fire, or injury
to persons, the installer must ensure that the
dishwasher is completely enclosed at the time of
installation.
• The dishwasher must be installed so that drain hose is
no more than 12’ in length for proper drainage.
• The dishwasher must be fully enclosed on the top, sides
and back, and must not support any part of the enclosure.
CLEARANCES:
• When installed into a corner,
allow 2” min. clearance
between dishwasher and
adjacent cabinet, wall or other
appliances. Allow 23-1/8” min.
clearance from the front of the
dishwasher for door opening.
Countertop
Dishwasher
23-1/8"
Clearance for Door
Opening 2” Minimum
DRAIN REQUIREMENTS
• Follow local codes and ordinances.
• Do not exceed 12’ distance to drain.
• Drain connection height is not to exceed 72” above
bottom of dishwasher.
NOTE : Air gap must be used if waste tee or disposer
connection is less than 18” above floor to prevent
siphoning.
DETERMINE DRAIN METHOD
The type of drain installation depends on the following
questions.
• Do local codes or ordinances require an air gap?
• Is waste tee less than 18” above floor?
If the answer to either question is YES, Method 1
MUST be used.
•
If the answers are NO, either method may be used.
CABINET PREPARATION
• Drill a 1-1/2” diameter hole in the cabinet wall within
the shaded areas shown in PREPARE DISHWASHER
ENCLOSURE for the drain hose connection. The hole
should be smooth with no sharp edges.
Method 1 – Air Gap with Waste Tee or Disposer
An air gap must be used when required by local codes
and ordinances. The air gap must be installed according to
manufacturer’s instructions.
Method 2 – “High Drain Loop” with Waste Tee or Disposer
Drain Hose Hanger
32"
Min.
18"
Min.
Drain Hose Hanger
32"
Min.
18"
Min.
IMPORTANT – When connecting
drain line to disposer, check to be sure
that drain plug has been removed.
DISHWASHER WILL NOT DRAIN IF
PLUG IS LEFT IN PLACE.
Remove
Drain
Plug
Tip: Avoid unnecessary service call charges.
Always be sure disposer drain plug has been removed
before attaching dishwasher drain hose to the disposer.
3
Installation Preparation
PREPARE ELECTRICAL WIRING
WARNING
Remove all power leading to the appliance from the
circuit breaker or fuse box before beginning installation.
Failure to do so can result in a risk of electrical shock.
1-1/2” Dia.
Hole (Max.)
Electrical Requirements
• This appliance must be supplied with 120V, 60 Hz.,
and connected to an individual properly grounded
branch circuit, protected by a 15- or 20-ampere circuit
breaker or time-delay fuse.
• Wiring must be 2 wire with ground and rated for 167°F
(75°C).
• If the electrical supply does not meet the above
requirements, call a licensed electrician before
proceeding.
Grounding Instructions–Permanent Connection
This appliance must be connected to a grounded metal,
permanent wiring system, or an equipment-grounding
conductor must be run with the circuit conductors and
be connected to the equipment-grounding terminal or
lead on the appliance.
Grounding Instructions–Power Cord Models
This appliance must be grounded. In the event of a
malfunction or breakdown, grounding will reduce the risk
of electric shock by providing a path of least resistance
for electric current. This appliance is equipped with a
cord having an equipment-grounding conductor and
a grounding plug. The plug must be plugged into an
appropriate outlet that is installed and grounded in
accordance with all local codes and ordinances.
3”
from
Cabinet
24”
from Wall
Ground
Black
White
Cabinet Preparation & Wire Routing
•
The wiring may enter the opening from either side, rear
or the floor within the shaded area illustrated above
in figure and as defined in PREPARE DISHWASHER
ENCLOSURE section.
• Cut a 1-1/2" maximum diameter hole to admit the
electrical cable. Edges of hole should be smooth and
rounded. Permanent wiring connections may pass
through the same hole as the drain hose and hot water
line, if convenient. If cabinet wall is metal, the hole
edge must be covered with a bushing.
NOTE:
separate hole in the cabinet.
Power cords with plug must pass through a
Metal Cabinet
Wall
Cord Protector
(Obtain locally
as needed)
Hole Diameter
1-1/2” Maximum
WARNING
The improper connection of the equipment grounding
conductor can result in a risk of electric shock. Check with
a
qualified electrician or service representative if you are in
doubt that the appliance is properly grounded. Do not modify
the plug provided with the appliance; if it will not fit the outlet,
have a proper outlet installed by a qualified technician.
Electrical Connection to Dishwasher
Electrical connection is on the right front of dishwasher.
• For permanent connections the cable must be routed
as shown in figure. Cable must extend a minimum of
24" from the rear wall.
• For power cord connections, install a 3-prong grounding
type receptacle in the sink cabinet rear wall, 6" min. or
18" maximum from the opening, 6" to 18" above the floor.
• Use only WX09X70910 (5’ 4” long) or WX09X70911
(7’ 9” long) Dishwasher Power Cord Kit. Do not use an
extension cord or adapter plug with this appliance.
4
Installation Preparation
PREPARE HOT WATER LINE
NOTE: GE Appliances recommends copper tubing for
the water line, but if you choose to use flexible hose,
use GE Appliances WX28X326, flexible braided hose.
• The water supply line (3/8” copper tubing or flexible
braided hose) may enter from either side, rear or
floor within the shaded area shown in the figure.
• The water supply line may pass through the same
hole as the electrical cable and drain hose. Or, cut an
additional 1-1/2" diameter hole to accommodate the
water line. If power cord with plug is used, water line
must not pass through power cord hole.
1-1/2”
Hot
Cabinet
Shut-off
Valve
5"
From
Dia.
Hole
15" From Wall
3"
6"
WATER LINE CONNECTION
• If using a flexible braided supply hose, label the
hose with the installation date to use as reference.
Flexible braided hoses, elbows and gaskets should
be replaced in 5 years.
• Turn off the water supply.
• Install a hand shut-off valve in an accessible location,
such as under the sink. (Optional, but strongly
recommended and may be required by local codes.)
• Water connection is on the left side of the dishwasher.
Install the hot water inlet line, using no less than 3/8”
copper tubing or a flexible braided hose. Route the
line as shown in PREPARE HOT WATER LINE and
extend forward at least 19” from rear wall.
• Adjust water heater for 120°F to 140°F temperature.
• Flush water line to clean out debris.
• The hot water supply line pressure must be 20-120 PSI.
PREPARATION
Locate the items in the installation packages:
• Screws
• Drain hose extension
• Mounting brackets
• Literature, product samples and/or coupons
Cabinet Face
3" From Floor
Turn page to begin dishwasher installation.
5
Dishwasher Installation
STEP 1
CHECK DOOR BALANCE
CAUTION
Opening the door will cause the
dishwasher to tip forward when it
is not fully installed. When opening
the door prior to the dishwasher
being fully installed, hold the top of
the dishwasher securely with one hand and hold the
door with the other hand. Gloves should be worn.
To check the door balance, hold the top of the dishwasher
firmly.
• Check the door balance by opening and closing the
door.
• If the door drops
when released,
increase the
spring tension.
If the door rises
when released,
decrease the
spring tension.
18” Models
Only
Increase
Decrease
24” Models
Only
Increase
Decrease
STEP 3
REMOVE TOEKICK
• Remove the 4 toekick screws
and the 2-piece toekick. Set
aside for use in Step 19.
STEP 4
INSTALL POWER CORD
Skip this step if the dishwasher will be permanently
connected to the house electrical system or has a
factory-installed power cord.
• The power cord and connections must comply with
the National Electrical Code, Section 422 and/or local
codes and ordinances. Maximum power cord length is
6 feet. Power Cord Kit WX09X70910 or WX09X70911,
available for purchase from an authorized
GE Appliances dealer, meets these requirements.
UL Listed Wire Nuts
Black White
Junction Box
Cover
Dishwasher
Ground Wire
and Screw
Dishwasher
Wires
Dishwasher Ground
Wire and Screw
Junction Box Bracket
Ground/
Green
Strain
Relief on
Power
Cord
STEP 2
ADJUST LEVELING LEGS
• Move the dishwasher close to the installation location
and lay it on its back. NOTE: Do not place the
dishwasher on its side.
• Measure installation height and dishwasher height.
Extend leveling legs out from the dishwasher base,
1/2” less than installation height.
Adjust to
Installation
Height
Leveling leg
shown with the
dishwasher laying
on its back
• Remove junction box cover.
• Install strain relief in the junction box bracket.
• Insert the power cord through the strain relief and tighten.
• Make sure black, white and green dishwasher wires are
threaded through the hole in the junction box bracket.
• Connect power cord white (or ribbed) to dishwasher
white, black (or smooth) to dishwasher black and
ground to dishwasher green wire. Use UL-listed wire
nuts of appropriate size.
• Replace junction box cover using the screw. Be sure
wires are not pinched under the cover.
6
Dishwasher Installation
STEP 5
• Ensure rubber gasket is located between valve and
elbow.
• Thread 90° elbow onto the water valve.
• Do not overtighten elbow. Water valve bracket could
bend or water valve fitting could break.
• Position the end of the elbow to face the rear of the
dishwasher.
STEP 6
INSTALL 90° ELBOW
Water
Valve
Gasket
POSITION WATER LINE
90°
Elbow
Screw the
90° elbow
onto the
water valve
until it is
secure and
points to the
rear of the
dishwasher
AND HOUSE WIRING
• Position water supply line and house wiring on the
floor of the opening to avoid interference with base
of dishwasher and components under dishwasher.
3"
6"
Water
Line
House
Wiring
3"
6"
STEP 7
INSTALL DRAIN HOSE,
THROUGH CABINET
• Stand the dishwasher upright and position it in front
of cabinet opening. Insert drain hose into the hole in
cabinet side. If a power cord is used, guide the end
through a separate cabinet opening.
Maximum
Drain Hose
Length 12’
Insulation
Blanket
Tip: Prevent unnecessary service call charges for
fill, drain or noise concerns.
Position utility lines so they do not interfere with
anything under or behind the dishwasher.
STEP 8
The molded end of the drain hose will fit 5/8” through 1”
diameter inlet ports on the air gap, waste tee or disposer.
• Determine size of inlet port.
• Cut drain hose
connector on the
marked line, if
required, to fit the
inlet port.
• Use the drain hose
extension provided
and connect directly
to the drain loop
already attached to the unit. Secure the connection,
with hose clamp, to the provided user bag drain
hose.
Hose Clamp
CONNECT DRAIN LINE
Water
Line
Drain
Hose
House
Wiring
Power Cord
(If Used)
Cutting Lines
3/4"
1"
IMPORTANT: Do NOT cut
corrugated portion of hose
5/8"
• DRAIN CONNECTION HEIGHT IS NOT TO EXCEED
72” ABOVE BOTTOM OF DISHWASHER.
• TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED
12 FEET FOR PROPER DRAIN OPERATION.
7
Dishwasher Installation
STEP 8
CONNECT DRAIN LINE
(CONT.)
• Connect drain line to air gap, waste tee or disposer
using the previously determined method. Secure
hose with a screw-type clamp.
Method 1 – Air gap with waste tee or disposer
Waste Tee Installation
Method 2 – “High drain loop” with waste tee or
disposer
Fasten drain hose to underside of countertop with a
hanger.
Drain Hose Hanger
Disposer Installation
Drain Hose Hanger
STEP 9
INSTALL MOUNTING
BRACKETS
You will need the mounting brackets and 4 of the
Phillips-Head screws set aside in the PREPARATION
section.
You must install the mounting brackets onto the
dishwasher tub frame top OR sides prior to sliding
the dishwasher into place under the countertop.
The mounting brackets have several available
attachment positions to accommodate different
cabinet constructions.
TOP MOUNTING OPTION
Install mounting brackets on top if the underside
of countertop is wood or wood-like material that
accepts screws:
IMPORTANT - After installing brackets and before
closing dishwasher door, adjust the brackets by bending
them up as needed, so that they do not contact the top
of dishwasher door and cause damage.
Top Mounting for 18” Models Only
Phillips
Screws
Bracket
Phillips
Screws
Bracket
Min.
18"
Min.
Waste Tee Installation
32"
Disposer Installation
18"
Min.
32"
Min.
IMPORTANT – Either one of the above methods
must be used or dishwasher will not operate
properly.
IMPORTANT – When
connecting drain line to
disposer, check to be sure that
drain plug has been removed.
DISHWASHER WILL NOT
Remove
Drain
Plug
DRAIN IF PLUG IS LEFT IN
PLACE.
Tip: Avoid unnecessary service call charges for a
no drain complaint.
Make sure excess drain hose has been pulled through
the cabinet opening. This will prevent excess hose
in the dishwasher cavity from becoming kinked or
crushed by the dishwasher.
Bend and break at cutout slots in brackets (if/as necessary)
on both sides after installing if counter has a short overhang.
Top Mounting for 24” Models Only
Phillips
Screws
Phillips
Screws
Bend and break at cutout slots in brackets (if/as necessary)
on both sides after installing if counter has a short overhang.
Bracket
Bracket
• If you are installing the dishwasher under a counter
with a short overhang, the countertop brackets may
extend beyond the edge of the counter. If this is the
case, remove the excess length by repeatedly bending
the brackets at the front notch only until they break.
8
Dishwasher Installation
STEP 9
INSTALL MOUNTING
BRACKETS (CONT.)
SIDE MOUNTING OPTION
Install mounting brackets on sides if the countertop
is granite or similar material that will not accept
wood screws:
• Break off front portion of the tab with pliers at the
location shown, prior to attaching to dishwasher.
• Position the left-hand side bracket as shown. Repeat
with the right bracket.
Side Mounting for 18” Models Only
Phillips
Screws
STEP 10
SLIDE DISHWASHER
PARTIALLY INTO CABINET
IMPORTANT – Do not push against front panel with
knees. Damage will occur.
• Grasp the sides of the front panel and slide
dishwasher into the opening a few inches at a time.
Do not push
against front
door panel
with knee.
Damage to
the door panel
will occur.
• As you proceed, pull the drain hose through the
opening under the sink. Stop pushing when the
dishwasher extends about 6 inches forward of
adjacent cabinets.
Make sure drain hose is not kinked under or behind
•
the dishwasher.
• Make certain the house wiring, drain line and
water line do not interfere with components under
dishwasher.
Bend and break at cutout slots in brackets
(if/as necessary) on both sides before installing.
Side Mounting for 24” Models Only
Phillips
Screws
Bracket
Bend and break at cutout slots in brackets
(if/as necessary) on both sides before installing.
Bracket
STEP 11
POSITION DISHWASHER
UNDER COUNTERTOP
• Push the dishwasher into the cabinet.
• Push the sides with your hands. Do not use your
knee against the door since door damage will occur.
Do not push
against front
door panel
with knee.
Damage to
the door panel
will occur.
• Check that the tub insulation blanket does not get
“bunched-up” or interfere with the springs as you
slide it into the cabinet.
• Center the dishwasher in the opening.
• Front of door panel should be flush with face of
cabinet.
• Carefully open and close the door to ensure that the
door panel does not catch or rub on the cabinet frame.
• If the door catches or rubs on the frame, reposition
and/or level the unit (see Step 14) until the door
moves freely and does not contact the cabinet frame.
9
Dishwasher Installation
STEP 11
POSITION DISHWASHER
UNDER COUNTERTOP
(CONT.)
Door
Fits and
Swings
Back
Behind
Cabinet
Frame
Correct
Alignment
The controls on these
models are designed
to be hidden by your
countertop. Align the
dishwasher as shown in
figure.
Leave a 1/2” minimum gap
between the underside of the
countertop and the top of the
dishwasher door as shown in
figure.
NOTE: If the drain hose
gets trapped behind the unit
it can prevent the controls
from being hidden by the
countertop.
Tip: The leveling legs can
be used to increase or
decrease the amount of gap
between the controls and
the countertop affecting the
visibility of the controls.
IMPORTANT– Leave a 1/2”
minimum gap between the
controls and the underside
of the countertop to prevent
condensation and damage
to the control panel from
screwheads.
NOTE: If this dishwasher is replacing an existing
dishwasher, the old countertop bracket screw holes
may not be in the correct position to accept a topcontrol model. New holes may be required.
Door Catches
on Cabinet Frame
Incorrect
Alignment
TOP VIEW
Hold 3 Sec To Cancel
Clean
Sanitized
Start
Controls Hidden by Countertop
Countertop
1/2”
Min.
Front
View
Dishwasher
Door
Countertop
Control
Panel
STEP 12
CONNECT WATER
SUPPLY
Connect water supply line to 90° elbow.
If using a flexible braided hose connection:
• Attach nut to 90° elbow using an adjustable wrench.
If using a copper
tubing connection:
• Slide compression nut,
then ferrule over end
of water line.
• Insert water line into
90° elbow.
• Slide ferrule against
elbow and secure with compression nut.
STEP 13
CONNECT POWER SUPPLY
If a power cord with plug is already installed
proceed to Step 14.
WARNING
If house wiring is not 2-wire with ground, a ground
must be provided by the installer. When house wiring
is aluminum, be sure to use UL-Listed anti-oxidant
compound and aluminum-to-copper connectors.
• Remove junction box cover.
• Secure house wiring to the back of the junction box
with a strain relief.
• Locate the 3 dishwasher wires, (white, black and
green) with the stripped ends coming out of the AC
jumper. Use UL listed wire nuts of appropriate size to
connect incoming ground to green, white to white and
black to black.
• Replace the junction box cover using the screw.
Check to be sure that wires are not pinched under
the cover.
• If using a Power Cord Kit, use GE Appliances part
number WX09X70910 or WX09X70911 and refer to
the included instructions.
NOTE: Do not remove the Junction Box Bracket.
UL Listed Wire Nuts
Black White
Junction Box
Cover
Dishwasher
Ground Wire
and Screw
Dishwasher
Wires
Dishwasher Ground
Wire and Screw
Junction Box Bracket
NOTE: All ground screws, brackets and wires must
remain intact.
10
90° Elbow
Ferrule Compression
Hot Water
Supply Line
Nut
Ground/
Green
House
Wiring
with
Strain
Relief
Dishwasher Installation
C
STEP 14
IMPORTANT – Dishwasher must be level for proper dish
rack operation, wash performance and door operation. The
dishwasher must be leveled left to right and front to back.
• Make sure 1/2” minimum gap under the countertop is
maintained.
• Remove the lower dish rack and place a level on the
door and lower rack track as shown in the figure.
Use Level to Check
Front-to-Back
• If the dishwasher is not
level, adjust the four
leveling legs individually.
Tip: Prevent unnecessary
service charges. Verify
dishwasher is leveled.
Pull the dish racks half way
out. They should stay put.
Open and close the door.
The door should fit in the
tub opening without hitting
the side of the tub. If the
racks roll on their own, or the door hits the side of tub,
re-level the dishwasher.
IMPORTANT – After leveling, verify that the dishwasher
is still in the correct position shown in Step 11.
LEVEL DISHWASHER
Use Level to Check
Side-to-Side
Turn Legs
to Adjust
STEP 15
SECURE DISHWASHER
TO COUNTERTOP OR
CABINET (CONT.)
IMPORTANT – Prevent door panel and control
panel damage. Dishwasher must be positioned so
the front panel and control panel do not contact the
adjacent cabinets or countertop. Mounting screws
must be driven straight and flush. Protruding screw
heads could scratch the door panel or control panel
and interfere with door operation.
Method 1
Secure dishwasher to underside of wood countertop.
• Fasten the dishwasher to the underside of the
countertop with the 2 Phillips head screws. Refer to
figure. Make certain screws are driven straight and
flush to prevent panel damage.
Wood Countertop
Screws into Upper Brackets
Method 2
Secure dishwasher to cabinet sides.
• Remove plug buttons from tub. Do not discard.
• Fasten the dishwasher to the adjacent cabinets with
the 2 Phillips-Head screws provided. Refer to the
figure. Make certain screws are driven straight and
flush to prevent panel damage. Do not screw into
the cabinet face frame.
• Re-install plug buttons.
Solid Surface Countertop
Plug Buttons
STEP 15
SECURE DISHWASHER
TO COUNTERTOP OR
CABINET
In this step you will need
the 2 remaining Phillips
Head screws from the
screws set aside in the
PREPARATION section.
The dishwasher must be
secured to the countertop
or the cabinet sides.
When the underside of the
countertop is wood, use Method 1 (Countertop Mounting).
Use Method 2
the countertop is made of a material, such as granite,
that will not accept wood screws.
(Side Mounting)
Countertop Mounting
(18” Model Bracket Shown)
Side Mounting
(24” Model Bracket
Shown)
when the underside of
Screws into Side Brackets
• Re-check that the dishwasher is square and level at
both the top and bottom of the cabinet opening, with no
twisting or distortion of the tub or door after mounting to
the cabinets/countertop. Adjust if necessary.
• Confirm all leveling legs are in contact with the floor
to prevent the dishwasher from rocking and ensure
proper door and latch operation.
Both Methods
ountertop
1/2"
Dishwasher Door
Min.
• When step is complete, close dishwasher door
and verify that gap between countertop and top of
dishwasher door is at least 1/2”.
11
Loading...