MODELS :
AR 30FUAN / AO 30FNBWL
AR 30UUAN / AO 30UNBWL
ART30UUAN / AOT30UNBWL
FEATURES
Installation styles
Embedded in Ceiling
Hanging from Ceiling
DUCT TYPE
AR30W
Low static pressure mode function
1.Low static pressure mode 1 air volume at 70Pa (fan speed:high)
2.Normal Mode Air volume at 100Pa (fan speed:high)
When installed, normal middle static pressure mode, and low static
pressure mode can be selected by switching over using DIP switch
on the board in the control box. Therefore, these models can be operated under the wide range of conditions.
(230V)
/h)
3
Air volume (m
070100
Static pressure (Pa)
12
DUCT TYPE
AR30W
Slim & compact design
In the case of bottom suction type, as seen from lower rear part.
Control Box that has been convex shape
is now united with main unit (DIP Switch is
located on the internal substrate.)
One-touch operating and easy-to-install
long-life filter (optional)
In addition to the slim height of 270 mm which is our sales point, further compactification is attained by reducing 65 mm from the width with the flanking
control box embedded inside the chassis.
- (04 - 01) -
Page 3
EASY MAINTENANCE
In the case of rear suction type, as seen from lower rear part.
Conventional model
1
3
4
New model
4
1
1.Control box
2.Fan casing
3.Fan
4.Motor
2
2
3
Bottom panel: 2 units
Large bottom panel: 1 unit
Structural improvement is attained by making the bottom panel two pieces, front and
rear, and the internal fan casing is also made dismountable in two pieces namely,
upper and lower ones.
DUCT TYPE
AR30W
The motor and fan maintenance and dismounting can be made easily by removing
the rear panel and lower part of the casing with the main chassis installed.
DUCT TYPE
AR30W
- (04 - 02) -
Page 4
4-2. REMOTE CONTROLLER
4-2-1. WIRED REMOTE CONTROLLER
FEATURES
Various timer setup (ON / OFF / WEEKLY) are possible.
Equipped with weekly timer as standard function.
(2 times Start / Stop per day for a week)
SUMOTUWETH FR SA
7
3126 9
15 18 21
When setting up a timer, operation mode and a temperature
setup can be changed.
When a failure occurs,the error code is displayed. (Maximum of 16)
Error indication.(A maximum of 16 error histories are memorizable.)
Up to 16 indoor units can be simultaneously controlled.
Anti freeze and energy saving operation are possible.
Easy installation with a slim shape with no boldge in the back.
The room temperature can be controlled by being detected the temperature
accurately with built-in thermo sensor.
High performance and compact size
Three functions are combined in
one unit.
DUCT TYPE
AR30W
Wired
remote
controller
Weekly
timer
Setback
timer
DUCT TYPE
AR30W
Built-in timers
Setback timerWeekly timer
Possible to set ON/OFF time to operate twice each day
of the week.
SUMOTUWETH FR SA
7
3126 9
15 18 21
Setup screen example
(Set to Wednesday: 8:00 to 20:00.)
0 3 6 9 12 15 18 21 Time
Easy-to-understand time bar display
24°C
SUMOTUWETH FR SA
7
3126 9
15 1821
Screen
after setup
At "Weekly timer" + "Set back timer" setup
24°C 28°C 24°C
0 3 6 9 12 15 18 21 Time
Timer
area
Operation
area
Possible to set temperature for two time spans and
for each day of the week.
SUMOTUWETH FR SA
3126 9
15 18 21
Setup screen example
(Set from Sunday to Saturday: 12:00 to 15:00, 28 °C.)
28°C
0 3 6 9 12 15 18 21 Time
24°C
28°C
Simple installationEasy-to-understand operation
Components are compatible with standard
switch boxes. Flat back construction allows
equipment to be installed wherever it is
needed.
[
Variable timer control
]
The operation/display sections are zoned according to time and operation, enabling variable programming to match application.
- (04 - 03) -
European
switch box
JIS box
Page 5
FUNCTIONS
1
START/STOP button
Pressed to start and stop operation.
Display
2
7
8
9
10
SUMOTUWETH FR
369
CLOCK ADJUST
SET BACK
DELETESET
12 15 18 21
DAY
DAY OFF
SA
13
1
3
ENERGY
SAVE
THERMO
SENSOR
4
6
2
Set temperature button
Selects the setting temperature.
3
Master control button
Selects the operating mode(AUTO, HEAT, FAN, COOL, DRY).
4
Fan control button
Selects the fan speed (AUTO, LOW, MED, HIGH).
5
Energy save button
Turns the energy efficient mode on and off.
11
12
5
6
Thermo sensor
7
Timer mode (CLOCK ADJUST) button
Selects the timer mode (OFF TIMER, ON TIMER, WEEKLY TIMER)
Set the current time.
8
Day (DAY OFF) button
Display panel
DUCT TYPE
AR30W
14
15
1617 18
Temporarily cancels of one day timer.
9
Set back button
pressed select the set back timer.
10
Set time button
DUCT TYPE
AR30W
Pessed to select the set back timer.
SUMOTUWETH FR
SA
11
Delete button
The schedule of a weekly timer is deleted.
369
12 15 18 21
1920
12
Set button
Sets the date, hour, minute and on-off time.
13
Operation lamp
Lights during operation and when the timer is on.
DIMENSION
[ Unit : mm ]
17
120
SUMOTUWETH FR
369
12 15 18 21
DAY
CLOCK ADJUST
DAY OFF
SET BACK
DELETESET
Front View
120
SA
ENERGY
SAVE
THERMO
SENSOR
SPECIFICATION
SIZE (H x W x D mm)120 x 120 x 17
WEIGHT( g )160
CABLE LENGTH ( m )
POWER( V )
10
12
14
Timer and clock display
15
Operation mode display
16
Fan speed display
17
Central control display
18
Temperature display
19
Stand by display
Indicates during the oil recovery and defrosting operation.
20
Energy save display
- (04 - 04) -
Page 6
4-3. SPECIFICATIONS
AR 30FUANAR 30UUANART30UUAN
AO 30FNBWLAO 30UNBWLAOT30UNBWL
240V 50Hz
Rows x Stages
Fin Pitch
Rows x Stages
Fin Pitch
Sirocco x 2
70
Copper tube
2 x 38
1.3
Propeller x 1
67
Outer diameter 38 mm / Inner diameter 36 mm
Steel
Galvanlzed steel sheet
270 x 1135 x 700
3.0(6.3)
9.52 ( 3 / 8 inc.)
ROTARY
Permanent Starting Condenser
Alminum fin
830 x 900 x 330
294 x 1000 x 39.9
Alminum fin
798 x 900 x 36.38
15.88 ( 5 / 8 inc.)
43 / 50 ( 95 / 110 )
69 /75 ( 152 / 165 )
FLARE
DUCTED MODELS
HEAT PUMP TYPE
198-264V 50Hz
2300
30(chargeless:7.5)
R410A
15
970 x 1050 x 445
300 x 1300 x 790
Beige (10YR7.5/1.0NN)
POE
0 to 43
-7 to 24
WIRED (3TA)
2200
Copper tube
3 x 14
1.4
1250
1185
1110
-
780
400
30 to 150
TYPE
MODEL NAME
INDOOR
OUTDOOR
POWER SOURCE
AVAILABLE VOLTAGE RANGE
CAPACITY
COOLING
RATED
HEATING
RATED
INPUT POWER
kW
CURRENT
A
STARTING CURRENT
kW/kW
MOISTURE REMOVAL
AIR
CIRCULATION
INDOOR
m3/h
OUTDOOR
FAN SPEED
INDOOR
r.p.m
OUTDOOR
RECOMMENDED STATIC PRESSURE
FAN TYPE x Q'ty
FAN MOTOR OUTPUT
W
NOISE LEVEL
(SOUND
PRESSURE)
COOL/HEAT
INDOOR
dB(A)
OUTDOOR
COMPRESSOR
TYPE
STARTING METHOD
HEAT
EXCHANGER
TYPE
INDOOR
Coil
Fin
OUTDOOR
Coil
Fin
CASING COLOR
DIMENSIONS
H × W × D
NET
mm
GROSS
DRAIN PIPE
MATERIAL
SIZE
REFRIGERANT
TYPE
REFRIGERANT OIL
TYPE
OPERATION(OUTDOOR)
°C
REMOTE CONTROLLER TYPE
kg(lbs)
PIPE
CONNECTION METHOD
SIZE
mm
MAX LENGTH
MAX HEIGHT
WEIGHT
NET /
GROSS
-
230V 50Hz
1400
1300
1200-3300
70
COOLING TYPE
EUROPEAN ENERGY LABELCOOLINGCC-
COOLINGRAT ED2.992.993.15
HEATINGRATED-2.632.80
COOLINGRAT ED14.014.014.3
HEATINGRATED-12.413.1
EER COOLING2.812.812.70
COP HEATING-3.613.39
High1430
Med1350
Low1260
Quiet-
High3400
Low-
High1260
Med1210
Low1150
DUCT TYPE
AR30W
Quiet-
High800
Low420
INDOOR
OUTDOOR
INDOOR
OUTDOOR
High40/-40/4040/40
Med38/-38/3838/38
Low36/-36/3636/36
kW8.408.408.50
BTU/h287002870029000
kW-9.509.50
BTU/h-3240032400
A
l/h (pints/h)
Pa
53/-53/5453/54
40
DUCT TYPE
AR30W
OUTPUTW
mm
Coil Dimensionsmm
mm
Coil Dimensionsmm
INDOOR
INDOOR
OUTDOOR
INDOOR
OUTDOOR
INDOOR
OUTDOOR68 / 74 ( 150 /163 )
OUTDOOR
LIQUID
GAS
m
m
CHARGEkg
COOLING
HEATING-
Note:Specifications are based on the following conditions.
Cooling:Indoor tem perature of 27 °CDB / 19 °CWB,and outdoor temperature of 35 °CDB/24 °CWB.
Heating:Indoor temperature of 20 °CDB / 15 °CWB,and outdoor temperature of 7 °CDB/6 °CW B.
Static pressure of measurement : 100Pa
Pipe length : 7.5 m, Height difference : 0 m.(Outdoor unit - Indoor unit)
mm
- (04 - 05) -
Page 7
4-4. DIMENSIONS
4-4-1. OUTDOOR UNIT
MODELS : AO 30F, AO 30U, AOT30U
(Unit : mm)
Top view
900
830
21
DUCT TYPE
AR30W
9
Front view
77
31330
400
12
DUCT TYPE
AR30W
Side view
650
Air flow
370
MOUNTING POSITION
When there are obstacles at the
back or front sides.
m
e
r
00 m
1
or mo
m
m
e
600
mor
or
603
Bottom view
When there are obstacles at the
back, side(s), and top.
600 mm or more
100 mm
o
r mo
re
2
5
0 mm
(
Se
r
v
o
i
c
r
mo
e
s
pa
r
e
c
e)
30
or mor
m
m
0
196
99
147
170
When there are obstacles at the
back, side with the installation of
more than one unit.
250
or
m
m
m
or
e
e
or
250
m
m
m
or
e
e
mm
or
00
m
3
or
- (04 - 06) -
Page 8
4-4-2. INDOOR UNIT
MODELS : AR 30F, AR 30U, ART30U
Front view
(Unit : mm)
DUCT TYPE
DUCT TYPE
AR30W
AR30W
Side view (L)
Side view (R)
Top view
Rear view
- (04 - 07) -
Page 9
MOUNTING POSITION
150 mm
or more
150 mm
or more
MAINTENANCE HOLE
It shall be possible to install and remove
the control box.
300mm
DUCT TYPE
AR30W
500mm
500mm
100mm
It shall be possible to install and remove
the control box, fan units and filter.
AFR: Air flow rate (m3/min)
TC : Total capacity (kW)
PI : Power Input (kW)
TCPITCPITCPITCPITCPITCPITCPI
AR30W
- (04 - 14) -
Page 16
4-8. CAPACITY COMPENSATION FOR PIPE LENGTH
57.51015202530
15---0.9520.9190.8880.857
10--0.9850.9520.9190.8880.857
7.5-1.0000.9850.9520.9190.8880.857
51.0101.0000.9850.9520.9190.8880.857
01.0101.0000.9850.9520.9190.8880.857
-51.0020.9920.9770.9440.9120.8810.850
-7.5-0.9880.9730.9410.9080.8770.847
-10--0.9690.9370.9040.8740.843
-15---0.9290.8970.8670.836
PIPE LENGTH (m)
COOLING
HEIGHT DIFFERENCE (m)
Outdoor unit
is up-side
Outdoor unit is
bottom-side
AND HEIGHT DIFFERENCE
MODELS :
AR 30F / AO 30F
COEFFICIENT OF COMPENSATION FOR HEIGHT DIFFERENCE
DUCT TYPE
DUCT TYPE
AR30W
AR30W
- (04 - 15) -
Page 17
MODELS : AR 30U / AO 30U, ART30U / AOT30U
PIPE LENGTH (m)
Outdoor unit is
bottom-side
Outdoor unit
is up-side
COOLING
HEIGHT DIFFERENCE (m)
HEIGHT DIFFERENCE (m)
PIPE LENGTH (m)
HEATING
Outdoor unit
is up-side
Outdoor unit is
bottom-side
COEFFICIENT OF COMPENSATION FOR HEIGHT DIFFERENCE
57.51015202530
15---0.9520.9190.8880.857
10--0.9850.9520.9190.8880.857
7.5-1.0000.9850.9520.9190.8880.857
51.0101.0000.9850.9520.9190.8880.857
01.0101.0000.9850.9520.9190.8880.857
-51.0020.9920.9770.9440.9120.8810.850
-7.5-0.9880.9730.9410.9080.8770.847
-10--0.9690.9370.9040.8740.843
-15---0.9290.8970.8670.836
DUCT TYPE
AR30W
57.51015202530
DUCT TYPE
AR30W
15---0.9560.9390.9220.904
10--0.9790.9610.9430.9270.909
7.5-0.9930.9820.9640.9460.9290.911
51.0050.9950.9840.9660.9480.9310.913
01.0101.0000.9890.9710.9530.9360.918
-51.0101.0000.9890.9710.9530.9360.918
-7.5-1.0000.9890.9710.9530.9360.918
-10--0.9890.9710.9530.9360.918
-15---0.9710.9530.9360.918
- (04 - 16) -
Page 18
4-9. ADDITIONAL CHARGE CALCULATION
R410A
2300
7.51015202530 (MAX)
20g / m
R410A
2300
7.51015202530 (MAX)
40g / m
MODELS :
REFRIGERANT TYPE
REFRIGERANT AMOUNT
AR 30F / AO 30F
g
REFRIGERANT CHARGE
PIPE LENGTH m
ADDITIONAL CHARGE
g
0 (Charge less)+ 50+ 150+ 250+ 350+ 450
MODELS : AR 30U / AO 30U, ART30U /AOT30U
REFRIGERANT TYPE
REFRIGERANT AMOUNTg
REFRIGERANT CHARGE
DUCT TYPE
PIPE LENGTH m
AR30W
ADDITIONAL CHARGE
g
0 (Charge less)+ 100+ 300+ 500+ 700+ 900
DUCT TYPE
AR30W
- (04 - 17) -
Page 19
4-10. OPERATION RANGE
AR*30FAO*30F
Cooling
Dry
Cooling
Dry
Heating16 to 30 °C -7 to 24 °C
AR*30U
ART30U
AO*30U
AOT30U
About 80% or less
Model
Mode
Operation Range
Model
Mode
Operation Range
COOLING MODEL
Indoor unitOutdoor unitIndoor temperature Indoor humidity Outdoor temperature
HEAT PUMP MODEL
Indoor unitOutdoor unitIndoor temperature Indoor humidity Outdoor temperature
18 to 32 °CAbout 80% or less0 to 43 °C
18 to 32 °C0 to 43 °C
DUCT TYPE
DUCT TYPE
AR30W
AR30W
- (04 - 18) -
Page 20
305080100120140150
m3/h
180017001540140012401100850
l/s500472428389344306236
CFM10591001906824730647500
m3/h
16201520132012401080850-
l/s450422367344300236-
CFM953895777730636500-
m3/h
1440135012001060920--
l/s400375333294256--
CFM848795706624541--
FAN SPEED
Hi
Med
Low
230V
Static pressure (Pa)
4-11. FAN PERFORMANCE AND AIR FLOW
70.0
80.0
90.0
100.0
110.0
120.0
130.0
140.0
5001,0001,5002,000
7.0
8.0
9.0
10.0
11.0
12.0
13.0
14.0
COOLING
86.0
88.0
90.0
92.0
94.0
96.0
98.0
100.0
102.0
104.0
106.0
108.0
5001,0001,5002,000
35.0
40.0
45.0
50.0
55.0
HEATING
4-11-1. NORMAL MODE
MODELS : AR 30F / AR 30U
160
Q-h Characteristic curve
DUCT TYPE
AR30W
140
120
100
80
60
40
20
STATIC PRESSURE(Pa)
0
500100015002000
Air temp
Capacity
Cooling capacity(%)
Hi
Med
Low
DUCT TYPE
AR30W
Air temperature(°C)
Air temp
Capacity
Heating capacity(%)
Testcondition:NofilterandFanmode.
AIR FLOW (m3/h)
- (04 - 19) -
Air temperature(°C)
Page 21
MODEL : ART30U
305080100120140150
m3/h
185017501580143012601020820
l/s514486439397350283228
CFM10891030930842742600483
m3/h
16801580140012801100880-
l/s467439389356306244-
CFM989930824753647518-
m3/h
1520143012501120960--
l/s422397347311267--
CFM895842736659565--
240V
FAN SPEED
Hi
Med
Low
Static pressure (Pa)
Q-h Characteristic curve
160
140
120
DUCT TYPE
AR30W
100
80
60
40
20
STATIC PRESSURE(Pa)
0
500100015002000
Hi
Med
Low
DUCT TYPE
AR30W
140.0
130.0
120.0
110.0
100.0
90.0
Cooling capacity(%)
80.0
70.0
5001,0001,5002,000
108.0
106.0
104.0
102.0
100.0
98.0
96.0
94.0
92.0
90.0
Heating capacity(%)
88.0
86.0
5001,0001,5002,000
Air temp
Capacity
Air temp
Capacity
COOLING
HEATING
14.0
13.0
12.0
11.0
10.0
9.0
8.0
7.0
55.0
50.0
45.0
40.0
35.0
Air temperature(°C)
Air temperature(°C)
Testcondition:NofilterandFanmode.
AIR FLOW (m3/h)
- (04 - 20) -
Page 22
4-11-2. LOW STATIC MODE
305070100
m3/h
1600151014201240
l/s444419394344
CFM942889836730
m3/h143013501250-
l/s397375347-
CFM842795736-
m3/h
128012001110-
l/s356333308-
CFM753706653-
FAN SPEED
Hi
Med
Low
230V
Static pressure (Pa)
MODELS : AR 30F / AR 30U
Q-h Characteristic curve
120
100
DUCT TYPE
AR30W
DUCT TYPE
AR30W
80
Hi
Med
Low
DUCT TYPE
AR30W
60
40
20
STATIC PRESSURE(Pa)
0
500100015002000
108.0
106.0
104.0
102.0
100.0
98.0
Cooling capacity(%)
96.0
1,2001,3001,4001,5001,6001,700
104.0
103.0
Air temp
Capacity
Air temp
Capacity
COOLING
HEATING
14.0
13.5
13.0
12.5
12.0
11.5
11.0
42.0
41.0
102.0
101.0
100.0
99.0
Heating capacity(%)
98.0
1,2001,3001,4001,5001,6001,700
Testcondition:NofilterandFanmode.
AIR FLOW (m3/h)
- (04 - 21) -
40.0
39.0
38.0
37.0
36.0
Air temperature(°C)Air temperature(°C)
Page 23
MODEL : ART30U
305080100
m3/h
1680158014201250
l/s467439394347
CFM989930836736
m3/h
152014301250-
l/s422397347-
CFM895842736-
m3/h
138012801120-
l/s383356311-
CFM812753659-
Static pressure (Pa)
240V
FAN SPEED
Hi
Med
Low
Q-h Characteristic curve
120
Hi
100
80
DUCT TYPE
AR30W
60
Med
Low
DUCT TYPE
AR30W
40
20
STATIC PRESSURE(Pa)
0
500100015002000
108.0
106.0
104.0
102.0
100.0
98.0
Cooling capacity(%)
96.0
1,2001,3001,4001,5001,6001,700
104.0
103.0
Air temp
Capacity
Air temp
Capacity
COOLING
HEATING
14.0
13.5
13.0
12.5
12.0
11.5
11.0
42.0
41.0
102.0
101.0
100.0
99.0
Heating capacity(%)
98.0
1,2001,3001,4001,5001,6001,700
Testcondition:NofilterandFanmode.
AIR FLOW (m3/h)
- (04 - 22) -
40.0
39.0
38.0
37.0
36.0
Air temperature(°C)Air temperature(°C)
Page 24
4-12. NOISE LEVEL CURVE
NC-45
4-12-1. OUTDOOR UNIT
COOLINGHEATING
MODELS : AO 30F, AO 30U
MODELS : AO 30U, AOT30U
AOT30U
Condition
Fan speed : High
Voltage : 230 -240V /50Hz
80
70
NC-65
60
DUCT TYPE
AR30W
50
40
dB:(0dB=0.0002bar)
Octave band sound pressure level,
30
NC-60
NC-55
NC-50
NC-40
NC-35
NC-30
80
70
60
50
40
dB:(0dB=0.0002bar)
Octave band sound pressure level,
30
Condition
Fan speed : High
Voltage : 230 -240V /50Hz
NC-65
NC-60
NC-55
NC-50
NC-45
NC-40
NC-35
NC-30
DUCT TYPE
AR30W
NC-25
20
10
0
631252505 001,0002,0 004,0008,000
Octave band center frequency, Hz
NC-20
NC-15
20
10
0
631252505001,0002,0004,0008,000
Octave band center frequency, Hz
NC-25
NC-20
NC-15
- (04 - 23) -
Page 25
4-12-2. INDOOR UNIT
HIGH
LOW
HIGH
LOW
COOLINGHEATING
MODELS : AR 30F, AR 30U
MODELS : AR 30U, ART30U
ART30U
Condition
Fan speed : High, Low
Voltage : 230-240V /50Hz
Static pressure : 100Pa
80
70
NC-65
60
DUCT TYPE
AR30W
50
40
dB:(0dB=0.0002bar)
Octave band sound pressure level,
30
NC-60
NC-55
NC-50
NC-45
NC-40
NC-35
NC-30
80
70
60
50
40
dB:(0dB=0.0002bar)
Octave band sound pressure level,
30
Condition
Fan speed : High, Low
Voltage : 230-240V /50Hz
Static pressure : 100Pa
NC-65
NC-60
NC-55
NC-50
NC-45
NC-40
NC-35
NC-30
DUCT TYPE
AR30W
NC-25
20
10
0
631252505 001,0002,0 004,0008,000
Octave band center frequency, Hz
NC-20
NC-15
20
10
0
631252505001,0002,0004,0008,000
Octave band center frequency, Hz
NC-25
NC-20
NC-15
- (04 - 24) -
Page 26
4-13. ELECTRIC CHARACTERISTICS
Main Fuse (Circuit breaker)
Current
mm
2
Model Name
AR30F
AR30U
AO30F
AO30U
Power Supply
230
230
50
50
Rated Value
Mode
*1) Wiring Spec
302130
3.5
3.5
21
Indoor Fan Motor
0.15
0.15
0.67
0.67
0.7
0.7
-
36(240V)
Outdoor Fan Motor
0.14
0.14
ART30U
AOT30U
240
50
30
3.5
21
36(240V)
0.15
0.67
0.14
0.7
MODELS : AR 30F / AO 30F
AR 30U / AO 30U, ART30U / AOT30U
Indoor unit
Outdoor unit
VoltageV
FrequencyHz
CurrentA14.0-14.012.414.313.1
InputkW2.99-2.992.633.152.80
Max Operating Current A17.0-17.616.017.016.0
Starting CurrentA70-70707070
A
Power Cable
*2)Limited wiring lengthm
InputkW
DUCT TYPE
AR30W
Belt heaterW
Full Load Amp.A
InputkW
Full Load Amp.A
Cooling-Cooling Heating Cooling Heating
DUCT TYPE
AR30W
*1) Wiring Spec :Selected Sample
(Selected based on Japan Electrotechnical Standard and Codes Committee E0005)
*2) Limited Wiring length : This is the wiring length in case voltage descent is less than 2%.
When the wiring length becomes long, please select the wiring of a more larger
diameter.
- (04 - 25) -
Page 27
4-14. SAFETY DEVICE
AO30F
AO
AOT30U
30U
FUSE
(SIDE OF INDOOR UNIT)
AR30F
AR
ART30U
30U
5A 250V
150°C ± 5°C OFF
OFF : 25°C(78A120°C(29.6A
ON : 90 ± 10°C
3.15A 250V
150°C ± 5°C OFF
OUTDOOR UNIT
MODEL NAMEPROTECTION FORM
-
FUSE ON PCB--3.15A 250V
FAN MOTOR PROTECTORTHERMAL PROTECTOR
COMPRESSOR -
INDOOR UNIT
MODEL NAMEPROTECTION FORM
PCB FUSE-
DUCT TYPE
FAN MOTOR PROTECTORTHERMAL PROTECTOR
AR30W
DUCT TYPE
AR30W
- (04 - 26) -
Page 28
4-15. EXTERNAL INPUT & OUTPUT
PREP
ARA
When the external input / output is used,
connect the external signal wire as shown
in the figure below.
TION
CN106
(Black)
CN5
(Black)
PCB
Indoor unit
PCB
CONTROL
INPUT
[Example]
You can control air conditioner on/off by
external control. You can select either
Edge and Pulse.
Indoor
unit
+
1
2
3
Ch1
-
CN114
DUCT TYPE
AR30W
(White)
Field supply
DUCT TYPE
AR30W
DIP Switch (Indoor Unit)
SW state
ON
PulseEdge
SW2
DIP-Switch
NO.
OFF
2
1 Edge
1.The last command has priority.
2.The wire connection is separate from the power cable line.
Ch1
(Input)
Remote
controller
Indoor
unit
On
Off
On
Operation
Stop
2 Pulse
Ch1
(Input)
Remote
controller
Indoor
unit
Operation
Stop
200ms200ms200ms
On
- (04 - 27) -
Off
Page 29
OPERA
[Example]
TION DISPLA
Y
Operation
indicator
Field supply
Operation
Ic
Vc
or
Vc : DC20V or Iess
Ic : 10mA or Iess
Indoor
unit
CN115
(WHITE)
+
2
1
-
Indoor
unit
Stop
SHORT
CN115
(Output)
DUCT TYPE
AR30W
FRESH
AIR OUTPUT SETTING
OPEN
DUCT TYPE
AR30W
You can control sub fan by synchronizaton with fan operation of indoor unit.
[Example]
+
Indoor
unit
-
CN14
(GREEN)
1
2
Indoor
unit fan
CN14
(Output)
Field supplied
Operation
Stop
14V
0V
Fuse
Power
Fan, other
- (04 - 28) -
Page 30
EXTERNAL
ELECTRICAL HEA
TER OUTPUT SETTING
You can control Electrical heater (Booster) by sychronization with heating operation.
When temperature is -10 to -3 degrees from Setpoint,External electrical heater is ON.
When temperature is -1 degrees from Setpoint,External electrical heater Stops.
Jumper wire (Indoor Unit)
This is used to continue indoor unit fan operation for 1 minute after thermo OFF in heating mode.
1 minute delay control set by cutting JM3 on PCB.
[Example]
Fuse
Indoor
unit
+
1
2
-
CN15
(ORANGE)
DUCT TYPE
AR30W
Indoor
unit
Heating
Indoor
Operation
Stop
Operation
Field supplied
unit fan
Stop
14V
CN15
(Output)
0V
<Operation condition>
All conditions shall be met.
Under heating operation.
Fan mode : Either Hi, Med, Low, Quiet.
Power
External Heater, other.
1min
DUCT TYPE
AR30W
Cold air prevention function not working (Heat exchanger temperature over 27 C ).
Temperature subtracted set temperature from room temperature is between -10 C to -3 C.
-10 C < *T < -3 C *T=Room temperature
Compressor 3 minutes stop mode is released.
Defrosting mode is released.
<Release condition>
Do not meet above condition , or room temperature is 1 C below from set temperature.
CAUTION!
!
Please locate external a heater between the indoor unit and the ductwork.
Please be sure to use delay control of a fan.
External
Heater
Supply air
Indoor unit
Return air
- (04 - 29) -
Page 31
4-16. FUNCTION SETTING
4-16-1. INDOOR UNIT
1
Low static pressure function setting
SW 1
DIP SW
SW 2
Rotary SWSW 3Indoor unit number setting
Jumper Wire
SWITCH POSITION
DUCT TYPE
AR30W
Duct type Indoor unit control circuit board
2
Forbidden
3
4
1Room temperature correct coefficient of heating
2External input select
3Auto restart validity/invalidity
JM1 Room temperature correct coefficient of cooling
JM2 Commercial mode setting
JM3 Fan delay setting
INDOOR UNIT
DUCT TYPE
AR30W
CN114
CN106
CN115
CN4
CN5
CN16
CN14
CN15
MAIN PCBPOWER PCB
SW1SW2
1 2 31 2 34
ON
OFF
SW1 SW2
SW3
ON
OFF
JM1
JM2
JM3
- (04 - 30) -
CN16
Page 32
4-16-2. SWITCH FUNCTION (INDOOR UNIT)
SW2-1SW state
OFF+4 deg (Ceiling setting)
ON 0 deg (Room setting)
SW2-2SW state
OFFEdge
ONPulse
SW2-3SW state
OFFValidity
ONInvalidity
SW3SW state
0single
1-15Indoor unit address
SW1-1SW state
OFFNormal
ONLow static pressure
SW1-2OFF
SW1-3OFF
SW1-4OFF
DIP SWITCH SETTING
1. SW1 setting
1-1 Low static pressure function setting
In case of installing in low static , you can minimize air flow and noise.
(Factory setting)
1-2 Dip SW 1-2,1-3,1-4 setting forbidden
(Factory setting)
2. SW2 setting
DUCT TYPE
DUCT TYPE
AR30W
2-1 Room temperature correct coefficient of heating.
Decide the heating temperature correct coefficient vale of heating.
Heat temperature corrction
(Factory setting)
2-2 Control input setting
This switch is used to select the format of external input command as shown in the table below.
(Factory setting)
2-3 Auto restart setting
Auto restart function can be selected by turning this switch ON/OFF.
AR30W
(Factory setting)
ROTARY SWITCH SETTING
This switch can be used when group control system. Set the indoor unit address in the 1,2,-,15 order.
(Factory setting)
- (04 - 31) -
Page 33
JUMPER WIRE SETTING
ConnectorINPUTOUTPUTREMARKS
CN114
CONTROL INPUT
(OPERATION/STOP)
-
CN115-OPERATION DISPLAY
CN14-FRESH AIR
CN15-ELECTRICAL HEATER
See external
input/output settings
for details.
JM2JM state
ConnectResidencial
DisconnectCommercial
JM3JM state
ConnectInvalidity
DisconnectValidity
JM1JM state
Connect0 deg
Disconnect+ 2 deg
Room temperature correct coefficient of cooling.
Decide the cooling temperature correct coefficient value of cooling.
Cool temperature corrction
(Factory setting)
Commercial mode setting
"Hot start" can be canceled,fan operates continously when indoor unit is ON on every mode.
When you select "FAN:AUTO"mode fan goes in "HIGH"
(Factory setting)
DUCT TYPE
Fan delay setting
AR30W
DUCT TYPE
AR30W
This setting can be used when the auxiliary heater is mounted.
When the fan operation is stopped when the indoor unit is operating
with an auxiliary heater,the fan operation continues one minutes.
Set the remote controller DIP switch No.1 and 2 according to the following table.
(Factory setting)
Number of
remote
controller
1 (Normal)
2 (Dual)
1-2 Group control setting
Number of indoor unit connection (One/Multiple)
This is switched according to the number of connected indoor units.
DUCT TYPE
AR30W
DIP-SW
No.3
OFF
Master unitSlave unit
DIP-SW
No.1
DIP-SW
No.2
ON
OFF
(Factory setting)
Number of indoor unit
One unit connection
OFF
OFF
DIP-SW
No.1
ONON
DIP-SW
No.2
DUCT TYPE
AR30W
ONMultiple unit connection
1-3 Model setting
The system type of the outdoor unit can be selected by setting up DIP switch No.4 as follows.
(Factory setting)
DIP-SW
No.4
OFF
ONCooling only model
Heat Pump model
Model
1-4 Auto changeover setting
Selecting auto changeover validity / invalidity.
(Factory setting)
DIP-SW
No.5
OFF
ONValidity
Auto changeover
Invalidity
1-5 Memory backup setting
Set to ON to use batteries for the memory backup.if batteries are not used,
all of the settings stored in memory will be deleted if there is a power failure.
This function is wired remotecontroll only.
(Factory setting)
DIP-SW
No.6
OFF
ONValidity
Memory backup
Invalidity
- (04 - 34) -
Page 36
4-17. OPTIONAL PARTS
SIMPLE REMOTE CONTROLLERS
UTB - YPB : FUJITSU BRAND
UTB - GPB : GENERAL BRAND
UTB - TPB : Australia only
Remote controller which gives priority to ease-of-use and allows operation
of the necessary functions only.
REMOTE SENSOR UNIT
UTD - RS100
Accurate and Comfortable
New amenity space can be offered by installing the thermo sensor in the remote controller.
Because the remote controller has the switching function, the user can select the position of the
sensor. (Room temperature sensor selection)
DUCT TYPE
AR30W
Example of room temperature
sensor selection
Simple remote
controllers
Remote Sensor
in the bed room (effective at night)
DUCT TYPE
AR30W
Sensor part
Wired Remote Controller
LONG LIFE FILTER
THERMO
Day
The detecting point can be freely changed.
SENSOR
Night
Remote Controller
in the living room (effective during the day)
Remote Sensor (Optional Parts)
UTD - LF25NA
Intake air filter can be mounted to the indoor unit.
- (04 - 35) -
Page 37
SQUARE FLANGE (UTD - SF045T)
ROUND FLANGE (UTD - RF204)
Round flange is used when the fresh air duct is installed.
DUCT TYPE
AR30W
DUCT TYPE
DUCT TYPE
AR30W
DUCT TYPE
AR30W
AR30W
Air intake hole
Round flange
- (04 - 36) -
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.